Top Victory Electronics CM995T Color Monitor User Manual S995T EPI
Top Victory Electronics (Taiwan) Co Ltd Color Monitor S995T EPI
Exhibit 7 The user manual of EUT
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 96618 |
| Application ID | 6bbm8vVF+nd4dCBDP59/SA== |
| Document Description | Exhibit 7 The user manual of EUT |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 17.98kB (224713 bits) |
| Date Submitted | 2000-04-16 00:00:00 |
| Date Available | 2000-04-25 00:00:00 |
| Creation Date | 2000-04-11 15:57:52 |
| Producing Software | Acrobat PDFWriter 4.0 for Windows |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | 穨S995T-EPI.PDF |
| Document Creator | 穨Microsoft Word |
| Document Author: | 穨SR |
Your Work Never Looked Better 9Glr/9GlrA USER MANUAL TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 BEFORE YOU OPERATE THE MONITOR ---------------------- 3 FEATURES -------------------------------------------------------- 3 PACKING LIST --------------------------------------------------- 3 INSTALLATION INSTRUCTIONS --------------------------- 3 CONTROLS AND CONNECTORS -------------------------- 4 OPERATING INSTRUCTIONS ------------------------------------- 5 GENERAL INSTRUCTIONS ---------------------------------- 5 HOW TO ADJUST A SETTING ------------------------------ 7 ADJUSTING THE PICTURE ---------------------------------- 7 POWER MANAGEMENT FEATURE ----------------------- 9 PLUG AND PLAY ------------------------------------------------10 TECHNICAL SUPPORT(FAQ) -------------------------------------12 APPENDIX ---------------------------------------------------------------13 SPECIFICATIONS -------------------------------------------13-14 FACTORY PRESET TIMING TABLE -----------------------15 CONNECTOR PIN ASSIGNMENT --------------------------15 Thank you very much for choosing the AOC Color Monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for you future reference. Plug & Play Drivers for the AOC Spectrum Series Monitors are available at : www.epius.com Before operating the monitor please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. As an ENERGY STAR Partner Envision Peripherals, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. WARNING : To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only. PRECAUTIONS l Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. l Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. l Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. l The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. l The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. l Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. l Do not overload power strips and extension cords. Overloading can result in fire or electric shock. l Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. l Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. l To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. 2.5A. BEFORE YOU OPERATE THE MONITOR FEATURES FEATURES • • • • • 48.3cm(19”) Color Monitor Crisp, Clear Display for Windows Supports Resolutions up to 1600 5 1200 Power Management Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE MONITOR PACKAGE The product package should include the following items: 1. 2. 3. 4. 5. Monitor Owner's Manual Power Cord Swivel Base Audio Cable/DC Power Cable ( for 9GlrA only ) INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor, do the following: • Carefully turn the monitor on its side or upside down. ( see figure 1 ) • Locate the cavities at the bottom front of the monitor. • Insert the pegs on the swivel base into these cavities. Push the swivel base forward until the swivel base locks in place. • To remove the swivel base, hold the bottom of the swivel base, then push it out. Install Remove Install Remove 9Glr Figure 1 9GlrA Installing and Removing the Swivel Base POWER CORD Power Source: 1. Make sure the power cord is the correct type that required in your area. 2. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area ( No user adjustment is required. ) 3. Connect the power cord into your monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet. The power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your monitor. CONTROLS AND CONNECTORS VIDEO CABLE Connecting the Video Cable: the monitor comes with a built-in video cable. Plug the signal cable′s 15-pin connector into the computer's video port and tighten the two screws on the cable connector. (see figure 2) Caution: Don’t bend the signal cable, otherwise it will break the inner wire. Connecting the Power Cord: Plug the power cord into the monitor's AC power socket. Then plug the power cord into a grounded AC outlet or ULapproved power strip or the power output socket on your PC. Caution: If the AC outlet is not grounded, install the proper grounding adapter (not supplied). Connecting the Audio Cable ( 9GlrA only ): Plug audio cable between the computer multi-media (or sound) card's audio output and monitor's audio input. Connecting the DC Power Cable ( 9GlrA only ): Plug DC power cable between monitor to swivel base for audio power 9Glr Figure 2 1. 2. 3. Power Cord Signal Cable VGA Card Adapter 9GlrA Connecting Cables 4. 5. PC Audio Output DC Output OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • To turn the monitor on, press the standby POWER switch to ON position. The power indicator will light up. • Your monitor features a unique quick switch system which provides a picture within seconds after the monitor is switched on. 9Glr 9GlrA Figure 3 External Control Knob EXTERNAL CONTROLS 9Glr 1. OSD Exit 2. Shuttle Knob 3. Standby Power ON/OFF Switch 4. Power Indicator 1. 2. 3. 4. 9GlrA OSD Exit Shuttle Knob Standby Power ON/OFF Switch Power Indicator 5. Earphone Jack 6. Volume 7. Audio Power Indicator 8. Audio Power ON/OFF FRONT PANEL CONTROL • Standby power key : When pressed, the monitor enters the off mode, and the LED turns orange. Press again and hold to restore normal status. • Shuttle Knob : The Shuttle Knob is used to control the monitor functions. Rotate to switch functions or adjust settings. Press to select or execute a function . • OSD Key : The OSD Key is used to activate the OSD window, or to exit the OSD window and save the settings. • Power Indicator : Green — Orange — Power On mode. Stand-by mode, Suspend mode, or Off mode. SWIVEL BASE CONTROL (9GlrA ONLY ) : • Audio Power ON or OFF Audio Power • Power Indicator Green • Volume — Audio Power ON. Adjustable Audio volume. NOTES • Do not install the monitor in a location near heat sources such as • • • radiators or air ducts , or in a place subject to direct sunlight , or excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it. HOW TO ADJUST A SETTING 1. Press the Shuttle Knob or OSD Key to make the OSD window appear. See figure 4. 2. Rotate the Shuttle Knob to select the desired function. See figure 4. 3. Press the Shuttle Knob again to select the function that you want to adjust. 4. Rotate the Shuttle Knob to change the settings of the current function. 5. When the OSD window is active, it shows the input signal timing. The "H" stands for the horizontal frequency and "V" for the vertical frequency. 6. To exit and save, either press the OSD Key, select the exit function, or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. H: 68.8KHz V: 85Hz Contrast 70 6500 9300 Figure 4 The OSD Message ADJUSTING THE PICTURE The description for function control LEDS 1. CONTRAST Adjust the picture contrast. 2. BRIGHTNESS Adjust the picture brightness. 3. H- CENTER Adjust the horizontal position of the picture. 4. H- SIZE Adjust the picture’s horizontal size. 5. V- CENTER Adjust the vertical position of the picture. 6. V- SIZE Adjust the picture’s vertical size. ZOOM Adjust the picture’s horizontal and vertical size simultaneously. 8. PINCUSHION Adjust the pincushion and barrel 9. TRAPEZOID Adjust the picture’s trapezoid distortion. 10. PIN-BALANCE Adjust to compensate the pincushion unbalance. 11. PARALLELOGRAM Adjust the picture to be a rectangle. 12. ROTATION Adjust the picture tilt to horizontal position. 6500°K/9300°K ( COLOR TEMPERATURE ) The color temperature for 6500°K is x=0.313, y=0.329 and 9300°K is x=0.283, y=0.297. It presents two different color sets on the screen. You can select 9300°K or 6500°K by pressing the Shuttle Knob. If the 9300°K normal white or 6500°K warmer white do not satisfy your desire, properly adjust R . B GAIN controls to obtain your optimum whiteness level. If color impurity occurs when moving or swiveling the monitor, press the Shuttle Knob and degauss to fix the picture condition. Moire is the result of interference between the phosphor layout and the video signal. In some cases, you may find the moire very noticeable. Press the Shuttle Knob to enter in the moire reduce setting. Please adjust the level to the optimum condition. Note: Too high of a setting will cause the picture to shake. 7. 13. 14. 15. 16. USER COLOR ( Red / Blue ) DEGAUSS MOIRE REDUCE 17. RECALL Press RECALL to restore the monitor to factory settings. 18. EXIT Close OSD window. POWER MANAGEMENT FEATURE The power management feature of this product complies with every power saving requirements of ENERGY STAR and VESA DPMS when activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS computer. There are three power management modes available, these are described below. The required settings, including the timer setting, should be made by the computer. • Stand-by Mode When the H-sync signal from the computer is off, the monitor enters into Stand-by Mode which reduces the power consumption to less than 15W. The screen becomes dark, and the power indicator turns to orange. From Stand-by Mode, the screen reappears instantaneously when the keyboard or the mouse is touched again. • Suspend Mode When the V-sync signal from the computer is off, the monitor enters into Suspend Mode which reduces the power consumption to less than 15W. The screen becomes dark, and the power indicator turns to orange. From Suspend Mode, the screen reappears instantaneously when the keyboard or the mouse is touched again. • Active-off Mode When both the H and V sync signals from the computer are off, the monitor enters into Active-off Mode which reduces the power consumption to less than 8W. The screen becomes dark, and the power indicator turns to orange. From Active-off Mode, the screen reappears instantaneously when the keyboard or the mouse is touched again. • The power-saving mode can be indicated by the light-emitting diode (LED) on the front panel: Signal Cable H-Sync V-Sync Video Attached Yes Yes Active On* Stand-by Attached No Yes Blank Suspend Attached Yes No Blank Off Attached No No Blank Mode Power Indicator Consumption Green ≤ 130 W Orange ≤ 15 W Orange ≤ 15 W Orange ≤ 8W FEATURES Green monitor • The monitor has a power saving function that conforms to the VESA DPMS standard. This feature will only work if your PC is a green PC. This feature is similar to a screen saver, except that your monitor will turn it off instead of activating the screen saver. To activate this feature in Windows® 98 : In Windows® 98, this feature can be activated and customized under the screen saver setting of the display properties. 1. 2. 3. 4. Right click on the desktop and choose Properties. Click on the tab that says Screen Saver. If your system supports Green PC, there will be a section entitled “Energy Saving Features of Monitor.” If there isn’t a section like that, then your PC does not support Green Monitor. The monitor will behave just like a normal monitor, so you will have to turn it off manually to save energy. In the “Energy Saving Features of Monitor” sections are two boxes, Standby and Shut off. To activate either one, click the box next to each one. You can specify the amount of inactive time before your monitor enters standby mode or shuts off. PLUG AND PLAY Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. 10 THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL. This monitor meets the Power Management standards as set by the Video Electronics Standards Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees ( NUTEK ). This feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse. USING THE RIGHT POWER CORD : The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 11 TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play No picture Picture is fuzzy Picture bounces or a wave pattern is present in the picture Monitor is stuck in “Power Saving Mode” Missing one of the primary colors (RED, GREEN, or BLUE) North America technical support telephone number: Possible Solution *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at: www.epius.com) *Computer Power Switch should be in the ON position *Computer Video Card should be snugly seated in its slot *The Signal Cable should be completely connected to the computer *Check the color of the Power LED indicator. If it is orange, then the monitor and the PC system are in power-saving mode. You need press your keyboard or move the mouse to reactivate the system. *Adjust the Contrast and Brightness Controls. *Move electrical devices that may cause electrical interference. *Make sure monitor’s video cable is properly connected to the computer. *Inspect monitor’s video cable and make sure none of the pins are bent. *Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key. *Inspect the monitor’s video cable and make sure that none of the pins are bent. 1-800-343-5777 12 APPENDIX SPECIFICATIONS CRT Input CRT Size 48.3cm(19"), 29mm neck, Viewable Image Size Type Video Separate Sync. H./V.- Sync. H-Frequency V-Frequency 45.7cm (18"), diagonal Scanning Frequency Max. Resolution Video Dot Rate Factory Preset mode : User mode : Programmable Power Source Operating Humidity Dimensions 9Glrs 9GlrsA: Weight 9Glr: 9GlrA: Signal Cable: 0.26 mm dot pitch. 0.7Vpp, R,G,B Analog TTL Level Positive / Negative 30kHz - 95kHz 50Hz-160Hz 1600 x 1200 200MHz 12 Universal AC 100 - 240V, 50Hz / 60Hz 0ºC to 40ºC ambient 10% to 85%relative, non-condensing Monitor & Base 460(W) × 466(H) × 470(D)mm Monitor & Base 460(W) × 503(H) × 470(D)mm Unit (net) Unit (net) 20kgs ( Net ) 20.8kgs ( Net ) Attached Mini D-sub 15 Male 470 460 466 (in mm) 9Glr 13 • • • • • • • • • • • • • • • • • • • • • • • Switch External Controls: Functions Plug & Play Power Management Power Consumption Pre-set Display Area Audio Output (for 9GlrA only) Regulatory Compliance ( Maximum ) Shuttle Knob Standby Power Switch OSD Key Volume(9GlrA) Contrast Brightness H-Center H-Size V-Center V-Size ZOOM Pincushion Trapezoid Pin-Balance Parallelogram Rotation 6500°K User Color 9300°K Degauss Moire Reduce Recall Exit DDC1/2B EPA, VESA DPMS 130 Watts 346mm x 260mm Rated Power 1W rms (Per channel) UL, CSA, FDA, FCC, TÜV/GS, CE, TCO’92 (TCO’95/TCO’99) 470 460 503 (in mm) 14 9GlrA FACTORY PRESET TIMING TABLE STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY VGA 720 × 400 31.5kHz 70Hz VGA 640 × 480 31.5kHz 60Hz VESA/85 640 × 480 43.3kHz 85Hz VESA/85 800 × 600 53.7kHz 85Hz VESA/85 1024 × 768 68.7kHz 85Hz VESA/85 1280× 960 85.9kHz 85Hz VESA/85 1280× 1024 91.1kHz 85Hz VESA/75 1600× 1200 93.8kHz 75Hz CONNECTOR PIN ASSIGNMENT 10 11 15 15 - Pin Color Display Signal Cable PIN NO. 1. 2. 3. 4. 5. 6. 7. 8. DESCRIPTION PI N NO. DESCRIPTION 9. 10. 11. 12. 13. 14. 15. NC Ground Ground DDC-Serial Data H-Sync V-Sync / *V-Clk DDC-Serial Clock For DDC Red Green Blue Ground Ground R-Ground G-Ground B-Ground 15
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 16 Creator : .穨.Microsoft Word Create Date : 2000:04:11 15:57:52 Title : .穨.S995T-EPI.PDF Author : .穨.SR Producer : Acrobat PDFWriter 4.0 for WindowsEXIF Metadata provided by EXIF.tools