Topcon Marine Instruments Gpt 2000 Users Manual 2000EngFW

2015-02-02

• TopCover
• FOREWORD
  • General Handling Precautions
  • Display for Safe Use
  • Safety Cautions
  • User
  • Exceptions from Responsibility
  • Safety Standard for Laser Beam
  • Safety Standard for Laser Beam
  • Labels
  • Symbol mark while the laser is emitting.
  • Contents
  • Standard Set Composition
• 1 NOMENCLATURE AND FUNCTIONS
  • 1.1 Nomenclature
  • 1.2 Display
  • 1.3 Operating Key
  • 1.4 Function Key (Soft Key)
  • 1.5 Serial signal RS-232C connector
• 2 PREPARATION FOR MEASUREMENT
  • 2.1 Power Connection
  • 2.2 Setting Instrument Up For Measurement
  • 2.3 Power Switch Key ON
  • 2.4 Battery Power Remaining Display
  • 2.5 Vertical and Horizontal Angle Tilt Correction
  • 2.6 How to Enter Alphanumeric characters
  • 2.7 Point Guide (Only for Point Guide type)
  • 2.8 Laser Plummet ON/OFF (Only for Laser Plummet type)
• 3 ANGLE MEASUREMENT
  • 3.1 Measuring Horizontal Angle Right and Vertical Angle
  • 3.2 Switching Horizontal Angle Right/Left
  • 3.3 Measuring from the Required Horizontal Angle
    • 3.3.1 Setting by Holding the Angle
    • 3.3.2 Setting a Horizontal Angle from the Keys
  • 3.4 Vertical Angle Percent Grade(%) Mode
  • 3.5 Repetition Angle Measurement
  • 3.6 Buzzer Sounding for Horizontal Angle 90° Increments
  • 3.7 Compasses ( vertical angle)
• 4 DISTANCE MEASUREMENT
  • 4.1 Setting of the Atmospheric Correction
  • 4.2 Setting of the Correction for Prism Constant / Non-prism Constant
  • 4.3 Distance Measurement (Continuous Measurement)
  • 4.4 Distance Measurement (N-time Measurement/Single Measurement)
  • 4.5 Fine Mode/Tracking Mode/Coarse Mode
  • 4.6 Stake Out (S.O)
  • 4.7 Offset Measurement
    • 4.7.1 Angle Offset
    • 4.7.2 Distance Offset Measurement
    • 4.7.3 Plane Offset Measurement
    • 4.7.4 Column Offset Measurement
• 5 COORDINATE MEASUREMENT
  • 5.1 Setting Coordinate Values of Occupied Point
  • 5.2 Setting Height of the Instrument
  • 5.3 Setting Height of Target (Prism Height)
  • 5.4 Execution of Coordinate Measuring
• 6 SPECIAL MODE (Menu Mode)
  • 6.1 Application Measurement (PROGRAMS)
    • 6.1.1 Remote Elevation measurement (REM)
    • 6.1.2 Missing Line Measurement (MLM)
    • 6.1.3 Setting Z Coordinate of Occupied Point
    • 6.1.4 Area Calculation
    • 6.1.5 Point to Line Measurement
  • 6.2 Setting the GRID FACTOR
  • 6.3 Setting Illumination of Display and Cross Hairs
  • 6.4 Setting Mode 1
    • 6.4.1 Setting Minimum Reading
    • 6.4.2 Auto Power Off
    • 6.4.3 Vertical and Horizontal Angle Tilt correction ( Tilt ON/OFF)
    • 6.4.4 Systematic Error of Instrument Correction (only for GPT-2003/2005/2006)
    • 6.4.5 Selecting Battery Type
  • 6.5 Setting Contrast of Display
• 7 DATA COLLECTION
  • 7.1 Preparation
    • 7.1.1 Selecting a File for Data Collection
    • 7.1.2 Selecting a Coordinate File for Data Collection
    • 7.1.3 Occupied Point and Backsight Point
  • 7.2 Operational Procedure of “DATA COLLECT”
    • 7.2.1 Searching the recorded data
    • 7.2.2 Entering PCODE / ID using PCODE Library
    • 7.2.3 Entering PCODE / ID from the list of PCODE
  • 7.3 Data Collect Offset Measurement mode
    • 7.3.1 Angle Offset Measurement
    • 7.3.2 Distance Offset Measurement
    • 7.3.3 Plane Offset Measurement
    • 7.3.4 Column Offset Measurement
  • 7.4 NEZ Auto Calculation
  • 7.5 Editing PCODE Library [PCODE INPUT]
  • 7.6 Setting Parameter of Data Collect [CONFIG.]
• 8 LAYOUT
  • 8.1 Preparation
    • 8.1.1 Setting the GRID FACTOR
    • 8.1.2 Selecting Coordinate Data File
    • 8.1.3 Setting Occupied Point
    • 8.1.4 Setting Backsight Point
  • 8.2 Executing a Layout
  • 8.3 Setting a New Point
    • 8.3.1 Side Shot Method
    • 8.3.2 Resection Method
• 9 MEMORY MANAGER MODE
  • 9.1 Display Internal Memory Status
  • 9.2 Searching Data
    • 9.2.1 Measured Data Searching
    • 9.2.2 Coordinate Data Searching
    • 9.2.3 PCODE LIBRARY Searching
  • 9.3 FILE MAINTENANCE
    • 9.3.1 Rename a File
    • 9.3.2 Searching Data in a File
    • 9.3.3 Deleting a File
  • 9.4 Coordinate Data Direct Key Input
  • 9.5 Delete a Coordinate Data from a File
  • 9.6 Editing PCODE Library
  • 9.7 Data Communications
    • 9.7.1 Sending Data
    • 9.7.2 Loading Data
    • 9.7.3 Setting Parameter of Data Communications
  • 9.8 Initialization
• 10 SET AUDIO MODE
• 11 SETTING THE PRISM / NON-PRISM CONSTANT VALUE
• 12 SETTING ATMOSPHERIC CORRECTION
  • 12.1 Calculation of Atmospheric Correction
  • 12.2 Setting of Atmospheric Correction Value
• 13 CORRECTION FOR REFRACTION AND EARTH CURVATURE
  • 13.1 Distance Calculation Formula
• 14 POWER SOURCE AND CHARGING
  • 14.1 On-board Battery BT-52QA
• 15 DETACH/ATTACH OF TRIBRACH
• 16 SELECTING MODE
  • 16.1 Items of the Selecting Mode
  • 16.2 How to Set Selecting Mode
• 17 CHECK AND ADJUSTMENT
  • 17.1 Checking and adjusting of instrument constant
    • 17.1.1 Checking of the accuracy of the non-prism mode
  • 17.2 Checking the Optical Axis
  • 17.3 Checking/Adjusting the Theodolite Functions
    • 17.3.1 Checking /Adjusting the Plate Level
    • 17.3.2 Checking /Adjusting the Circular Level
    • 17.3.3 Adjustment of the Vertical Cross-hair
    • 17.3.4 Collimation of the Instrument
    • 17.3.5 Checking / Adjusting the Optical Plummet Telescope
    • 17.3.6 Checking / Adjusting the Laser Plummet (For Laser Plummet type)
    • 17.3.7 Adjustment of Vertical Angle 0 Datum
  • 17.4 How to Set the Instrument Constant Value
  • 17.5 Adjustment of Compensation Systematic Error of Instrument
• 18 PRECAUTIONS
• 19 SPECIAL ACCESSORIES
• 20 BATTERY SYSTEM
• 21 PRISM SYSTEM
• 22 ERROR DISPLAYS
• 23 SPECIFICATIONS
• APPENDIX
• LastCover