Topcon WLAN528 WLAN UNIT User Manual

Topcon Corporation WLAN UNIT

a href="https://usermanual.wiki/Topcon" itemprop="url"> Topcon >

User manual

      NJT528WLAN USER’S  MANUAL  Over View This device is a 802.11g/b WirelessLAN Module.Inter face is SDIO Bus.  Physical Specifications Table A-1 Physical Specification  Dimensions W:28mm D:13.5mm H:3.5mm Weight 1g Input / output  SDIO/Power/antenna Input voltage  3.3V±5% /320mA (typ) Operating temperature  -15-+55℃ Strage temperatuere  -30-80℃  Wireless specifications Table A-2 Wireless Specifications Standard IEEE802.11/b/g Frequency modulation technique T  DS-SS(11b),OFDM(11g) Data speed T  1,2,5.5,11,6,9,12,18,24,36,48,54Mbps Frequency Range  2412-2462MHz Channel 1-11 Output power  15dBm  Installation Guide 1. Module connected to SDIO Port on the mother Board in your Equipment. (see below)                 NAME SPEC MODEL I/F Connecter SDIO Port AXK5F20337YG RF Connector   Antenna coaxial connector  U.FL-R-SMT  *We are preparing driver software.   Mother Board SDIO Port Bottom View Top View Connect to SDIOPort Antenna
  Confirm the homepage of Microsoft to the method of installing the driver software. You must make sure that 20cm minimum separation is maintained between users and the antenna.    Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.  Regulatory Information               Compliance statement to FCC/IC   This module complies with part 15 of the FCC rules and IC RSS-210. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.    RF exposure compliance   1) To comply with FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  Requirements to end product    This module must be integrated only by OEM integrators under the following conditions.  (1) OEM integrator has to be aware not provide information to the users regarding how to install or remove this module in the users manual of the end product which integrate this module. Installation by end users is strictly prohibited.  (2) Antenna  OEM integrator shall use this module without any modifications including antenna.   If module integrator uses a unique antenna, the FCC certification is required for the end product.  OEM integrator must make sure that 20cm minimum separation is maintained between users and the antenna.  (3) Co-location.   This module must not be co-located or operated in conjunction with any other antenna or transmitter. The module integrator shall obtain FCC approval for the end product, if the module is used for co-location operation.    (4) Markings   To satisfy FCC/IC exterior labeling requirements, the following text must be placed on the exterior of the end product.     Contains Module FCC ID: H5P-, IC: 6050A- Any similar wording that expresses the same meaning may be used.    (5) Caution to user for modification The following caution is expressed on the user’s instruction manual.   The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.    (6) Compliance statement to FCC
Download:
Mirror Download [FCC.gov]
Document ID1163674
Application IDrhmiakUgCyrewQdqOqZLsA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize2.78kB (34800 bits)
Date Submitted2009-09-02 00:00:00
Date Available2009-11-05 00:00:00
Creation Date2009-08-27 11:53:22
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2009-08-27 11:53:22
Document Titleuntitled
FCC ID Filing: H5P-WLAN528

Navigation menu