Toppan Forms TR33CUT018 NFC Reader Module (FFC Type) User Manual ORK TR33CUT018

Download:
Mirror Download [FCC.gov]
Document ID	1891712
Application ID	x0WT7qJgt99M2jqHbEtFxQ==
Document Description	ORK-TR33CUT018_ User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.21kB (365133 bits)
Date Submitted	2013-01-31 00:00:00
Date Available	2013-02-04 00:00:00
Creation Date	2013-01-31 19:49:02
Producing Software	PDF-XChange 3.60.0117 (Windows)
Document Lastmod	0000-00-00 00:00:00
Document Title	ORK-TR33CUT018_ User Manual

TR33CUT018
NFC Contactless Card Reader/Writer
(PR533 NFC Reader/Writer for Toppan Forms)
User Manual
Version: 1.0
Toppan Forms Co. Ltd
TR33CUT018
User Manual
TABLE OF CONTENTS
About this Document .......................................................................................................... 1
1.1
TR33CUT018 NFC Reader/Writer module description ...................................................... 1
2.1
2.2
Purpose and Contents ............................................................................................................. 1
Description .............................................................................................................................. 1
How to use this product ........................................................................................................... 2
Application testing using APDU command ........................................................................ 3
3.1
3.2
RF ON mode with no modulation ............................................................................................ 4
RF field OFF ........................................................................................................................... 5
PCBA TR33MUT014 PCB and Antenna Dimension overview ........................................... 5
Regulatory information ....................................................................................................... 6
ii
July 19,2012/v1.0
TR33CUT018
User Manual
About this Document
1.1
Purpose and Contents
This document describes the setup and use of TR33CUT018 NFC Reader/Writer Module.
It includes the pcba information (TR33MUT014 pcba) on board layout, the antenna size and
the interface to the host.
TR33CUT018 NFC Reader/Writer module description
The interface with the host controller is USB 2.0 full speed using USB cable.
LED
Window
Mini USB
Fig 1. TR33CUT018 NFC Reader/Writer
2.1
Description
On the product, 2 parts are easily visible from external
Mini USB connector
LED window for indicating status
July 19,2012/v1.0
TR33CUT018
User Manual
2.2
How to use this product
This product has to be connected through USB interface to a PC with CCID driver embedded.
This driver is available in most of the OS. The product should be recognized and installed
automatically as soon as it is plugged.
STYL’s Toolkit application software will be provided for read/write application..
For read/write application tests, below are application example using STYL’s Toolkit software.
STYL’s Toolkit application software used for communication test
Case of smart card presented and detected in polling
PR533 reader detected
When Contactless
card is present and
detected, “Connect”
tab is highlighted.
Case of connecting to card to read card information
July 19,2012/v1.0
TR33CUT018
User Manual
Example of getting
card information
APDU command
Application testing using APDU command
By default upon power-up, the product is in ATD state. This mode is used to activate a card or
check its presence automatically.
In application tests whereby manual control is needed, for example switching the RF field off or
modulation control is required; it is possible to control using the APDU command.
The list of APDUs are available from NXP’S PR533 User Manual (page41).
Please follow the following steps to do get to the APDU command window:
a) Place a card on the reader.
b) Select “Connect”, then place the following set parameter command on the APDU
command window, press “SEND”. Response will be without error
APDU command
window
July 19,2012/v1.0
TR33CUT018
User Manual
Response will be
without error
The following are some APDU commands that are need for testing in EMC.
3.1
RF ON mode with no modulation
This is basically to set the set to manual mode and turn on the RF carier only(no
modulation) manually.
To set back to ATD mode, send the APDU command below:
FF E1 04 01 01 01
July 19,2012/v1.0
TR33CUT018
User Manual
3.2
RF field OFF
The APDU command to do this:
FF E1 04 01 01 00
PCBA TR33MUT014 PCB and Antenna Dimension overview
The pcba used in TR33CUT018 product is TR33MUE014 Ver 1.2 as shown below.
July 19,2012/v1.0
TR33CUT018
User Manual
TR33MUE014 Ver 1.2 PCBA and Antenna dimension
Regulatory information
July 19,2012/v1.0
TR33CUT018
User Manual
Regulatory Information
Federal Communication Commission Notice
FCC Identifier: ORK-TR33CUT018
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance to
this equipment would void the user’s authority to operate this device.
Note :
1. This module is intended for end device installation. The installer is still responsible for the FCC
compliance requirement of the end product, which integrates this module. The host end product must
also pass the FCC Part 15 unintentional emission testing requirement and be properly authorized per
FCC Part 15. The host end product must include a user manual that clearly defines operating
requirements and conditions that must be observed to ensure compliance with current FCC RF exposure
guidelines.
2. The built-in antenna is integrated to the module and no other antenna should be used.
3. This module must not be co-located or jointly operated with any other antenna or transmitter within
host.
4. A label should be attached to the host end product in a visible area with the following statement:
“Contains Transmitter Module FCC ID: ORK-TR33MUE013” or “Contains FCC ID: ORK-TR33MUE013”.
EC R&TTE directive:
We, hereby declare that the above named module is in conformity to all the essential requirements of
Directive 1999/5/EC. The Conformity Assessment procedure referred to Article 10 and detailed in Annex
[III] or [IV] of Directive 1999/5/EC has been followed with involvement of the following notified body:
TIMCO ENGINEERING, INC., P.O BOX 370, NEW BERRY, FLORIDA 32669.
Identification mark: 1177 (Notified Body number)
The technical documentation relevant to the above equipment is held at:
• Toppan Forms Co. Ltd, 1-7-3 Higashi Shimbashi, Minato-Ku, Tokyo 105-8311, Japan
July 19,2012/v1.0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Producer                        : PDF-XChange 3.60.0117 (Windows)
Create Date                     : 2013:01:31 19:49:02+08:00
Page Count                      : 9

EXIF Metadata provided by EXIF.tools