Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1232548 |
| Application ID | Ppobsb8rXBMPYKSvK6BmQg== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 1.81kB (22624 bits) |
| Date Submitted | 2010-01-25 00:00:00 |
| Date Available | 2010-01-25 00:00:00 |
| Creation Date | 2010-01-11 17:44:03 |
| Producing Software | Acrobat PDFWriter 5.0 for Windows NT |
| Document Lastmod | 2010-01-11 22:10:41 |
| Document Title | RTS1 module User Manual.doc |
| Document Creator | RTS1 module User Manual.doc - Microsoft Word |
| Document Author: | rungeth |
RTS24 User Manual The RTS24 module can be interfaced with our host boards through on of the multi-pin connectors. This is a standard 0.1” center header connector. The RTS24 module is only designed and authorized to operate in our own Toro Company Host devices. It will not be a commercially available module and the applicant will retain control over the final installation. In order to allow proper operation of the module, only four antenna configurations are available and limited by use of a reverse polarity SMA connector attached to the module. Two common antennas are shipped with the product with two optional antennas available through Toro to make sure it complies with one of the authorized options. The module connector pins are shown in the schematics and drawings and should be only connected to host equipment as designated and controlled by The Toro Company. The VCC input voltage must be <24VDC and all the digital signals comply with standard CMOS “1” and “0” requirements.. The RTS24 radio complies with 802.15.4 IEEE standard. The nominal frequency is 2.4Ghz operating on channel 25. The maximum peak power is less than 0 dBm using any bandwidth. The typical sensitivity is –108 dBm. Typical communication range is ~300 feet Installation Instructions 1. The module is ESD sensitive and should be handled accordingly. Make sure that a ground strip is used at all time. 2. Before connecting the module be sure that the connection pins adhere to the specs as set in the schematic; a. Ground pins are properly grounded. b. Power supply pin 1 should be connected to the power supply on exceeding 24VDC c. The rest of the pins are digital pins carrying data and signaling with “1” as 3.3 volts and 0 as “0”. They should adhere to CMOS type levels. 3. The RF portion of the module has a 3.0V regulation but the input voltage should be kept within 5% of 3.0 volts. 4. The hosting device must have a label that states “Contains FCC ID: OF7RTS24” besides other required FCC labels for that device. 5. The hosting device must have a label that states “Contains IC: 3575A-RTS24” besides other required IC labels for that device. 6. The antenna should not be modified and must not be co-located or operated in conjunction with any other antenna or transmitter. FCC/IC Statement The module itself must have a FCC Identifier “FCC ID: OF7RTS24”. ( IC:3575A-RTS24) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Additional radiated spurious emission evaluation for the additional host device may be required. Statement needed to be shown on End Product Since this module is installed inside the end product, the end product should be affixed a label on visible area showing this product contains a RF model, and also its FCC ID and IC ID. Important Note This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The Toro Company (module integrator and applicant) will not provide information to the end use regarding how to install or remove this RF module in the user manual of the end product which integrate this module. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Caution: The user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2010:01:11 17:44:03Z Modify Date : 2010:01:11 22:10:41-05:00 Page Count : 2 Creation Date : 2010:01:11 17:44:03Z Author : rungeth Producer : Acrobat PDFWriter 5.0 for Windows NT Mod Date : 2010:01:11 22:10:41-05:00 Metadata Date : 2010:01:11 22:10:41-05:00 Title : RTS1 module User Manual.doc Creator : rungethEXIF Metadata provided by EXIF.tools