Toshiba Hd S23 Owners Manual Regulatory Compliance

: Toshiba Toshiba-Hd-S23-Owners-Manual-129073 toshiba-hd-s23-owners-manual-129073 toshiba pdf

Open the PDF directly: View PDF .
Page Count: 40

Digital

High Definition Receiver

HD-S23 7

Introduction

11

Connections

OWNER'S MANUAL Menu Navigation 15

27

Quick Control

31

Appendices

©2003 Toshiba Corporation

1

Precautions

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

TO PREVENT ELECTRIC SHOCK, DO NOT OPEN THE COVER. REFER SERVICING

TO QUALIFIED PERSONNEL ONLY.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet,

even if the unit itself has been turned off.

NOTE

The rating label and the safety caution are on the rear of the unit.

Power cord cautions

 When plugging in or unplugging the power cord, hold it by the plug. Do not unplug it by pulling

on the cord.

 Do not touch the cord with wet hands as this could cause electrical shock or shorting

 Do not place furniture, etc, on top of the power cord.

 Do not tie up the power cord, or connect a different power cord.

 Route the power cord so that it is not stepped on, or tripped over.

 Using a damaged power cord could result in fire or electric shock. Inspect the power cord for

damage. If damaged, consult your nearest TOSHIBA service centre or have it replaced at a sales

outlet.

Welcome to the world of high definition picture and sound created by the TOSHIBA HD-S23 Set-Top

Box. In order to enjoy the many features this receiver has to offer, please read this owner’s manual

thoroughly before using.

Please record the serial number located on the back of the receiver. In the following spaces.

Serial No:

In order to continue to get the maximum performance from your receiver:

 Make sure that it is set up properly.

 Have it regularly inspected by qualified service personnel.

 Make sure that all family members learn to operate it properly.

In particular:

Prevent electric shock by making sure that children do not insert objects into the receiver’s holes or

slots.

Please do not use or place the receiver in the following environments.

1. Near heat sources.

 Places subject to direct sunlight.

 Near radiators or air ducts.

 On top of an amplifier

2. Dusty places

3. Places subject to vibration or shock

4. Near strong magnetic fields such as a speaker or a cassette deck.

5. Places subject to moisture such as a kitchen or bathroom.

2

6. Places without adequate air circulation.

 On top of a carpet or sofa.

 In a bookcase.

 Near materials such as curtains, etc.

7. Extremely hot or cold places

 The operating temperature range of this unit is 5℃ to 40℃

8. Do not place a flower vase or cloth on top of this unit.

Please pay attention to the following items when using this unit. Failure to do so may result in damage to the unit or

electric shock.

1. Connect the power plug to AC 100-240V 50/60Hz

2. Unplug the power cord from the receiver before connecting any other equipment, especially the TV antenna.

Connect all equipment to the receiver before plugging any power cords to the power source.

3. Be sure your TV antenna is not located near overhead power lines, or where it might fall into any power

lines. Also be careful to avoid touching any such power lines when installing the TV antenna.

4. Be sure that antenna is grounded to provide protection from lightning and build-up of static electricity.

5. Do not attempt to modify the unit.

6. If you hear a strange a sound or notice smoke coming from the unit, turn the power off immediately, unplug

the power cord, and consult with your local sales outlet.

7. Do not drop metal objects, paper or liquids into the unit through the ventilation openings, etc.. This may

result in damage. In the event something is dropped inside, turn the power off, unplug the power cord and

consult with your local sales outlet.

8. When transporting, do not vibrate or shake the unit. This may result in damager or faulty operation.

9. If a three-prong power plug is provided with receiver. Be sure it is used with a properly grounded

three-wise power socket.

10. Do not use insecticide sprays, etc, near the unit. Also, do not leave rubber or plastic objects in contact with

the unit for long periods of time. This may cause discolouring of this unit’s finish.

11. When transporting the unit, be sure to turn off the power and disconnect all cables.

12. When not using the unit for a long period of time (when on vacation, etc) unplug the power cord.

13. Keep the original packing that this unit came in and use it to re-pack the unit when moving or transporting.

14. Avoid overloading electrical outlets or extension cords, otherwise it could result in electric shock or fire.

MOISTURE CONDENSATION

Never operate this receiver immediately after moving it from a cold location to a warm location. In

this case, connect the power cables of the receiver to an AC outlet, to turn the power on and leave it

for TWO TO THREE hours without operating it.

Moisture condensation is most likely to occur in the following cases:

 When moved from a cold location to a warm location.

 In a room rapidly heated or in a place where the receiver is directly exposed to cool flow of air

from an air-conditioner or other electrical appliance.

 In a room with excessive dampness or high humidity.

3

Types of Power Plug

Australia 3-prong power plug imagine to be

paste here by Zinwell!

Power cord must be used in

Australia only

Singapore 3-prong power plug imagine to be

paste here by Zinwell!

Power cord must be used in

Singapore only

4

TABLE OF CONTENTS

TABLE OF CONTENTS

PRECAUTIONS.....................................................................................................................................................................2

TYPES OF POWER PLUG ..................................................................................................................................................4

TABLE OF CONTENTS .......................................................................................................................................................5

INTRODUCTION..................................................................................................................................................................7

FEATURES .........................................................................................................................................................................7

IDENTIFICATION OF CONTROLS..................................................................................................................................8

Front Panel.....................................................................................................................................................................8

Rear Panel ......................................................................................................................................................................8

REMOTE CONTROL ...............................................................................................................................................................9

Loading batteries..........................................................................................................................................................10

Operating with the remote control................................................................................................................................10

CONNECTIONS..................................................................................................................................................................11

CONNECTING TO AUDIO VIDEO DEVICES ..............................................................................................................12

CONNECTING TO SDTV (WITHOUT COMPONENT INPUTS)..................................................................................................13

CONNECTING TO SDTV (WITH COMPONENT INPUTS) AND VCR ........................................................................................13

CONNECTING TO HDTV .....................................................................................................................................................14

CONNECTING TO HDTV AND VCR.....................................................................................................................................14

MENU....................................................................................................................................................................................15

MENU MAP......................................................................................................................................................................16

INITIAL SETUP ...............................................................................................................................................................17

MAIN MENU....................................................................................................................................................................17

INSTALLATION...............................................................................................................................................................18

AUTO SCAN.................................................................................................................................................................18

QUICK SCAN...............................................................................................................................................................18

MANUAL SETUP .........................................................................................................................................................19

RESET DATA ................................................................................................................................................................19

PROGRAM .......................................................................................................................................................................20

ELECTRONIC PROGRAM GUIDE ................................................................................................................................20

SYSTEM ...........................................................................................................................................................................21

PASSWORD ..................................................................................................................................................................21

VIDEO SETUP .............................................................................................................................................................21

AUDIO SETUP.............................................................................................................................................................22

5

SOFTWARE UPDATE ..................................................................................................................................................22

TIME SETUP................................................................................................................................................................23

EDIT CHANNEL..............................................................................................................................................................24

FAV & LOCK ................................................................................................................................................................24

PARENTAL GUIDANCE (RATING) .............................................................................................................................24

PROFILE...........................................................................................................................................................................25

TRANSPARENCY..........................................................................................................................................................25

I-PLATE SETUP...........................................................................................................................................................25

INFORMATION............................................................................................................................................................26

QUICK CONTROL .............................................................................................................................................................27

I-PLATE (INFO) ...............................................................................................................................................................28

AUX IN (EXTERNAL VIDEO/AUDIO INPUT).......................................................................................................................29

PIP (PICTURE-IN-PICTURE).................................................................................................................................................29

TELETEXT / CLOSED CAPTION ..................................................................................................................................30

FAVOURITE CHANNEL LIST ........................................................................................................................................30

FREEZE ............................................................................................................................................................................30

A.RATIO ...........................................................................................................................................................................30

APPENDICES ......................................................................................................................................................................31

APPENDIX 1 DTV CHANNEL TABLE ....................................................................................................................32

APPENDIX 2 TROUBLESHOOTING .......................................................................................................................35

APPENDIX 3 PARENTAL GUIDANCE CODES......................................................................................................37

APPENDIX 4 GLOSSARY.........................................................................................................................................38

APPENDIX 5 TECHNICAL SPECIFICATIONS .......................................................................................................39

APPENDIX 6 ACCESSORIES ...................................................................................................................................40

6

INTRODUCTION

The HD-S23 Digital Terrestrial HDTV Receiver opens up to a new world of free-to-air terrestrial HDTV and SDTV

programmes. The receiver can receive channels from both VHF band and UHF band TV station’s signals. All the

major terrestrial free-to-air station numbers currently available in your area are listed in the on-screen menu. To

watch a channel, simply select the channel number and you will be accessing a wide range of high quality digital

programmes.

The receiver is fully MPEG 2 / DVB-T compliant, delivering High Definition crystal-sharp video and Dolby®

Digital sound. As it supports a channel frequency range of 50-860 MHz, it can be easily programmed for all the

channels within the VHF and UHF frequency bands. To find out the channel frequencies in your area, please contact

your local service provider.

Introduction

FEATURES

HD 1080i Capability

High Definition (HD) brings a wide-screen format to the home television as well as a sharper picture. This receiver

corresponds with 1080i signal input and it fully recreates high definition screen quality.

Dolby® Digital

Dolby® Digital is the surround sound technology used in theatres showing the latest movies, and is now available to

reproduce this realistic effect in the home. You can enjoy motion pictures and live concert TV programmes with this

dynamic realistic sound by connecting HD-S23 receiver to a 6-channel amplifier equipped with a Dolby® Digital

decoder.

Teletext/Fastext

PIP (Picture-in-Picture)

This feature gives you the ability to view 2 different channels at the same time. One program can be viewed on the

main screen while another is simultaneously displayed in a smaller viewing window, often positioned in one corner

of the screen. The basic PIP system requires you to use the tuner of an externally connected video component such

as a VCR as the source for the second signal.

AUX Input

Allows you to select video input between Antenna and DVD/VCR.

Still Picture Display

Allows you to take a snapshot of a video at a particular instant as a still picture.

Wide-screen Picture Format

Wide-screen is the term given to picture displays that have a wider aspect ratio than normal. For example, the aspect ratio for

conventional TVs is 4:3 and for wide-screen TVs is 16:9. This receiver supports broadcasts in both formats.

7

IDENTIFICATION OF CONTROLS

Front Panel

    

 LED Display

Four-digit channel number, time or video format

Two LEDs:

Green for power; Red for signal indication (OFF –signal captured, ON –no signal)

 MENU / ENTER (Please refer to pp. 17 for more details)

 EXIT / V.OUTPUT → OUT1 & OUT2 description (Zinwell)

 Direction Keys

 Power on / off

Rear Panel

        

 AC MAINS SUPPLY  (OUT1) Composite- VIDEO / L

/ R

100~240 VAC, 50/60 Hz For connection to TV monitor’s Video/L/R

inputs

 SERIAL PORT 

For connection to PC for software upgrade For connection to DVD or VCR Video/L/R

output

 DIGITAL AUDIO (OPTICAL)  RF OUT

For connection to an amplifier equipped For connection to analogue TV’s ANT. IN

with Dolby® Digital decoder

 (OUT2) Component – Y/Pb/Pr  ANT.IN

For connection to TV monitor’s For connection to UHF/VHF antenna

component video inputs

 S-VIDEO (OUT1)

For connection to TV monitor’s S-Video input

8



Remote Control

The buttons on the remote control are described as follows:

 Numeric Buttons For entering channel number or password

 POWER Switches the receiver between ON and STANDBY modes

 INFO Displays I-Plate providing information about the current

channel

 AUDIO Toggles between multi-lingual Audio soundtracks

 MENU Activates the On-Screen Menu

 LIST Displays the complete channel/program list

 FAV Displays the Favourite channel list

 Direction buttons To move through menus or submenus

 ENTER Selects the highlighted menu or submenu item

 CH+/CH- Provides channel up and down functions

 VOL+/VOL- Increases or decreases audio volume

 A.RATIO Adjusts the aspect ratio between 16:9 and 4:3

- Wide Vision: to display 16:9 program on 16:9 TV screen

to display 4:3 program on 4:3 TV screen

- Wideview Normal: to display 16:9 program on 4:3 TV

screen in letterbox

- Normal Vision: to display 16:9 program cropped on 4:3

TV screen

 PIP Shows the auxiliary input and multiple programs list in the

same DTV Network the receiver is tuned to and

allows displaying the second program on the TV screen

 AUX Selects between ANT.IN (DTV signal) and AUX (DVD or

VCR) inputs

 V. F or m at Toggles between 576i, 576p, 720p and 1080i video

formats through Y/Pb/Pr video connectors.

 Freeze To Freeze the picture on the main Screen.

 V.Output Switch between Composite (Out 1) and Component

(Out 2)

Introduction

9

Loading batteries

Operating with the remote control

1. Open the Cover

2. Insert batteries (AAA size)

Make sure to match the + and – on the batteries to the marks inside the battery compartment.

3. Close the cover.

Notes on batteries

Improper use of batteries may cause battery leakage and corrosion. To operate the remote control

correctly, follow the instructions below.

 Do not insert batteries into the remote control in the wrong direction.

 Do not charge, heat, open, or short-circuit the batteries. Do not throw batteries into a fire.

 Do not leave dead or exhausted batteries in the remote control.

 Do not use different types of batteries together, or mix old and new batteries.

 If you do not use the remote control for long period of time, remote the batteries to avoid

possible damage from battery corrosion.

 If the remote control does not function correctly or if the operating range becomes reduced,

replace all batteries with new ones.

 If battery leakage occurs, wipe the battery liquid from the battery compartment, then insert

new batteries.

Operating with the remote control

Point the remote control at the remote sensor and press the buttons.

Distance: About 7 m (23 feet) from the front of the remote sensor.

Angle: About 30°in each direction of the front of the remote sensor.

 Do not expose the remote sensor of the DVD player to a strong light source such as direct

sunlight or other illumination. If you do so, you may not be able to operate the DVD player

via the remote control.

Notes on the remote control

 Direct the remote control at the remote sensor of the DVD player.

 Do not drop or give the remote control a shock.

 Do not leave the remote control near an extremely hot or humid place.

 Do not spill water or put anything wet on the remote control.

 Do not open the remote control

10

11

UConnections

Read this chapter first to make all necessary preparations

• Connecting to Audio Video Devices

• Connecting to SDTV (without Component

Inputs)

• Connecting to SDTV (with Component Inputs)

and VCR

• Connecting to HDTV

• Connecting to HDTV and VCR

CONNECTING TO AUDIO VIDEO DEVICES

For the best video/audio quality, use the higher quality Y/Pb/Pr or S-Video cables if available. Always

remember to disconnect the receiver from the power source, when connecting or disconnecting the cable to

the UHF/VHF antenna.

Notes:

(a) If your TV supports 1080i / 720p / 576p / 576i video input formats, please use the receiver’s OUT2

video connectors. You may use the V.FORMAT button on the remote control to switch between four

video output formats 1080i/720p/576p/576i.

(b) If your TV supports 576i video input format, please use the receiver’s OUT1 connectors to connect to

your TV.

For more details on the various ways of connection, please refer to pp. XX.

Before connecting or disconnecting the antenna cable, turn off the antenna booster, if any.

12

Connecting to SDTV (without Component Inputs)

Connections

Connecting to SDTV (with Component Inputs) and VCR

13

Connecting to HDTV

Connecting to HDTV and VCR

14

15

UMenu

Functions in the Menu.

• Menu Map

• Initial Setup

• Main Menu

• Installation

- Auto Scan

- Quick Scan

- Manual Setup

- Reset Data

• Program

• Electronic Program Guide

• System

- Password

- Video Setup

- Audio Setup

- Software Update

- Time Setup

• Edit channel

- Fav. & Lock

- Parental Guidance (Rating)

• Profile

- Transparency

- I-Plate Setup

- Information

MENU MAP

MENU MAP

16

INITIAL SETUP

If your service provider or antenna installer has already installed your TV system to receive terrestrial TV

programmes, do not change any connections of those devices or installation settings unless it is absolutely necessary.

If your receiver has not been configured by your service provider or system installer, then it will not be set up for

any specific channel or frequency when powered on for the first time.

● Initial Screen –

The first time the receiver is powered on, it will

display a Country Selection menu.

● Use the arrow buttons “▲” and “▼” to highlight

your country of residence and press the “ENTER”

button to make your selection.

● If the Initial Screen does not appear, press the

“MENU” button for configuration.

Zinwell to-do:

Above is tentative description.

Actual procedure to be confirmed by Zinwell.

Also Zinwell should provide an updated

snapshot for country selection screen.

AUS SIN

Menu Navigation

MAIN MENU

There are two ways to enter the Main Menu when the receiver is powered on:

● On the remote control, press the “MENU” button.

● Alternatively, press “MENU” button on the front

panel.

Use the arrow buttons ▼▲ to navigate through the

menu, “ENTER” button to choose specific items, and

“EXIT” button to return to the main menu from

submenu or to leave the main menu.

17

INSTALLATION

On the main menu, select “INSTALLATION” and key-in your password to enter the Installation page.

Note: The default password is 0000. Please refer to pp. XX to change the password.

AUTO SCAN

The steps required to automatically program the receiver are outlined as below:

● Highlight “AUTO SCAN” and press the

“ENTER” button to start channel search.

● The receiver starts scanning from channel 2 to

channel 69. The status bar shows the progress

being made.

● Once the digital TV signal is scanned, the channel

number and program name will be shown.

NOTE: Auto scan process may take about 18 minutes to

complete.

QUICK SCAN

If you live in one of the cities listed on the Quick Scan menu, you may select your city and start scanning all

predefined digital TV channel signals..

● On the installation page, highlight “QUICK SCAN”

and press the “ENTER” button.

● Use the “▲” and “▼” buttons to highlight the city

you live in and press the “ENTER” button to start

scanning.

● For Australia, it will scan through five RF channels

including “Seven”, “Nine”, “Ten”, “ABC and “SBS”.

Note: The frequencies of these five channels are

preset in the receiver’s database. In the case

that the channel frequency is changed by the

local TV station or a new channel comes up

after July 2003 you have to scan these

channels using “MANUAL SETUP”.

18

MANUAL SETUP

● On the Installation page, highlight “MANUAL

SETUP” and press the “ENTER” button.

● Select channel number. Be sure you know the

channel number and its RF frequency. You may

refer to Digital TV channel table on Appendix 1.

● Press “▼” button to highlight “Frequency”,

“Bandwidth” and “Priority” to make sure the

parameters are correct, then press “▼” button to

highlight “Start Scan” and press the “ENTER”

button to start scanning.

Note:

(1) If scanning is successful, “Start Scan” will change to “Get Channel Success” and signal quality will be

shown. At this point you can press “EXIT” to leave “MANUAL SETUP” or continue scanning other

channels.

(2) If scanning is unsuccessful, “Start Scan” will change to “Time out error”. At this point you can rescan the

signal or refer to the signal level bar “LVL” and bit error rate counter “BER” for aligning the direction of

the antenna to get the signal. Please refer to your Antenna Installer if problem persists.

(3) For Australia, the bandwidth should be 7MHz while for Singapore the bandwidth should be 8MHz.

Menu Navigation

RESET DATA

Zinwell to-do:

Add RESET DATA description here!

19

PROGRAM

● On the main menu, select “PROGRAM” to enter

the program list.

● Use the “▲” and “▼” buttons to browse through the

channel numbers and names

Note: Alternatively, when you are watching a Digital TV

channel (without any menu on screen), you can

press the “LIST” button on the remote control

twice to call up the program list.

ELECTRONIC PROGRAM GUIDE

● To call out the program guide of the specific

channel, highlight the channel from the

program list and press the “ENTER” button.

● Alternatively, you may press the “INFO” button on

the remote control twice to call up the program guide.

● Use “◄” and “►” buttons for details on NOW and

NEXT event, and “▲” and “▼” buttons for scrolling

an event table that consists more than 1 page.

 The first row shows channel name, show times and

parental rating. The second row shows program name

and third row shows program genre.

EPG’s OSD need to change to have three rows on the top of OSD.

20

SYSTEM

● On the main menu, select “SYSTEM”.

● Use the “▲” and “▼” buttons to highlight the

options

- PASSWORD

- VIDEO SETUP

- AUDIO SETUP

- S/W UPDATE

- TIME SETUP

PASSWORD

● Highlight “PASSWORD” and press the “ENTER”

button. When prompted, enter your current password.

● You will then be prompted to enter the New

Password.

● Enter the new password again to reconfirm.

Note: The default password is 0000.

Menu Navigation

VIDEO SETUP

● Highlight “VIDEO SETUP” and press the

“ENTER” button.

● Use the “◄” and “►” buttons to switch between

“4:3” and “16:9” picture formats.

21

AUDIO SETUP

● Highlight “AUDIO SETUP” and press the “ENTER”

button.

● Use the “▲” and “▼” buttons to switch between

“PCM” and “Dolby® Digital” .

Note: The digital audio output will automatically output

in PCM format whenever switching to a channel

without Dolby® Digital sound track.

Digital output: PCM and Dolby digital

(add description here)

Note: You need to connect to an amplifier with AC-3 decoding capability via Digital Audio (SPDIF) Output when

Dolby Digital option is selected. Otherwise, you may encounter softer audio from TV output.

Audio Format English (MPEG1) & English (Dolby)

SOFTWARE UPDATE

This option in System page updates the software in the receiver. However, before you proceed to update the software,

please consult your local dealer first and make sure you know how to operate Microsoft Windows HyperTerminal on

your computer.

● Highlight “S/W UPDATE” and press the “ENTER”

button.

● Use the “◄” and “►” buttons to highlight between

“YES” and “NO”.

● Before you select “YES”, please follow the steps

outlined below to configure your PC first:

(a) Connect PC to your HD-S23 receiver with a

cross-over RS232 cable (cable for null modem)

(b) On the PC side:

- Launch the Windows HyperTerminal application.

- Name the connection.

- Select the correct COM port – usually COM1.

- Use the following COM port settings:

baud rate: 115200

data: 8

parity: none

stop bit: 1

flow control: none

- Select HyperTerminal’s basic function “Transfer”.

- Select “Send File”.

- Browse to select the updated software file.

- Transfer protocol: “1K Xmodem”

DON’T click on the “Send” button at this time

yet.

22

● Now that your PC has been properly configured, you

can highlight “YES” on the TV screen and press the

“ENTER” button on the remote control.

- To be continued on the next page –

● After selecting “YES”, you will see the current software

version and its size on the TV screen. Make sure this

software version is different from the version of the new

software file stored on your PC. Select “YES” again to

proceed with the download.

● Now click on the “Send” button on your PC

Hyperterminal to start uploading the new software.

● On the TV screen, you will see the window with a status

bar indicating the download progress

● When download is completed, the receiver will reboot

automatically.

● After the receiver is booted up, you will see a message

window informing you that the receiver’s database is

empty.

● Press the “MENU” button on the remote control, select

“PROFILE” then select “INFORMATION” to confirm the

current software is indeed changed to the new one. You

can then proceed to scan digital TV channels by following

instructions on pp. XX and XX.

Menu Navigation

TIME SETUP

● Highlight “ TIME SETUP” and press the

“ENTER” button.

● Use the “◄” and “►” buttons to select the local

time zone you are located in.

23

EDIT CHANNEL

Zinwell to-do:

Add the screen snapshot for EDIT CHANNEL here.

● On the main menu, select “EDIT CHANNEL”.

● Use the “▲” and “▼” buttons to highlight the

options

- FAV & LOCK

- PARENTAL RATE

Add two selections here.

FAV & LOCK

● Highlight “FAV & LOCK” and press the “ENTER”

button.

● Use the “▲” and “▼” buttons to select the channel,

use the “◄” and “►” buttons to select “LOCK” or

“FAV”.

● Highlight “LOCK” and press the “ENTER” button to

lock the selected channel.

● Highlight “FAV” and press the “ENTER” button to

add the selected channel into the favourite list.

PARENTAL GUIDANCE (RATING)

● On the “EDIT CHANNEL” page, highlight

“PARENTAL RATING” and press the “ENTER”

button to block programs.

● Use the “▲” and “▼” buttons to select the Rating

and press the “EXIT” button to confirm the setting.

● When DTV programs broadcasted are accompanied by

the ratings, the programs will be blocked based on

your setting. You have to enter PASSWORD to

resume watching the program.

● Please refer to Appendix 3 for details.

24

PROFILE

● On the main menu, select “PROFILE”.

● Use the “▲” and “▼” buttons to highlight the options

- TRANSPARENCY

- I-PLATE SETUP

- INFORMATION

TRANSPARENCY

● Highlight “TRANSPARENCY” and press the

“ENTER” button.

● Use the “◄” and “►” buttons to change the degree

of transparency of the on-screen-display.

Menu Navigation

I-PLATE SETUP

● Highlight “I-PLATE SETUP” and press the “ENTER”

button.

● Use the “▲” and “▼” buttons to highlight “Fading

Mode”, “Display Time” and “Time Format”.

● Use the “◄” and “►”buttons to change the values of

the highlighted options.

25

INFORMATION

● Highlight “INFORMATION” and press the “ENTER”

button to check hardware and software versions.

26

27

UQuick Control

Simple use of a single button enables access to some functions directly

• I-Plate (Info)

• AUX In (External Video/Audio Input)

• PIP (Picture-in-Picture)

• Teletext / Closed Caption

• Favorite Channel List

• Freeze

• A.Ratio

I-PLATE (INFO)

● When watching DTV channels (without any menu on

the screen) , press the “INFO” button.

● I-PLATE will pop up with the following information:

- Current Channel Number

- Network Name

- Program Name

- Audio System (Dolby® Digital or MPEG)

- Teletext

- Current Local Time

- Date and Month

- Parental Guidance

● When I-PLATE is still on the TV screen, you can

press the “INFO” button again to call up the extended

program information (also known as electronic

program guide) of the current TV channel.

● Please refer to pp. XX for details on electronic

program guide.

28

AUX IN (External Video/Audio Input)

● Press the “AUX” button on the remote control to

select the following options:

- OFF-AIR

- AUX

● Use the “▲” and “▼” buttons to highlight the options

and press the “ENTER” button to select.

User can change to any other format by pressing the

“V.Format” button. (Please refer to Pg 9). This feature is

possible only through the use of “OUT2” connector

(Y/Pb/Pr).

Quick Control

PIP (Picture-in-picture)

● When watching a TV program (not in the main menu),

press the “PIP” button on the remote control to

bring up the PIP menu with a list of different

programs .

● Use the “▲” and “▼” buttons to browse through the

program list.

● Highlight a program and press the “ENTER” button to

show “picture-in-picture” – two programs playing on

the TV screen at the same time.

● To close PIP window, press the “PIP” button and

select “PIP OFF”.

N

OTE: When playing VCR movie in PIP window through

AUX IN connection, you may encounter poor picture

quality if old video tape is used.

29

TELETEXT / CLOSED CAPTION

● When I-PLATE indicates the presence of Teletext,

you can press the “TTX/CC” button on the remote

control to display it on the TV screen.

 To show the close caption on TV screen, press

“TTX/CC” button and go to page “801”.

Note: Close caption will be disabled when new OSD was

displayed on screen.

FAVOURITE CHANNEL LIST

● Press the “FAV” button on the remote control to

call up the Favourite List.

● Use the “▲” and “▼” buttons to browse through the

favourite list and highlight the program you want to

watch.

● Press the “ENTER” button to confirm your selection.

FREEZE

Zinwell to add description here for FREEZE button!

A.RATIO

Zinwell to add description here for A.RATIO button!

30

31

UAppendices

• DTV Channel Table

• Troubleshooting

• Parental Guidance Codes

• Glossary

• Technical Specifications

• Accessories

APPENDIX 1 DTV CHANNEL TABLE

The following is a list of DTV channels available in your area. You can use it for “MANUAL SETUP”: On the

“MANUAL SETUP” page, select the VHF or UHF channel number and input the Middle Frequency based on

“KHz”. For instance, if you are in Sydney and want to manually scan “Digital 7”, enter “MANUAL SETUP” page,

select “Channel 6” and make sure the Frequency is “177500” KHz, then start scanning. Please refer to “MANUAL

SETUP” on pp. XX for details.

For Australia:

City Identifier Channel & Middle

Frequency

Transmitter Location Start Date

Adelaide Digital 7 VHF 6 - 177.5MHz Mt Lofty 1/1/2001

Digital 9 VHF 8 - 191.625MHz Main Transmitter - Mt Lofty 1/1/2001

Digital 10 VHF 11 - 219.5MHz Main Transmitter - Mt Lofty 1/1/2001

Digital ABC VHF 12 - 226.5MHz Main Transmitter - Crafers 1/1/2001

Digital SBS UHF 28- 564.5MHz Main Transmitter - Mt Lofty 1/1/2001

Brisbane Digital 7 VHF 6 - 177.5MHz Main Transmitter - Mt Coot-tha 1/1/2001

Digital 9 VHF 8 - 191.625MHz Main Transmitter - Mt Coot-tha 1/1/2001

Digital 10 VHF 11 - 219.5MHz Main Transmitter - Mt Coot-tha 1/1/2001

Digital ABC VHF 12 - 226.5MHz Main Transmitter - Mt Coot-tha 1/1/2001

Digital SBS UHF 36 - 585.5MHz Main Transmitter - Mt Coot-tha 1/1/2001

Melbourne Digital 7 VHF 6 - 177.5MHz Main Transmitter - Mt Dandenong 1/1/2001

Digital 9 VHF 8 - 191.625MHz Main Transmitter - Mt Dandenong 1/1/2001

Digital 10 VHF 11 - 219.5MHz Main Transmitter - Mt Dandenong 1/1/2001

Digital ABC VHF 12 - 226.5MHz Main Transmitter - Mt Dandenong 1/1/2001

Digital SBS UHF 29 - 536.625MHz Main Transmitter - Mt Dandenong 1/1/2001

Perth Digital 7 VHF 6 - 177.5MHz Main Transmitter - Carmel 1/1/2001

Digital 9 VHF 8 - 191.625MHz Main Transmitter - Carmel 1/1/2001

Digital 10 VHF 11 - 219.5MHz Main Transmitter - Carmel 1/1/2001

Digital ABC VHF 12 - 226.5MHz Main Transmitter - Carmel 1/1/2001

Digital SBS UHF 29 - 536.625MHz Main Transmitter - Bickley 1/1/2001

Sydney Digital 7 VHF 6 - 177.5MHz Main Transmitter Artarmon 1/1/2001

Digital 9 VHF 8 - 191.625MHz Main Transmitter Artarmon 1/1/2001

Digital 10 VHF 11 - 219.5MHz Main Transmitter Artarmon 1/1/2001

Digital ABC VHF 12 - 226.5MHz Main Transmitter Artarmon 1/1/2001

Digital SBS UHF 34 - 571.5MHz Main Transmitter Gore Hill 1/1/2001

32

City Identifier Channel & Middle

Frequency

Transmitter Location Start Date

Batchelor QQQ -51 UHF 50 - 683.5MHz

SBS -54 UHF 53 - 704.5MHz

ABD -69 UHF 56 - 725.5MHz

NTD -60 UHF 59 - 746.5MHz

TND -63 UHF 62 – 767.5MHz

IMP -66 UHF 65 - 788.5MHz

Canberra CTC -7 VHF 6 - 177.5MHz Telstra Tower Black Mountain 6/30/2002

ABC -9 VHF 9A - 205.5MHz Telstra Tower Black Mountain 6/30/2002

WIN -31 VHF 11 - 219.5MHz Telstra Tower Black Mountain 6/30/2002

CBN -34 VHF 12 -226.5MHz Telstra Tower Black Mountain 6/30/2002

SBS -28 UHF 30 -613.5MHz

Telstra Tower Black Mountain 6/30/2002

Darwin SBS -28 UHF 29 - 536.5MHz Deloraine Rd 6/30/2002

ABC -6 UHF 30 - 543.5MHz Deloraine Rd 6/30/2002

NTD -8 UHF 31 - 550.5MHz Deloraine Rd 6/30/2002

TND -34 UHF 32 -557.5MHz Deloraine Rd 6/30/2002

Newcastle NBN -3 UHF 36 - 585.5MHz Mt Sugarloaf 6/30/2001

NEN -54 UHF 53 - 704.5MHz Broadcast Site Mt Sugarloaf 6/30/2001

NRN -57 UHF 51 - 690.5MHz Broadcast Site Mt Sugarloaf 6/30/2001

ABHN

-5A/4B

UHF 37 - 592.5MHz Mt Sugarloaf 6/30/2001

SBS -45 UHF 38 - 599.5MHz Mt Sugarloaf 6/30/2001

Wollongong WIN -59 UHF 36 - 585.5MHz WIN Tower Knights Hill TBA

CTC -62 UHF 37 - 592.5MHz NTL Tower Knights Hill TBA

CBN -65 UHF 38 - 599.5MHz WIN Tower Knights Hill 6/30/2002

ABWN -56 UHF 51 - 690.5MHz NTL Tower Knights Hill 6/30/2002

SBS -53 UHF 54 - 711.5MHz NTL Tower Knights Hill 6/30/2002

Appendices

33

For Singapore:

City Identifier Channel & Middle

Frequency

Transmitter Location Start Date

Singapore TV Mobile VHF 602MHz Singapore 3/1/2001

Note:

(a) On the Channel Number Display of receiver’s front panel you will find the logical channel number different

from VHF/UHF channel number shown in the column “Channel & Middle Frequency” of this table.

(b) If you have trouble getting DTV channel’s signal, please contact your local antenna installer for help.

(c) The channel table in this manual may not be up-to-date. To get the latest channel table, please contact your local

dealer.

34

APPENDIX 2 TROUBLESHOOTING

Problem Solution

(1) The receiver front panel power indicator

doesn't light up, and no message on the

front panel

(a) Check the AC mains supply and make sure the power plug is

well plugged into a stable power outlet

(b) Press the “Power” button on the front panel to see if the LED

display is on.

(c) Press the “Power” button on the remote control to see if the LED

display is on.

(2) Message is shown on the front panel but

no picture on TV screen

(a) Make sure the connection between the receiver and TV matches the

mode your TV should be set to. For instance, if you use a RCA cable

you may choose external video input mode in TV.

(b) Check the brightness level of your TV.

Z

inwell to-do:

Add OUT1/OUT2 descriptions here.

(3) Poor picture quality (a) Check the antenna and make sure it is aligned to the correct

direction. Use the receiver's "MANUAL SETUP" page to check the

signal's BER and RF Level when aligning the antenna.

(b) If you use any kind of amplifier to boost the signal level, please

check whether it works well, and ask help from the antenna

installer.

(4) No sound (a) Check the receiver and your TV's volume are properly set and not in

“Mute" mode.

(b) Check the audio connectors are correctly and firmly connected.

(c) Make sure the receiver is switched to the correct Audio mode:

Dolby® Digital or PCM.

(d) Rescan this channel by using "MANUAL SETUP".

(e) Switch to other channels for confirmation on audio.

(5) No picture (a) Check the video cables are correctly and firmly connected.

(b) Rescan this channel by using "MANUAL SETUP".

(c) Switch to other channels for confirmation on video.

(6) Not all channels are available after using

“AUTO SCAN” when installing the

receiver for the first time

Try "MANUAL SETUP" to scan these missing channels.

This problem is caused by unexpected frequency offset, for instance,

in Sunshine Coast Australia, channels 47 and 65 are transmitted on

662.625 and 788.625 MHz by 125KHz offset to the legitimate

frequencies 662.5 and 788.5 MHz. HD-S23 can receive them by “AUTO

SCAN” most of the times, but we suggest that you use “MANAL

SETUP” when installing the receiver for the first time. Once the signal is

picked up by the receiver, all the transmission parameters will be stored

in the receiver's memory.

(7)

N

ot all channels are available after using

“QUICK SCAN”

(a) Try "AUTO SCAN" to scan all the channels.

(b) If you still cannot get some channels please use “MANUAL

SETUP” to scan them one by one.

(8) Cannot lock signal by using “MANUAL

SETUP”

(a) Check the frequency you entered is exactly the centre frequency of

the wanted channel.

(b) Please refer to solutions in item (3) on pp. XX.

(9) No Teletext Make sure the channel you are watching carries Teletext information

from I-PLATE.

(10) Cannot receive channels after moving

the receiver between cities (for instance

from Melbourne to Sydney)

Please refer to pp. XX for reinstallation.

(11) RCU button pressed not responding. Replace remote control unit batteries.

Appendices

35

APPENDIX 2 TROUBLESHOOTING (CONTINUED)

* On Screen Message

Message Solution

(1) Bad Signal

(a) Check the antenna is connected correctly and firmly to the tuner input

(ANT IN) of the receiver.

(b) Refer to solutions in Item (3) on pp. XX.

(2) Non Support HD Format The HDTV digital channel cannot be shown on the small PIP window.

(3) Weak Signal

Make sure antenna or signal input cable is connected correctly.

(4) Database is Empty No channel data available in the box.

Please refer to pp. XX for reinstallation.

(5) Program is Under Guard Please input the correct password or change lock setting in menu to view the

program.

(6) Program is Locked by Guard Rate Please input the correct password or change parental-rate (refer to pp. Error!

Bookmark not defined.) to view the program.

(7) Program Rate is over Guard Rate [xxx] Please input the correct password or change parental-rate (refer to pp. 24) to

view the program.

(8) Incorrect Password Please input the correct password.

36

APPENDIX 3 PARENTAL GUIDANCE CODES

Appendices

37

APPENDIX 4 GLOSSARY

* Aspect Ratio: It is the ratio of the width of the screen to the height. The two relevant digital TV formats are

16:9 (widescreen) or 4:3 (the traditional screen ratio). 16:9 is more ergonomically suitable for the human eye.

* Bandwidth: Frequency range allows for carrying a certain radio signal. The speed of data transmission

depends on the available bandwidth of the transmission channel.

* Coaxial Cable: A type of cable used to transmit high frequency signals e.g. from the VHF/UHF antenna to

the terrestrial Digital TV receiver.

* Composite Video: There are three elements of the video system: First - the " active video" which means the

picture to be displayed on the screen and its associated colors. Second - the " sync" decides where to place

each pixel on the screen. Third - the " blanking" tells the display when to turn off the electron beam so no

retrace across the screen. These three elements combined together is called " composite video" when

connecting to a display through connectors.

* Dolby® Digital: Dolby® Digital is a method of transmitting and storing multi-channel soundtracks via

newer digital media such as DVD, digital cable, digital broadcast TV (DTV), and satellite transmissions.

* DVB: Abbreviation for "Digital Video Broadcasting". An international organization created in October 1993,

whose primary objective is to achieve a common framework for all technical platforms of digital broadcasting

systems including DVB-C (cable), DVB-S (satellite), DVB-T (terrestrial), DVB-MC (MMDS), DVB-CS(SMATV).

* EPG: Abbreviation for "Electronic Program Guide". A software that enable viewers to navigate through the

large number of channels offered by digital TV broadcaster and select the desired services.

* Frequency: The property of a signal which is measured in cycles per second(=Hertz).

* Letterbox : The picture with aspect ratio 16:9 in a 4:3 TV screen with blank lines on top and bottom. It is the

means to watch a wide screen TV program on a 4:3 TV screen.

* Megahertz (MHz): Millions of cycles per second, which describes frequencies of radio wave or electric current.

* OSD: Abbreviation of "On Screen Display", used in digital set top box. OSD is comprised of a main menu and

many sub-menus with lots of options of functions inside.

* PAL: Stands for "Phase Alternating Line", the European video standard which has the image format of 4 by 3,

625 horizontal lines, 50 Hz and a total 8 MHz of video channel width.

* PID : Stands for "Packet Identifier". It is a code used for identifying video, audio PCR and other elements that

form a particular service in the transport stream.

* RF Channel: Radiated Frequency Channel, for instance channel 28 for SBS Network in analog TV transmission.

However in digital TV, one RF channel may carry 4 to 6 sub-channels like SBS HD, SBS Digital.

* S-Video (also called Y/C): The standard for the way a video signal is carried on the cable. Y represents

brightness and C represents color. S-Video cables have separate wires for the color and brightness so it offers a

better picture quality than the composite video.

* VHF: Stands for "Very High Frequency", starts from 30 to 300 MHz corresponding to channels 2-12, including

Bands I, II and III.

* UHF: Stands for "Ultra High Frequency", starts from 300 to 3000 MHz corresponding to channels 13-69,

including Bands IV and V.

* Y/Pb/Pr: Component Video Output. It is better than S-Video and Composite Video output in terms of picture quality.

Y/Pb/Pr is the standard HDTV connector.

38

APPENDIX 5 TECHNICAL SPECIFICATIONS

System

Compliant Standard DVB-T

Video Decoding MP @ ML & MP @ HL

Audio Decoding Dolby® Digital, MPEG (I & II)

Audio Sampling Rate 32, 44.1, 48 KHz

Terrestrial Tuner / Demodulator

Frequency 51~858 MHz

Loop Through 51~858 MHz

Bandwidth 6, 7, 8 MHz

Demodulator COFDM

FFT Mode 2K, 8K

Constellation QPSK, 16QAM, 64 QAM

Guard Interval 1/4, 1/8, 1/16, 1/32

Inner Coding Rate 1/2, 2/3, 3/4, 5/6, 7/8

Video Output

Format 1920 × 1080i, 1280 × 720p, 720 × 576p, PAL: 720 × 576i

Aspect Ratio 4:3, 16:9

Video Input

Format Composite Video

Digital Audio Output

Mode Decompressed PCM, Compressed Dolby Digital

Audio Input

Format Stereo

Front Panel

IR Receiver Yes

Function Control 7 Keys

Channel Display 4 Digits / 7-segment display

Rear Panel

Tuner Input 1 × IEC-Female

Video Input Port 1 × RCA

Stereo Audio Input Port 2 × RCA

S-Video Output Port 1

Video Output Port 1 × RCA

Y/Pb/Pr Video Output Port 3 × RCA

Stereo Audio Output Port 2 × RCA

Digital Audio Output Port 1 × S/PDIF Optical

Power Supply

Input Voltage 100~240 VAC, 50/60 Hz

Consumption (max.) 30 W

Dimension

Size (W × D × H) 430 × 80 × 290 mm

Weight 3.5 Kg (Unpacked)

Environmental Data

Operating Temperature 5°~ 40°C

Storage Temperature -40°~ 65°C

Appendices

*Specifications are subject to change without notice.

P/N:

39

APPENDIX 6 ACCESSORIES

• Remote Control (CT-90175)

• Audio/Video cable with RCA jacks

• Component Video cable (Y/Pb/Pr)

• Power cord (Singapore/Australia)

• Two AAA batteries

40