Toshiba Hdd2188 Mk8025Gas Users Manual May 10, 2000
2014-12-13
: Toshiba Toshiba-Hdd2188-Mk8025Gas-Users-Manual-128351 toshiba-hdd2188-mk8025gas-users-manual-128351 toshiba pdf
Open the PDF directly: View PDF 
.
Page Count: 11
| Download | |
| Open PDF In Browser | View PDF |
TOSHIBA AMERICA INFORMATION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA MK8025GAS (HDD2188) 2.5-INCH HARD DISK DRIVE USER MANUAL Rev 02 11/2006 CONTENTS Introduction..............................................................................1 Setup ........................................................................................2 Using the HDD .........................................................................4 Troubleshooting.......................................................................5 Specifications ..........................................................................6 Drive Connectors.....................................................................8 INTRODUCTION - MK8025GAS (HDD2188) General Features • 2.5" sized drive • 80 Gigabytes* • 9.5mm High • Fluid Dynamic Bearing (FDB) Motor • 12ms Average Seek Time • ATA-2,3,4,5,6 Interface • Supports high transfer rates of 100 MB/sec • 8MB Buffer • Rotational speed of 4,200rpm • MTTF 300,000 Hours *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. 1 SETUP – MK8025GAS (HDD2188) Caution: Your Hard Disk Drive is a precision device and even a small drop onto any surface can cause damage. Electronstatic discharge can also damage the drive. You should ground yourself prior to handling the drive. Master/Slave Settings Your Toshiba Hard Disk Drive can be configured as either a "Master" or "Slave" unit. Master configuration is used for all single drive applications, and master or slave configuration (only one of each per port) is used for two drive applications. Use the information in the following table before setting drive as Master or Slave. Master configuration is obtained by setting jumpers A, B, C & D open (no jumper present). Slave configuration is obtained by setting jumpers C-D. When B-D jumper is installed, the drive is configured as cable select. If pin 28 = Low, the drive is "Master", if pin 28 - High, the drive is "Slave". Figure 1.HDD Jumper Locations JUMPER No Jumper 2 P28 DRIVE - Master Drive C-D Jumper - Slave Drive B-D Jumper LOW Master Drive B-D Jumper HIGH Slave Drive A-B Jumper - Slave Drive A-C Jumper - Prohibit Installation Notes The drive should be mounted carefully on the surface of 0.1mm or less flatness to avoid excessive distortion. In order to prevent short-circuit under any circumstances, a space of 0.5mm or more should be kept under the PCB. Space should be kept around the drive to avoid any contact with other parts, which may occur due to shock or vibration. The temperature of the top cover and the base must always be kept under 60C to maintain the required reliability. Be sure not to cover the breathing hole to keep the pressure inside the drive at a certain level Do not apply any force to the top cover, except the screw areas on top cover. Maximum force to the specified area is 2N. The drive contains several parts which may be easily damaged by ESD (Electric Static Discharge). Avoid touching the interface connector pins and the surface of PCB. Be sure to use ESD proof wrist strap when handling drive. The four mounting screws should be tightened equally with 0.3N-m (3kgf-cm) torque. The depth should be 3.0mm minimum and 3.5mm maximum. Placing Hard Drive inside your Computer • • • • • • • Determine mounting configuration (the drive can be mounted in either a horizontal or vertical orientation) Configure drive for system application. Configure the adapter board for the specific system application (if required). Install adapter board into an unused PC/AT 16 bit slot (if required). Install the I/F cable to the system's 44 pin connector port or adapter board. Ensure pin 1 is oriented correctly, (pin 1 on the cable is usually identified by a red or blue strip.) Set correct drive type in system CMOS Refer to applicable manuals for software installation instructions. Important Note: Disconnect power from your computer system before beginning installation. Figure 2.HDD Mounting Holes 3 USING THE HARD DISK DRIVE – MK8025GAS (HDD2188) Backing up Data Files To avoid data loss, regularly back up the data files on the hard disk drive. 4 TROUBLESHOOTING – MK8025GAS (HDD2188) Problem My system is not able to recognize all available capacity on my Hard Disk Drive. What do I need to do to utilize the complete hard drive? How do I install my 2.5" Toshiba Hard Drive into my desktop or tower system? 5 Solution There are some systems that are unable to recognize the new larger Hard Drives on the market. 3rd party software is available that breaks the "capacity barrier". Some suggestions are EZ Drive by Micro House and Disk Manager DiskGo by Ontrack. Check with your local computer/software supplier for availability or contact the software manufacturer. You will need a HDD mounting kit in order to install a Toshiba 2.5" drive into your desktop or tower system. Contact your local computer supplier for kit availability. SPECIFICATIONS –MK8025GAS (HDD2188) General Model Interface MK8025GAS (HDD2188) ATA-2/3/4/5/6 Functionality Formatted Capacity 80.012GB* Rotational Speed 4200rpm Avg. Rotational Latency 7.14/ms Spin-up Time 4sec (typical) Buffer 8MB Seek Time (Average) 12 Internal Transfer Rate 175.0 ~ 341.7 Mbits/sec (max) Host Transfer Rate 100Mbytes/sec *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. Internal Drive Characteristics Number of Disks Number of Read/Write Heads Track Density (TPI) User Data Cylinders Logical Cylinders Logical Heads Logical Sectors/track Bytes per Sector Logical Blocks (LBA) 2 4 88.1k 54,000 16,383 16 63 512 156,301,488 Reliability Preventative maintenance Nonrecoverable read errors None 1 error per 1013 bits read Electrical Voltage 5V 5% Power Consumption Start Seek Read/Write Sleep Energy Consumption Efficiency 4.7W typ 2.6W typ 2.3W typ 0.1W typ 0.018W/GB avg Shock Operating Non-Operating 1,862m/s2 (190G)(2msec) 7,840m/s2 (800G)(1msec) 6 Physical Height Width Depth Weight 0.37" (9.5mm) 2.75" (69.85mm) 3.94" (100mm) 3.46oz (99g) typ Regulatory The drive satisfies the following standards: Underwriters Laboratories (UL) 1950 Canadian Standard Association (CSA) C22.2 No.220 No. 950 TUV Rheinland EN 60 950 EMC - EN50081-1 EN55022: 1988 Class B EN60555-2: 1987+ A1 EN60555-3: 77A (Co) 38 EMC - EN50082-1 IEC 801-2: 1991 EIC 801-3: 1994 IEC 801-4: 1988 7 DRIVE CONNECTORS –MK8025GAS (HDD2188) Figure 1.MK8025GAS HDD Rear View - Connectors Interface Connector Drive Side Connector Recommended Host Side Connector Board Cable Yamaichi GAP050K11617 or equivalent Straight type: Berg 86455-044 86456-044 or equivalent Berg 89361-044 or equivalent Recommended Cable Characteristics Standard diameter Characteristics impedance Max Length Capacitance * cable is not included with drive 8 0.32mm (28AWG) 100 - 132ohm 0.46mm (max) 35pF (max) Interface Pin Assignment DRIVE INTERFACE SIGNALS PIN SIGNAL PIN SIGNAL 1 RESET 2 GROUND 3 DD 7 4 DD 8 5 DD 6 6 DD 9 7 DD 5 8 DD 10 9 DD 4 10 DD 11 11 DD 3 12 DD 12 13 DD 2 14 DD 13 15 DD 1 16 DD 14 17 DD 0 18 DD 15 19 GROUND 20 KEY 21 DMARQ 22 GROUND 23 DIOW/STOP 24 GROUND 25 DIOR/ -DMARDY HSTROBE 26 GROUND 27 IORDY/ -DMARDY/DSTROBE 28 CSEL 29 DMACK 30 GROUND 31 INTRQ 32 IOCS16 33 DA1 34 PDIAG 35 DA0 36 DA 2 37 CS0 38 CS1 39 DASP 40 GROUND 41 +5V (LOGIC) 42 +5V (MOTOR) 43 GROUND 44 RESERVED Note: Symbol () in front of signal indicates negative logic. 9
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Tag Email Subject : SDD press releases for CES - Jan. 06. 2005 Tag Author Email Display Name : Sims, David Tag Author Email : dsims@golinharris.com Tag Ad Hoc Review Cycle ID : 669882224 Company : TOSHIBA Source Modified : D:20061116190003 Create Date : 2006:11:16 13:09:41-08:00 Creator Tool : Acrobat PDFMaker 7.0.7 for Word Modify Date : 2006:11:16 13:09:55-08:00 Metadata Date : 2006:11:16 13:09:55-08:00 Document ID : uuid:2f20e66f-ae40-4acb-991c-96cfaba6bffe Instance ID : uuid:cb373119-dffa-4591-b0a9-b5b7ff0a8b73 Version ID : 8 Format : application/pdf Title : May 10, 2000 Creator : lmimbs Subject : Headline : Page Count : 11 Page Layout : OneColumn Author : lmimbsEXIF Metadata provided by EXIF.tools