Touchtronics M130 Keyless Start RFID Reader User Manual Layout 1
Touchtronics Inc Keyless Start RFID Reader Layout 1
Exhibit D Users Manual per 2 1033 b3
O
OP
PE
ER
RA
AT
TI
IN
NG
G I
IN
NS
ST
TR
RU
UC
CT
TI
IO
ON
NS
S
K
KE
EY
YL
LE
ES
SS
S E
EN
NT
TR
RY
Y /
/ S
ST
TA
AR
RT
T /
/ S
SE
EC
CU
UR
RI
IT
TY
YS
SY
YS
ST
TE
EM
M
KEYLESS TRUCK ENTRY -
WRISTBAND KEY
Swipe the area 4”-6” in
front of the antenna using the
authorized Wristband Key. The
door will unlock for 6-seconds.
While the door is unlocked, open the
door and enter the truck.
Antennas are located near each door.
The door will unlock for 6-seconds. If the door is
open longer than 6-seconds, the door will auto-lock
when the door is closed.
1
ANTENNA STATUS LEDs
a. There is a red and a green status LED
installed on each antenna.
b. The red LED will flash
once anytime the unlock
switch is pressed.
c. The red LED will flash
twice anytime an authorized
Wristband Key is presented
to the antenna.
d. The green LED will turn on solid anytime the door
is unlocked (6-seconds).
e. The red LED will flash more than twice if there is
a system failure (no data communication) between
the Master curb side antenna and any of the other
antennnas.
3
KEYLESS TRUCK EXIT - UNLOCK
SWITCH
Press the unlock switch and the
corresponding door will unlock for
6-seconds. While the door is unlocked,
open the door and exit the truck. There is
one unlock switch for each door. The curb
side and driver Unlock switches are located
on the dash, the bulkhead and rear door
unlock switches are installed inside the
cargo compartment near it’s door.
2
MANUAL TRUCK ENTRY & EXIT
a. Only the rear door has a
manual key to unlock the
truck cargo compartment and
gain entry to the truck. The cab can
then be entered through the bulkhead
door using the Unlock switch or the manual lever inside
the door latch.
Note: If the manual key is used for entry the security
alarm will need to be deactivated within 5 seconds by
presenting a valid Wristband Key to any antenna. See
Cargo Compartment Security Section 6.
b. All of the doors can be unlocked manually from
inside the truck.
4
Side Door Bulkhead Rear Door
CARGO COMPARTMENT SECURITY
a. Anytime both the bulkhead and rear doors are closed and locked, and the
ignition is OFF, the cargo compartment security zone is armed.
b. The cargo compartment security zone is disarmed anytime an authorized
Wristband Key is presented to the bulkhead or rear door antenna.
c. If the driver remains inside the cargo compartment and closes both bulkhead and
rear doors, the cargo compartment security zone will allow the driver to exit the cargo
area by pressing either Unlock switch, located at the Bulkheard or Rear Door.
d. The cargo compartment zone alarm triggers when either the bulkhead or rear door is opened manually
and NO Valid Wristband Key is presented to any antenna within 5-seconds.
5
CAB & CARGO DOME LAMPS
a. The cab and cargo dome lamps are automatically turned on for 60-seconds when any door is
opened.
b. The cab and cargo dome lamps are automatically turned on for 10-seconds when any door is
opened and the ignition is on.
c. The cab and cargo dome lamps if turned on automatically will turn off any time the truck is started.
d. The cab and cargo dome lamps will turn on maually anytime the Dome Light Dash Switch is pressed and
will ONLY turn off if the Dome Light Switch is pressed again.
6
POWER REDUCTION MODE
a. The system enters the Power Reduction Mode, commonly called the Sleep Mode, anytime no
activity is detected for 30-minutes.
b. The system exits the Power Reduction Mode anytime a valid Wristband Key is presented, an
Unlock switch is pressed or the alarm is triggered.
7
ARMING AND DISARMING THE SECURITY SYSTEM
Arming the Security System
a. Truck is armed anytime all doors are closed.
b. Cargo compartment is armed anytime BOTH doors are closed.
Disarming the Security System
a. Wristband Key is presented to any Antenna or the Keyless Start unit and doors are
closed.
b. Pressing any Unlock switch just prior to opening the corresponding door.
Alarm Triggered
a. If the alarm is triggered, the siren will sound and the dome lights will flash.
b. The Doors Ajar LED will flash until the Keyless Start detects a valid Wristband Key.
Disarming the Security System if the Alarm is Triggered
a. Wristband Key is presented to any door or the Keyless Start unit.
b. Truck ignition is on.
c. Master Key is presented to any Antenna or the Keyless Start unit.
57315 Nagy Drive Warranty
Elkhart, IN 46517 &
Fax: 574-293-1611 Technical Support
www.touchtronics.com 574-294-2570
T O U C H T R O N I C S, I N C. v
v
10
KEYLESS START STATUS LEDs
a. The red Doors Ajar LED will turn on solid anytime the driv-
er, bulkhead or rear doors are open and the truck is off. The
red Doors Ajar LED will flash if the alarm has been triggered.
b. The green Run LED will be on solid anytime the truck is running.
The green Run LED will flash when a valid Wristband Key is authorized
until the Engine Start button is pressed or will timeout at 25 seconds.
c. The yellow Start LED will be on solid when Engine Start button is pressed and the engine can be started.
The yellow Start LED will flash if the Engine Start button is pressed and the engine can’t be started due to a
failed door switch or antenna connector.
d. The red CK SYS LED will flash twice anytime a valid Wristband Key is presented. The red CK SYS LED
will flash continuously during start-up mode if there is a system failure at any antenna. If the truck enters
sleep mode, the CK SYS LED will flash at 5-second ratio until truck exits sleep mode.
KEYLESS STARTING & STOPPING
a. Close the driver, bulkhead and rear doors.
b. Swipe the authorized Wristband Key across the target area on the left side of the
Keyless Start unit.
c. The red CK SYS LED will flash twice, which indicates a valid Wristband Key has been received
and the Keyless Start unit will turn on. The green Run LED will flash for 25 seconds indicating the
truck is ready to be started and the switch backlights will also be on.
d. Check the Doors Ajar LED on the Keyless Start unit. If it is off, then proceed with starting the
truck. If the Doors Ajar status LED is on, then close the driver, bulkhead and/or rear door.
e. Wait for the glow plug indicator light on the dash to turn off and then press the Start switch
marked “ENGINE START”. The yellow Start LED turns on solid indicating the truck starter has been
energized. Release the Engine Start switch as soon as the truck engine is started.
f. To stop the truck and turn off the engine, press the “ENGINE STOP” switch. The engine will turn
off and all of the status LEDs will turn off.
8
9
© 2006 TouchTronics, Inc. All Rights Reserved. TouchTronics, the TouchTronics logo, and other TouchTronics marks are owned by TouchTronics and may be registered.
TouchTronics assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice.
FCC Compliance and Advisory Statement. This hardware device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this
device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Any
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canadian Compliance Statement. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1) this device may not
cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.
© 2006 TouchTronics, Inc. Tous droits réservés. TouchTronics, le logo TouchTronics et les autres marques TouchTronics sont la propriété exclusive de
TouchTronics et sont susceptibles d’être des marques déposées. Toutes les autres marques sont la propriété exclusive de leurs détenteurs respectifs. TouchTronics
décline toute responsabilité en cas d’erreurs dans ce manuel. Les informations énoncées dans le présent document peuvent faire l’objet de modifications sans avis préal-
able.
Déclaration FCC. Cet équipement a été testé et déclaré conforme à la section 15 du règlement de la FCC. Son fonctionnement est soumis aux conditions suivantes: 1)
l’équipement concerné ne doit pas causer d’interférences dangereuses, et 2) il doit accepter toute interférence reçue, y compris les interférences risquant d’engendrer un
fonctionnement indésirable. Toutes modifications ou tous changements effectués sans l’accord exprès de la partie responsable de la conformité aux normes pourraient
contraindre l’utilisateur à ne plus utiliser son équipement.
Déclaration du Ministère des Communications Canadien. Cet équipement a été déclaré conforme à la norme RSS-210 édictée par le Ministère canadien de l’industrie.
Son fonctionnement est soumis aux conditions suivantes: 1) l’équipement concerné ne doit pas causer d’interférences, et 2) il doit accepter toute interférence reçue, y
compris les interférences risquant d’engendrer un fonctionnement indésirable.