Toy State 94155R49 VAPORIZR 2 User Manual FAR 94155 Vaporizr2 ENG IM

Download:
Mirror Download [FCC.gov]
Document ID	2705162
Application ID	kwqbIfFn0dwQzcfVpVbs/w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	263.22kB (3290213 bits)
Date Submitted	2015-08-05 00:00:00
Date Available	2015-08-05 00:00:00
Creation Date	2015-04-08 10:13:08
Producing Software	Adobe PDF library 10.01
Document Lastmod	2015-04-08 10:13:08
Document Title	FAR_94155_Vaporizr2_ENG_IM
Document Creator	Adobe Illustrator CS6 (Macintosh)

CAUTION-ELECTRICALLY OPERATED PRODUCT:
NOT RECOMMENDED FOR CHILDREN UNDER 8 YEARS OF AGE, AS WITH ALL ELECTRIC PRODUCTS, PRECAUTIONS SHOULD BE
OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK,INPUT:120V AC 60Hz 300mA,OUTPUT: 7.5V DC 1000mA.
CONTROLLER
x3
BATTERIES INCLUDED
VEHICLE
RECHARGABLE
6.0V Ni-MH
x1
BATTERY INCLUDED
Important! Carefully read the Owners Manual before play!
8+
#94155
CAUTION
WARNING! CHOKING HAZARD
Small parts. Not for Children under 3 years.
Only operate the product and its accessories when fully
assembled and in accordance with this manual!
This product and its accessorries are not suitable for children under the age of 36 months, because of small
parts that can be swallowed.
Intended for children age 8 and older.
Adult supervision strongly recommended.
Drive your vehicle in a safe area away from people, pets, cars, etc.
Do not drive on streets or after dark.
Do not touch or try to pick up the vehicle when it is in motion. Wait until it has stopped completely.
Keep hair, fingers, face and loose clothing away from front and rear wheels while the vehicle is switched on or
while the transmitter is operating.
Do not drive the vehicle toward walls or other hard objects.
Be a responsible operator!
Do not drop or give impact to the product and its accessories.
Check if a near transmitter produces interference or signals with the same frequency. In such a case, move to
another location or try again after a while.
Never attempt to disassemble or modify the product or its accessories.
Regularly inspect the antennas for cracks or breaks. Do not bend the transmitter antenna. Do not use the
transmitter if the antenna is broken.
The vehicle wire antenna is fragile. Never pull or tug on the antenna, as it may loosen or detach from the vehicle.
Use extra caution when playing near water or ice.
Intended to be used on land and in water.
Do not use the product in salt water or water with strong currents.
BATTERIES AND CHARGER
Included: 6.0V Rechargeable NiMH Battery Pack and Battery Charger for NiMH Battery Pack and
AAA/LR03 battery x3.
IMPORTANT BATTERY SAFETY INFORMATION
CAUTION: TO AVOID BATTERY LEAKAGE (AAA/LR03 and the 6.0V NiMH RECHARGEABLE
BATTERY PACK):
Make sure the batteries are inserted with correct polarity and follow the toy and battery manufacturer's
instructions.
Use only battery type(s) recommended.
Do not attempt to short-circuit, charge, disassemble or heat batteries.
Do not dispose of batteries in fire or make them wet.
Do not mix or use new and old batteries together.
Do not mix or use different types of batteries together.
Non-rechargeable batteries are not to be recharged because of the danger of eruption.
Remove rechargeable batteries from the product before charging.
Recharge batteries only under adult supervision and follow the battery and charger manufacturer's instructions.
Only children of age 8+ are allowed to use the charger and only if used under adult supervision.
Battery replacement should be done in presence of an adult.
Never pull a battery pack out of the vehicle by the wire of the plug.
Remove batteries from the product for storage. Battery may be hot.
After use, be sure to turn the switch off. Failure to do so may adversely affect batteries, resulting in disabled
charged.
Remove weak or exhausted batteries from the product.
Dispose batteries safely and properly, according to your local requirements.
BATTERY CHARGING AND CARE
NOTE: NICKEL-METAL HYDRIDE BATTERIES MUST BE RECYCLED OR DISPOSED
PROPERLY. Contact your local area office of solid waste management or other
appropriate local agency for information.
WARNING: The transformer/ charger is not a toy.
Regularly examine charger and battery pack for leaking, corrosion, damage, including plugs, casings and all
other parts. If damaged, do not use.
Do not short-circuit the charger.
Do not charge batteries with a charger other than the included one.
Do not charge batteries other than the included NiMH battery pack with the charger and do not use the charger
as the power source for other equipment.
Do not charge batteries in a place within the reach of small children.
Do not short-circuit battery terminals, otherwise the battery may swell and get hot, leading to a dangerous
situation.
Do not use, store or charge batteries in a place near a heater or in high temperature or in humid or damp
situations.
Vehicle will not run without a 6.0V rechargeable NiMH battery pack and matching charger, commonly available
for R/C vehicles at many toy and hobby dealers. Always follow the instructions that come with your battery
pack and charger.
Toy must only be used with recommended transformer/ charger.
RUNNING AND CHARGING TIME
NiMH battery packs are not like alkaline batteries. They lose all their power suddenly, not gradually, and the
vehicle will stop very soon after slowing down becomes noticeable, with little warning. This is normal, but keep
it in mind, since you need to get the vehicle back before the battery power runs out.
Battery pack running times depend on the conditions you operate in. Running time may vary over the life of the
battery pack, with the first few charge cycles yielding shorter run times than later charges.
BATTERY CHARGING INSTRUCTIONS
NOTE: "CONDITION" BATTERY PACK FOR BEST RESULTS BY CHARGING ACCORDING TO THESE
INSTRUCTIONS ON EVERY CHARGE. ON THE FIRST CHARGE, EXPECT A SHORTER RUN TIME.
RUN TIMES WILL INCREASE OVER THE NEXT 6 CHARGES.
Drain Down-Cool Down-Charge Up
1. After the first charge, for best performance always run the battery pack fully empty before recharging. Run
until vehicle wheels/rotors/propellers/motors slow to stop.
2. Allow the battery pack to cool before recharging.
Battery Pack Heat
1. Battery pack gets hot after use! This is normal, but be careful. Wait until battery pack is cool (20 minutes or
more if needed) before charging. Charging battery packs when they are hot will severely reduce the number of
times they can be recharged.
2. After charging, battery pack will be warm. This is normal.
RECHARGING INSTRUCTIONS
1.
2.
3.
4.
5.
6.
Plug the battery pack charger into a standard household outlet.
Connect the battery pack to the charger as show in page 5.
Red light on the charger to show that the charger is operating. Normal charging time is 60-80 minutes.
Red light will blink continuously when the battery pack is fully charged.
Unplug the charger from the standard household outlet after 60-80 minutes of charging.
After charging, the battery pack will feel warm, this is normal.
NIMH RECHARGEABLE BATTERY PACK TIPS
Don't overcharge the battery pack, unplug the charger from the household outlet at the end of the
recommended charging time (Approximately 60-80 minutes).
Store your battery pack discharged.
Your battery pack will hold a charge for a shorter time in hot weather.
The charging time is 60-80 minutes. Make sure the charging time will not be longer or shorter then the
advised charging time as that will effect the quality of the battery.
When the use time of this battery pack becomes shorter and shorter, it is most likely time to replace the
battery pack.
If driving time becomes shorter or wheels do not turn with full power, the capacity of the 1.5V battery or 6.0V
battery pack are insufficient. This is the sign indicating that you need to replace the 1.5V battery or recharge
the 6.0V battery pack.
Be sure to recharge the battery pack before driving it. If you do not play with the vehicle immediately after
recharging, the charge is drained and the vehicle cannot drive.
When the battery temperature gets too high, the circuit shuts off automatically to protect the receiver circuit
and the battery in the vehicle. In such a case, wait until the battery cools down before recharging or playing
with the vehicle.
If the rechargeable battery is repeatedly charged without being sufficiently discharged first, the capacity will
gradually decrease (memory effect of battery). This is a characteristic of rechargeable batteries. Be sure to
start recharging after operating the vehicle until they nearly stop.
CAUTION DURING PLAYING WITH VEHICLE
Do not drive your vehicle on streets or in a crowded place.
When the battery pack gets wet, dry completely before storing it.
Do not store the vehicle in a place near a heater or where temperature rises. After use, remove the batteries
from the transmitter and vehicle to store.
This vehicle can run on land and in water but it is not fully water-proof! Immersing it into water may lead to a
malfunction. Dry vehicle well after operating in water.
Adult supervision is strongly recommended when playing near water. Do not drive your vehicle in the sea and
wavy water surface, or where a rapid current flows. Stay away from areas where waves rise due to a strong
wind. Also avoid driving on dirty water surface or where waterweed grows dense, this can cause a malfunction.
Operate your vehicle in water with due care to the distance and battery life, since you need to get the vehicle
back before the battery power runs out.
SAFETY CIRCUIT
During use, the internal power in the electric circuit can get quite high (for example during a 360 spin).
In such a case a safety circuit will shut down the vehicle for approximately 10-15 seconds. During this period the car
will not respond to signals from the transmitter. This is not a defect but a safety measure to protect the electronic
circuits. After this period, the car will resume normal operation.
CONTENTS & FEATURES
Transmitter
VaporizR 2
1.5V (AAA/LR03)
battery x3
NiMH Battery charger
6.0V NiMH battery pack
ANTENNA ASSEMBLY
Insert antenna wire
from product into tube.
Slide tube down
antenna wire and into
hole in product.
Tie knot with any
remaining antenna wire
(Do not pull wire tight).
TRANSMITTER BATTERY INSTALLATION
1.5V
1.5V
1.5V
1. To remove battery lid, loosen screw to open.
2. Slide open the battery lid in the direction as
shown in the figure, while lightly pressing its
center.
3. Insert 1.5V (AAA/LR03) batteres x3 with the
polarity (+/-) as shown on the bottom of
battery compartment.
Replace the battery lid, following the removal
procedure in reverse.
NOTE: For best performance, always use alkaline batteries only. To remove the batteries, reverse the
installation procedure.
There is no on/off switch on the Transmitter. Moving the sticks turns it on automatically.
VEHICLE BATTERY INSTALLATION
OFF
ON
1. Fully charge 6.0V NiMH battery
pack in advance of your use.
2. Turning off vehicle.
3. Turn the latches located underneath
of vehicle to unlock battery lid as
shown in the figure with arrows.
4. Loosen screw to open battery lid.
5. Remove battery lid.
6. Insert 6.0V battery pack into battery
compartment with correct polarity
(+/-). Place battery lid back in
position and lock properly
THIS PRODUCT SHOULD BE USED WITH ADULT SUPERVISION.
NOTE: To remove the batteries, reverse the installation procedure.
OPERATING R/C VEHICLE
OFF
ON
TURN VEHICLE
POWER ON.
FORWARD (Push both sticks forward)
BACKWARDS (Pull both sticks backwards)
LEFT TURN (FORWARD) (Push right stick forward)
RIGHT TURN (BACKWARDS) (Pull right stick backwards)
RIGHT TURN (FORWARD) (Push left stick forward)
LEFT TURN (BACKWARDS) (Pull left stick backwards)
LEFT SPIN (At the same time, pull left stick back
and push right stick forward)
RIGHT SPIN (At the same time, pull right stick back
and push left stick forward)
NOTE: After play, always turn vehicle off. Remove batteries from controller and R/C vehicle when not in
use or when storing. Leakage may occur and cause damage if left for a long period of time.
TROUBLESHOOTING AND CARE FOR R/C VEHICLE
LIMITED RADIO CONTROL RANGE
While R/C vehicle may be visible at a distance, full
operational control may be lost. Hold controller
high in the air and direct vehicle back.
INTERFERENCE
Other radio signals may cause loss of control.
Remove vehicle from an area of interference.
• Are the + and – contacts correctly matched in the controller?
• Are the metal contact tabs touching, rusty or dirty in controller?
• Are there batteries in the vehicle and controller?
• Is the power switch turned to play?
• Are the batteries weak or out of power?
R/C VEHICLE
DOES NOT MOVE
• There is radio interference in the area.
• Another R/C vehicle with the same frequency is close by.
R/C VEHICLE
MOVES BY ITSELF
• There is radio interference in the area.
• Another R/C vehicle with the same frequency is close by.
• Are the batteries weak or out of power?
R/C VEHICLE
RUNS SLOWLY
PERFORMANCE DROP,
INCONSISTENT MOVEMENT
OR FAILS TO RUN
Check batteries. If necessary, recharge battery pack and/or replace the
batteries in the R/C vehicle and controller with new alkaline batteries.
TREAT YOUR R/C VEHICLE WELL
Radio waves control the R/C vehicle. Care for your vehicle and it will provide hours of fun!
Avoid heat, sand and high impact crashes!
Store in safe place.
No Collisions.
No direct sunlight.
R/C vehicle may get stuck
on carpet or grass.
No sand or dust.
Avoid running 2 vehicles with the same radio control
frequencies.
CLEANING AND MAINTAINING
Brush areas where dirt and
dust get trapped.
Wipe body off with a soft rag
or tact cloth.
Do not clean vehicle with
chemicals.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the userʼs
authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
MANUFACTURER’S NOTE
“Modifications not authorized by the manufacturer may void users authority to operate the device.”
ATTENTION PARENTS
This toy and all accessories need to be periodically examined for potential hazards and any
potentially hazardous parts be repaired or replaced.
www.toystate.com
www.NikkoRC.com
For questions, e-mail our Consumer Service Dept.at
consumerservice@toystate.com
Or Call 1-877-473-8015
WARNING:
Not suitable for children under 36 months due to
small parts. Choking hazard.
MADE IN SHENZHEN, CHINA
TOY STATE INTERNATIONAL LIMITED
66 MODY ROAD, KOWLOON, HONG KONG
IN THE INTEREST OF BETTER QUALITY AND VALUE, WE ARE CONSTANTLY IMPROVING AND UPDATING OUR PRODUCTS.
CONSEQUENTLY, PICTURES IN THIS INSTRUCTION SHEET MAY SOMETIMES DIFFER FROM THE MODEL ENCLOSED.
9
www.toystate.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Format                          : application/pdf
Title                           : FAR_94155_Vaporizr2_ENG_IM
Metadata Date                   : 2015:04:08 10:13:08+08:00
Modify Date                     : 2015:04:08 10:13:08+08:00
Create Date                     : 2015:04:08 10:13:08+08:00
Creator Tool                    : Adobe Illustrator CS6 (Macintosh)
Thumbnail Width                 : 188
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 5716 bytes, use -b option to extract)
Instance ID                     : uuid:51e64d8d-361b-0b49-a2c9-9470b2ba4f03
Document ID                     : xmp.did:0380117407206811822ABB263DED8793
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:e84b419f-b03d-9642-903a-0e00938e8e52
Derived From Document ID        : xmp.did:0580117407206811822AF6078F31DB5A
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:075748CE30206811822ACD9B0D1E2798, xmp.iid:0380117407206811822ABB263DED8793
History When                    : 2015:02:26 17:25:11+08:00, 2015:04:08 10:12:56+08:00
History Software Agent          : Adobe Illustrator CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh)
History Changed                 : /, /
Manifest Link Form              : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference
Manifest Reference File Path    : /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd, /Volumes/WAREHOUSE/94155 VAPORIZR MANUAL/N_RC.psd
Startup Profile                 : Print
Has Visible Overprint           : True
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 139.700000
Max Page Size H                 : 208.280138
Max Page Size Unit              : Millimeters
Font Name                       : DIN-Bold, DINOT-Bold, Helvetica-Condensed, Helvetica-Condensed-Bold, Helvetica-Bold, HelveticaNeue-Condensed, HelveticaNeue-CondensedBold, HelveticaNeueLTPro-BdCn, LucidaGrande, MotionControl-BoldItalic, MyriadPro-SemiboldCond, Tahoma-Bold
Font Family                     : DIN, DIN OT, Helvetica, Helvetica, Helvetica, Helvetica Neue, Helvetica Neue, Helvetica Neue LT Pro, Lucida Grande, Motion Control, Myriad Pro, Tahoma
Font Face                       : Bold, Bold, Medium Condensed, Bold Condensed, Bold, 57 Condensed, Condensed Bold, 77 Bold Condensed, Regular, BoldItalic, Semibold Condensed, Bold
Font Type                       : Open Type, Open Type, Type 1, Type 1, TrueType, Type 1, TrueType, Open Type, TrueType, Open Type, Open Type, Open Type
Font Version                    : 001.000, Version 7.504; 2005; Build 1020, 001.004, 001.005, 9.0d3e2, 001.000, 9.0d57e1, Version 1.500;PS 001.005;hotconv 1.0.38, 9.0d11e1, Version 1.0, Version 2.006;PS 002.000;Core 1.0.38;makeotf.lib1.6.6565, Version 5.01.1x
Font Composite                  : False, False, False, False, False, False, False, False, False, False, False, False
Font File Name                  : DIN-Bold.otf, DINOT-Bold.otf, HelveCon; Helv_Condensed Screen Fonts, HelveConBol; Helv_Condensed Screen Fonts, Helvetica.dfont, HelveNeuCon; Helvetica Neue Condensed, HelveticaNeue.dfont, HelveticaNeueLTPro-BdCn.otf, LucidaGrande.ttc, MotionControl-BoldItalic.otf, MyriadPro-SemiboldCond.otf, Tahoma Bold.ttf
Plate Names                     : Cyan, Magenta, Yellow, Black, PANTONE 186 C
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Colorants L       : 45.882401
Swatch Groups Colorants A       : 12
Swatch Groups Colorants B       : -50
Swatch Groups Group Name        : Brights
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000004
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003099
Swatch Groups Colorants Black   : 0.003099
Producer                        : Adobe PDF library 10.01
Page Count                      : 12
Creator                         : Adobe Illustrator CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools