Trane Bas Apg001 En Users Manual

2015-01-21

• Contents
• Chapter 1, Smoke control overview
  • Methods of smoke control
    • Compartmentation method
    • Dilution method
    • Pressurization method
    • Airflow method
    • Buoyancy method
  • Applications of smoke control methods
    • Zoned smoke control
    • Stairwell smoke control
    • Elevator shaft smoke control
    • Atrium smoke control
    • Underground building smoke control
  • Smoke detection and system activation
    • Zoned smoke control detection and activation
    • Stairwell smoke control detection and activation
    • Elevator smoke control detection and activation
    • Atrium smoke exhausting detection and activation
  • Design approaches to smoke control
    • No-smoke approach
    • Tenability approach
    • Dedicated system approach
  • Design considerations for smoke control
    • Plugholing
    • Smoke feedback
• Chapter 2, Pre-installation considerations
  • Zone operating modes
    • Normal mode
    • Alarm mode
    • Adjacent mode
    • Unaffected mode
  • Associated equipment
    • Fire alarm system equipment
    • Fire alarm control panel
    • Smoke control system equipment
  • Equipment supervision
  • System testing
    • Automatic weekly self-testing
    • Manual periodic testing
  • Alarm response
  • Automatic smoke control matrix
  • Response times
  • Cable distance considerations
• Chapter 3, Installation diagrams
  • Smoke control system overview
  • System riser diagrams
  • System termination diagrams
    • Tracer MP581 to FSCS wiring
    • Tracer MP581 to FACP wiring
• Chapter 4, Installing the Tracer Summit BMTX BCU
  • Mounting the hardware
    • Operating environment requirements
    • Clearances
  • Mounting the back of the enclosure
  • Wiring high-voltage ac power
  • EMI/RFI considerations
    • Checking the earth ground
  • Connecting the main circuit board
  • Installing the door
  • Transtector, Ethernet (UUKL nondedicated only), and LonTalk connections on the BMTX BCU
• Chapter 5, Installing the Tracer MP581 programmable controller
  • Installation guidelines
  • Specifications
  • Selecting a mounting location
    • Operating environment requirements
    • Clearances and dimensions
  • Mounting the back of the enclosure
  • Wiring high-voltage ac power
    • Circuit requirements
    • Wiring high-voltage power
  • EMI/RFI considerations
    • Checking the earth ground
  • Wiring inputs and outputs
    • Input/output wiring guidelines
    • Wire routing
    • Providing low-voltage power for inputs and outputs
    • Screw terminal locations
    • Wiring universal inputs
    • Wiring analog outputs
    • Wiring binary outputs
    • Checking binary inputs
  • Checking outputs
    • Checking binary outputs
    • Checking 0-10 Vdc analog outputs
    • Checking 0-20 mA analog outputs
  • Wiring LonTalk to the Tracer MP581
  • Installing the circuit board
  • Verifying operation and communication of the Tracer MP581
    • Service Pin button
    • Interpreting LEDs
    • Binary output LEDs
    • Service LED
    • Status LED
    • Comm LED
  • Installing the door
    • Removing the door
• Chapter 6, Installing the EX2 expansion module
  • Storage environment
  • Mounting location
  • Terminal strips
  • Mounting the metal-enclosure module
  • AC-power wiring
    • Wiring AC-power to the metal-enclosure module
  • I/O bus wiring
  • Setting the I/O bus addresses
  • Input/output terminal wiring
    • Universal inputs
    • Binary outputs
    • Analog outputs (UUKL nondedicated only)
  • Analog output and universal input setup
  • Interpreting EX2 LEDs
    • Binary output LEDs
    • Status LED
    • Communications LEDs
• Chapter 7, Programming
  • Response times
  • Operational priority
  • Subsequent alarms
  • Smoke alarm annunciation
  • Weekly self-test of dedicated systems
  • End process verification
  • Communication watchdog
  • Lamp test and audio alarm silence
  • Nondedicated smoke purge
  • Variable-air-volume system
  • Constant-volume system
  • UL-tested programs
• Chapter 8, Network variable bindings
  • Overview
  • Binding network variables
  • Tracer MP580/581 bindings
    • Receiving data
    • Sending data
    • Heartbeated network variables
  • Custom bindings
    • UUKL binding list (watchdog communication)
    • UUKL binding list (smoke alarm status)
    • UUKL binding list (FCSP override control)
    • UUKL binding list (actuator Open/Close or On/Off status)
    • UUKL binding list (actuator failure status)
    • UUKL binding list (FSCP control)
    • UUKL binding list (automatic self-test trigger and status)
    • Custom binding report
  • Understanding bindings
    • Node
    • Binding types
    • Basic binding shapes and the hub/target system
    • Designing bindings
• Appendix A, References