Trane Ptac Svx01C En Users Manual

ptacsvx01cen 7683f12c-60ab-4bef-9b28-519a96997237 Trane Air Conditioner PTAC-SVX01C-EN User Guide |

: Trane Trane-Ptac-Svx01C-En-Users-Manual-236119 trane-ptac-svx01c-en-users-manual-236119 trane pdf

Open the PDF directly: View PDF .
Page Count: 52

Installation,

Operation, and

Maintenance

September 2006 PTAC-SVX01C-EN

PTEE070/PTHE070 (7,000 Btuh)

PTEE090/PTHE 090 (9,000 Btuh)

PTEE120/PTHE120 (12,000 Btuh)

PTEE150/PTHE150 (15,000 Btuh)

Packaged Terminal Air

Conditioner

2PTAC-SVX01C-EN

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Model Number Description . . . . . . . . . . . . . . . . . . . . . . . . .3

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Ta b l e 1. Minimum interior and exterior projections . . . . . . . .6

Table 2. Minimum clearances and projections . . . . . . . . . . .7

Receiving and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Energy Management System . . . . . . . . . . . . . . . . . . . . . . 19

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Refrigeration System Service . . . . . . . . . . . . . . . . . . . . . . 31

Brazing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Evacuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cooling Performance Test . . . . . . . . . . . . . . . . . . . . . . . . . 35

Ground Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 27. Thermistor indoor coil resistance . . . . . . . . . . . . 38

Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 28. Diagnostic codes . . . . . . . . . . . . . . . . . . . . . . . 41

Table 29. Latching diagnostics, reset required . . . . . . . . . 41

Table 30. Automatically resetting diagnostics . . . . . . . . . . 41

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Full 1st Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Full 2nd - 5th Sealed System Warranty . . . . . . . . . . . . . . . 50

Limited 2nd through 5th Year Functional Parts Warranty 50

Table of Contents

PTAC-SVX01C-EN 3

*All heat pump units must have electric heat.

Digit 8—Main Power Supply

1 = 230-208V/60Hz/1phase

2 = 265V/60Hz/1phase

4 = 115V/60Hz/1phase (Hydronic Only)

Digit 9 —Electric Heat Capacity*

U = Universal Heater (Heater kW determined by

power cord, see Accessories Section)

W = Hydronic (ships with no front cover & no

electric heater)

Digit 10 — Unit Features

A = Standard

C = Corrosion Resistant

D = Internal Condensate Pump

Digit 11—Minor Design Sequence

Model Number Description

P T E E 0 9 0 1 * A A

1 2 3 4 5 6 7 8 9 10 11

Each Packaged Terminal Air

Conditioner/Heat Pump is assigned a

multiple-character alphanumeric

model number that precisely

identifies each unit.

An explanation of the identification

code that appears on the unit

nameplate is shown below.

The model number helps owner/

operator, installing contractors, and

service technicians to define the

operation, components and options

for a specific unit.

Refer to the model number printed

on the equipment nameplate when

ordering replacement parts or

requesting service.

Front and discharge grille

Electric heater

Indoor Fan

Display Module

Outdoor fan

Wall sleeve

Outdoor grille

Outdoor coil

Rotary compressor

Power cord coverplate (not shown)

Power cord

Control box

Indoor coil

Digits 1, 2—Packaged Terminal Air Conditioner

Digit 3—Product Type

E = Air Conditioner with auxiliary heat

H= Heat Pump

Digit 4—Development Sequence

E = Fifth Development Series

Digit 5, 6, 7—Unit Cooling Capacity

070 = 7,000 Btu

090 = 9,000 Btu

120 = 12,000 Btu

150 = 15,000 Btu

General Information

© 2005 American Standard Inc. All rights reserved PTAC-SVX01C-EN

NOTICE:

Warnings and Cautions appear in

appropriate sections throughout this

manual. Read these carefully.

WARNING

Indicates a potentially hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a potentially hazardous

situation which, if not avoided, may

result in minor or moderate injury. It

may also be used to alert against

unsafe practices.

CAUTION

Indicates a situation that may result

in equipment or property-damage-

only accidents.

Overview of Manual

Note: One copy of this document

ships with each unit and is

customer property. It must be

retained by the customer.

This booklet describes proper

installation, operation, and

maintenance procedures for PTACs.

By carefully reviewing the

information within this manual and

following the instructions, the risk of

improper operation and/or

component damage will be

minimized.

It is important that periodic

maintenance be performed to help

assure trouble free operation. A

maintenance schedule is provided at

the end of this manual. Should

equipment failure occur, contact a

service organization with qualified,

experienced HVAC technicians to

properly diagnose and repair this

equipment.

Important

Environmental Concerns!

Scientific research has shown that

certain man-made chemicals can

affect the earth’s naturally occurring

stratospheric ozone layer when

released to the atmosphere.

In particular, several of the identified

chemicals that may affect the ozone

layer are refrigerants that contain

Chlorine, Fluorine and Carbon (CFCs)

and those containing Hydrogen,

Chlorine, Fluorine and Carbon

(HCFCs).

Not all refrigerants containing these

compounds have the same potential

impact to the environment.

The manufacturer advocates the

responsible handling of all

refrigerants—including industry

replacements for CFCs such as

HCFCs and HFCs.

Responsible Refrigerant

Practices!

The manufacturer believes that

responsible refrigerant practices are

important to the environment, our

customers, and the air conditioning

industry.

All technicians who handle

refrigerants must be certified. The

Federal Clean Air Act (Section 608)

sets forth the requirements for

handling, recovering, recycling and

reclaiming of certain refrigerants and

the equipment that is used in these

service procedures.

In addition, some states or

municipalities may have additional

requirements that must also be

adhered to for responsible

management of refrigerants. Know

the applicable laws and follow them.

WARNING

Hazardous Voltage with

Capacitators!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

Disconnect all electric power,

including remote disconnects and

discharge all motor start/run

capacitors before servicing. Follow

proper lockout/tagout procedures to

ensure the power cannot be

inadvertently energized. Verify with

an appropriate voltmeter that all

capacitors have discharged. Failure

to disconnect power and discharge

capacitors before servicing could

result in death or serious injury.

CAUTION

Use Copper Conductors Only!

Unit terminals are not designed to

accept other types of conductors.

Failure to use copper conductors

may result in equipment damage.

General Information

PTAC-SVX01C-EN 5

General Information

Refrigerant Handling

Procedures

WARNING

Contains Refrigerant!

System contains oil and refrigerant

under high pressure. Recover

refrigerant to relieve pressure before

opening the system. See unit

nameplate for refrigerant type. Do

not use non-approved refrigerants,

refrigerant substitutes, or refrigerant

additives.

Failure to follow proper procedures

or the use of non-approved

refrigerants, refrigerant substitutes,

or refrigerant additives could result

in death or serious injury or

equipment damage.

Environmental Accountability

Policy

The manufacturer urges that all

HVAC servicers make every effort to

eliminate, if possible, or vigorously

reduce the emission of CFC, HCFC,

and HFC refrigerants to the

atmosphere. Always act in a

responsible manner to conserve

refrigerants for continued usage

even when acceptable alternatives

are available.

Recover and Recycle

Refrigerants

Never release refrigerant to the

atmosphere!

Always recover and/or recycle

refrigerant for reuse, reprocessing

(reclaimed), or properly dispose if

removing from equipment.

Always determine the recycle or

reclaim requirements of the

refrigerant before beginning the

recovery procedure.

Obtain a chemical analysis of the

refrigerant if necessary.

Questions about recovered

refrigerant and acceptable refrigerant

quality standards are addressed in

ARI Standard 700.

Refrigerant Handling and

Safety

Consult the manufacturer’s material

safety data sheet (MSDS) for

information on refrigerant handling

to fully understand health, safety,

storage, handling, and disposal

requirements.

Use only approved containment

vessels and refer to appropriate

safety standards. Comply with all

applicable transportation standards

when shipping refrigerant

containers.

Service Equipment and

Procedures

To minimize refrigerant emissions

while recovering refrigerant, use the

manufacturer’s recommended

recycling equipment per the MSDS.

Use equipment and methods which

will pull the lowest possible system

vacuum while recovering and

condensing refrigerant. Equipment

capable of pulling a vacuum of less

than 1,000 microns (1.0 mm) of

mercury is recommended.

Do not open the unit to the

atmosphere for service work until

refrigerant is fully removed/

recovered.

When leak-testing with trace

refrigerant and nitrogen, use HCFC-

22 (R-22) rather than CFC-12 (R-12) or

any other fully-halogenated

refrigerant.

Be aware of any new leak test

methods which may eliminate

refrigerants as a trace gas.

Perform evacuation prior to charging

with a vacuum pump capable of

pulling a vacuum of 1,000 microns

(1.0 mm) of mercury or less. Let the

unit stand for 12 hours and with the

vacuum not rising above 2,500

microns (2.6 mm) of mercury.

A rise above 2,500 microns (2.5 mm)

of mercury indicates a leak test is

required to locate and repair any

leaks. A leak test is required on any

repaired area.

Charge refrigerant into the

equipment only after equipment

does not leak or contain moisture.

Refer to proper refrigerant charge

requirements in the maintenance

section of this manual to ensure

efficient machine operation.

When charging is complete, purge or

drain charging lines into an approved

refrigerant container.

Seal all used refrigerant containers

with approved closure devices to

prevent unused refrigerant from

escaping to the atmosphere.

Take extra care to properly maintain

all service equipment directly

supporting refrigerant service work

such as gauges, hoses, vacuum

pumps, and recycling equipment.

When cleaning system components

or parts, avoid using CFC-11 (R-11) or

CFC-113 (R-113). Use only cleaning-

solvents that do not have ozone

depletion factors.

Properly dispose of used materials.

Refrigeration system cleanup

methods using filters and driers are

preferred.

Check for leaks when excessive

purge operation is observed.

Keep abreast of unit enhancements,

conversion refrigerants, compatible

parts, and manufacturer’s

recommendations that will reduce

refrigerant emissions and increase

equipment operating efficiencies.

6PTAC-SVX01C-EN

Pre-Installation

Pre-Installation

Considerations

Before beginning installation, make

the following considerations:

1. Verify the wall opening is in the

correct location and the

correct size.

2. Drill mounting holes on both

sides of the wall sleeve, if

equipment requires any of the

following options: subbase,

leveling legs, or hydronic heat

kit.

If dimension A in Figure 2 is at or

near the minimum specified in

Ta b l e 2 , p . 7 , accessory options

should be mounted to the sleeve

prior to installing the sleeve in

the wall. Otherwise, there may

not be enough access room for

the tools used to mount the

accessories to the wall sleeve.

3. If additional wall sleeve support

is required, the leveling leg

accessory kit or a subbase kit

that includes leveling legs can be

used to provide extra support.

4. If installing in a concrete or

masonry wall, you must provide

a lintel in the wall opening for

support. Do not use the wall

sleeve as a lintel.

See Figure 1 for a typical lintel

construction.

5. When installing in walls that are

deeper than 13 1/2 inches, use an

extended wall sleeve. A sleeve

without the proper depth will

require special care to prevent

problems with rain water,

condensate drainage, and intake/

discharge air.

Figure 1. Typical Installation

framing with lintel

Under these circumstances,

careful jobsite analysis and

cautions are required. Consult

your local HVAC representative

before attempting such

installations.

Checklist

The following checklist provides an

overview of the factory-

recommended pre-installation

considerations. Follow the

procedures in this section to ensure

the installation is complete and

adequate for proper unit operation.

Verify this checklist is complete

before beginning unit installation.

• If unit arrives shipped on its side,

do not accept.

• Verify the unit size and tagging

with the unit nameplate to

ensure the correct unit is

received.

• Inspect the unit for possible

shipping damage and make any

necessary claims with the freight

delivery company immediately.

• Verify the installation location is

free of airflow obstructions, such

as curtains, furniture, trees, or

other objects that may block

airflow to and from the unit.

WARNING

Fire Hazard!

Do not use extension cords. Using

extension cords could cause a fire.

• Make provisions for correct

supply power and that the

electrical receptacle is within 52

inches of the lower right corner

of the equipment.

• Ensure the unit wall opening is

level.

• Ensure adequate sealing and

insulation is around the wall

sleeve.

Figure 2. Minimum unit clearance

Table 1. Minimum interior and exterior

projections

Figure 3. Minimum wall opening

dimensions

42 1/2” min.

Finished

Floor

16 1/4” min.

Dimension B

Pre-Installation

PTAC-SVX01C-EN 7

Pre-Installation

Receiving and Handling

Shipping Package

The chassis and the cabinet front

ship in one carton. Accessories ship

separate.

Receiving Checklist

Complete the following checklist

immediately after receiving unit

shipment to detect possible shipping

damage.

• Verify that the unit nameplate

data corresponds to the sales

order and bill of lading (including

electrical data).

• Visually inspect the unit exterior

for physical signs of shipping

damage or material shortages.

• If a unit appears damaged,

inspect it immediately before

accepting the shipment. Remove

access panels and check for

interior component damage.

Make specific notations

concerning the damage on the

freight bill. Do not accept

delivery.

Table 2. Minimum clearances and

projections

Option In. Mm In. Mm In. Mm

Minimum clearances Minimum projection

AB C

Wall sleeve only 3 75 0 0 0 0

Subbase kit 3 75 3 1/4 85 2 3/4 70

Leveling legs kit 3 75 3 75 2 50

Hydronic heat kit(1)

(1) Max height is based on skirt options available.

9 230 2-6”(2)

(2) This dimension can be from 2-6", but if this dimension exceeds 6" an extended standard kick plate is

necessary.

50 -150(3)

(3) This dimension can be from 50-150mm, but if this dimension exceeds 150mm an extended standard kick

plate is necessary.

3-3 1/8(4)

(4) To achieve a flush fit between the hydronic front and the finished wall, dimension "C" must be between

3" and 3-1/8". If this dimension is more than 3-1/8" there will be a gap between the front and the wall.

This gap could permit occupant access to hydronic lines or other dangerous parts.

76-80(5)

(5) To achieve a flush fit between the hydronic front and the finished wall, dimension "C" must be between

76-80mm. If this dimension is more than 80mm there will be a gap between the front and the wall. This

gap could permit occupant access to hydronic lines or other dangerous parts.

Drain kit 3 75 0(6)

(6) If inside mounted then B = 1-1/2 inches

1(7)

(7) If inside mounted then B = 40 mm

00

Hardwire kit 3 75 3 75 0 0

• Report concealed damage to the

freight line within the allotted

time after delivery. Verify with

the carrier what their allotted

time is to submit a claim.

Note: Failure to follow these

procedures may result in no

reimbursement for damages

from the freight company.

• Do not move damaged material

from the receiving location. It is

the receiver’s responsibility to

provide reasonable evidence that

concealed damage did not occur

after delivery.

• Do not continue unpacking the

shipment if it appears damaged.

Retain all packaging. Take photos

of damaged material if possible.

• Notify the carrier’s terminal of the

damage immediately by phone

and mail. Request an immediate

joint inspection of the damage by

the carrier and consignee.

• Notify your HVAC representative

of the damage and arrange for

repair. Have the carrier inspect

the damage before making any

repairs to the unit.

8PTAC-SVX01C-EN

Unit Dimensions

Figure 4. Unit with wall sleeve and subbase accessory

Figure 5. Wall Sleeve

Unit Dimensions

PTAC-SVX01C-EN 9

Unit Dimensions

Figure 6. Top view of the hydronic kit

Figure 7. Hydronic kit front view

Figure 8. Hydronic kit side view

PTAC Wall Sleeve

Air discharge Unit controls

compartment

1“

20-1/4”

16-1/5”

1-1/20”

53-2/3”

PTAC

Air inlet

Steam inlet and outlet connection

(right hand coil connection)

Steam/water

coil position

Hotwater or steam inlet and outlet

connection (left hand coil connection)

Front View

12.62

5.00”

1-3/8” - 1-1/2”

Top of wall sleeve

Hydronic front

Toe plate 0 to 3.0” long

Bottom of wall sleeve

10 PTAC-SVX01C-EN

Installation

WARNING

Live Electrical Components!

During installation, testing, servicing

and troubleshooting of this product,

it may be necessary to work with live

electrical components. Have a

qualified licensed electrician or other

individual who has been properly

trained in handling live electrical

components perform these tasks.

Failure to follow all electrical safety

precautions when exposed to live

electrical components could result in

death or serious injury.

WARNING

Fire Hazard!

Do not use an extension cord with

this unit. Doing so may cause a fire.

CAUTION

Use Copper Conductors Only!

Unit terminals are not designed to

accept other types of conductors.

Failure to use copper conductors

may result in equipment damage.

Electrical Requirements

The PTAC can be powered by a

power cord connected to a receptacle

in the wall or in a subbase. It can also

be connected directly to the building

supply wires with a hard wire kit.

For U.S. approval, 265V units must

have a permanent wiring connection.

This requirement can be met either

by supplying a subbase for

concealed cord connection or by

direct wiring with the hard wire kit.

The power cord measures 60 inches,

with 56 inches usable from the point

where the cord exits the unit cabinet

and the attached plug.

Installation

PTAC-SVX01C-EN 11

Installation

Table 3. Electric heat capacity and electrical data, models PTEE and PTHE(i)

Nominal heating Building circuit requirement

Voltage(ii)

Electric

heater

Size (kW)

# of

stages

Btu/h at

230/208V

Btu/h at

265V

Total

watts(iii)

Unit

total

amps

Minimum

ampacity(iv)

Maximum

protection(v) Plug

230/208 2.0/1.6 1 6,800/

5,500

- 2000/

1600

8.9/7.9 11.4 15 6 - 15 P

230/208 3.0/2.4 1 10,200/

8,200

- 3000/

2400

13.4/11.8 17 20 6 - 20 P

230/208 5.0/4.0 1 17,100/

13,700

- 5000/

4000

22.2/19.7 28 30 6 - 30 P

265 2.0 1 - 6,800 2000 7.7 9.8 15 7 - 20 P

265 3.0 1 - 10,200 3000 11.6 14.7 15 7 - 20 P

265 5.0 1 - 17,100 5000 19.3 24.4 25 7 - 30 P

(i) All heat pumps have electric heat.

(ii) Minimum voltage on 230/208 volt models is 187 volts; maximum is 253 volts. Minimum voltage on 265 volt models is 239 volts; max-

imum is 292 volts.

(iii) Total watts for 7,000 and 9,000 Btu models; add 70 watts for 12,000 and 15,000 Btu models.

(iv) Minimum branch circuit ampacity ratings conform to the National Electric Code. However, local codes should apply.

(v) Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265 volt models must be cartridge-

style time delay fuses.

Table 4. Power receptacle configurations

Unit

Voltage

Rating

230/

208

230/

208

230/

208 265 265

Unit plug

Plug amp

rating

15 20 30 15/20 30

NEMA

designation

6-15P 6-20P 6-30P 7-15P/7-20P 7-30P

Receptacle

Receptacle

amp rating

20 20 30 20 30

NEMA

designation

6-20R 6-20R 6-30R 7-20R 7-30R

12 PTAC-SVX01C-EN

Installation

Installation Procedure

WARNING

Hazardous Voltage w/

Capacitors!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power cannot be inadvertently

energized. For variable frequency

drives or other energy storing

components provided by Trane or

others, refer to the appropriate

manufacturer’s literature for

allowable waiting periods for

discharge of capacitors. Verify with

an appropriate voltmeter that all

capacitors have discharged. Failure

to disconnect power and discharge

capacitors before servicing could

result in death or serious

injury.Install components in this

order.

1. Remove rear closure panel from

wall sleeve.

2. Install drain kit (optional).

3. Install outdoor air grille in wall

sleeve.

Figure 9. Panel wall installation

4. Install wall sleeve in wall

opening.

5. Install unit chassis in wall sleeve.

6. Install unit power supply.

•Power cord

•Hard wire kit

• Subbase kit

• Electrical receptacle

• Power switch

• Cicuit breaker

7. Install unit controls.

• Display module

• Remote wall thermostat

8. Configure display module

settings.

9. Progammable settings.

Step 1. Remove rear closure

panel from wall sleeve.

1. Remove the zigzag folded

cardboard sleeve stiffener. See

Figure 10. Remove the rear

closure panel by folding the four

flaps as indicated in Figure 11

Figure 10. Wall sleeve stiffener

Figure 11. Sleeve rear closure

panel

PTAC-SVX01C-EN 13

Installation

2. Grasping the top and bottom

flanges of the rear closure panel

as shown in Figure 12, the entire

panel is pulled out diagonally

from one side.

Step 2. Install drain kit in wall

sleeve.

Drain kits are available for indoor or

outdoor installation to help

condensate drain from either the

right or left side of the wall sleeve

externally, or from the bottom of the

sleeve internally.

Note: For installation procedures,

please refer to the Installation

Guide that accompanied the

accessory.

If you do not use the drain kit,

condensate will drain out of the rear

of the wall sleeve. The drain kit must

be installed before the outdoor grille

is installed.

Step 3. Install outdoor air

grille in wall sleeve.

An outdoor air grille directs airflow

for proper unit operation and to

protect the outdoor coil. Install the

grille before installing the chassis.

Outdoor air grille options are either a

stamped grille or an architectural

grille. When replacing an old chassis

with an existing grille, please check

with your HVAC representative to

determine if the new chassis can be

used with the old outdoor grille.

Using the wrong type outdoor grille

can decrease cooling or heating

capacity, increase energy usage, or

shorten compressor life.

Note: For installation procedures,

please refer to the Installation

Guide that accompanied the

accessory.

Figure 12. Pull rear closure panel

out of wall sleeve

Step 4. Install wall sleeve in

wall opening.

For condensate to drain properly

inside the unit, the sleeve must be

installed properly:

• level from right to left

• with a slight downward pitch

from the indoor side to the

outdoor side

Note: If equipment is 230/208 volt,

verify the electrical receptacle

is located within 52 inches of

the sleeve’s right hand corner.

Do not use an extension cord.

Note: For installation procedures,

please refer to the Installation

Guide that accompanied the

accessory.

5. Install unit chassis in wall

sleeve.

WARNING

Fire Hazard!

Do not use an extension cord with

this unit. Doing so may cause a fire.

1. Attach the insulation strip to the

upper rear of the wall sleeve. See

Ta b l e 1 3 . If using an extended

wall sleeve, attach the insulation

strip between the two baffles,

touching the baffle surface facing

towards the front.

2. Remove the cabinet front from

the chassis by pulling the bottom

of the cabinet front away from

the chassis until the retaining

clips disengage.

3. If using a subbase, be sure the

right-hand subbase cover is

removed before installing the

chassis in the wall sleeve.

Figure 13. Insulation strip location

Front 11”

Bottom

Rear

4. Slide the chassis into the wall

sleeve until the chassis flanges

contact the front edge of the wall

sleeve. See Figure 14.

5. Secure the chassis to the wall

sleeve using three screws on

each side of the chassis to ensure

a proper seal between the

chassis and the wall sleeve . The

screws are supplied in a plastic

bag which is attached to the

power cord. See Figure 15.

6. Verify the indoor and outdoor

grilles are free of airflow

obstructions.

7. Make the power supply

connections as detailed in the

next step.

Step 6. Install unit power

supply.

Note: For installation procedures,

please refer to the Installation

Guide that accompanied the

accessory.

Figure 14. Slide unit chassis into

the wall sleeve

Figure 15. Secure chassis to wall

sleeve

14 PTAC-SVX01C-EN

Installation

1. All units required either a power cord or hard wire kit to power the unit

2. The Hydronic chassis "W" ships with no electric heat

3. All Hydronic Chassis "W" units required a power cord

4. All 265volt Hydronic chassis "W" required subbase, fuses and socket.

Table 5. Unit power supply

Voltage Options Accessory Accessory part number

115V

Option 1.

Required: Universal Power Cord 15

Amp

BAYPCRD007

A field supplied 115 volt 15 amp receptacle is mounted

in the building floor or wall. A Trane 115 volt 15 amp

power cord BAYPCRD007 is connected to the PTAC and

plugged into the receptacle.

Option 2.

Required: Universal Power Cord 15

Amp

BAYPCRD007

Universal Subbase BAYSUB001

A Trane subbase BAYSUB001 is attached to the wall

sleeve. A field supplied 115 volt 15 amp receptacle is

mounted into the subbase. A Trane 115 volt 15 amp

power cord BAYPCRD007 is connected to the PTAC and

plugged into the receptacle

Option 3. Required: Hard Wire Kit BAYHWRK001

Connector for Hardwire

Kit for 15 Amp

BAYCNHK031

A Trane hardwire kit BAYHRK001 is direct wired to the

building power supply and attached to the PTAC. A

Trane connector kit BAYCNHK031 is connected to the

PTAC and connected to the hard wire kit in the unit

mounted junction box

265 V

Option 1. Required: Universal Subbase BAYSUB001

Socket for subbase 20 or

30 Amp

BAYSCKT003, BAYSCKT004

Universal Power Cord

15,20 or 30 Amp

BAYPCRD004, BAYPCRD005,

BAYPCRD006

Fuses 15, 20 or 30 Amp BAYFUSE001, BAYFUSE002,

BAYFUSE003

Optional Power Switch BAYPSW002

Option 2. Required: Hard Wire Kit BAYHWRK001

Connector for Hardwire

Kit for 15, 20 or 30 Amp

BAYCNHK021, BAYCNHK022 ,

BAYCNHK023

Optional Power Switch if 30 Amp BAYPSW002

230/ 208 V

Option 1. Required: Universal Power Cord

15,20 or 30 Amp

BAYPCRD001, BAYPCRD002,

BAYPCRD003

Optional Power Switch BAYPSW002

Option 2. Required: Universal Subbase BAYSUB001

Socket for subbase 20

or 30 Amp

BAYSCKT001, BAYSCKT002

Universal Power Cord

15,20 or 30 Amp

BAYPCRD001, BAYPCRD002,

BAYPCRD003

Optional Circuit Breaker 15, 20 or

30 Amp

BAYCBKR001, BAYCBKR002,

BAYCBKR003

Power Switch BAYPSW002

Option 3. Required: Hard Wire Kit BAYHWRK001

Connector for Hardwire

Kit for 15, 20 or 30 Amp

BAYCNHK011, BAYCNHK012,

BAYCNHK013

Optional Power Switch BAYPSW002

Step 7. Install the unit

controls.

The PTAC controller’s normal

operation can be operated by using

either

• Display module - can be wall-

mounted or unit mounted.

• Remote Class 2 thermostat -

For Remote Class 2 Thermostat

Installation, read installation,

operation, and maintenance booklet

carefully.

Look in Wiring Diagram section for

information on wiring.

If a remote thermostat is connected,

the unit's display will not be present

and the controller's normal space

temperature control functionality is

overridden by the remote device.

When the controller is being directed

by a remote thermostat, the

following inputs/functions are

disabled or not present:

1. User display inputs (setpoint/

mode/fan)

2. Dehumidification

3. Configuration setup (indoor fan,

setpoint limits, EMS offset,

display units)

4. Energy management system

5. Manual Test

Unit functions that remain under

direct supervision of the controller

are:

1. Random Restart

2. Heat Pump OAT switchover

3. Tubing burst protection

4. Room freeze protection

5. Indoor coil freeze protection

6. Defrost control

When connected to a remote

thermostat, the controller interprets

the combination of thermostat inputs

as its operating mode and behaves

accordingly.

It is recommended to use a small

screwdriver to gently pryt the

removable treminal block "TB2" up

and off for easy connection.

PTAC-SVX01C-EN 15

Installation

Note: If using a third party

thermostat to control the

unit, the thermostat must

have a clearly marked OFF

state or position.

Note: It is important to make sure

that the control board’s fuse

is functioning. The specs for

the control board fuse are:

5x20mm, 250V, 315mA, fast

acting. For more inormation

on a blown fuse on the

control board, check the

Troubleshooting section of

this document.

Table 6. Maximum wire length for front

desk switch and remote

control connections

External Interface

Wire

Specification

Size Length

Thermostat

#22 100 ft.

#20 200 ft

#18 300 ft.

Energy mgmt system #20 900 ft.

#18 1500 ft.

Remote fan #20 60 ft.

#18 66 ft.

Display module #20 100 ft.

#18 120 ft.

Table 7. Wiring Voltage

Unit Mode

Voltage at terminal Corresponding

Normal

OperationGH GL W Y O

High Heat Pump 24 0 0 24 0 Heat

PTHE Heat Pump

Auxiliary is Electric

only

Low Heat Pump 0 24 0 24 0 Heat

High Emgcy Heat 24 0 24 0 0 Heat

24 0 24 24 0 Electric Heat Only

Low Emgcy Heat 0 24 24 0 0 Heat

0 24 24 24 0 Electric Heat Only

High Cooling 24 0 0 24 24 Cool

Low Cooling 0 24 0 24 24 Cool

High Fan 24 0 0 0 0 Fan Only

Low Fan 0 24 0 0 0 Fan Only

Off 0 0 0 0 0 Off – no capacity

Notes: In the event that none of the

combinations listed in the table above is

present, the input will be deemed invalid and all

heating, cooling, and fan operation will be

disabled.

PTEE Air Conditioner

(Auxiliary is Electric,

Hot Water, or Steam

High Auxiliary Heat 24 0 24 0 X Heat

Low Auxiliary Heat 0 24 24 0 X Heat

High Cooling 24 0 0 24 X Cool

Low Cooling 0 24 0 24 X Cool

High Fan 24 0 0 0 X Fan Only

Low Fan 0 24 0 0 X Fan Only

Off 0 0 0 0 X Off – no capacity

Table 7. Wiring Voltage

Unit Mode

Voltage at terminal Corresponding

Normal

OperationGH GL W Y O

High Heat Pump 24 0 0 24 0 Heat

16 PTAC-SVX01C-EN

Installation

Notes: EN = Enabled - operations based on

other logic

Notes: N/C = No change from prior state

Step 8. Configure the display

module settings

Indoor Temperature setpoint

The indoor temperature setpoint

buttons tell the unit how warm or

cool the occupant wants the room.

The setpoint is set by pressinging the

up/down buttons on the interface

module. These buttons do not scroll

(i.e. holding the button will not

continue to adjust the setpoint value)

because each adjustment of the

setpoint value requires its own

unique button press.

Default setpoint on first power up:

72°F (22.0°C – closest approximation)

Setpoint resolution: ± 1°F (± 0.5°C)

User Mode Selection

Pressing the MODE button on the

unit tells the unit which mode the

occupant prefers. There are four

modes to choose from.

1. COOL

2. HEAT

3. FAN (fan only)

4. OFF (default for first power up)

Table 8. Output settings

User Mode / Model

ID

Fan

High

ID

Fan

Low

Aux

Heat Comp

Rev

Valve

(PTHE)

OD

Fan

Rmt

Fan

Cond

Pump

(PTHE)

Vent

Door

/Fan

High Heat Pump

(PTHE only)

ON OFF OFF ON OF ON EN EN EN

Low Heat Pump

(PTHE only)

OFF ON OFF ON OFF ON EN EN EN

High Emergency/

Auxiliary Heat

ON OFF ON OFF N/C OFF EN EN EN

Low Emergency/

Auxiliary Heat

OFF ON ON OFF N/C OFF EN EN EN

High Cooling ON OFF OFF ON ON ON EN EN EN

Low Cooling OFF ON OFF ON ON ON EN EN EN

High Fan ON OFF OFF OFF N/C OFF EN EN EN

Low Fan OFF ON OFF OFF N/C OFF EN EN EN

Off OFF OFF OFF OFF N/C OFF OFF EN OFF

Fan Speed Selection

Pressing the FAN button on the

interface module determines fan

speed. There are two fan speeds to

choose from.

1. LOW (default for first power up)

2. HIGH

Field commissioning support

Manual Test Mode

A manual test mode is provided to

allow a field technician to verify

proper output and end device

operation through a predetermined,

timed sequence.

Figure 16. Digital display module

Fan Mode

The sequence will automatically

advance through all outputs and exit

when the sequence has completed; it

is left to the technician to monitor the

status of the end devices during the

test to verify that each operates

properly.

Manual test is initiated by combining

the following conditions:

• User Mode = OFF

• Press and hold MODE &

SETPOINT DOWN for 5 seconds

During the test process, the word

"STEP" and the corresponding step

number will be lighted on the

display. After the final step has been

executed, the controller will exit

Manual test and force the controller

to into a reset.

Manual test mode may be cancelled

by pressing any button on the

display.

Manual test is not available if there is

no interface module, as is in Class 2

control applications.

The test sequence attempts to clear

unit diagnostics and restore normal

unit operation prior to testing the

outputs. If the diagnostics remain

after an attempt to clear them,

manual test may be affected or

disallowed.

Dehumidification

The PTAC controller does not directly

measure room humidity.

The PTAC provides dehumidfication

by combining the following actions

in a predefined sequence.

1. The PTAC subcools the room to a

preset state, a dehumidification

offset below the cooling setpoint.

2. The unit will automatically adjust

the fan speed.

3. When incorporating the vent

door option, the controller will

automatically adjust its position.

PTAC-SVX01C-EN 17

Installation

Step 9. Programmable

Settings

The controller has a total of six (7)

parameters that are user-

configurable:

1. Vent Door Configuration

2. Indoor Fan Cycle configuration

3. Temperature Setpoint Limiting

configuration

4. Energy Management Setpoint

Offset configuration

5. Display Units configuration

6. Indoor Temperature Calibration

7. DH Offset

The interface module texts

“SETTING” and “STEP” provide user

feedback when the unit is in the

configuration mode. The number

directly above the word “STEP”

indicates the configuration step that

is being adjusted. The numbers

above the word “SETTING” (XX.x)

indicate the value of the parameter.

In order for the user to access the

configurable parameters, a digital

display module must be present.

The configuration set-up mode is

entered by pressing and holding the

"MODE" and "FAN" buttons

simultaneously for 5 seconds.

Table 9. Set point configuration

Configuration

step Step description

Configuration

setting Setting description

1 Ventilation Enable 0

1 (default)

Ventilation is disabled

Ventilation is enabled

2 Indoor fan cycle

0 (default) Cycle with compressor

continuously, OFF in OFF mode

ON continuously, HIGH in OFF

mode

1

2

3

Tempe ratu r e

Setpoint Limits

0 (default) cool 50 - 90°F, heat 50 - 90°F

1 cool 55 - 90°F, heat 50 - 85°F

2 cool 60 - 90°F, heat 50 - 80°F

3 cool 65 - 90°F, heat 50 - 75°F

4Energy

Management

Default: 10°F (5.5°C)

Range: 0 to 20°F

(0.0 to 10.0°C)

Resolution: 1.0°F

(0.5°C)

5

Display units 0 (default) IP (English)

1SI (Metric)

6Indoor

Tempe ratu r e

Calibration

Default: 0°F (0.0°C)

Range: -9 to 9°F

(-5.0 to 5.0°C)

Resolution: 1.0°F

(0.5°C)

7 DH offset

Default: 1°F (0.5°C)

Range: 0 to 2°F

(0.0 to 1.0°C)

Resolution 1.0°F Value of zero disables DH.

(0.5°C)

18 PTAC-SVX01C-EN

Installation

1. Ventilation Door Function

The power door works based upon

control logic functions. When the unit

is on, the vent door will open to allow

fresh air to be conditioned before

entering the room. When the unit is

off, the door closes to prevent

unconditioned air from entering the

room.

For more information on vent door

function with dehumidificaiton, refer

to the dehumidification chart.

2. Indoor Fan Cycle set up

The indoor fan can be configured to

provide different types of operation

between its OFF and ON (high/low)

states. This setting is adjustable and

does not force the unit to reset.

3. Temperature Setpoint Limiting

set up

The range of temperature control

setpoints can be limited using this

configuration parameter. After the

controller has determined the

desired user setpoint from the

display, the resulting value is

validated against the setpoint limits.

There are four valid combinations of

heating and cooling setpoint limits:

These set point limits apply to both

the occupied and unoccupied

standby, heating and cooling

setpoints. This setting is adjustable

“on-the-fly” and will not force the

unit into a restart condition.

4. Energy Management Setpoint

Offset set up

The range of the Energy

Management System's effect on

setpoints can be adjusted using this

configuration parameter. This

parameter is adjustable "on-the-fly"

and will not force the controller into a

restart condition. The range and

resolution of available selections is

Range: 0°F to 20°F( 0.0°C to 11.0°C)

Resolution: 1.0°F( 0.5°C)

5. Display Unit set up

The user can change the way the

interface module displays

temperature. The symbols °F and °C

will not be present on the display;

however, the range and precision of

the room temperature and setpoint

values will make the selection

obvious.

6. Indoor temperature calibration

The indoor temperature can be

calibrated to match an independent

reading. The adjustment range is +/-

10.0°F (6°C) with a resolution of 1°F

(0.5°C).

7. Dehumidification Offset

The offset defines the point below

the setpoint where the unit will stop

running the compressor. A DH

display module is required to use this

feature.

The PTAC allows the options of 0°F

(disable), 1°F (default) and 2°F

(optional) for the dehumidification

offset. The dehumidification feature

will be disabled when the

configuration of 0°F is selected.

Last User Setpoint, Mode, and

Fan Selections

The controller saves the last inputs

that the user has chosen 5 seconds

after the user has ceased changing

them. These settings will be used

after the next power cycle or

controller reset.

Operation without configuration

The controller tests the configuration

for validity. If the data is corrupted

the controller will revert to default

values for every parameter. A

diagnostic code will be displayed

when using the default values.

Table 10. Display units

Selection

#

Unit of

Measure

Display

Example

0 IP (English) 77 (DEFAULT)

1SI (Metric)24.5

Table 11. Setpoint limiting

Cooling Setpoint Heating Setpoint

Selection

#Low Limit

High

Limit

Low

Limit High Limit

0 50°F 90°F 50°F 90°F (DEFAULT)

1 55°F 90°F 50°F 85°F

2 60°F 90°F 50°F 80°F

3 65°F 90°F 50°F 75°F

PTAC-SVX01C-EN 19

Installation

Energy Management

System

Occupancy States

The controller is designed to handle

two possible occupancy states:

• occupied

• occupied standby

When the Energy Management

System input is present, it is possible

for the controller to switch between

the two occupancy states.

If the EMS input is not connected, the

controller will always assume the

occupied state.

Occupied state

When the controller is in the

occupied state, the unit runs space

comfort control using the occupied

setpoints. All heating/cooling/

ventilation features are enabled.

Table 12. Indoor fan cycle configuration

Config # Indoor Fan Cycle Mode

Indoor fan will not run when the user mode is OFF. (DEFAULT)

0

Indoor fan will cycle to the user selected speed in conjunction with

the compressor or electric heat during HEAT or COOL

Indoor fan will run continuously at the user selected fan speed

during FAN

EMS has no affect.

1

Indoor fan will normally run continuously at the user selected fan

speed.

Indoor fan will not run when the user mode is OFF.

Indoor fan will cycle in conjunction with the compressor or electric

heat when the EMS is enabled.

2

Indoor fan will normally run continuously at the selected fan

speed.

Indoor fan will run at HIGH speed when the user mode is OFF.

Indoor fan will cycle in conjunction with the compressor or electric

heat when the EMS is enabled.

Table 13. Occupancy arbitration for

energy management

EMS Input State

Controller

Occupancy State

Open or Not Present Occupied

Closed Occupied Standby

Occupied Standby state

When the controller is in occupied

standby state, the unit runs space

comfort control using the occupied

standby setpoints. All heating/

cooling/ventilation features are

enabled. Because the occupied

standby setpoints cover a wider

range than the occupied setpoints

the demand for heating and cooling

the space is reduced.

20 PTAC-SVX01C-EN

Installation

Table 14. PTEE manual test sequence

Step

Indoor

Fan High

Indoor

Fan Low

Remote

Fan

Outdoor

Fan

Condensate

Pump Comp

Reversing

Valve Aux. Heat

Ventilation

Door/Fan

Time in

Step

1 All off Off Off Off Off N/A (Off) Off N/A (Off) Off Off 10 sec

2 Fan high On Off Off Off N/A (Off) Off N/A (Off) Off Off 20 sec

3 Fan Low Off On Off Off N/A (Off) Off N/A (Off) Off Off 20 sec

4 Remote

Fan

Off On On Off N/A (Off) Off N/A (Off) Off Off 20 sec

5 Outdoor

Fan

Off On Off On N/A (Off) Off N/A (Off) Off Off 20 sec

6 Compres

sor

Off On Off On N/A (Off) On N/A (Off) Off Off 60 sec

7 Aux Heat Off On Off OnOff N/A (Off) Off N/A (Off) On Off 60 sec

8Vent

Door

Off On Off OnOff N/A (Off) Off N/A (Off) Off On 20 sec

Exit

Table 15. PTHE manual test sequence

Step

Indoor

Fan High

Indoor

Fan Low

Remote

Fan

Outdoor

Fan

Condensate

Pump Comp

Reversing

Valve

Aux

Heat

Ventilation

Door/Fan

Time in

Step

1 All off Off Off Off Off Off Off Off Off Off 10 sec

2 Fan High On Off Off Off Off Off Off Off Off 20 sec

3 Fan Low Off On Off Off Off Off Off Off Off 20 sec

4 Remote Fan Off On On Off Off Off Off Off Off 20 sec

5 Outdoor Fan Off On Off On Off Off Off Off Off 20 sec

6 Condensate

Pump

Off On Off On On1 Off Off Off Off 20 sec

7 Compressor

on Cooling

Off On Off On Off On OffOn Off Off 60 sec

8 Compressor

Off

Off Off On Off On Off Off OffOn Off 60 sec

9 Compressor

on Heating

Off On Off On Off On OnOff Off Off 60 sec

10 Aux Heat Off On Off OnOff Off Off OnOff On Off 60 sec

11 Vent Door Off On Off OnOff Off Off Off Off On 20 sec

Exit

PTAC-SVX01C-EN 21

Sequence of Operation

Automatic 3-minute

Compressor Lockout

After the compressor cycles off, it

will not restart for three minutes.

This feature prevents the

compressor from short cycling and

extends the overall life.

Automatic 2nd Stage Electric

Heat (PTHE only)

If the room temperature falls to 2.5°F

below the setpoint temperature or

the unit compressor fails, the reverse

cycle heat is shut off and the electric

heat is turned on.

Indoor Room Freeze

Protection

When the unit senses room

temperatures of 40°F or below, the

unit activates the indoor fan motor

and either the electric resistance

heater or the hydronic heater to help

prevent pipes or fixtures from

freezing.

This also overrides the Energy

Management System input for unit

mounted or wall mounted display

modules

Random Restart Function

This function allows random restart

of the PTAC units in the event of a

power outage. The restart delay

reduces the initial inrush current

from the building to help prevent a

second power outage caused by too

much current draw.

The random restart function will

occur after every power up cycle by

delaying the operation of the unit for

0 to 90 seconds. Compressor

minimum off time is enforced after

the random restart function has

completed.

Door Switch Occupancy

Sensor

The PTAC can accommodate a field-

installed door switch and occupancy

sensor to operate the energy

management feature.

Remote Thermostat Control

Each unit can be operated from any

standard 4 or 5-wire, remote-

mounted thermostat. Also, the unit

has a built-in low voltage power

source that can accommodate either

a manual, auto changeover, or

programmable thermostat.

Setpoint Limiting

The setpoint limiting feature reduces

energy costs by controlling the

maximum setpoint in heating and

the minimum setpoint in cooling.

Active Defrost (PTHEs only)

PTACs have an active defrost system

that removes ice build-up on the

outdoor coil, which may occur

during the heat pump cycle.

Remote Thermostat

Operation

The GL, GH, O, W, Y, R, and C

terminals provide control inputs for a

remote wall-mounted thermostat.

The terminals listed control the

operation of the unit when no

display module is used. A display

module will take precedence over

any of these inputs.

Mode Button Operation

OFF - cooling and heating functions

stop.

HEAT - room temperature is

maintained by cycling in heat pump

mode or electric heat. The model

PTHE switches from heat pump

mode to electric heat when the

outdoor air temperature is below

20°F (approximately), or when the

heat pump cannot keep up with the

heating load when using a two-stage

thermostat.

COOL - room temperature is

maintained by cycling the air

conditioner.

FAN - the fan runs at the user

selected speed or runs as otherwise

configured.

Fan Operation

The fan speed may be user selected

as either high or low. Fan cycling

versus continuous is operation

configurable. See section on

configuration for details.

Front Desk Control (FD1, FD2

Inputs)

The energy management input is

used to move the setpoint up in the

case of cooling and down in the case

of heating. This conserves energy

by reducing the demand in the

space.

The energy management input is a

dry contact closure; typically this is

driven from either a occupancy

sensor or a front desk control

system.

Figure 17. Digital display module

Fan Mode

Operation

22 PTAC-SVX01C-EN

Operation

Notes:

1. Connection to R enables input functions W, Y,

GL, GH, O,VT, and/or EN.

2. Connect 24VAC, 3VA maximum Remote Fan

Control Relay to RF and C

Remote Fan Operation

PTACs can operate a remote fan to

provide conditioned air to additional

rooms or areas that are not well

ventilated. The remote fan operates

any time the PTAC indoor fan is

operating.

The remote fan requires a 24 VAC, 3

VA maximum relay that connects to

the control board RF and C terminal

user inputs. The relay and remote fan

are field supplied. Refer to the wiring

diagrams section for wiring details.

Vent Control

Vent control draws fresh air into the

conditioned area to provide

ventilation when the indoor fan is

operating. However, this may

increase heating cooling loads and

operating costs.

To obtain access to the vent control,

remove the cabinet front and locate

the vent control lever on the left side

of the chassis. Push the vent control

lever up to open the vent or down to

close.

The unit ships with the vent door

closed and secured by a screw.

Table 16. User inputs

Input Function

TB1

+Remote display

communications link (+)

-Remote display

communications link (-)

TB2

EN Energy management

system input

VT Ventilation input

O Reversing valve (class 2

thermostat)

GL Low fan speed (class 2

thermostat)

GH High speed fan (class 2

thermostat)

Y Cool (class 2 thermostat)

W Heat (class 2 thermostat)

R 24VAC common1

C Ground2

RF Remote fan relay output

CAUTION

Freezing Temperatures!

Do not allow liquid refrigerant to

contact skin. If it does, treat the

injury similar to frostbite. Slowly

warm the affected area with

lukewarm water and seek immediate

medical attention. Direct contact

with liquid refrigerant may cause

minor or moderate injury.

Air Discharge Grille

The discharge grille can be adjusted

to expel air at either a 15° or 40° (40°

default) angle. Figure 18.

To change the discharge air airflow

angle:

1. Remove the front cabinet.

2. Position the front cabinet so that

the backside is accessible.

3. Remove the four screws which

secure the discharge air grille to

the cabinet front with a phillips-

head screwdriver. See Figure 31.

4. Rotate the grille 180° end-for-

end.

5. Reinstall the screws securing the

discharge air grille to the cabinet

front. Reinstall the cabinet front

on the unit.

Figure 18. Discharge air grille

Screws

PTAC-SVX01C-EN 23

Operation

Notes: Certified in accordance with the Unitary Air-Conditioner Equipment Certification Program, which is based on ARI Standard 310/380.

Table 17. Air conditioner performance data

PTEE 07 PTEE 09 PTEE 12 PTEE 15

Voltage (V) 115 208 230 265 115 208 230 265 115 208 230 265 208 230 265

Cooling data

Cooling

capacity

(Btu/H)

7,200 6,800 7,000 7,300 9,300 8,800 9,000 8,700 12,000 11,600 11,800 11,800 13,700 13,900 14,400

Cooling amps

(A)

5.3 2.9 2.7 2.4 7.3 3.9 3.6 3.1 9.7 5.1 4.8 4.1 6.9 6.4 5.7

EER (Btu/H/

watt)

12.2 12.0 12.0 12.0 11.5 11.4 11.4 11.3 11.2 11.2 11.2 11.3 10.0 10.0 9.8

Moisture

removal

(Pts/h)

1.8 2.1 2.1 2.1 2.2 2.5 2.6 2.6 3.0 3.1 3.1 3.1 4.1 4.1 4.1

Heat pump

heating data

Heating

capacity

(Btu/H) ***** * * * * * * ****

Heating amps

(A)

***** * * * * * * ****

Heating power

(W)

***** * * * * * * ****

COP (W/W) ***** * * * * * * ****

Airflow

Indoor cfm

(wet)

@0.3 esp (hi) 280 225 256 256 325 225 256 256 350 295 325 325 320 350 350

Indoor cfm

(wet)

@0.3 esp (lo) 250 191 225 225 294 191 225 225 320 266 294 294 290 320 320

Indoor cfm

(dry)

@0.3 esp (hi) 312 260 290 290 350 260 290 290 400 320 350 350 365 400 400

Indoor cfm

(dry)

@0.3 esp (lo) 280 235 266 266 323 235 266 266 360 293 323 323 330 360 360

Electric heat

data

Heater size

(kW)

208V *1.6 2.4 * * 1.6 2.4 4.0 *1.6 2.4 4.0 1.6 2.4 4.0

230V *2.0 3.0 * * 2.0 3.0 5.0 *2.0 3.0 5.0 2.0 3.0 5.0

265V *2.0 3.0 * * 2.0 3.0 5.0 *2.0 3.0 5.0 2.0 3.0 5.0

Btu/H

208V *5,500 8,200 * * 5,500 8,200 13,700 *5,500 8,200 13,700 5,500 8,200 13,700

230V *6,800 10,200 * * 6,800 10,200 17,100 *6,800 10,200 17,100 6,800 10,200 17,100

265V *6,800 10,200 * * 6,800 10,200 17,100 *6,800 10,200 17,100 6,800 10,200 17,100

Heating watt

208V *1,600 2,400 * * 1,600 2,400 4,000 *1,600 2,400 4,000 1,600 2,400 4,000

230V *2,000 3,000 * * 2,000 3,000 5,000 *2,000 3,000 5,000 2,000 3,000 5,000

265V *2,000 3,000 * * 2,000 3,000 5,000 *2,000 3,000 5,000 2,000 3,000 5,000

Heating amps

208V *7.9 11.8 * * 7.9 11.8 19.7 *7.9 11.8 19.7 7.9 11.8 19.7

230V *8.9 13.4 * * 8.9 13.4 22.2 *8.9 13.4 22.2 8.9 13.4 22.2

265V *7.7 11.6 * * 7.7 11.6 19.3 *7.7 11.6 19.3 7.7 11.6 19.3

24 PTAC-SVX01C-EN

Operation

Notes: Certified in accordance with the Unitary Air-Conditioner Equipment Certification Program, which is based on ARI Standard 310/380.

Notes: Shaded area is rating ampere

Table 18. Heat pump performance

PTHE 07 PTHE 09 PTHE 12 PTHE 15

Voltage (V) 208 230 265 208 230 265 208 230 265 208 230 265

Cooling data

Cooling

capacity(Btu/H)

7,200 7,400 7,200 8,900 9,100 8,700 11,700 12,000 11,700 13,300 13,600 13,600

Cooling amps

(A)

2.9 2.7 2.3 3.9 3.7 3.1 5.1 4.8 4.2 6.8 6.3 5.5

EER(Btu/H watt) 12.0 12.0 12.0 11.4 11.4 10.8 11.2 11.2 11.0 9.9 9.9 9.9

Moisture

removal (Pts/h)

2.1 2.1 2.1 2.5 2.6 2.6 3.0 3.1 3.1 4.1 4.1 4.1

Heat pump

heating data

Heating capacity

(Btu/H)

5,900 6,100 6,100 7,600 7,800 7,300 9,900 10,100 10,100 12,200 12,500 12,500

Heating amps

(A)

2.6 2.5 2.1 3.4 3.2 2.6 4.3 4.0 3.5 5.8 5.4 4.7

Heating power

(W)

540 560 560 695 715 715 935 955 925 1230 1260 1260

COP (W/W) 3.2 3.2 3.2 3.2 3.2 3.0 3.1 3.1 3.2 2.9 2.9 2.9

Airflow

Indoor cfm (wet)

@0.3 esp (hi)

225 256 256 225 256 256 295 325 325 320 350 350

Indoor cfm (wet)

@0.3 esp (lo)

191 225 225 191 225 225 266 294 294 290 320 320

Indoor cfm (dry)

@0.3 esp (hi)

260 290 290 260 290 290 320 350 350 365 400 400

Indoor cfm (dry)

@0.3 esp (lo)

235 266 266 235 266 266 293 323 323 330 360 360

Electric heat

data

Heater size

(kW)

208V 1.6 2.4 *1.62.44.0 1.6 2.4 4.0 1.6 2.4 4.0

230V 2.0 3.0 *2.03.05.0 2.0 3.0 5.0 2.0 3.0 5.0

265V 2.0 3.0 *2.03.05.0 2.0 3.0 5.0 2.0 3.0 5.0

Btu/H

208V 5,500 8,200 * 5,500 8,200 13,700 5,500 8,200 13,700 5,500 8,200 13,700

230V 6,800 10,200 * 6,800 10,200 17,100 6,800 10,200 17,100 6,800 10,200 17,100

265V 6,800 10,200 * 6,800 10,200 17,100 6,800 10,200 17,100 6,800 10,200 17,100

Heating watt

208V 1,600 2,400 * 1,600 2,400 4,000 1,600 2,400 4,000 1,600 2,400 4,000

230V 2,000 3,000 * 2,000 3,000 5,000 2,000 3,000 5,000 2,000 3,000 5,000

265V 2,000 3,000 * 2,000 3,000 5,000 2,000 3,000 5,000 2,000 3,000 5,000

Heating amps

208V 7.9 11.8 * 7.9 11.8 19.7 7.9 11.8 19.7 7.9 11.8 19.7

230V 8.9 13.4 * 8.9 13.4 22.2 8.9 13.4 22.2 8.9 13.4 22.2

265V 7.7 11.6 * 7.7 11.6 19.3 7.7 11.6 19.3 7.7 11.6 19.3

PTAC-SVX01C-EN 25

Operation

Table 19. Cooling temperature change - air conditioners

Room

air dry

bulb

Room air wet

bulb

PTEE0701 PTEE0702 PTEE0901 PTEE0902 PTEE1201 PTEE1202 PTEE1501 PTEE1502

Temperature across

indoor coil (∆ T)

Temperature across

indoor coil (∆ T)

Temperature across

indoor coil (∆ T)

Temperature across

indoor coil (∆ T)

MinMaxMinMaxMinMaxMinMax

Rating Btu/H 7200 7600 8800 9000 11700 12000 14100 14300

Rating cfm 230 260 240 270 300 330 315 355

90

85 13261514

80 8 1311149 138 12

75 19 22 19 22 18 22 16 20

70 30 33 28 30 26 30 25 27

85

80 4 9 7 11 5 10 5 8

75 14 19 15 18 13 18 12 16

70 23 27 23 25 21 25 20 23

65 34 36 31 33 29 33 28 30

80

75 9 1411149 138 12

70 18 21 18 20 15 20 15 18

65 26 29 24 27 23 26 21 24

60 35 36 32 33 29 33 29 30

75

70 12 16 13 16 10 15 10 14

65 18 22 18 21 15 20 15 19

60 25 28 23 26 21 25 20 24

55 31 34 28 31 26 30 26 28

70

65 12 15 12 14 9 13 9 13

60 17 20 16 18 13 17 13 17

55 22 24 20 22 18 21 17 21

Table 20. Cooling temperature change - heat pumps

Room

airdry

bulb

Room air wet

bulb

PTHE0701 PTHE0702 PTHE0901 PTHE0902 PTHE1201 PTHE1202 PTHE1501 PTHE1502

Temperature across

indoor coil (∆ T)

Temperature

acrossndoor coil (∆ T)

Temperature across

indoor coil (∆ T)

Temperature across

indoor coil (∆ T)

Min Max Min Max Min Max Min Max

rating Btu/H 7300 7600 9000 9300 11800 12000 14000 14600

rating cfm 195 225 240 270 315 355 315 355

90

85 1 3 2 6 1 5 1 4

80 8 13 11 1510138 12

75 19 22 19 22 18 22 17 20

70 30 33 29 30 26 30 25 28

85

80 4 9 7 11 5 10 5 9

75 14 19 15 18 14 18 12 16

70 23 27 23 25 21 25 21 23

65 33 36 31 33 30 33 28 31

80

75 9 14 11 1510138 12

70 18 21 18 20 16 20 16 18

65 26 29 24 27 23 26 22 25

60 35 36 32 33 30 33 29 31

26 PTAC-SVX01C-EN

Operation

Notes: Shaded area is rating ampere

75

70 12 16 13 16 11 15 10 14

65 18 22 18 21 16 20 16 19

60 24 28 23 26 21 25 21 24

55 31 34 29 31 26 30 26 29

70

65 12 15 12 15 10 13 9 13

60 17 20 16 18 14 17 13 17

55 22 24 20 22 18 21 18 21

Table 21. Cooling amperage — air conditioners

Condenser

inlet air

temp.

PTEE0701 PTEE0702 PTEE0901 PTEE0902 PTEE1201 PTEE1202 PTEE1501 PTEE1502

Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max

2.6 2.9 2.4 2.4 3.6 3.9 3.2 3.2 4.8 5.2 4.2 4.2 6.5 7.1 5.7 5.7

100 2.6 2.9 2.4 2.6 3.4 4.0 2.9 3.1 5.6 5.6 3.9 4.3 6.6 8.0 5.6 6.2

95 2.4 2.8 2.3 2.5 3.2 3.8 2.7 3.0 5.4 5.3 3.7 4.1 6.2 7.6 5.3 5.9

90 2.3 2.7 2.2 2.4 3.1 3.6 2.6 2.9 5.2 5.1 3.6 3.9 5.9 7.2 5.1 5.6

85 2.2 2.6 2.1 2.3 2.9 3.4 2.5 2.7 4.9 4.8 3.4 3.8 5.6 6.8 4.8 5.3

80 2.1 2.4 2.0 2.2 2.8 3.3 2.3 2.6 4.7 4.6 3.2 3.6 5.3 6.4 4.6 5.1

Table 22. Cooling amperage — heat pumps

Condenser

inlet air

temp.

PTHE0701 PTHE0702 PTHE0901 PTHE0902 PTHE1201 PTHE1202 PTHE1501 PTHE1502

Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max

2.6 2.9 2.4 2.4 3.6 3.9 3.2 3.2 4.8 5.2 4.2 4.2 6.5 7.1 6.3 6.3

100 2.6 2.9 2.5 2.7 3.4 4.0 3.0 3.2 5.6 5.5 4.1 4.5 6.6 8.0 5.5 6.8

95 2.4 2.8 2.4 2.6 3.2 3.8 2.8 3.1 5.3 5.2 3.9 4.3 6.2 7.6 5.2 5.8

90 2.3 2.6 2.2 2.5 3.1 3.6 2.7 3.0 5.0 5.0 3.7 4.1 5.9 7.2 5.0 5.5

85 2.1 2.5 2.1 2.3 3.1 3.4 2.6 2.9 4.8 4.7 3.5 3.9 5.6 6.8 4.7 5.2

80 2.1 2.3 2.1 2.2 2.9 3.3 2.5 2.7 4.6 4.5 3.3 3.7 5.3 6.4 4.5 4.9

Table 20. Cooling temperature change - heat pumps (continued)

Room

airdry

bulb

Room air wet

bulb

PTHE0701 PTHE0702 PTHE0901 PTHE0902 PTHE1201 PTHE1202 PTHE1501 PTHE1502

Temperature across

indoor coil (∆ T)

Temperature

acrossndoor coil (∆ T)

Temperature across

indoor coil (∆ T)

Temperature across

indoor coil (∆ T)

Min Max Min Max Min Max Min Max

PTAC-SVX01C-EN 27

Operation

Notes: Shaded area is rating wattage

Table 23. Heating total wattage input — heat pumps

Outside air

dry-bulb

Room air

dry-bulb

PTHE

0701

PTHE

0702

PTHE

0901

PTHE

0902

PTHE

1201

PTHE

1202

PTHE

1501

PTHE

1502

Min Max Min Max Min Max Min Max

520 535 670 685 940 965 1210 1235

50

85 580 620 745 790 1030 1115 1295 1435

80 565 600 725 775 1010 1095 1275 1410

75 550 590 710 760 990 1075 1245 1385

70 535 575 695 740 970 1050 1225 1360

65 520 560 675 720 945 1025 1200 1335

45

85 565 600 710 760 1000 1080 1240 1375

80 550 590 695 740 975 1060 1214 1355

75 630 570 680 730 955 1040 1190 1330

70 515 555 660 710 930 1010 1160 1305

65 500 540 640 690 910 995 1145 1280

40

85 545 580 680 725 950 1040 1185 1320

80 530 570 660 710 940 1020 1160 1300

75 515 555 640 690 920 1000 1135 1270

70 500 535 630 675 895 980 1110 1250

65 480 520 610 675 875 955 1090 1220

35

85 525 565 650 695 925 1010 1130 1270

80 510 550 630 675 900 985 1110 1240

75 500 535 610 655 880 965 1080 1220

70 480 520 600 645 855 940 1060 1190

65 465 500 580 625 940 922 1030 1265

Table 24. Heat pump reverse cycle heating capacity

PTEE07 PTEE09 PTEE12 PTEE15

Voltage 208 230 265 208 230 265 208 230 265 208 230 265

Amps 2.5 2.4 2.4 3.4 3.2 2.6 4.3 4.0 3.5 5.7 5.3 4.6

Btu/H 6400 6600 6600 7600 7800 8000 10100 10300 10300 12800 13100 13100

COP 3.6 3.6 3.6 3.2 3.2 3.4 3.3 3.3 3.3 3.0 3.0 3.0

Cfm (dry) 220 230 250 240 270 270 330 360 350 350 390 380

Heating

Btu/H

Outdoor

Ambient

62 7200 7400 7400 9600 9700 9700 12800 13000 13000 15700 15800 15800

57 6900 7100 7100 9300 9600 9600 12500 12800 12800 15000 15200 15200

52 6500 6700 6700 8700 9000 9000 11700 12000 12000 14200 14400 14400

Rating

Point

47 6200 6400 6400 8200 8400 8400 10900 11200 11200 13300 13500 13500

42 5900 6100 6100 7700 7900 7900 10200 10500 10500 12500 12700 12700

37 5600 5800 5800 7200 7400 7400 9500 9700 9700 11700 11900 11900

32 5300 5500 5500 6700 6900 6900 9600 8900 8900 10800 11000 11000

27 5000 5200 5200 6200 6300 6300 7900 8200 8200 10000 10200 10200

24 4800 5000 5000 5800 6000 6000 7500 7800 7800 9500 9700 9700

28 PTAC-SVX01C-EN

Operation

Table 25. Unit accessory model numbers

Description Part Number

Architectural Grilles

ARCHITECTURAL ALUMINUM GRILLE BAYAAGL001

ARCHITECTURAL ALUMINUM GRILLE -DARK

BRONZE

BAYAAGL002

ARCHITECTURAL ALUMINUM GRILLE - SOFT

DOVE

BAYAAGL003

ARCHITECTURAL ALUMINUM GRILLE - SPECIAL

COLOR

BAYAAGL004

Circuit breakers

CIRCUIT BREAKER - 208/230 15AMP BAYCBKR001

CIRCUIT BREAKER 208/230 20AMP BAYCBKR002

CIRCUIT BREAKER - 208/230 30AMP BAYCBKR003

Condensate pump

CONDENSATE PUMP 208/230 BAYCPMP001

CONDENSATE PUMP 265 BAYCPMP002

Drain Kit

DRAIN KIT BAYDRAN001

Filters

SPARE FILTERS 10 PACK BAYFLTR009

Hard Wire Kit

HARD WIRE KIT BAYHWRK001

Leveling Legs

LEVELING LEG BAYLVLG001

Power Switch(1)

POWER SWITCH -115V, 208/230V 265V 30 AMP BAYPSW002

Stamped grille

STAMPED ALUMINUM GRILLE - SINGLE PACK BAYSAG001

STAMPED ALUMINUM GRILLE - TEN PACK BAYSAG002

Wall Sleeve

13 INCH WALL SLEEVE BAYWSLV001

18 INCH WALL SLEEVE BAYWSLV002

24 INCH WALL SLEEVE BAYWSLV003

Power Cord

UNIVERSAL POWER CORD 115 VOLT

- 15 Amp BAYPCRD007

UNIVERSAL POWER CORD 230 VOLT - 15 AMP BAYPCRD001

UNIVERSAL POWER CORD 230 VOLT - 20 AMP BAYPCRD002

UNIVERSAL POWER CORD 230 VOLT - 30 AMP BAYPCRD003

UNIVERSAL POWER CORD 265 VOLT - 15 AMP BAYPCRD004

UNIVERSAL POWER CORD 265 VOLT - 20 AMP BAYPCRD005

UNIVERSAL POWER CORD 265 VOLT - 30 AMP BAYPCRD006

Display Module

DISPLAY MODULE (AMERICAN STANDARD LOGO

STANDARD)

BAYAMDM001

DISPLAY MODULE (AMERICAN STANDARD LOGO

& DEHUMIDIFICATION)

BAYAMDM002

DISPLAY MODULE (TRANE LOGO STANDARD) BAYTRDM001

DISPLAY MODULE (TRANE LOGO &

DEHUMIDIFICATION)

BAYTRDM002

Escutcheon Cover(2)

ESCUTCHEON COVER FOR FRONT PANEL

(AMSTD LOGO)

BAYACVR001

ESCUTCHEON COVER FOR FRONT PANEL

(TRANE LOGO)

BAYTCVR001

Plastic Front Cover(3)

PLASTIC FRONT COVER FOR PTAC BAYPCVR001

Connector for Hardwire(4)

CONNECTOR FOR HARDWIRE KIT 208/230V -

15 AMP

BAYCNHK011

CONNECTOR FOR HARDWIRE KIT 208/230V -

20 AMP

BAYCNHK012

CONNECTOR FOR HARDWIRE KIT 208/230V -

30 AMP

BAYCNHK013

CONNECTOR FOR HARDWIRE KIT 265V - 15

AMP

BAYCNHK021

CONNECTOR FOR HARDWIRE KIT 265V - 20

AMP

BAYCNHK021

CONNECTOR FOR HARDWIRE KIT 265V - 30

AMP

BAYCNHK023

CONNECTOR FOR HARDWIRE KIT 115V - 15

AMP

BAYCNHK031

Subbase(5) (6)

UNIVERSAL SUBBASE BAYSUB001

SOCKET FOR SUBBASE 208/230 20 AMP BAYSCKT001

SOCKET FOR SUBBASE 208/230 30 AMP BAYSCKT002

SOCKET FOR SUBBASE 265 20 AMP BAYSCKT003

SOCKET FOR SUBBASE 265 30AMP BAYSCKT004

(1) The power switch can be installed on the hard wire junction box and

provides a way to shut on and off the PTAC unit. It is an optional ac-

cessory when using the power cord to power the PTAC unit. Check local

codes for approval

(2) This escutcheon cover should be ordered whenever the display module

is wall mounted or a thermostat or third party provider unit controls are

ordered. This escutcheon includes a control cover plate that covers the

normal unit mounted nomenclature. It comes 5 pieces per pack.

(3) All hydronic PTAC chassis come standard without a plastic front cover.

If a unit is required to work without heat and without a hydronic kit the

plastic front cover should be ordered.

(4) Not required when using a Hard Wire Kit.

(5) Provides a space to tie into a building’s wiring with a receptacle to plug

the unit into. It gives additional leveling and support capabilities and

provides a place for fuses, a circuit breaker or a mechanical disconnect

to be mounted. (30A is for units with 5kW electric heat, 20A for 3kW or

less electric heat.)

(6) All subbases require a socket. For 15 and 20 amp, the 20amp socket

can be used on either the 208/230V or the 265V.

Table 25. Unit accessory model numbers

Description Part Number

PTAC-SVX01C-EN 29

Operation

Table 26. Hydronic heat options

Kit Description

HHydronic

Coil Type

WWater Coil

SSteam Coil

Accessory Type

KKit

Power Voltage

01 208-230 VAC

02 265 VAC

04 115 VAC

Coil Positioning

L Left hand hot water coil

connection (Standard/

Stocked)

R Right hand hot water coil

connection (Not Stocked)

Kick Plate

S Standard 2" to 6" adjustable

kick plate

E Extended standard base kick

plate 7" to 13"

M Upgraded kick plate standard

height 2" to 6" (Like the unit

ventilator design)

U Upgraded kick plate extended

height 7" to 13" (Like the unit

ventilator design)

Color

S Standard Soft Dove II

C Special Color

30 PTAC-SVX01C-EN

Maintenance Procedures

Perform the following maintenance

procedures to ensure proper unit

operation.

WARNING

Live Electrical Components!

During installation, testing, servicing

and troubleshooting of this product,

it may be necessary to work with

live electrical components. Have a

qualified licensed electrician or other

individual who has been properly

trained in handling live electrical

components perform these tasks.

Failure to follow all electrical safety

precautions when exposed to live

electrical components could result in

death or serious injury.

WARNING

Hazardous Voltage!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

Chassis

Clean the chassis every four months

or more often as the atmospheric

conditions require. Use water and

detergent to clean the basepan,

center partition and coils.

Using harsh cleaning materials may

cause a deterioration of the coil fins

or end plates.

Do not use a high pressure cleaner

as it could cause severe damage to

the PTAC fins and coils.

Note: It is very important to not get

any of the electronic parts

wet.

A hose is okay to use to clean the

coils, but make sure to cover the

control with a blanket or plastic bag

to prevent it from getting wet.

Wall Sleeve

Clean the wall sleeve every four

months or more often as the

atmospheric conditions require.

Remove any debris from the bottom

of the panel, and from around any

internal or external drain kit

accessory item prior to using water

or detergent. This will ensure that no

debris clogs up the drain holes.

The use of harsh cleaning materials

may cause a deterioration of the

bottom panel over time. Do not use

a high pressure cleaner because it

could spray the side or top panel

insulation material and cause future

air quality problems like mold and

mildew.

Clean side and top panel insulation

material with a lint brush or piece of

tape. Press tape against insulation

lightly and slowly peel away to

remove dirt and debris.

Compressor/Fan Motor

The compressor and fan motor are

hermetically sealed, permanently

lubricated, and require no additional

oiling.

Cabinet Front

The cabinet front and discharge air

grille can be cleaned with a mild

soap or detergent.

Under NO circumstances should

hydrocarbon based cleaners (e.g.

acetone, benzene, naphtha gasoline,

etc.) be used to clean the front or air

grilles.

Use care when cleaning the control

area. Do not use an excessively wet

cleaning cloth.

Intake Air Filter

The intake air filter and vent door

filter are both constructed of durable

polypropylene. Clean filters monthly

to ensure proper unit operation.

The fan must be off before the filters

are cleaned.

To remove the air filters, grasp the

top of the filter and lift out of the

front cabinet (Figure 19.) Reverse the

procedure to reinstall the filters.

Vent Filter

Before cleaning the vent filter,

disconnect power to the unit by

unplugging the power cord at the

wall outlet or subbase, or disconnect

power at the fuse box or circuit

breaker. If unit is operated with vent

door closed, the vent filter does not

need to be cleaned.

1. Remove the cabinet front as

described in front removal.

2. Remove the six screws securing

the chassis to the wall sleeve

with a Phillips-Head screwdriver.

3. Slide the chassis out of the wall

sleeve far enough so that the

vent filter is accessible as shown

in Figure 20.

4. Remove the vent filter by

unscrewing the two screws at

the top of the filter and gently

pulling the filter away from the

partition panel. Refer to

Figure 21. The filter can be

cleaned by running under a low

pressure hose or sink faucet.

Figure 19. Intake air filter removal

is through top of unit. Inspect and

clean filters monthly for proper unit

operation.

Maintenance

PTAC-SVX01C-EN 31

Maintenance

5. Reinstall the filter by reattaching

the hook to the bottom of the

vent door and replacing the two

screws, slide the chassis back

into the wall sleeve, secure it in

place with six screws and

reinstall the front cabinet.

Scheduled Maintenance

To achieve top performance and high

efficiency, a cleaning/ inspection

schedule must be established for this

unit. Maintaining this schedule can

be accomplished by either a local

maintenance staff or an authorized

servicer and must follow the

instructions described in this manual.

• If the unit is operated in a dusty

climate, dust may collect in the

basepan and clog the condenser

coil. It is advisable to remove the

unit from the sleeve and

thoroughly clean the basepan

and condenser coil on a periodic

basis.

Figure 20. Vent (left side of unit)

Figure 21. Vent filter removal

Vent door

• If the unit is installed ocean side

or in a corrosive atmosphere, its

life may be greatly reduced by

the corrosive environment.

Under these conditions the unit

should be removed from the

sleeve and completely cleaned at

least four times per year. At that

time any scratches or blisters on

the painted surfaces should be

sanded and repainted.

Refrigeration System

Service

WARNING

Ensure Terminal Cover is in

Place!

Do not plug in this product or apply

power to the compressor if the

compressor terminal cover is

removed or is not firmly in place.

Failure to follow these instructions

could result in a fire that could cause

death, personal injury, or property

damage.

Service operations requiring opening

of the hermetically sealed

refrigeration system should be taken

to a well equipped shop where

special equipment for evacuating,

dehydrating, charging and testing is

available. The following equipment is

necessary:

• Nitrogen of no more than 0.0012

grains of moisture.

• Vacuum pump capable of

evacuating to a minimum of 50

microns.

• Micron gauge to check vacuum

• Refrigerant charging cylinder

accurate to within 1/4 oz.

• Electronic leak detector

• Electrical equipment to test

compressors, capacitors, voltage

relays, and overload protectors

• Voltmeter, ammeter, and

wattmeter

• Silver soldering and brazing

equipment - Pinch off tools ¼ in

to 5/8 in

• Thermocouple tester

WARNING

Hazardous Pressures!

If a heat source is required to raise

the tank pressure during removal of

refrigerant from cylinders, use only

warm water or heat blankets to raise

the tank temperature. Do not exceed

a temperature of 150°F. Do not, under

any circumstances apply direct flame

to any portion of the cylinder. Failure

to follow these safety precautions

could result in a violent explosion,

which could result in death or

serious injury.

CAUTION

Freezing Temperatures!

Do not allow liquid refrigerant to

contact skin. If it does, treat the

injury similar to frostbite. Slowly

warm the affected area with

lukewarm water and seek immediate

medical attention. Direct contact

with liquid refrigerant may cause

minor or moderate injury.

Dehydrating and Evacuating

Refrigeration System

A rather popular misconception

exists that since air conditioners

normally operate with a refrigerant

temperature above 32°F, moisture in

the system is harmless. Nothing

could be further from the truth.

Oxygen from moisture plus normal

compressor and motor heat reacts

chemically with the refrigerant and

oil to form corrosive hydrochloric

and hydrofluoric acids. These acids

contribute to the break down of

motor winding insulation and the

corrosion of compressor working

parts and cause unnecessary

compressor failure.

Sludge, which is a residue of the

chemical reaction, coats all

compressor parts, the inside of

refrigerant tubing, and may even

restrict refrigerant flow through the

capillary tube(s).

32 PTAC-SVX01C-EN

Maintenance

Leak Testing

Refrigerant leaks are best detected

with a halide or electronic leak

detector.

WARNING

Use of Pressure Regulator –

Valves – Gauges!

Always use pressure regulators,

valves, and gauges to control drum

and line pressures when pressure

testing equipment. Failure to follow

these instructions could result in an

explosion causing death, serious

injury, or equipment damage.

WARNING

Leak Testing!

Do not exceed 200 psig when leak

testing system. Failure to follow

these instructions could result in an

explosion causing death or serious

injury.

The importance of careful leak

testing cannot be over emphasized.

Undetected leaks invariably lead to

repeated calls and eventually result

in system contamination, restrictions

and burned out compressors.

For a system that contains a

refrigerant charge and is suspected

of having a leak, stop the operation,

check all tubing and fittings. Soap

suds may also be used.

Note: The flame of the halide

detector will glow green in

the presence of R22

refrigerant.

If a leak is detected, do not attempt to

apply more brazing material to the

joint. Recover the charge, unbraze the

joint, clean and rebraze.

For a system that has been newly

repaired and does not contain a

charge, connect a cylinder of

refrigerant, through a gauge

manifold, to the process tube of the

compressor and liquid line strainer.

Open the valve on the cylinder and

manifold and allow the pressure to

build up within the system. Check for

and handle leaks as described above.

After the test has been completed,

recover the test charge, evacuate the

system, and recharge with clean

refrigerant.

Brazing

WARNING

Hazard of Explosion!

Use only dry nitrogen with a

pressure regulator for pressurizing

unit. Do not use acetylene, oxygen or

compressed air or mixtures

containing them for pressure testing.

Do not use mixtures of a hydrogen

containing refrigerant and air above

atmospheric pressure for pressure

testing as they may become

flammable and could result in an

explosion. Refrigerant, when used as

a trace gas should only be mixed

with dry nitrogen for pressurizing

units. Failure to follow these

recommendations could result in

death or serious injury or equipment

or property-only damage.

CAUTION

High Temperatures!

Brazing requires high temperatures.

Direct contact with hot surfaces may

cause minor or moderate injury.

Satisfactory brazing results require

cleanliness, experience and the use

of proper material and equipment.

Verify brazing connections are

properly sized, free of rough edges,

and clean.

Use of these generally accepted

brazing materials:

• SIL-FOS (Alloy of 15% silver, 80%

copper, 5% phosphorus): use

without flux on copper to copper.

Note: DO NOT USE FOR A COPPER

TO STEEL CONNECTION.

Recommended heat is

approximately 1400°F.

• SILVER SOLDER (Alloy of 30%

silver, 38% copper, 32% zinc): use

with fluoride base flux on copper

to steel, brass to copper, steel to

steel, or brass to steel.

Recommended heat is

approximately 1200°F.

PTAC-SVX01C-EN 33

Maintenance

Figure 22. Refrigeration sealed system — heat pump (air conditioning

model

Figure 23. Refrigeration sealed system — Heat pump (heat pump model)

Evacuation CAUTION

Fan Motor Overheat!

Never test operation without the

unit in the wall sleeve. A serious

change in design specifications for

air movement through the

evaporator and condenser

compartments, causing the fan

motor to over heat and the

refrigeration system to become

unbalanced will occur when the unit

is not installed in the wall sleeve.

CAUTION

High Temperatures!

Do not allow sludge or oil to contact

skin when evacuating refrigerant

from equipment. Direct contact with

sludge or oil may cause minor or

moderate injury.

Thoroughly evacuate the system

using a high vacuum pump, capable

of producing a vacuum equivalent to

50 microns and a thermocouple

vacuum gauge to give a true reading

of the vacuum in the system.

Note: Never use the system

compressor as a vacuum

pump or run when under a

high vacuum. Motor damage

could occur.

Evacuation Procedure

1. Connect the vacuum pump,

vacuum tight manifold set with

high vacuum hoses,

thermocouple vacuum gauge,

and charging cylinder.

2. Connect the low side line to the

process tube of the compressor.

3. Connect the high side line to the

process tube of the liquid line

strainer.

Note: If either process tube is not

long enough to receive the

compression or flare fitting

and still leave room for a

pinch-off, swag the tube and

braze in an extra length of

tubing.

34 PTAC-SVX01C-EN

Maintenance

4. Start the vacuum pump and

open the shut-off valve to the

high vacuum gauge manifold

only. After the compound gauge

(low side) has dropped to

approximately 29 inches of

vacuum, open the valve to the

vacuum thermocouple gauge.

See that the vacuum pump will

bank-off to a minimum of 50

microns. A high vacuum pump

can only produce a good vacuum

if its oil is not contaminated.

5. If the vacuum pump is working

properly, close the valve to the

vacuum thermocouple gauge

and open the high and low side

valves or the high vacuum

manifold set. With the valve on

the charging cylinder closed,

open the manifold valve to the

cylinder.

6. Evacuate the system to at least

29 inches gauge before opening

valve to thermocouple vacuum

gauge.

7. Continue to evacuate to a

minimum of 250 microns. Close

valve pump and watch rate of

rise. If vacuum does not rise

above 1500 microns in three

minutes, system can be

considered properly evacuated.

8. If thermocouple vacuum gauge

continues to rise and levels off at

about 5000 microns, moisture

and non-condensables are still

present. A leak is present if the

gauge continues to rise. Repair

and re-evacuate.

9. Close valve to the thermocouple

vacuum gauge and vacuum

pump. Shut off pump and

prepare to charge.

Charging the System

Charge the system with the exact

amount of refrigerant. Refer to the

unit nameplate for the correct

refrigerant charge. An inaccurately

charged system will cause future

problems.

Charging Procedure

1. When using an ambient-

compensated calibrated

charging cylinder, allow liquid

refrigerant only to enter the high

side.

2. After the system receives all the

refrigerant it requires, close

close the valve on the high side

of the manifold.

3. Start the system and charge the

balance of the refrigerant though

the low side. Do not charge in a

liquid form.

4. Close the low side valve on the

manifold and pinch-off both

process tubes. Remove the

manifold set. Crimp shut the

open ends of the process tubes

and braze.

5. Recheck for refrigerant leaks.

Refrigerant

Do not use a refrigerant other than

that shown on the unit nameplate.

Follow all precautionary measures

recommended by the refrigerant

manufacturers.

Line Piercing Valves

Line piercing valves may be used for

diagnosis but are not suitable for

evacuating or charging due to the

minute holes pierced in the tubing.

Line piercing valves must not be left

on the refrigerant system. The

connection between the valve and

the refrigerant tubing is not

hermetically sealed and will

eventually leak.

Open Lines

Never leave refrigerant lines open to

the atmosphere when processing the

refrigeration system. Water vapor

may enter the lines and cause

improper evacuation.

Operating Test

The final step in a successful repair is

an accurate operating test. Follow the

cooling and heating performance

tests on pages 36 - 37 to make sure

the product is performing to design

standards.

WARNING

Hazardous Voltage!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

WARNING

Live Electrical Components!

During installation, testing, servicing

and troubleshooting of this product,

it may be necessary to work with live

electrical components. Have a

qualified licensed electrician or other

individual who has been properly

trained in handling live electrical

components perform these tasks.

Failure to follow all electrical safety

precautions when exposed to live

electrical components could result in

death or serious injury.

Figure 24. Proper placement of

discharge and inlet air thermostats

Place discharge and

inlet air thermostats

Place inlet thermostat

in center of grille

PTAC-SVX01C-EN 35

Maintenance

Cooling Performance Test

Thermometers

The following precautions are

necessary in observing the

thermometer readings in the cooling

performance test.

1. Use two accurately calibrated

refrigeration type thermometers

or a thermocouple

potentiometer.

2. Thermometers are affected by

body heat or changes in airflow.

Therefore, secure the

thermometers in proper

locations with masking tape,

wire, or other applicable

retainers.

3. Observe readings without

touching or moving the

thermometers.

Sling Psychrometer

Use a sling psychrometer to obtain

the wet-bulb temperature and

determine the percent relative

humidity.

To obtain the wet-bulb, follow this

procedure using the sling

psychrometer.

• Saturate the wick (only once

during procedure of obtaining

wet-bulb readings) with clean

water slightly below room

temperature.

• Obtain the psychrometer reading

five to six feet in front of the unit

and approximately four feet off

the floor.

Note: Direct discharge airflow away

from the sling psychrometer.

Do not perform the cooling

performance test when the outside

temperature is 20°F below the room

temperature. For best results,

perform the test under peak load

conditions.

The air conditioner must operate at

least 20 minutes on the HIGH COOL

position before testing.

Cooling Performance Test

Record the following temperatures

for the cooling performance test:

• Dry-bulb temperature of return

air at conditioner. Locate

thermometer as illustrated on

previous page.

• Dry-bulb temperature of

discharge air. Locate the

thermometer as illustrated on

previous page.

• The dry-bulb thermometer

temperature on the sling

psychrometer should be plus or

minus 1°F within reading

obtained on thermometer in the

return air. Check wet-bulb

temperature on sling

psychrometer and record same.

• After recording the wet-bulb

temperature, dry- bulb

temperature, and return air

temperature, calculate the

temperature difference as

follows.

• Subtract temperature obtained in

Step B from temperature

obtained in Step A. Use the

remainder temperature to

calculate from the cooling

change of temperature in the

Maintenance general

information section.

Example: Assume a PTHE1501 unit is

under test and the temperature

readings indicated below were

obtained.

1. Return air dry-bulb temperature:

80°F, Step A.

2. Discharge air dry-bulb

temperature: 69°F, Step B.

3. Return air, wet and dry-bulb

temperature as recorded in Step

C: dry- bulb 80°F, wet-bulb 75°F.

4. In left hand column of cooling

capacity charge headed dry-bulb,

find the 80° value in Table 20,

p. 25.

5. In column headed wet-bulb find

the 75° value and find the value

"8 -13" in the cooling range

column under model

“PTHE1501”.

This data shows the temperature of

the air passing through the cooling

coil is reduced at least 8°F but not

more than 13°F. This example unit is

operating normally for the existing

conditions.

For the example unit under test, the

temperature difference was 11°F

(80°F, return air, minimum 69°F

discharge air). Because the value is

within the listed cooling range 8 - 13,

this unit is considered to be

operating normally.

Note: Never test operation without

the unit in the wall sleeve. A

serious change in design

specifications for air

movement through the

evaporator and condenser

compartments, causing the

fan motor to over heat and

the refrigeration system to

become unbalanced will

occur when the unit is not

installed in the wall sleeve.

Electric Heat Test

For the electric heat test, the

following readings must be recorded

after the unit is interconnected with a

wattmeter or by recording the total

amp draw to the unit.

Note: The cabinet front must be in

place during this test.

• Record supply voltage to unit.

• Operate unit in highest heat

setting.

• Record wattage recorded on

wattmeter or total amp draw to

unit.

• Refer to the electric heat capacity

and electrical data section

(whichever is applicable for

voltage rating on the unit being

tested.)

• The total watts or amps recorded

should fall with in the minimum

and maximum watts/amps listed

on these charts

Example: Assume that a PTHE1501

230/208V with 3.5 kW electric heater

is under test.

1. Supply voltage as recorded -

208V.

2. Watts recorded -2750W or amps

recorded - 13.5 amps.

36 PTAC-SVX01C-EN

Maintenance

3. Locate the readings listed in the

Operation section of this manual.

You will note that these readings

fall within the voltage, watts and

amp draw minimum and

maximum ranges listed.

Therefore, the unit heating

performance would be

considered normal.

Heating Power Consumption

Te s t

(Heat Pump Mode Only)

For the heating wattage, record the

following readings after the unit is

interconnected with a wattmeter.

• Outside coil inlet air dry-bulb

temperature.

• Inside coil inlet air dry-bulb

temperature.

• Total watts input measured by

wattmeter.

Calculating procedure

1. Locate temperature obtained in

Step A of cooling performance

test in first column of Heating

Wattage Chart.

2. Locate in second column the

inside coil inlet dry-bulb

temperature.

3. The total watts input should

come between minimum and

maximum values indicated for

each model.

Example: Assume that a PTHE1501 is

under test. Proceed as follows and

observe test readings as

simultaneously as possible.

1. Outside coil inlet dry-bulb

temperature readings as

described above: 45°F.

2. Check watts input: 1370 W

3. Inside coil inlet dry-bulb

temperature reading as de

scribed in Step B: 75°F.

Read to the right from the 75° inside

coil inlet dry-bulb value in the

column and note the minimum and

maximum wattage of 1335 - 1470.

Since the wattage reading (1370)

obtained in the test is within the

prescribed range, the total power

input in watts is considered to be

normal.

WARNING

Live Electrical Components!

During installation, testing, servicing

and troubleshooting of this product,

it may be necessary to work with live

electrical components. Have a

qualified licensed electrician or other

individual who has been properly

trained in handling live electrical

components perform these tasks.

Failure to follow all electrical safety

precautions when exposed to live

electrical components could result in

death or serious injury.

WARNING

Hazardous Voltage!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

WARNING

Hazardous Voltage

w/Capacitors!

Disconnect all electric power,

including remote disconnects and

discharge all motor start/run

capacitors before servicing. Follow

proper lockout/tagout procedures to

ensure the power cannot be

inadvertently energized. Verify with

an appropriate voltmeter that all

capacitors have discharged. Failure

to disconnect power and discharge

capacitors before servicing could

result in death or serious injury.

Resistance Check

Discharge capacitor and remove wire

leads. Use a DC volt meter to verify

there is no power.

Testing Capacitor Resistance

1. Set an ohmmeter on its highest

ohm scale and connect the leads

to the capacitor.

a. Good Condition - indicator

swings to zero and slowly

returns to infinity. (Start

capacitor with bleed resistor

will not return to infinity. It

will still read the resistance of

the resistor).

b. Shorted - indicator swings to

zero and stops there -

replace.

c. Open - no reading - replace.

(Start capacitor would read

resistor resistance).

2. Testing for ohms between either

capacitor terminal and the

capacitor body must show

infinite ohms.

Capacitance Check

Using a hookup as shown below,

take the amperage and voltage

readings and use them in the formula

below the diagram.

Overloads

1. With no power to the unit,

remove the overload lead from

the compressor terminal.

2. Using an ohmmeter: Test

continuity between terminals of

the overload. If not continuous,

the overload is open, replace the

overload.

Compressor Windings

WARNING

Electrical Shock!

Do not connect electrical power to

this unit or to the compressor if the

compressor terminal cover has been

removed or is not firmly in place.

Doing so could result in death,

serious injury, or property damage.

If the test indicates shorted,

grounded or open windings, see

procedure for the next steps to be

taken.

PTAC-SVX01C-EN 37

Maintenance

Resistance Test

1. With no power, remove the leads

from the compressor terminals.

2. Touch the leads of an ohmmeter

to terminals C-S, start windings

and C-R, run winding.

If either winding does not test

continuous, replace the compressor.

Testing capacitance

capacitance (MFD) =

2650 X amperage

voltage

Note: Replace the capacitor if the

value obtained is not within

10% of the rating printed on

the capacitor.

Ground Test

WARNING

Live Electrical Components!

During installation, testing, servicing

and troubleshooting of this product,

it may be necessary to work with live

electrical components. Have a

qualified licensed electrician or other

individual who has been properly

trained in handling live electrical

components perform these tasks.

Failure to follow all electrical safety

precautions when exposed to live

electrical components could result in

death or serious injury.

Figure 25. Testing capacitor

resistance

15 amp

fuse

Voltmeter

Ammeter

Capacitor

With no power and compressor leads

removed:

Set an ohmmeter on its highest scale.

Touch one lead to the compressor

body (clean point of contact, as a

good connection is a must) and the

other probe to each compressor

terminal in turn. If a reading is

obtained, then compressor is

grounded and must be replaced.

If the voltage, capacitor, overload and

motor windings test fail to show the

cause for failure:

1. With no power, wire a test cord

to line voltage (Line & N).

Note: The wire size of the test cord

must equal the line size, and

the fuses in the test line must

be of the proper size and

type.

2. Connect a good capacitor of the

right MFD and voltage rating into

the circuit as shown in Figure 40.

3. Carefully apply line voltage.

a. If the compressor starts and

continues run, the cause for

failure is somewhere else in

the system.

Figure 26. Compressor ground test

Figure 27. Test cord connections

Ohmeter Compressor

top

Outlet

Terminals Accumulator

b. If the motor fails to start -

replace. Since all single

phase compressors are of the

permanent split capacitor

design the high and low side

pressure must be

approximately equal or the

low torque compressor may

not start.

Indoor Coil and Air

Thermistors

1. Remove the Indoor Coil

Thermistor leads from the circuit

board.

2. Check the resistance of the

Indoor Coil Thermistor against

the table on the next page. The

leads of the ohm meter will need

to contact the ends of the

thermistors that connect to the

board.

3. Replace the Indoor Coil

Thermistor if it does not test as

above.

Outdoor Coil and Air

Thermistors

1. Remove the outdoor coil

thermistor leads from the circuit

board.

2. Check the resistance of the

outdoor coil thermistor against

the table on the next page. The

leads of the ohm meter will need

to contact the ends of the

thermistors that connect to the

board.

3. Replace the outdoor coil

thermistor if it does not test as

above.

Heater Assembly with Power

OFF to the Unit and Heater

1. Remove the heaters in question

and visually inspect the element

for broken condition. Refer to the

disassembly procedures for

information on disassembling

the heater.

2. Test the thermal fuse (one time

fuse). If open, replace the heater

assembly.

38 PTAC-SVX01C-EN

Maintenance

Table 27. Thermistor indoor coil

resistance

x (C°)

Rmin

(kΩ)

Rnom

(kΩ)

Rmax

(kΩ)

-40.0 327.6037 342.7771 358.6311

-39.0 306.4713 320.4512 335.0471

-38.0 286.8464 299.7818 313.1748

-37.0 268.6117 380.4928 292.8787

-36.0 251.6597 262.6189 274.0353

-35.0 235.8919 246.0045 258.5312

-34.0 221.2181 230.5528 240.2626

-33.0 207.5554 216.1750 225.1344

-32.0 194.8276 202.7896 211.0696

-31.0 182.9649 190.3219 197.9580

-30.0 171.9031 178.7032 186.7663

-29.0 161.5829 167.8703 174.3869

-28.0 161.9502 157.7652 163.7880

-27.0 142.9647 148.3344 163.9026

-26.0 134.5504 139.5289 144.6781

-25.0 126.6948 131.3031 126.0653

-24.0 119.3487 123.6155 128.0227

-23.0 112.4758 116.4275 120.5064

-22.0 106.0429 109.7036 113.4795

-21.0 100.0191 103.4109 106.9073

-20.0 94.3758 97.5193 100.7575

-19.0 89.0868 92.0070 95.0050

-18.0 84.1276 86.8293 89.6087

-17.0 79.4758 81.9811 84.5569

-16.0 75.1104 77.4341 79.8216

-15.0 71.0121 73.1677 75.3810

-14.0 67.1629 69.1629 71.2151

-13.0 63.5463 65.4021 67.3053

-12.0 60.1468 61.8691 63.6342

-11.0 56.9501 68.6487 60.1860

-10.0 53.9430 55.4269 56.9458

-9.0 51.1130 52.4905 53.8998

-8.0 48.4488 49.7278 51.0353

-7.0 45.9395 47.1271 48.3404

-6.0 43.5756 44.6782 45.8041

-5.0 41.3475 42.3713 43.4161

-4.0 39.2467 40.1974 41.1670

-3.0 37.2652 38.1480 39.0478

-2.0 35.3956 36.2153 37.0504

-1.0 33.6309 34.3920 35.1569

0.0 31.9646 32.6713 33.3904

1.0 30.3900 31.4600 31.7132

2.0 28.9023 29.5113 30.1303

3.0 27.4964 28.0617 28.6358

4.0 26.1673 26.6919 27.2244

5.0 24.9103 25.3971 25.8909

6.0 23.7211 24.1727 24.6306

7.0 22.5967 23.0148 23.4391

8.0 21.5303 21.9188 22.3122

9.0 20.5214 20.8816 21.2461

10.0 19.5667 19.8995 20.2371

11.0 18.6600 18.9693 19.2819

12.0 17.8015 18.0880 18.3773

13.0 18.9874 17.2527 17.5204

14.0 16.2153 16.4608 16.7083

15.0 16.4827 16.7098 16.9385

16.0 14.7874 14.9973 16.2087

17.0 14.1272 14.3212 14.5164

18.0 13.5003 13.6794 13.8595

19.0 12.9048 13.0700 13.2381

20.0 12.3389 12.4912 12.6442

21.0 11.8010 11.9413 12.0821

22.0 11.2895 11.4187 11.5482

23.0 10.8031 10.9219 11.0408

24.0 10.3404 10.4494 10.5585

25.0 9.9000 10.0000 10.1000

26.0 9.4726 9.5724 9.6724

27.0 9.0659 9.1656 9.2652

28.0 8.6790 8.7781 8.8774

29.0 8.3106 8.4091 8.6078

30.0 7.9600 8.0577 8.6078

31.0 7.6280 7.7229 7.8203

32.0 7.3078 7.4089 7.5004

33.0 7.0047 7.0997 7.1952

34.0 6.7157 6.8087 6.9042

35.0 6.4402 6.5330 6.6264

36.0 6.1775 6.2691 6.3614

37.0 5.9269 6.0173 6.1083

38.0 5.6878 6.7769 5.8667

39.0 5.4598 5.5474 5.6359

40.0 5.2418 5.3282 5.4154

41.0 5.0388 5.1188 5.2047

42.0 4.8351 4.9188 5.0033

43.0 4.6454 4.7275 4.8107

44.0 4.4640 4.5449 4.6268

45.0 4.2907 4.3701 4.4504

46.0 4.1300 4.2050 4.2850

47.0 3.9665 4.0432 4.1207

48.0 3.8161 3.8902 3.9663

49.0 3.6701 3.7438 3.8185

Table 27. Thermistor indoor coil

resistance (continued)

x (C°)

Rmin

(kΩ)

Rnom

(kΩ)

Rmax

(kΩ)

50.0 3.5314 3.6037 3.6770

51.0 3.3982 3.4691 3.6410

52.0 3.2707 3.3402 3.4107

53.0 3.1487 3.2169 3.2860

54.0 3.0320 3.0967 3.1665

55.0 2.9201 2.9856 3.0519

56.0 2.8130 2.8771 2.9422

57.0 2.7104 2.7732 2.8370

58.0 2.6121 2.6736 2.7380

59.0 2.5179 2.5781 2.6393

60.0 2.4276 2.4855 2.5464

61.0 2.3410 2.3986 2.4573

62.0 3.2579 2.3144 2.3719

63.0 2.1782 2.2335 2.2898

64.0 2.1018 2.1559 2.2110

65.0 2.0284 2.0813 2.1353

66.0 1.9580 2.0098 2.0628

67.0 1.8904 1.9411 1.9928

68.0 1.8255 1.8750 1.9257

69.0 1.7631 1.8116 1.8612

70.0 1.7631 1.8116 1.8512

71.0 1.6456 1.6921 1.7395

72.0 1.5903 1.6357 1.6822

73.0 1.5371 1.5816 1.6270

74.0 1.4860 1.5816 1.6270

75.0 1.4368 1.4793 1.5229

76.0 1.3895 1.4311 1.4737

77.0 1.3440 1.3847 1.4284

78.0 1.3003 1.3400 1.3809

79.0 1.2581 1.2970 1.3370

80.0 1.2176 1.2558 1.2947

81.0 1.1785 1.2158 1.2540

82.0 1.1409 1.1773 1.2148

83.0 1.1047 1.1403 1.1770

84.0 1.0698 1.1047 1.1405

85.0 1.0362 1.0703 1.1054

86.0 1.0038 1.0372 1.0715

87.0 0.9726 1.0052 1.0388

88.0 0.9425 0.9744 1.0073

89.0 0.9135 0.9447 0.9769

90.0 0.8858 0.9161 0.9476

Table 27. Thermistor indoor coil

resistance (continued)

x (C°)

Rmin

(kΩ)

Rnom

(kΩ)

Rmax

(kΩ)

PTAC-SVX01C-EN 39

Maintenance

WARNING

Hazardous Voltage!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

Reversing Valve

Occasionally the reversing valve may

stick in the heating or cooling

position or in the mid-operation.

When stuck in the mid-position, part

of the discharge gas from the

compressor is directed back to the

suction side resulting in excessively

high suction pressure.

Check the operation of the valve by

starting the system and switching the

operation from COOLING to

HEATING and then back to COOLING.

If no voltage is registered to the coil,

check the operation of the reversing

relay and the continuity of the

connecting wires.

If voltage is registered at the coil, tap

the valve body lightly while switching

the system from HEATING to

COOLING etc. If this fails to cause the

valve to switch position, remove the

coil connector cap and wiring and

test the continuity of the valve coil. If

the coil does not test continuous

replace it.

If the valve is inoperative, replace.

Component Replacement

Replacement of the compressor,

evaporator, condenser, capillary

tubes and reversing valve must be in

accordance with accepted service

practices. These procedures include

a complete evacuation of both high

and low sides, and changing of the

capillary tube assembly whenever

the refrigerant system is opened.

Before replacing a component in the

sealed system, make sure that the

cause for complaint does not lie in

the electrical circuit, control, overload

or is due to some other reason. The

serviceman must be familiar with the

operational characteristics of the

product and should not jump to

conclusions.

Temperature-Actuated Drain

Valve (model PTHE Only)

The PTHE is equipped with a

temperature-actuated drain valve

located in the base pan. As the

outdoor ambient decreases to 55°F,

the drain valve will begin to open.

The valve will be completely open

when the outdoor ambient

temperature falls to 50°F.

WARNING

Hazardous Voltage!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

Unit Disassembly Procedures

1. Disconnect power to the unit.

2. Remove the unit front cover.

3. Remove the three screws on

each side of the chassis that

secure the chassis to the wall

sleeve.

4. Carefully slide the chassis out of

the wall sleeve and place on floor

or a protected cart.

WARNING

Hazardous Voltage!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

Note: ALL phases of this

installation must comply with

NATIONAL, STATE AND

LOCAL CODES. Improper

wiring or installation may

damage thermostat.

Power Cord Removal

1. Disconnect power to the unit.

2. Remove the unit front cover.

3. Remove two screws of power

cord connector front cover.

4. Remove the power cord strain

relief.

5. Remove power cord from

connector.

Power cord Installation

1. Install power cord to connector.

Gently press the connector into

position until top and bottom

latches engage.

2. Reinstall the power cord strain

relief.

3. Reinstall power cord connector

front cover.

4. Reinstall the unit front cover.

Capacitor Removal

1. Remove the control box. Refer to

the power cord disassembly for

instructions on removing the

control box.

2. Remove the screw securing the

capacitor to the control box.

Heater Assembly Removal

1. Remove the strain relief.

2. Remove the three screws

securing the discharge screen to

the chassis.

3. Unplug the power cord

connector and remove the power

cord.

Removing the Indoor Coil and

Indoor Air Thermistors

1. Remove the front cabinet.

2. Remove the control box cover.

3. Disconnect the indoor coil/air

thermistor wiring from the

control board.

4. Locate the indoor coil/air

thermistor on the suction tube or

evaporator. Gently pull the

thermistor from the housing.

5. Remove the indoor coil/air

thermistor from the unit.

40 PTAC-SVX01C-EN

Maintenance

Removing the Outdoor Coil

and Outdoor Air Thermistors

1. Remove the chassis from the

wall.

2. Remove the front cabinet.

3. Remove the control box cover.

4. Disconnect the outdoor coil/air

thermistor wiring from the

control board.

5. Gently pull outdoor coil

thermistor from the bracket near

the capillary tube.

6. Gently remove outdoor air

thermistor which is located at the

drain valve.

7. Remove the outdoor coil/air

thermistor from the unit.

Indoor Fan and Motor

1. Remove the chassis from the

wall.

2. Remove the front cabinet.

3. Remove the heater/discharge

deck assembly. (Refer to the

heater disassembly instructions)

4. Remove the control box cover.

Disconnect the control wiring.

Remove the control box. Refer to

the power cord disassembling

for instructions on

disassembling the control box.

5. Remove the indoor fan motor

bracket screws (3) as shown.

6. Remove the set screw (you will

need a long Allen wrench)

securing the indoor fan to the

motor shaft and remove the

indoor fan and motor.

Outdoor Fan and Motor

1. Follow the directions for

removing the condenser except

don’t braze or remove the tubing

connecting to the condenser.

Capturing the system refrigerant

is also not necessary.

2. Remove the screw on the right

side of the unit (If you are

looking at the back of the PTAC)

toward the bottom of the PTAC

near the lip of the basepan.

3. Lift the condenser up and over

the lip of the basepan and move

just enough to gain access to the

outdoor fan and motor. Be

careful not to damage the

bottom of the condenser by

sitting it on the lip of the

basepan. Also, use caution when

bending the condenser to gain

access to the outdoor fan and

motor. The tubing is very fragile

and must be treated with care.

4. Remove the fan.

5. Remove the fan motor by

removing the two screws

securing it to the fan motor

bracket.

6. Disconnect the fan motor wiring

from the control by removing the

wire junction box cover on the

partition panel above the control

panel cover.

Control Board Replacement

Procedure

WARNING

Hazardous Voltage!

Disconnect all electric power,

including remote disconnects before

servicing. Follow proper lockout/

tagout procedures to ensure the

power can not be inadvertently

energized. Failure to disconnect

power before servicing could result

in death or serious injury.

Note: Before replacing the whole

control board, make sure that

the control board’s fuse is still

functioning. The specs for

the control board fuse are:

5X20mm, 250V, 315mA, fast

acting. For more information

on a blown fuse on the

Control Board, check the

Troubleshooting section of

this document.

1. Remove plastic cabinet front and

the metal cover that encloses the

control board

2. Remove the replacement board

from its package and set the

power jumper to match the unit

voltage .

3. There are two different pin

connections, one for 230/208

VAC and another for 265 VAC .

The jumper for the 115 VAC

board is pre-installed in the P8

to P9 position.

Note: This is a very important

step, and it might lead to

damage of the control

board if the jumper is not

properly set.

4. Remove connections from the

existing control board, tagging

wires as required to ensure

correct re-assembly.

5. Remove 2 screws from the front

plastic mounting ears. Remove

the screw from the green wire

ground. Slide plastic chassis and

board back and lift out of place.

6. Engage catches on bottom of

plastic chassis of replacement

assembly with sheet metal

control box and slide forward to

lock in position. Re-install two

screws through the front plastic

mounting ears. Re-install green

ground wire.

7. Re-connect the wiring harness to

the new assembly in the same

positions that they were before

removal. This includes

temperature thermistors, as well

as the thermostats, zone sensors

and energy management.

8. Reinstall the sheet metal cover

over the control board.

9. Position the front cabinet over

the chassis and push the sides

until the retaining clips engage.

Figure 28. Power jumper

PTAC-SVX01C-EN 41

Diagnostics

The controller is equipped to display

a diagnostic code through the

interface module; if the display is not

present (Class 2 control), there is no

method to retrieve the diagnostic

codes from the unit.

If there is no interface module to

indicate the presence of a diagnostic,

service will only be triggered by a

comfort or operational complaint.

The controller will only display the

most severe diagnostic present.

Translating Multiple

Diagnostics

The controller senses and records

each diagnostic independently of

other diagnostics. It is possible to

have multiple diagnostics affect the

operation of the unit, but only the

most severe diagnostic will be

displayed.

Resetting Diagnostics

A reset clears any latching

diagnostics and allows the control to

try to run the PTAC normally. If the

latching condition is still present

after the reset, the control will shut

down the PTAC. A reset will reset a

unit that is running normally. A reset

is just like cycling power to the unit.

There are two ways to reset

diagnostics:

1. Manual output test at the

controller

2. Cycling power to the controller

Manual Output Test

When manual test has been initiated,

the controller exercises all outputs in

a predefined sequence. The last step

of the sequence resets the controller.

See the Manual output test section

on page 22 for more information

about the manual output test.

Cycling Power

When someone turns off the

controller’s power, then re-applies

power, the unit cycles through a

power up sequence. By default, the

controller will attempt to reset all

diagnostics at power up.

Diagnostics present at power up and

those that occur after power up will

be handled according to the defined

unit diagnostics sequences (see

Diagnostics table below)

Table 28. Diagnostic codes

Severity

Level

Diagnostic

Code

Diagnostic

Description Compressor

Auxiliary

Heat Indoor Fan

1

(severest)

C1 Compressor Failure DISABLED ENABLED ENABLED

2 C2 Indoor Temperature

Unit Sensor Failure1

ENABLED ENABLED ENABLED

3 C3 Indoor Temperature

Display Sensor Failure

ENABLED ENABLED ENABLED

4 C4 Indoor Coil

Temperature Failure

ENABLED2 ENABLED ENABLED

5 C5 Outdoor Temperature

Failure

ENABLED,

run as PTEE

ENABLED,

run as PTEE

ENABLED,

run as PTEE

6 C6 Outdoor Coil

Temperature Failure

ENABLED,

run as PTEE

ENABLED,

run as PTEE

ENABLED,

run as PTEE

7C7Configuration

Corrupted

ENABLED ENABLED ENABLED

8 - No diagnostic present ENABLED ENABLED ENABLED

Table 29. Latching diagnostics, reset

required

Code Diagnostic Description Description

C1 Compressor Failure OLP has had multiple trips (3)

C7 Configuration Corrupted configuration failure

Table 30. Automatically resetting

diagnostics

Code Diagnostic Description Description

C1 Indoor Temperature - No Backup

Available

No source of indoor temperature is

available

C2 Indoor Temperature - Unit Sensor

Failure1

Unit indoor temperature valid then not

valid

C3 Indoor Temperature - Display Sensor

Failure1

Display indoor temperature valid then not

valid

C4 Indoor Coil Temperature Failure Indoor Coil Temperature valid then not

valid

C5 Outdoor Temperature Failure Outdoor Temperature valid then not valid

C5 Outdoor Coil Temperature Failure Outdoor Coil temp valid then not valid

Troubleshooting

42 PTAC-SVX01C-EN

Troubleshooting

Table 31. Compressor output does not energize

Probable cause Explanation

Random restart timer All controller outputs remain off until the timer expires.

Selected mode OFF When off is selected at the display to the controller, the unit controls all outputs off.

Selected mode FAN ONLY When fan only is selected at the display to the controller, the unit only allows the indoor fan to energiz.

Diagnostic present A specific list of diagnostics affects compressor operation. For more information, see the Diagnostics section in the

manual.

No power to the

controller

If the controller does not have power, the compressor does not operate. For the controller to operate normally, it

must have an input voltage of 115 or 230/208, 265 VAC.

Manual output test The controller includes a manual output test sequence you can use to verify output operation and associated

output wiring. However, based on the current step in the test sequence, the compressor may not be on. Refer to

the Manual Output Test section.

Unit wiring The wiring between the controller output and the compressor must be present and correct for normal operation.

Indoor Coil Freeze

protection

The compressor has been turned off because the indoor coil temperature has fallen below 35°F and has not risen

above 50°F

Table 32. Indoor/remote fan outputs do not energize

Probable cause Explanation

Random restart timer All controller outputs remain off until the timer expires.

Normal operation Depending on the configuration selected the fan(s) may be only cycle with the compressor output

Selected mode OFF When off is selected at the display to the controller, the unit controls all outputs off.

Diagnostic present A specific list of diagnostics affects fan operation. For more information, see the Diagnostics section in the manual.

No power to the

controller

If the controller does not have power, the compressor does not operate. For the controller to operate normally, it

must have an input voltage of 230/208, 265 VAC.

Manual output test The controller includes a manual output test sequence you can use to verify output operation and associated output

wiring. However, based on the current step in the test sequence, the fan(s) may not be on. Refer to the Manual

Output Test section.

Unit wiring The wiring between the controller outputs and the fan relays and contacts must be present and correct for normal

fan operation.

Table 33. Outdoor fan output does not energize

Probable cause Explanation

Random restart timer All controller outputs remain off until the timer expires.

Selected mode OFF When off is selected at the display to the controller, the unit controls all outputs off.

Selected mode FAN ONLY When fan only is selected at the display to the controller, the unit only allows the indoor fan to energize.

Diagnostic present A specific list of diagnostics affects compressor and therefore the outdoor fan operation. For more information, see

the Diagnostics section in the manual.

No power to controller If the controller does not have power, the compressor does not operate. For the controller to operate normally, it

must have an input voltage of 115 or 230/208, 265 VAC.

Manual output test The controller includes a manual output test sequence you can use to verify output operation and associated output

wiring. However, based on the current step in the test sequence, the outdoor fan may not be on. Refer to the

Manual Output Test section.

Unit wiring The wiring between the controller output and the outdoor fan must be present and correct for normal operation.

Coil Burst Protection The outdoor fan has been turned off because the indoor coil temperature has risen above 140°F and has not fallen

below 125°F

Normal operation The outdoor fan cycles with the compressor output

Defrost Cycle During the active defrost cycle the outdoor fan is controlled off. See the section on defrost control.

Unit wiring The wiring between the controller outputs and the fan relays and contacts must be present and correct for normal

fan operation.

PTAC-SVX01C-EN 43

Troubleshooting

Table 34. Reversing valve output does not energize

Random restart timer Explanation

Power up control wait All controller outputs remain off until the timer expires.

Se le c te d m o d e O F F, FA N

ONLY

Reversing valve held in current state because compressor use is not allowed.

Diagnostic present A specific list of diagnostics affects compressor operation. For more information, see the Diagnostics section in the

manual.

No power to the

controller

If the controller does not have power, the reversing valve does not operate. For the controller to operate normally, it

must have an input voltage of 115 or 208-230, 265 VAC.

Manual output test The controller includes a manual output test sequence you can use to verify output operation and associated output

wiring. However, based on the current step in the test sequence, the reversing valve may not be energized. Refer to

the Manual Output Test section.

Unit wiring The wiring between the controller output and the reversing valve must be present and correct for normal operation.

Normal operation PTHE unit is in heating mode.

Diagnostic present A specific list of diagnostics affects unit operation. For more information, see the Diagnostics section in the manual.

Table 35. Auxiliary heat output does not energize

Probable cause Explanation

Random restart timer All controller outputs remain off until the timer expires.

Selected mode OFF When off is selected at the display to the controller, the unit controls all outputs off.

Selected mode FAN

ONLY

When fan only is selected at the display to the controller, the unit only allows the indoor fan to energize.

Diagnostic present A specific list of diagnostics affects unit operation. For more information, see the Diagnostics section in the manual.

No power to the

controller

If the controller does not have power, the compressor does not operate. For the controller to operate normally, it

must have an input voltage of 115 or 230/208, 265 VAC.

Manual output test The controller includes a manual output test sequence you can use to verify output operation and associated output

wiring. However, based on the current step in the test sequence, the auxiliary heat may not be on. Refer to the

Manual Output Test section.

Unit wiring The wiring between the controller output and the auxiliary heat must be present and correct for normal operation.

Indoor Coil Freeze

protection

The compressor has been turned off because the indoor coil temperature has fallen below 35°F and has not risen

above 50°F.

Normal operation Auxiliary heat may not be needed to meet the load conditions see the section dealing with Auxiliary Heat Control.

Defrost Cycle During the active defrost cycle the auxiliary heat is controlled off. See the section on defrost control. Reversing

Valve output does not energize.

Table 36. Ventilation output does not energize

Probable cause Explanation

Random restart timer All controller outputs remain off until the timer expires.

Selected mode OFF When off is selected at the display to the controller, the unit controls all outputs off.

Diagnostic present A specific list of diagnostics affects unit operation. For more information, see the Diagnostics section in the manual.

No power to controller If the controller does not have power, the compressor does not operate. For the controller to operate normally, it

must have an input voltage of 115 or 230/208, 265 VAC.

Manual output test The controller includes a manual output test sequence you can use to verify output operation and associated output

wiring. However, based on the current step in the test sequence, the ventilation output may not be on. Refer to the

Manual Output Test section.

Unit wiring The wiring between the controller output and the ventilation must be present and correct for normal operation.

Normal operation See the section on Ventilation operation.

Defrost Cycle During the active defrost cycle the outdoor fan is controlled off. See the section on defrost control.

44 PTAC-SVX01C-EN

Troubleshooting

Table 37. Condensate pump does not energize

Probable cause Explanation

Random restart timer All controller outputs remain off until the timer expires.

Selected mode OFF When off is selected at the display to the controller, the unit controls all outputs off.

No power to controller If the controller does not have power, the compressor does not operate. For the controller to operate normally, it

must have an input voltage of 115 or 230/208, 265 VAC.

Manual output test The controller includes a manual output test sequence you can use to verify output operation and associated output

wiring. However, based on the current step in the test sequence, the condensate Pump may not be enabled. Refer to

the Manual Output Test section.

Unit wiring The wiring between the controller output and the Condensate Pump must be present and correct for normal

operation.

Normal operation Condensate Pump is available only with Heat Pumps. Unit is in active defrost, or outdoor temperature is below enable

point.

Unit wiring The wiring between the controller outputs and the fan relays and contacts must be present and correct for normal

condensate pump operation.

Defrost Cycle During the active defrost cycle the condensate pump power is removed. See the section on defrost control.

Table 38. Output on when the mode is off

Probable cause Explanation

Fan Configuration Fan is configured to run on high in off mode (see configuration section).

Freeze Protection While in off mode, freeze protection may be active. This will cause the indoor fan to run at high speed, and the

remote fan and auxiliary heat will be on.

Fan Delay Off The indoor fan continues to run after the compressor or auxiliary heat will be on.

Table 39. Control fuse is blown

Symptom

The generic thermostat does not work

The energy input does not work

The ventilation input does not work

The remote fan output does not work

PTAC-SVX01C-EN 45

Figure 29. 230/208V wiring diagram (07 models)

GR

YL

OR

BK

HI

L

N

L

H

N

BR

YL

LO

HI

N

RD

RD

YL

RD

BK

12345678

3.0KW

12345678

8765432 1

2.0KW

654321

RD

BK

WH

YL/GR

1.0KW

2.0KW

2.0KW

RD

RD

BK

REMOTE

FAN

RELAY

THERMOSTAT

REMOTE

VENTILATION

INPUT

DISPLAY

REMOTE

INPUT

ENERGY

L

BK

N

RD

LOCAL

DISPLAY

INDOOR TEMPERATURE

INDOOR COIL TEMPERATURE

OUTDOOR COIL TEMPERATURE

OUTDOOR TEMPERATURE

TL

TL FL

NC

NO

COM

BK

COM

NO

208/230

265

K8 HEAT

K9 COOL

P8

P9

P10

RF

CRW

GL

O

VT

EN

Y

GH

TB2 TB1

P4

P3 P2 P1

AIR

COIL

F1 T1

Cond

Vent

Fan Rev Valve

P15 P14 P13 P12 P11

CP - CONDENSATE PUMP

RD - RED

PVD - POWER VENTILATION DOOR

GR - GREEN

RVS - REVERSING VALVE

WH - WHITE

IM - INDOOR MOTOR

BK - BLACK

OM - OUTDOOR MOTOR

OR - ORANGE

COMP - COMPRESSOR YL - YELLOW

FACTORY WIRING

BL - BLUE

FIELD WIRING

BR - BROWN

1) For 208/230 VAC unit, connect P8 and P10.

2) For cooling only unit, there is no outdoor temperature sensor and reversing valve.

3) For different electric heater capacity, refer to IOM for power cord selection.

4) The specs for the control board fuse are: 5 x 20mm, 250V, 315mA, fast acting.

GND WIRE

RD

P7

OR

Wiring Diagram

46 PTAC-SVX01C-EN

Wiring Diagram

Figure 30. 230/208V Wiring diagram (09, 12, 15 models)

GR

YL

OR

BK

HI

L

N

L

H

N

BR

YL

LO

HI

N

RD

RD YL

RD

BK

87654321 5.0KW

12345678

3.0KW

12345678

8765432 1

2.0KW

654321

BL

RD

BK

WH

YL/GR

1.0KW

2.0KW

2.0KW

RD

RD

BK

REMOTE

FAN

RELAY

THERMOSTAT

REMOTE

VENTILATION

INPUT DISPLAY

REMOTE

INPUT

ENERGY

L

BK

N

RD

LOCAL

DISPLAY

INDOOR TEMPERATURE

INDOOR COIL TEMPERATURE

OUTDOOR COIL TEMPERATURE

OUTDOOR TEMPERATURE TL

TL FL

NC

NO

COM

BK

COM

NO

208/230 265

K8 HEAT K9 COOL

P8

P9

P10

RF CRWGL OVT EN

YGH

TB2 TB1

P4

P3 P2 P1

AIR COIL F1 T1

Cond Vent Fan Rev Valve

P15 P14 P13 P12 P11

CP - CONDENSATE PUMP RD - RED

PVD - POWER VENTILATION DOOR GR - GREEN

RVS - REVERSING VALVE WH - WHITE

IM - INDOOR MOTOR BK - BLACK

OM - OUTDOOR MOTOR OR - ORANGE

COMP - COMPRESSOR YL - YELLOW

FACTORY WIRING BL - BLUE

FIELD WIRING BR - BROWN

GND WIRE

RD

P7

OR

1

RVS

IM OM COMP

CP PVD

1

23

4

211

2

1) For 208/230 VAC unit, connect P8 and P10.

2) For cooling only unit, there is no outdoor temperature sensor and reversing valve.

3) For different electric heater capacity, refer to IOM for power cord selection.

4) The specs for the control board fuse are: 5 x 20mm, 250V, 315mA, fast acting.

PTAC-SVX01C-EN 47

Wiring Diagram

Figure 31. 265V Wiring diagram (07 models)

GR

OR

YL

OR

BK

HI

L

N

L

H

N

BR

YL

LO

HI

N

RD

RD

YL

RD

BK

12345678

3.0KW

12345678

8765432 1

2.0KW

65432 1

RD

BK

WH

YL/GR

1.0KW

2.0KW

2.0KW

RD

RD

BK

REMOTE

FAN

RELAY

THERMOSTAT

REMOTE

VENTILATION

INPUT

DISPLAY

REMOTE

INPUT

ENERGY

L

BK

N

RD

LOCAL

DISPLAY

INDOOR TEMPERATURE

INDOOR COIL TEMPERATURE

OUTDOOR COIL TEMPERATURE

OUTDOOR TEMPERATURE

TL

TL FL

NC

NO

COM

BK

COM

NO

K8 HEAT

K9 COOL

RF

CRW

GL

O

VT

EN

Y

GH

TB2 TB1

P4

P3 P2 P1

AIR

COIL

F1 T1

Cond

Vent

Fan

Rev Valve

P15 P14 P13 P12 P11

CP - CONDENSATE PUMP

RD - RED

PVD - POWER VENTILATION DOOR

GR - GREEN

RVS - REVERSING VALVE

WH - WHITE

IM - INDOOR MOTOR

BK - BLACK

OM - OUTDOOR MOTOR

OR - ORANGE

COMP - COMPRESSOR

YL - YELLOW

FACTORY WIRING

BL - BLUE

FIELD WIRING

BR - BROWN

1) For 265 VAC unit, connect P8 and P9.

2) For cooling only unit, there is no outdoor temperature sensor and reversing valve.

3) For different electric heater capacity, refer to IOM for power cord selection.

4) The specs for the control board fuse are: 5 x 20mm, 250V, 315mA, fast acting.

GND WIRE

RD

FUSE

208/230

265

P8

P9

P10 P7

48 PTAC-SVX01C-EN

Wiring Diagram

Figure 32. 265V Wiring diagram (09, 12, 15)

GR

OR

YL

OR

BK

HI

L

N

L

H

N

BR

YL

LO

HI

N

RD

RD YL

RD

BK

87654321 5.0KW

12345678

3.0KW

12345678

8765432 1

2.0KW

654321

BL

RD

BK

WH

YL/GR

1.0KW

2.0KW

2.0KW

RD

RD

BK

REMOTE

FAN

RELAY

THERMOSTAT

REMOTE

VENTILATION

INPUT DISPLAY

REMOTE

INPUT

ENERGY

L

BK

N

RD

LOCAL

DISPLAY

INDOOR TEMPERATURE

INDOOR COIL TEMPERATURE

OUTDOOR COIL TEMPERATURE

OUTDOOR TEMPERATURE TL

TL FL

NC

NO

COM

BK

COM

NO

K8 HEAT K9 COOL

RF CRWGL OVT EN

YGH

TB2 TB1

P4

P3 P2 P1

AIR COIL F1 T1

Cond Vent Fan Rev Valve

P15 P14 P13 P12 P11

CP - CONDENSATE PUMP RD - RED

PVD - POWER VENTILATION DOOR GR - GREEN

RVS - REVERSING VALVE WH - WHITE

IM - INDOOR MOTOR BK - BLACK

OM - OUTDOOR MOTOR OR - ORANGE

COMP - COMPRESSOR YL - YELLOW

FACTORY WIRING BL - BLUE

FIELD WIRING BR - BROWN

GND WIRE

RD

FUSE

208/230 265

P8

P9

P10 P7

RVS

IM OM COMP

CP PVD

1

23

4

211

2

1) For 265 VAC unit, connect P8 and P9.

2) For cooling only unit, there is no outdoor temperature sensor and reversing valve.

3) For different electric heater capacity, refer to IOM for power cord selection.

4) The specs for the control board fuse are: 5 x 20mm, 250V, 315mA, fast acting.

1

PTAC-SVX01C-EN 49

Wiring Diagram

Figure 33. Energy management system

Figure 34. 3rd party class 2 thermostat

wiring

Figure 35. Remote

display wiring

RWYGHGL

OVT EN

RWYGHGL

OVT EN

+_

+_

50 PTAC-SVX01C-EN

Full 1st Year Warranty

Trane will repair or replace any part

which proves to be defective due to

workmanship or materials, free of

charge. This includes parts and labor.

Full 2nd - 5th Sealed

System Warranty

Trane will repair or replace the

evaporator, condenser, compressor,

or connecting tubing which proves to

be defective due to workmanship or

materials, free of charge. This

includes parts and labor.

Limited 2nd through 5th

Year Functional Parts

Warranty

During the 2nd through 5th year,

Trane will provide functional parts

which prove to be defective due to

workmanship or materials.

Components covered are switches,

solenoids, fan motors, thermistors,

circuit boards, factory installed

heaters, blower wheel, fan propeller,

capacitors, compressor overloads

and drain valves.

This limited warranty does not

include diagnostic time, labor or any

transportation and/or reinstallation

charges that may be required.

Warranty

Literature Order Number PTAC-SVX01C-EN

Date 09/06

Supersedes PTAC-SVX01B-EN

Stocking Location Webb/Mason

The manufacturer has a policy of continuous product and product data improvement and reserves

the right to change design and specifications without notice.