Trane Rauj Cauj 20 To 120 Tons Installation And Maintenance Manual SS APG007 EN (10/11)

2015-04-02

: Trane Trane-Rauj-Cauj-20-To-120-Tons-Installation-And-Maintenance-Manual-684215 trane-rauj-cauj-20-to-120-tons-installation-and-maintenance-manual-684215 trane pdf

Open the PDF directly: View PDF .
Page Count: 28

Download
Open PDF In Browser	View PDF

Application Guide

Tube Size and Component Selection
RAUJ Split Systems (20-120 Tons)
R-410A Refrigerant
Fin and Tube Condensers

SAFETY WARNING
Only qualified personnel should install and service the equipment. The installation, starting up, and
servicing of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific
knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could
result in death or serious injury. When working on the equipment, observe all precautions in the literature
and on the tags, stickers, and labels that are attached to the equipment.

March 2012

SS-APG007-EN

Warnings, Cautions and Notices
Warnings, Cautions and Notices. Note that warnings, cautions and notices appear at
appropriate intervals throughout this manual. Warnings are provided to alert installing contractors
to potential hazards that could result in death or personal injury. Cautions are designed to alert
personnel to hazardous situations that could result in personal injury, while notices indicate a
situation that could result in equipment or property-damage-only accidents.
Your personal safety and the proper operation of this machine depend upon the strict observance
of these precautions.
Read this manual thoroughly before operating or servicing this unit.

ATTENTION: Warnings, Cautions and Notices appear at appropriate sections throughout this
literature. Read these carefully:

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.

CAUTIONs

Indicates a potentially hazardous situation which, if not avoided, could result in
minor or moderate injury. It could also be used to alert against unsafe practices.
Indicates a situation that could result in equipment or property-damage only
accidents.

NOTICE:

Important
Environmental Concerns!
Scientific research has shown that certain man-made chemicals can affect the earth’s naturally
occurring stratospheric ozone layer when released to the atmosphere. In particular, several of the
identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine, Fluorine
and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon (HCFCs). Not all
refrigerants containing these compounds have the same potential impact to the environment.
Trane advocates the responsible handling of all refrigerants—including industry replacements for
CFCs such as HCFCs and HFCs.

Responsible Refrigerant Practices!
Trane believes that responsible refrigerant practices are important to the environment, our
customers, and the air conditioning industry. All technicians who handle refrigerants must be
certified. The Federal Clean Air Act (Section 608) sets forth the requirements for handling,
reclaiming, recovering and recycling of certain refrigerants and the equipment that is used in these
service procedures. In addition, some states or municipalities may have additional requirements
that must also be adhered to for responsible management of refrigerants. Know the applicable
laws and follow them.

WARNING
Proper Field Wiring and Grounding Required!
All field wiring MUST be performed by qualified personnel. Improperly installed and grounded
field wiring poses FIRE and ELECTROCUTION hazards. To avoid these hazards, you MUST
follow requirements for field wiring installation and grounding as described in NEC and your
local/state electrical codes. Failure to follow code could result in death or serious injury.

SS-APG007-EN

Warnings, Cautions and Notices

WARNING
Personal Protective Equipment (PPE) Required!
Installing/servicing this unit could result in exposure to electrical, mechanical and chemical
hazards.
•

Before installing/servicing this unit, technicians MUST put on all Personal Protective
Equipment (PPE) recommended for the work being undertaken. ALWAYS refer to appropriate
MSDS sheets and OSHA guidelines for proper PPE.

•

When working with or around hazardous chemicals, ALWAYS refer to the appropriate MSDS
sheets and OSHA guidelines for information on allowable personal exposure levels, proper
respiratory protection and handling recommendations.

•

If there is a risk of arc or flash, technicians MUST put on all Personal Protective Equipment
(PPE) in accordance with NFPA 70E or other country-specific requirements for arc flash
protection, PRIOR to servicing the unit.

Failure to follow recommendations could result in death or serious injury.

WARNING
R-410A Refrigerant under Higher Pressure than R-22!
The units described in this manual use R-410A refrigerant which operates at higher pressures
than R-22 refrigerant. Use ONLY R-410A rated service equipment or components with these
units. For specific handling concerns with R-410A, please contact your local Trane
representative.
Failure to use R-410A rated service equipment or components could result in equipment
exploding under R-410A high pressures which could result in death, serious injury, or
equipment damage.

Trademarks
Trane, Frostat and the Trane logo are trademarks of Trane in the United States and other countries.
All trademarks referenced in this document are the trademarks of their respective owners.

SS-APG007-EN

Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Updated Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Liquid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Suction Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Equipment Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Line Sizing, Routing, and Component Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Liquid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Line Sizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4
4
5
5

Suction Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Line Sizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6
6
6
7

Expansion Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hot Gas Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remodel, Retrofit, or Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Examples of Field-Installed Evaporator Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Single-Circuit RAUJs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dual-Circuit RAUJs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

SS-APG007-EN

iii

SS-APG007-EN

Overview
Trane’s RAUJ 20- through 120-ton condensing unit product line incorporating fin and tube
condenser coils has been designed for use only with R-410A and POE oil. R-410A is a high-pressure
refrigerant that requires the other components of the system, including the evaporator, to be rated
for R-410A pressures. For compressor lubrication, the refrigerant requires POE oil.
Traditionally, refrigerant piping practices were guided by four principles:
•

Return the oil to the compressor.

•

Maintain a column of liquid at the expansion valve.

•

Minimize the loss of capacity.

•

Minimize the refrigerant charge in the system.

These piping practices are similar for R-410A and POE oil. However, because of the different mass
flows and pressures, the line diameter required to carry the oil and refrigerant may not be the same
as a similar tonnage R-22 unit. Also, the allowable pressure drop may be greater for R-410A than
R-22.
Evidence accumulated over years of observation demonstrates that the lower the refrigerant
charge, the more reliably a split air-conditioning system performs. Any amount of refrigerant in
excess of the minimum design charge becomes difficult to manage. The excess refrigerant tends
to collect in areas that can interfere with proper operation and eventually shortens the service life
of the system.
To successfully minimize the system refrigerant charge, the correct line size should be used and
the line length must be kept to a minimum.

Background
In a split air-conditioning system, the four major components of the refrigeration system are
connected by field-assembled refrigerant piping (Figure 1). A suction line connects the
evaporator to the compressor, the discharge line connects the compressor to the condenser, and
the liquid line connects the condenser to the expansion device, which is located near the
evaporator inlet. Operational problems can occur if these refrigerant lines are designed or
installed improperly.
.
Figure 1. Interconnecting refrigerant lines in a typical split air-conditioning system

SS-APG007-EN

Overview

The origin of the requirements for equivalent line lengths of components, line pressure drop, and
minimum and maximum refrigerant velocities is uncertain. It appears likely that at least some of
the supporting data was derived from measurements and/or equations involving water. Some
resource materials even show water components when illustrating refrigerant piping
requirements.
Subsequent reviews of analytical and empirical data for refrigerant piping resulted in the
publication of two research papers: Pressure Losses in Tubing, Pipe, and Fittings by R.J.S. Pigott
and Refrigerant Piping Systems — Refrigerants 12, 22, 500 by the American Society of
Refrigeration Engineers (ASRE). In his paper, Pigott described his use of refrigerant as the fluid
and his direct measurement of pressure drops. His findings indicated that the pressure drop of
many line components is small and difficult to measure. For these components, he used
experimental data to derive a formula relating the geometry of the component to its pressure
drop. Overall, his calculated pressure loss of the components was less than originally
determined.
The conclusion of the ASRE research paper stated that the minimum required velocity to
maintain oil entrainment in vertical risers and horizontal lines will vary with the diameter of the
tube and with the saturation temperature of the suction gas. In other words, the minimum
required velocity for oil entrainment is not constant.

Updated Guidelines
Liquid Lines
Historically, liquid lines were sized to minimize the pressure losses within the piping circuit. Oil
movement through the piping wasn’t a concern (nor is it today) because oil is miscible in liquid
refrigerant at normal liquid-line temperatures. The historic and traditional 6 psid liquid line
pressure drop had the unintended consequence of requiring line sizes with large internal
refrigerant volumes. Since our objective is also to minimize the refrigerant charge to make the
most reliable systems, we increased the allowable liquid pressure drop to 35 psid (R-22), which
allows for the selection of a smaller liquid line while still maintaining refrigeration operation.
With R-410A refrigerant and POE oil, this pressure drop can be as high as 50 psid. Within these
guidelines, refrigeration operation is maintained while minimizing the refrigerant charge. It is
still required to limit the liquid line velocity to 600 ft/min to help avoid issues with water hammer.

Suction Lines
R-410A is a high-pressure refrigerant and allows higher-pressure drops in the suction lines. With
R-22, a 2°F loss in the suction line means a pressure drop of 3 psi. With R-410A refrigerant, that
same 2°F loss is a 5 psi drop. Additional pressure drop may be tolerated in certain applications.
R-410A refrigerant suction lines must be sized to maintain oil-entrainment velocities in both the
horizontal and vertical risers. Oil entrainment for R-410A is based on suction temperature as well
as tube diameter. At the time of this writing, no known direct oil-entrainment tests have been
conducted. Trane has used ASHRAE data to create equation-based formulas to predict the
entrainment velocities of R-410A refrigerant and POE oil. These minimum velocities are reflected
in the line sizes listed in the component selection summary (Table 2, p. 18).

SS-APG007-EN

Overview

Equipment Placement
Minimize Distance Between Components
For a split air-conditioning system to perform as reliably and inexpensively as possible, the
refrigerant charge must be kept to a minimum. To help accomplish this design goal:
•

Site the outdoor unit as close to the indoor unit as possible.

•

Route each interconnecting refrigerant line by the shortest and most direct path so that line
lengths and riser heights are no longer than absolutely necessary.

•

Use only horizontal and vertical piping configurations.

•

Determine whether the total length of each refrigerant line requires Trane review. Be sure to
account for the difference in elevations of the indoor and outdoor units when calculating the
total line length.
Interconnecting lines of 150 lineal ft (45.7 m) or less do not require Trane review, but only a
limited amount may be in a riser (see Figure 2 and Figure 3).

.
Figure 2. Allowable elevation difference: Cooling-only RAUJ above indoor unit

RAUJ

Acceptable suction-riser height
based on total suction-line length
(RAUJ above indoor unit)

Figure 3. Allowable elevation difference: Cooling-only RAUJ below indoor unit

RAUJ

Acceptable liquid-riser height
based on total liquid-line length
(RAUJ below indoor unit)

SS-APG007-EN

Line Sizing, Routing, and Component Selection
Figure 4 illustrates an example of an RAUJ split-system component arrangement. Use it to
determine the proper, relative sequence of the components in the refrigerant lines that connect the
RAUJ condensing unit to an evaporator coil. Refer to “Examples of Field-Installed Evaporator
Piping,” p. 13, for more detailed schematics of evaporator piping. The RAUJ units are R-410A
machines, and all the selected components installed in the field must also be rated for use with
R-410A.
Figure 4.

Example of placement for split-system components
access port
manual
ball valve

condenser and
subcooler coil

discharge
line
manual
angle valves

filter

access
port
manual
ball valve

compressors

condensing unit

liquid line

check/relief valve
king valve access port

evaporator coil

coil module

expansion
valves
moistureindicating
sight glass

distributor
access port
Frostat™
control

solenoid
valve

access
port

filter drier
with
access port

manual
ball valve
manual ball valve
suction line

Liquid Lines
Line Sizing
Properly sizing the liquid line is critical to a reliable split-system application. Table 2, p. 18 shows
the recommended liquid-line sizing for each RAUJ model based on its nominal capacity. Using the
preselected tube diameter to uniformly size the liquid line will maintain operating requirements
and is the line size around which the RAUJ installation literature charging charts were generated.
Increasing the line size will not increase the allowable line length.

Routing
Install the liquid line with a slight slope in the direction of flow so that it can be routed with the
suction line.
A height limitation exists for liquid lines that include a liquid riser because of the loss of subcooling
that accompanies the pressure loss in the height of the liquid column. Figure 3, p. 3, depicts the
permissible rise in the liquid line (without excessive loss of subcooling). Again, system designs
outside the application envelope of the RAUJ unit require Trane review.
The RAUJ unit design includes a liquid line check/relief assembly at the outlet of the subcooler to
prevent liquid refrigerant from being drawn back to the compressor during the off cycle. The relief

SS-APG007-EN

Line Sizing, Routing, and Component Selection

valve discharges to the condenser to prevent excessive pressures from developing in the liquid line
during the off cycle, due to a temperature change of the trapped column of liquid between the
solenoid valve and check valve.

Insulation
The liquid line is generally warmer than the surrounding air, so it does not require insulation. In
fact, heat loss from the liquid line improves system capacity because it provides additional
subcooling. However, if the liquid line is routed through a high-temperature area, such as an attic
or a mechanical room, insulation would be required.

Components
Liquid-line refrigerant components necessary for a successful job include a filter drier, access port,
solenoid valve, moisture-indicating sight glass, expansion valve(s), and ball shutoff valves.
Figure 4, p. 4 illustrates how to sequence the components properly in the liquid line. Position the
components as close to the evaporator as possible. Table 2, p. 18, identifies suitable components,
by part number, for each RAUJ model. Note that there are two access ports: one located at the
RAUJ and one located at the evaporator. Table 3, p. 19, identifies a list of suitable expansion valves.

Liquid Filter Drier
There is no substitute for cleanliness during system installation. The liquid filter drier prevents
residual contaminants, introduced during installation, from entering the expansion valve and
solenoid valve. If choosing a filter other than the one listed in Table 2, make sure its volume,
filtering, and moisture-absorbing characteristics are equivalent, and that it is the replaceable core
type.

Access Port
The access port located at the RAUJ allows the unit to be charged with liquid refrigerant and is used
to determine charge level. This port is usually a Schraeder valve with a core.

Solenoid Valve
In RAUJ split systems, solenoid valves isolate the refrigerant from the evaporator during the off
cycles; under certain conditions, they may also trim the amount of active evaporator as the
compressors unload. Generally, the “trim” solenoid valve is unnecessary for VAV comfort-cooling
applications and is only required for constant-volume applications when dehumidification is a
special concern.
Note: RAUJ units with fin and tube condensers employ pumpdown, so isolation solenoids are
required. The suggested solenoid uses a 120-volt service and requires code-compliant
wiring to the RAUJ condensing unit.

Moisture-Indicating Sight Glass
Be sure to install one moisture-indicating sight glass in the main liquid line.
Note: The sole value of the glass is its moisture-indicating ability. Use the Installation manual
charging curves—not the sight glass—to determine proper charge levels. A properly
charged RAUJ unit may show bubbles in the sight glass.

Expansion Valve
The expansion valve is the throttling device that meters the refrigerant into the evaporator coil.
Metering too much refrigerant floods the compressor; metering too little elevates the compressor
temperature. Choosing the correct size and type of expansion valve is critical to ensure that it will
correctly meter refrigerant into the evaporator coil throughout the entire operating envelope of the
system. Correct refrigerant distribution into the coil requires an expansion valve for each
distributor.

SS-APG007-EN

Line Sizing, Routing, and Component Selection

For improved modulation, choose expansion valves with balanced port construction and external
equalization. Table 3, p. 19, identifies the part number of the valve suggested for commercial RAUJ
systems.
The tonnage of the valve should represent the tonnage of the portion of coil that the TXV/distributor
will feed.

Ball Shutoff Valves
Adding manual, ball-type shutoff valves upstream and downstream of the filter simplifies
replacement of the filter core. As a matter of practicality, Table 2, p. 18, lists only one of the
numerous manufacturers of these valves. If you choose a valve by another manufacturer, ensure
that its specifications are equivalent to the valve identified in this guide.

Suction Lines
Line Sizing
Proper line sizing is required to guarantee that the oil returns to the compressor throughout the
system’s operating envelope. At the same time, the line must be sized so that the pressure drop
does not excessively affect capacity or efficiency. To accomplish both objectives, it may be
necessary to use two different line diameters: one for the horizontal run and for the vertical drops,
and another for the vertical lifts (risers).
Note: Preselected suction-line diameters shown in Table 2 are independent of total line length for
properly charged 20-120 ton RAUJ units in normal air-conditioning applications.

Routing
To prevent residual or condensed refrigerant from “free-flowing” toward the compressor during
the off cycle, install the suction line so that it slopes by ¼ to 1 inch per 10 feet of run (1 cm per
3 m) toward the evaporator.
When the application includes a suction riser, oil must be forced to travel the height of the riser.
Riser traps are unnecessary in the suction line. They will add pressure drop. Double risers must not
be used. They not only add pressure drop but can hold great amounts of oil—oil better used in the
compressor.
All 20- through 120-ton RAUJ units unload such that a single line size, preselected in Table 2,
provides sufficient lift to entrain oil up the permissible riser height. To ensure proper oil movement,
the permissible unit separation is 150 ft (45.7 m), including a maximum vertical suction rise of 50 ft
(15 m). System designs outside this application envelope require Trane review.
Note: If a suction riser is properly sized, oil will return to the compressor regardless of whether
a trap is present. If a suction riser is oversized, adding a trap will not restore proper oil
entrainment.

Avoid Underground Refrigerant Lines
Refrigerant condensation during the off cycle, installation debris inside the line (including
condensed ambient moisture), service access, and abrasion/corrosion can quickly impair
reliability.

Insulation
Any heat that transfers from the surrounding air to the cooler suction lines increases the load on
the condenser (reducing the system’s air-conditioning capacity) and promotes condensate
formation. After operating the system and testing all fittings and joints to verify that the system is
leak-free, insulate suction lines to prevent heat gain and unwanted condensation.

SS-APG007-EN

Line Sizing, Routing, and Component Selection

Components
Installing the suction line requires field installation of these components: a filter, access port,
Frostat™ control for coil frost protection, and ball shutoff valve. Position them as close to the
compressor as possible. Table 2, p. 18, identifies suitable components by part number for each
RAUJ model.
Note: Placement of the Frostat control is illustrated in Figure 4, p. 4.

Filter
The suction filter prevents contaminants, introduced during installation, from entering the
compressor. For this reason, the suction filter should be the replaceable-core type, and a clean core
should be installed after the system is cleaned up.
As a matter of practicality, Table 2 lists only one of the many manufacturers of suction-line filters.
If you choose a filter by another manufacturer, ensure that its capability and volume are equivalent
to the suction filter identified in this guide.

Access Port
The access port is used to determine suction pressure. This port is usually a Schraeder valve with
a core.

Frostat™ Coil Frost Protection
The Frostat control is the preferred method for protecting the evaporator coils from freezing on
typical comfort cooling applications. It senses the suction-line temperature and temporarily
disables mechanical cooling if it detects frost conditions. The control is mechanically attached to
the outside of the refrigerant line, near the evaporator, and wired to the unit control panel.

Ball Shutoff Valve
Adding manual, ball-type shutoff valves upstream and downstream of the filter simplifies
replacement of the filter core.
As a matter of practicality, Table 2 lists only one of the numerous manufacturers of these valves.
If you choose a valve by another manufacturer, ensure that its specifications are equivalent to the
valve identified in this guide.

SS-APG007-EN

Expansion Valves
Expansion valves meter refrigerant into the evaporator under controlled conditions. If there is too
much refrigerant, the refrigerant will not completely vaporize and the remaining liquid will slug the
compressor. If there is too little refrigerant, there may not be enough cooling for the compressor.
Table 3, p. 19, lists expansion valves. Each evaporator distributor requires a dedicated expansion
valve in order to maintain proper coil distribution. The expansion valve should be selected to match
the capacity of the coil that the distributor feeds.
Example 1: 20-ton coil with two equal distributors
20 / 2 = 10
Each TXV should be selected for 10 tons.
Example 2: 30-ton coil with two distributors and a 60/40 coil split
30 x .6 = 18 and 30 x .4 = 12
One TXV should be sized for 18 tons, and one TXV should be sized for 12 tons.
If the coil or distributors have a difference of only one circuit tube, the difference should be ignored.
The proper balance for feeding refrigerant for a RAUJ system is to provide 18°F of superheat—the
difference between the saturated and actual refrigerant temperature leaving the evaporator.
Expansion valve superheat is preset from the factory at 12°F and needs to be reset to 18°F. Use the
turns listed in Table 1 to adjust them to the correct 18°F superheat.
Table 1.

Expansion valves

Sporlan
Field adjust for
18°F

Standard off-the-shelf nominal valve settings (90 PSIG air test setting)
Valve
ERZE
OZE

Superheat, °F
12

CW turns available
4.5

CCW turns
available
4.5

Superheat change
per turn
2.4°F

2 1/2 CW

3.4°F

1 3/4 CW

Other manufacturers of TXV are listed in the RAUJ installation literature along with similar
necessary adjustments for proper superheat.

SS-APG007-EN

Controls
The RAUJ unit is available with different control options depending on unit tonnage. These control
options include VAV operation, CV operation, chilled-water operation and a “no controls” option.
The no controls option is often selected when a controls contractor wants to stage the RAUJ
compressors.
It is important to understand that when the staging of compressors is turned over to a third party,
the compressor protection, provided through system stability, is also turned over to the third party.
Simply stated, this means that when a compressor turns on, it shouldn’t turn off until the expansion
valve comes under control. And, once the compressor turns off, it should be allowed to stay off until
the crank case heater has warmed up.
There are timers in the RAUJ unit compressor staging; however, they are not meant to accomplish
system stability. System stability must be programmed in the system controls. To accomplish this,
the system controls must incorporate a 5-minute-on, a 5-minute-off, and a 5-minuteinterstage differential on each compressor stage.

SS-APG007-EN

Hot Gas Bypass
Many years ago, hot gas bypass (HGBP) was successfully added to HVAC systems to correct a
number of operational problems. Hoping to avoid such problems altogether, it eventually became
common practice for designers to specify hot gas bypass in new systems. Unfortunately, the
practice often degraded rather than improved reliability.
Hot gas bypass increases the minimum refrigerant charge; it also inflates the first cost of the
system. Besides adding more paths for potential refrigerant leaks, hot gas bypass increases the
likelihood of refrigerant distribution problems. Finally, hot gas bypass uses excessive amounts of
energy by preventing the compressors from cycling with fluctuating loads.
Trane now has more than 15 years experience in the successful use of packaged rooftop equipment
without hot gas bypass in commercial comfort-cooling applications. To prevent evaporator freezeup, our equipment typically includes Trane® Frostat™ coil frost protection.
Like hot gas bypass, the Frostat system protects the coil from freezing, but it does so by turning
off compressors when a sensor detects the formation of frost on the evaporator coil. The
compressor is released to operate when the coil temperature rises a few degrees above the frost
threshold. The Frostat control strategy reduces the overall energy consumption of the system while
maintaining system control.
Systems should be designed to avoid HGBP whenever possible.
For more information about HGBP, refer to the Engineers Newsletter, “Hot Gas Bypass – Blessing
or a Curse?” (ADM-APN007-EN).

SS-APG007-EN

Remodel, Retrofit, or Replacement
Inevitably, older condensing units and evaporator systems will need to be replaced or retrofitted.
Due to the phase-out of many of these older refrigerants, the major components for those older
units or systems may no longer be available. The only option will be to convert the system to
R-410A, POE oil, and R-410A components.
When upgrading an existing refrigerant split system due to remodel, retrofit, or replacement, the
entire system must be reviewed for compatibility with R-410A and POE oil. Each and every part of
the split HVAC system MUST be compatible with the properties of R-410A refrigerant and POE oil.
In addition, ensure the existing electrical service is adequate for the product being installed.

SS-APG007-EN

•

R-22 condensing units will not work with R-410A; they must be replaced.

•

Most older evaporator coils were not pressure- and cycle-rated for R-410A pressures. If they
weren’t, they will need to be replaced. If they were properly pressure-rated for R-410A, existing
coils must be modeled to determine if they will meet capacity requirements, are properly
circuited, have correctly sized distributor tubes, and employ acceptable distributors and
orifices.

•

The required R-410A line sizes may be different than the existing line sizes. The lines need to
be re-sized and compared to existing lines for reusability.

•

Suction lines 2-5/8 OD and smaller of type L copper are suitable for use with R-410A. Suction
lines 3-1/8 OD must use type K or thicker wall.

•

Discharge lines, liquid lines, heat pump vapor lines, and hot gas bypass lines 1-3/8 OD and
smaller of type L copper are suitable for use with R-410A. These same lines sized at 1-5/8 OD
or 2-1/8 OD must use type K or thicker wall.

•

Expansion valves need to be reselected. Expansion valves are refrigerant specific.

•

Any gasket or o-ring should be replaced. Shrinkage of the original seal may occur after an HFC
conversion, potentially causing a refrigerant leak. Components commonly affected are
Schraeder cores, solenoid valves, ball valves, and flange seals. But all external seals in contact
with refrigerant should be viewed as potential leak sources after a retrofit.

•

All other valves, filters, valve packing, pressure controls, and refrigeration accessories must be
researched through their manufacturer for compatibility with the pressures of an R-410A
system, and for their compatibility with the newer POE oil.

•

For the best performance and operation, the original mineral oil should be removed from the
components of the system that are not being replaced. Any component of the system that is
suspected of trapping oil (piping, traps, and coil), should be dismantled, drained, and
reassembled. After all components have been drained, the amount of residual mineral oil will
have a negligible effect on performance and reliability.

Remodel, Retrofit, or Replacement

NOTICE:
Compressor Damage!
POE oil is hygroscopic – it absorbs water directly from the air. This water is nearly impossible
to remove from the compressor oil and can cause compressor failures. For this reason, the
system should not be open for longer than necessary, dry nitrogen should flow in the system
while brazing, and only new containers of oil should be used for service and maintenance.
All Codes take precedence over anything written here.

SS-APG007-EN

Examples of Field-Installed Evaporator Piping
Single-Circuit RAUJs
Figure 5. Type UF evaporator coil with one distributor
1.

Pitch the liquid line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Provide one expansion valve per distributor.

Slightly pitch the outlet line from the suction
header toward the suction riser — that is,
1 in. / 10 ft (1 cm / 3 m) in the direction of flow.
Use the tube diameter that matches the
suction-header connection.

Evaporator Coil with
Standard Circuiting
suction line

Use the tube diameter recommended for a
vertical rise in Table 2, p. 18. Ensure that the
top of the riser is higher than the evaporator
coil.

Pitch the suction line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Insulate the suction line.

liquid
line

sight
glass

thermal
expansion
valve (TXV)

solenoid
valve

filter drier

distributor

Figure 6. Type UF evaporator coil with two distributors
1.

Pitch the liquid line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Provide one expansion valve per distributor.

“trim”
solenoid valve

thermal
expansion
valve (TXV)

Use the “horizontal” tube diameter
identified in Table 2, p. 18.

Use the tube diameter recommended for a
vertical rise in Table 2. Ensure that the top of
the riser is higher than the evaporator coil.

Pitch the suction line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Insulate the suction line.

Only use a “trim” solenoid valve for
constant-volume, humidity-sensitive
applications. For all other applications,
install a single solenoid valve (the “pumpdown” solenoid valve) between the liquidline filter drier and the sight glass.

SS-APG007-EN

liquid
line
sight
glass

filter drier

This looks like a trap, but is actually due to
the requirement that the refrigerant gas
leaving the coil flows downward, past the
lowest suction-header outlet, before turning
upward.

Evaporator Coil
with Horizontal-Split
(Standard) Circuiting

suction line

“pump-down”
solenoid valve
distributor

Evaporator Coil with
Intertwined Circuiting

suction line
liquid
line
sight
glass

thermal
expansion
valve (TXV)
distributor

solenoid
filter drier
valve

Examples of Field-Installed Evaporator Piping

Figure 7.
1.

Type UF evaporator coil with four distributors

Pitch the liquid line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Provide one expansion valve per distributor.

suction line

liquid
line
“trim”
solenoid valve

This looks like a trap, but is actually due to
the requirement that the refrigerant gas
leaving the coil flows downward, past the
lowest suction-header outlet, before turning
upward. Use a double-elbow configuration
to isolate the TXV bulb from other suction
headers.

Use the “horizontal” tube diameter
identified in Table 2, p. 18.

Use the tube diameter recommended for a
vertical rise in Table 2. Ensure that the top of
the riser is higher than the evaporator coil.

Pitch the suction line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Insulate the suction line.

Evaporator Coil
with Horizontal-Split
(Standard) Circuiting

thermal expansion
valves (TXV)

sight
glass

filter drier
“pumpdown”
solenoid valve
distributor

suction line
thermal expansion
valves (TXV)

Evaporator Coil with
Intertwined Circuiting

“trim”
solenoid valve
liquid
line
sight
glass

filter drier
“pumpdown”
solenoid valve

distributor

SS-APG007-EN

Examples of Field-Installed Evaporator Piping

Dual-Circuit RAUJs
Figure 8. Type UF evaporator coil with two distributors
1.

Pitch the liquid lines slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Provide one expansion valve per distributor.

The top of the Circuit 1 suction riser must be
higher than the bottom evaporator coil. Use
the tube diameter recommended for a
vertical rise in Table 2, p. 18.

The top of the Circuit 2 suction riser must be
higher than the top evaporator coil. Use the
tube diameter recommended for a vertical
rise in Table 2.

Pitch the suction lines slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Insulate the suction lines.

SS-APG007-EN

suction line
(circuit 2)
liquid line
(circuit 2)

Evaporator Coil
with Horizontal-Split
(Standard) Circuiting

sight
glass

suction line
(circuit 1)

distributor

solenoid
valve
liquid line
(circuit 1)

thermal
expansion
valve (TXV)

filter drier

Examples of Field-Installed Evaporator Piping

Figure 9. Type UF evaporator coil with four distributors
1.

Pitch the liquid line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

Provide one expansion valve per distributor.

Use the “horizontal” tube diameter
identified in Table 2, p. 18.

Use the tube diameter recommended for a
vertical rise in Table 2. Ensure that the top of
the riser is higher than the evaporator coil.

Insulate the suction line.

The top of the Circuit 1 suction riser must be
higher than the bottom evaporator coil. Use
the tube diameter recommended for a
vertical rise in Table 2.

10. The top of the Circuit 2 suction riser must be
higher than the top evaporator coil. Use the
tube diameter recommended for a vertical
rise in Table 2.

thermal expansion
valves (TXV)

suction line
(circuit 1)

solenoid
valve

liquid line
(circuit 2)

sight
glass
liquid line
(circuit 1)

filter drier

distributor

Evaporator Coil with
Intertwined Circuiting

suction lines
(circuit 1)

Pitch the suction line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

suction line
(circuit 2)

(circuit 2)

Evaporator Coil
with Horizontal-Split
(Standard) Circuiting

thermal expansion
valves (TXV)

liquid line
(circuit 2)
sight
glass
solenoid
valve

liquid line
(circuit 1)

filter drier

distributor

SS-APG007-EN

Examples of Field-Installed Evaporator Piping

Figure 10. Type UF evaporator coil with eight distributors

2 Provide one expansion valve per distributor.
3 Slightly pitch the outlet line from the suction
header toward the suction riser — that is,
1 in. / 10 ft (1 cm / 3 m) in the direction of flow.
Use the tube diameter that matches the
suction-header connection.

5 Use the “horizontal” tube diameter
identified in Table 2, p. 18.

thermal expansion
valves (TXV)
sight
glass

suction line
“trim”
solenoid valve
liquid line
(circuit 1)

6 Use the tube diameter recommended for a
vertical rise in Table 2. Ensure that the top of
the riser is higher than the evaporator coil.

“pump-down”
solenoid valve

7 Pitch the suction line slightly — 1 in. / 10 ft
(1 cm / 3 m) — so that the refrigerant drains
toward the evaporator.

distributor

Evaporator Coil with
Intertwined Circuiting

suction lines

8 Insulate the suction line.

(circuit 1)

10 The top of the Circuit 2 suction riser must be
higher than the top evaporator coil. Use the
tube diameter recommended for a vertical
rise in Table 2.

(circuit 2)

9 The top of the Circuit 1 suction riser must be
higher than the bottom evaporator coil. Use
the tube diameter recommended for a
vertical rise in Table 2.

liquid line
(circuit 2)

filter drier

(circuit 1)

4 This looks like a trap, but is actually due to
the requirement that the refrigerant gas
leaving the coil flows downward, past the
lowest suction-header outlet, before turning
upward. Use a double-elbow configuration
to isolate the TXV bulb from other suction
headers.

Evaporator Coil
with Horizontal-Split
(Standard) Circuiting

suction line
(circuit 2)

1 Pitch the liquid line slightly — 1 in. / 10 ft
(1 cm / 3 m)— so that the refrigerant drains
toward the evaporator.

thermal expansion
valves (TXV)

“trim”
solenoid valve

11 Only use a “trim” solenoid valve for
constant-volume, humidity-sensitive
applications. For all other applications,
install a single solenoid valve (the “pumpdown” solenoid valve) between the liquidline filter drier and the sight glass.

liquid line
(circuit 2)
sight
glass
liquid line
(circuit 1)

filter drier

“pump-down”
solenoid valve

distributor
‘

SS-APG007-EN

Parts
Table 2.

Component selection summary

UNIT
Refrigerant ckts
Minimum step (tons)

RAUJC20

RAUJC25

RAUJC30

RAUJC40

RAUJC50

RAUJC60

11.7

SUCTION LINE

RAUJC80 RAUJD100 RAUJD120

SUCTION LINE

Tube diameter (in.)
Horizontal (& drops)

1 5/8

2 1/8

1 5/8

2 1/8

2 5/8

Vertical (up)

1 5/8

2 1/8

1 5/8

2 1/8

DHY01086

FLR06122

DHY01086

FLR06122

FLR06123

FLR06124

ELM03572

ELM03572
(QTY 2)

Filter shell 1/ckt
Filter core per shell

Access port 3/ckt(a)

ELM03572

Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
valve w/core valve w/core valve w/core valve w/core valve w/core valve w/core valve w/core valve w/core valve w/core

Frostat™ control

KIT01387

Ball valve 2/ckt (in.)

VAL09077

VAL09078

VAL09077

VAL09078

VAL06647

1 1/8

LIQUID LINE
Tube diameter (in.)
Filter shell

1/ckt(b)

LIQUID LINE
5/8

7/8

5/8

7/8

DHY01263

DHY01151

COR00102
(QTY 2)

Filter core per shell

COR00102

COR00102
(QTY 2)

Solenoid valve, coil
1/ckt(c)

VAL09133
COL01884

VAL09100
COL01884

VAL09133
COL01884

VAL09100
COL01884

VAL09135
COL01884

VAL09485
COL12786

Sight glass 1/ckt

GLS00830

GLS00831

GLS00830

GLS00831

GLS00832

Access port 2/ckt(a)

Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
Schraeder
valve w/
valve w/core valve w/core valve w/core valve w/core valve w/core valve w/core valve w/core valve w/core
core

Ball valve 2/ckt (in.)

VAL07197

VAL07198

VAL07197

VAL07198

VAL07337

RAUJC20

RAUJC25

RAUJC30

RAUJC40

RAUJC50

RAUJC60

RAUJC80 RAUJD100 RAUJD120

VAL07337

(a) Valve body VAL01483, valve core COR00006, valve cap CAP00072
(b) 7/8” connection size
(c) For outdoor application, request junction box conduit boss, NEMA 4 watertight.

SS-APG007-EN

Parts

Table 3.

SS-APG007-EN

Expansion valves for RAUJ 20- through 120-ton application

Refrigerant

Manufacturer

Tonnage Range

Model Number

R-410A

Sporlan

2-3

ERZE-2-ZGA

Trane Part
VAL09476

R-410A

Sporlan

3-4

ERZE-3-ZGA

VAL09477

R-410A

Sporlan

4-5

ERZE-4-ZGA

VAL09478

R-410A

Sporlan

5-6

ERZE-5-ZGA

VAL09479
VAL09480

R-410A

Sporlan

6-7

ERZE-6-ZGA

R-410A

Sporlan

7-10

ERZE-8-ZGA

VAL09481

R-410A

Sporlan

10-13

ERZE-12-1/2-ZGA

VAL09482

R-410A

Sporlan

13-16

ERZE-15-ZGA

VAL09483

R-410A

Sporlan

16-23

OZE-20-ZGA

VAL09585

R-410A

Sporlan

23-28

OZE-25-ZGA

VAL09583

R-410A

Sporlan

28-40

OZE-35-ZGA

VAL09584

R-410A

Sporlan

40-60

OZE-50-ZGA

VAL09153

R-410A

Sporlan

60-70

OZE-60-ZGA

VAL09154

Trane optimizes the performance of homes and buildings around the world. A business of Ingersoll Rand, the
leader in creating and sustaining safe, comfortable and energy efficient environments, Trane offers a broad
portfolio of advanced controls and HVAC systems, comprehensive building services, and parts. For more
information, visit www.Trane.com.
Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.
© 2012 Trane All rights reserved
SS-APG007-EN 19 Mar 2012

We are committed to using environmentally

Supersedes SS-APG007-EN (Sep 2009)

conscious print practices that reduce waste.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Paul Solberg
Create Date                     : 2012:03:19 16:03:17Z
Keywords                        : "RAUJ, split, R-410A, Tube size, Component selection"
Modify Date                     : 2012:03:23 10:04:55-05:00
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : SS-APG007-EN (10/11):  Application Guide - Tube Size and Component Selection, RAUJ Split Systems (20-120 Tons) using R-410A
Creator                         : Paul Solberg, Beth Bakkum
Description                     : Application Guide - Tube Size and Component Selection, RAUJ Split Systems (20-120 Tons) using R-410A
Subject                         : RAUJ, split, R-410A, Tube size, Component selection
Creator Tool                    : FrameMaker 10.0.1
Metadata Date                   : 2012:03:23 10:04:55-05:00
Producer                        : Acrobat Distiller 10.1.2 (Windows)
Document ID                     : uuid:799de84e-cbdc-4d5b-a44e-9a06c6e6324b
Instance ID                     : uuid:03209f6a-e3d2-46bd-a7af-f345b72e687d
Page Mode                       : UseNone
Page Count                      : 28

EXIF Metadata provided by EXIF.tools

Trane Rauj Cauj 20 To 120 Tons Installation And Maintenance Manual SS APG007 EN (10/11)

Navigation menu

Versions of this User Manual:

Views

Navigation