Trane Xv95 Owner S Manual

Trane-Xb90-Owner-S-Manual trane-xb90-owner-s-manual

Trane-Xv80-Owner-S-Manual trane-xv80-owner-s-manual

Trane-Xc95M-Owner-S-Manual trane-xc95m-owner-s-manual

Trane-Xl80-Owner-S-Manual trane-xl80-owner-s-manual

Trane-Xl95-Owner-S-Manual trane-xl95-owner-s-manual

2014-07-06

: Trane Trane-Xv95-Owner-S-Manual trane-xv95-owner-s-manual trane pdf

Open the PDF directly: View PDF .
Page Count: 12

Owner's Guide

Indoor Units:

Air Handlers

Gas Furnaces

32-5064-WEB01

2 32-5064-WEB01

Proper Maintenance – Air Handlers

How to remove the ﬁlter from your Air Handler.

Ask your dealer where the ﬁlter is located when your system

is installed. It may be behind the bottom panel of your indoor

unit. Or it may be at the top, bottom, or either side. Or there

may be two ﬁlters.

In any case, removing a ﬁlter is easy. Just make sure you insert

the clean ﬁlter with the arrows on it pointing in the direction

of the airﬂow.

Your installing dealer is your best source of filter and

maintenance information.

To prevent injury or death, or property damage, read and follow all

instructions and warnings, including labels shipped with or attached

to unit before operating your new air conditioning system.

If heating system is not operational during the cold weather

months, provisions must be taken to prevent freeze-up of

all water pipes and water receptacles. This is very important

during times of vacancy.

Although special care has been taken to minimize sharp edges

in the construction of the unit, be extremely careful when

handling parts or reaching into the unit.

Improper installation, adjustment, alteration, service maintenance,

or use can cause explosion, ﬁre, electrical shock, or other conditions

which may cause personal injury or property damage. Consult a

qualiﬁed installer or service agency for information or assistance.

The qualiﬁed installer or agency must use factory-authorized kits or

accessories when modifying this product.

Disconnect all electric power to the indoor air handler or furnace

before removing access panels to perform any maintenance.

Disconnect power to both the indoor and outdoor units.

A clean ﬁlter saves money.

Help ensure top efﬁciency by cleaning the ﬁlter regularly.

When the unit circulates and ﬁlters the air in your home, dust

and dirt particles collect on the ﬁlter located in your indoor unit.

Excessive buildup forces the system to run longer to maintain your

set temperature. And you end up paying for it.

Don’t waste money heating and cooling

when you don’t need to.

When you’re going to be away from home for a few days –

or when outdoor temperatures are moderate – don’t let your

system run unnecessarily. Lower the thermostat to 55°F in the

winter. And raise it to 85°F in summer. Then when you return –

or when temperatures dictate – you can reset the system and it

will immediately begin making your home comfortable again.

Continuous fan mode during cooling operation may not be

appropriate in humid climates. If the indoor air exceeds 60%

relative humidity or simply feels uncomfortably humid, it is

recommended that the fan only be used in the AUTO mode.

Never stop the system by shutting off the main power.

If the main power is ever disconnected for more than three

hours, turn off the thermostat. Then wait for at least three more

hours after the power has been restored before turning the

thermostat back on. Failure to follow this procedure could result

in damage to your system.

Clean or replace your ﬁlter at least once a month or

twice a month when the system is running more.

If you have a semi-permanent

ﬁlter, you can take the ﬁlter out of

the frame and vacuum it. Where

disposable ﬁlters are used, they

must be replaced every month

with the same size as originally

supplied.

Both methods are quick and easy

and guaranteed to cut the energy

used by your system. When replacing your air handler ﬁlters,

always use the same size and type that was originally supplied.

Filters are available from your dealer.

Cut operating costs by keeping snow, ice and debris clear

of your outdoor heat pump unit.

NOTE: Condensation may occur on the surface of the air

handler when installed in an unconditioned location.

Efﬁcient operation of your outdoor unit requires the free ﬂow

of air over the coils. Anything that blocks this ﬂow forces the

unit to work harder to do its job. At no time should anything be

stacked against the side of the outdoor unit or draped over it.

Keeping it clear of debris helps it work at peak efﬁciency, and

that helps hold down operating costs.

Locate access door marked

"FILTER" and lift up the open

side of the levers.

Slide dirty ﬁlter out, replace with a

new ﬁlter making sure the arrows

printed on it are pointing in the

direction of airﬂow.

Hold the "FILTER" door ﬁrmly in

place and snap the levers down

(closed).

Your ﬁlter may

or may not be

framed.

For regular dealer maintenance please refer to

www.acca.org/industry/quality

3 32-5064-WEB01

Before you call for service, check the following:

Problem Possible cause Possible Remedy

Insufﬁcient heating or cooling 1. Dirty ﬁlters

2. Air not circulating freely

3. Blocked outdoor coil

1. Clean or replace

2. Check supply registers and return grills for blockage

3. Clear away leaves or other debris

Failure to operate 1. Power off

2. Open circuit breaker or burned‑out fuses

3. Improperly adjusted thermostat

1. Make sure main switch is in on position

2. Reset circuit breaker, or replace burned‑out fuses

3. Check setting, adjust thermostat

Unusual Noise Call your local servicer

The Problem Solver – Air Handlers

NOTE: Improperly sized vents can cause the formation of

condensate, combustion gas leakage and spillage, and an

inoperable furnace.

This unit is not a household appliance. It is a complex

self-contained system that requires professional maintenance

and repair. That’s why attempts at do it yourself repairs on an

in-warranty unit may void the remainder of your warranty. Other

than performing the simple maintenance recommended in this

manual, you should not attempt to make any adjustments to

your system.

NOTE: The blower motor bearings are factory lubricated and

under normal operating conditions usually do not require

servicing. Your local servicer can advise you if oiling is required.

Your dealer should be able to take care of any questions or

problems you may have.

Keep your unit looking like new for years.

Clean the enamel ﬁnish of your unit with ordinary soap and water.

For stubborn grease spots, use a household detergent. Lacquer

thinner or other synthetic solvents may damage the ﬁnish.

Just set the temperature you want.

Set temperatures by using the indicators on the thermostat*

control. After that, your comfort control center (thermostat) will

maintain a constant indoor temperature, regardless of changes

in outdoor temperatures. Read your thermostat manual for

directions on setting the temperatures.

Save energy with an electronic programmable thermostat.

With an electronic programmable thermostat* energy savings is

easy. Just program the thermostat for the temperatures you are

most comfortable with and it will automatically change settings

up to four times a day. Special weekend and vacation schedules

are also easily programmed for comfort and savings. Read your

thermostat manual for programming instructions. If you want

the optimum balance between comfort and the cost of running

your system, we recommend keeping the temperature settings

at 68°F for heating and 78°F for cooling.

Save energy by letting the thermostat do its job. Once you

set the thermostat, keep subsequent adjustments to a minimum.

Adjust it only when a new program is needed.

*Optional accessory

Whenever your house is to be vacant, arrange to have

someone inspect your house for proper temperature. This

is very important in below freezing weather. If for any reason

your unit should fail to operate, damage could result, such

as frozen water pipes.

Subject to the terms and conditions of this limited warranty, Trane U.S., Inc. (“Company’) extends

a limited warranty against manufacturing defects for the product(s) identied in Table 1 attached hereto

(“Products’) that are installed in a residential application (personal, family or household purposes) under

normal use and maintenance in the United States and Canada.

This limited warranty applies to Products manufactured on or after August 1, 2011.

In order to maximize the available benets under this limited warranty, the Purchaser (as dened

below) should read it in its entirety. All repairs of Product parts covered under this limited warranty must

be made with authorized service parts and by a licensed HVAC service provider. Additionally, commercial

applications are treated differently under this limited warranty as stated in Table 1 attached hereto. For

purposes of this limited warranty, “commercial applications” shall mean any application other than for

personal, family, or household use.

TERM: The limited warranty period for Products is as stated in Table 1 attached hereto. If the Pur-

chaser properly registers the Products, the limited warranty period shall be extended as stated in Table 1

attached hereto. Regardless of registration, the Commencement Date for a limited warranty period shall

be the date that the original installation is complete and all Product start-up procedures have been prop-

erly completed and veried by an installer’s invoice. If the installation and start-up date cannot be veried

by the installer’s invoice, the Commencement Date shall be sixty (60) days after the factory manufacture

date which is veried by the Product serial number. Where a Product is installed in a newly constructed

home, the Commencement Date is the date the Purchaser purchased the residence from the builder.

Proof of Product purchase, installation, and/or closing date of the residence may be required to conrm

the Commencement Date.

The installation of Product replacement parts under this limited warranty shall not extend the original

warranty period. The warranty period for any Product part replaced under this limited warranty is the ap-

plicable warranty period remaining under the original Product warranty.

WHO IS COVERED: This limited warranty is provided only to the original owner and his or her

spouse (“Purchaser’) of the residence where the Products are originally installed. This warranty is not

transferable except according to terms stated on the applicable website identied below under Registra-

tion Requirements. Company has the right to request any and all proof of Product purchase or installation

and/or closing date of the residence.

WHAT COMPANY WILL DO: Company may request proof of Product purchase and/or installa-

tion in order to provide Product parts under this limited warranty. As Company’s only responsibility and

Purchaser’s only remedy under this limited warranty, Company will furnish a replacement part to the

licensed HVAC service provider, without charge for the part only, to replace any Product part that fails

due to a manufacturing defect under normal use and maintenance. The Purchaser must pay for any

and all shipping and handling charges and other costs of warranty service for the replacement part. If a

Product part is not available, Company will, at its option, provide a free suitable substitute part or provide

a credit in the amount of the then factory selling price for a new suitable substitute part to be used by the

Purchaser towards the retail purchase price of a new Company product. Any new Product purchase shall

be at Purchaser’s sole cost and expense including, but not limited to, all shipping, removal, and installa-

tion costs and expenses.

REGISTRATION REQUIREMENTS: All Products must be properly registered online by the Purchaser

within sixty (60) days after the Commencement Date to receive the registered limited warranty terms. To

http://www.trane.com/Residential/Trane/Owners/Warranty-Information or

http://www.americanstandardair.com/sevicesupport/pages/warranty.aspx

and click “Begin Online Registration.” If a Purchaser does not register within this stated time period,

the base limited warranty terms shall apply.

ELIGIBILITY REQUIREMENTS: The following items are required in order for the Products to be

covered under this limited warranty:

• The Products must be in the same location where they were originally installed.

• The Products must be properly installed, operated, and maintained by a licensed HVAC service

provider in accordance with the Product specications or installation, operation, and maintenance

instructions provided by Company with each Product. Failure to conform to such specications and/

or instructions shall void this limited warranty. Company may request written documentation showing

the proper preventative maintenance.

• All Product parts replaced by Company under this limited warranty must be given to the servicing

provider for return to Company.

• Air handlers, air conditioners, heat pumps, cased or uncased coils and stand-alone furnaces must

be part of an Air Conditioning, Heating, and Refrigeration Institute rated and matched system or a

specication in a Company provided bulletin or otherwise approved in writing by a Company autho-

rized representative.

EXCLUSIONS: The following are not covered by this limited warranty:

• Labor costs including, but not limited to, costs for diagnostic calls or the removal and reinstallation of

Products and/or Product parts.

• Shipping and freight expenses required to ship Product replacement parts.

• Failures, defects, or damage (including, but not limited to, any loss of data or property) caused by (1)

any third party product, service, or system connected or used in conjunction with the Products; (2)

any use that is not designed or intended for the Products; (3) modication, alteration, abuse, misuse,

negligence, or accident; (4) improper storage, installation, maintenance, or operation including, but

not limited to, operation of electrical equipment at voltages other than the range specied on the

Product nameplate; (5) any use in violation of written instructions or specications provided by Com-

pany; (6) any acts of God including, but not limited to, re, water, storms, lightning, or earthquakes;

or any theft or riots; or (7) a corrosive atmosphere or contact with corrosive materials such as, but

not limited to, chlorine, uorine, salt (provided that indoor and outdoor coils will only be covered if

a Sea Coast Kit is installed), sulfur, recycled waste water, urine, fertilizers, rust, or other damaging

substances or chemicals.

• Products purchased direct including, but not limited to, Internet or auction purchases and purchases

made on an uninstalled basis.

• 3 phase models, cabinets or cabinet pieces that do not affect product performance, air lters, refrig-

erant, refrigerant line sets, belts, wiring, fuses, surge protection devices, non-factory installed driers,

and Product accessories.

• Increased utility usage costs.

REFRIGERANT POLICY: Beginning on January 1, 2010, R-22 refrigerant will no longer be used

as a manufacturer-installed refrigerant as required by federal regulation. Any and all expenses or costs

associated with replacing Product parts that are not R-410A compatible will not be covered by the terms

and conditions of this limited warranty. In addition, all Products containing R-410A refrigerant include a

liquid line lter drier which must be replaced when a compressor replacement is necessary. A suction line

lter drier must be added for compressors dened as burnouts. Failure to comply with such lter drier

requirements or the use of contaminated or alternate refrigerant or any non-approved refrigerant system

additives including, but not limited to, dyes, will void this limited warranty.

ADDITIONAL TERMS:

THIS LIMITED WARRANTY AND LIABILITY SET FORTH HEREIN ARE IN LIEU OF ALL OTHER

WARRANTIES AND LIABILITIES, WHETHER IN CONTRACT OR IN NEGLIGENCE, EXPRESS OR

IMPLIED, IN LAW OR IN FACT. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE APPLICABLE PRODUCT

WARRANTY. COMPANY DOES NOT AUTHORIZE ANY PERSON TO CREATE FOR IT ANY OBLIGA-

TION OR LIABILITY IN CONNECTION WITH THE PRODUCTS.

NOTWITHSTANDING ANYTHING IN THIS LIMITED WARRANTY TO THE CONTRARY, COMPANY

SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL AND/OR

PUNITIVE DAMAGES, WHETHER BASED ON CONTRACT, WARRANTY, TORT (INCLUDING, BUT

NOT LIMITED TO, STRICT LIABILITY OR NEGLIGENCE), PATENT INFRINGEMENT, OR OTHER-

WISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. COMPANY’S MAXIMUM

LIABILITY HEREUNDER IS LIMITED TO THE ORIGINAL PURCHASE PRICE OF THE PRODUCTS.

No action arising out of any claimed breach of this limited warranty may be brought by a Purchaser

more than one (1) year after the cause of action has arisen.

This limited warranty gives you specic legal rights, and you may also have other rights as otherwise

permitted by law. If this Product is considered a consumer product, please be advised that some local

laws do not allow limitations on incidental or consequential damages, how long a warranty lasts based on

registration, or how long an implied warranty lasts, so that the above limitations may not fully apply. Refer

to your local laws for your specic rights under this limited warranty.

Residential Systems

6200 Troup Highway, Tyler, TX 75707

Attn: Customer Relations

Or visit our website at www.trane.com or www.americanstandardair.com

GW-654-3111

Limited Warranty Information

5 32-5064-WEB01

Safety Section – Gas Furnaces

Safety signal words are used to designate a degree or level

of seriousness associated with a particular hazard. The signal

words for safety markings are WARNING and CAUTION.

a. WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

b. CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury. It is also used to alert against unsafe practices

and hazards involving only property damage.

IMPORTANT: Users MUST read all instructions in the manual. All manuals MUST be kept for future reference.

EXPLOSION HAZARD

Do not use this unit if any part has been under water. A ﬂood

damaged unit is extremely dangerous. Attempts to use the

furnace can result in ﬁre or explosion. A qualiﬁed service

agency should be contacted to inspect the furnace and to

replace all gas controls, control system parts, electrical parts

that have been wet or the furnace if deemed necessary.

Failure to follow this warning could result in property damage,

personal injury or death.

FIRE OR EXPLOSION HAZARD

If the information in this manual is not followed exactly, a ﬁre or

explosion may result causing property damage, personal injury

or loss of life.

— Do NOT store or use gasoline or other ﬂammable vapors

and liquids or combustible materials in the vicinity of this or

any other appliance.

— WHAT TO DO IF YOU SMELL GAS

 •Donottrytolightanyappliance.

 •Donottouchanyelectricalswitch;donotuseanyphonein

your building.

 •Immediatelycallyourgassupplierfromaneighbor’sphone.

Followthegassupplier’sinstructions.

 •Ifyoucannotreachyourgassupplier,callthere

department.

— DO NOT RELY ON SMELL ALONE TO DETECT LEAKS.

DUE TO VARIOUS FACTORS, YOU MAY NOT BE ABLE

TO SMELL FUEL GASES.

 •U.L.recognizedfuelgasandCOdetectorsarerecommended

in all applications, and their installation should be in accordance

with the manufacturer's recommendations and/or local laws,

rules, regulations, or customs.

— Installation and service must be performed by a qualiﬁed

installer, service agency or the gas supplier.

EXPLOSION HAZARD

In the event that electrical, fuel or mechanical failures occur,

shut off the gas supply at the manual gas shut off valve, located

on the supply gas piping coming into the furnace, before

turning off the electrical power to the furnace. Contact servicer.

Failure to follow this warning could result in property damage,

personal injury or death.

CARBON MONOXIDE POISONING HAZARD

Failure to follow the installation and operation instructions for

the venting system’s operation could result in carbon monoxide

poisoning or death.

EXPLOSION HAZARD

Should overheating occur, or the gas supply fail to shut off, shut

off the manual gas valve to the furnace before shutting off the

electrical supply.

Failure to follow this warning could result in property damage,

personal injury or death.

ThefollowingwarningcomplieswithStateofCalifornialaw,Proposition65.

THIS PRODUCT CONTAINS FIBERGLASS WOOL INSULATION!

Fiberglass dust and ceramic ﬁbers are believed by the State of

California to cause cancer through inhalation. Glasswool ﬁbers

may also cause respiratory, skin, or eye irritation.

PRECAUTIONARY MEASURES

 •Avoidbreathingberglassdust.

 •UseaNIOSHapproveddust/mistrespirator.

 •Avoidcontactwiththeskinoreyes.Wearlong-sleeved,

loose-ﬁtting clothing, gloves, and eye protection.

 •Washclothesseparatelyfromotherclothing:rinsewasher

thoroughly.

 •Operationssuchassawing,blowing,tear-out,andspraying

may generate ﬁber concentrations requiring additional

respiratoryprotection.UsetheappropriateNIOSH

approved respirator in these situations.

FIRST AID MEASURES

Eye Contact – Flush eyes with water to remove dust. If

symptoms persist, seek medical attention.

Skin Contact – Wash affected areas gently with soap and

warm water after handling.

SAFETY HAZARD

Bodily injury can result from high voltage electrical components,

fast moving fans, and combustible gas. During installation and

servicing, the electrical supply must be dis connected and the

main gas valve must be turned off.

Failure to follow this warning could result in property damage,

personal injury or death.

6 32-5064-WEB01

Safety Section – Gas Furnaces

BURN HAZARD

Do not attempt to manually light the furnace. Failure to follow

this warning could result in property damage, personal injury

or death.

The furnace is equipped with a blocked vent shut-off system.

When the furnace vent is blocked, a pressure switch will shut

off the furnace. Call a qualiﬁed servicer.

SAFETY HAZARD

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. See regular

maintenance on page 9 for annual general inspection. For

assistance or additional information consult a qualiﬁed installer,

service agency or the gas supplier. Failure to follow this warning

could result in property damage, personal injury or death.

EXPLOSION HAZARD

Propane gas is heavier than air and may collect in any low areas

or conﬁned spaces. In addition, odorant fade may make the gas

undetectable except with a warning device. If the gas furnace is

installed in a basement, an excavated area or a conﬁned space, it

is strongly recommended to contact a gas supplier to install a gas

detecting warning device in case of a gas leak. The manufacturer

of your furnace does not test any detectors and makes no

representations regarding any brand or type of detector.

Never operate your unit for either heating or cooling with

ﬁlters removed.

SAFETY HAZARD

Sharp Edge Hazard. Be careful of sharp edges on equipment

or any cuts made on sheet metal while installing or servicing.

Personal injury may result.

ELECTRIC SHOCK HAZARD

These servicing instructions are for use by qualiﬁed personnel only.

To reduce the risk of electric shock, do not perform any servicing

other than that contained in these operating instructions unless

you are qualiﬁed to do so.

Failure to follow this warning could result in property damage,

personal injury or death.

CARBON MONOXIDE HAZARD

For proper and safe operation of the furnace, air for combustion

and ventilation must be provided. Do not block or obstruct air

openings on the furnace, air openings to the area in which the

furnace is installed, or the space around the furnace.

Failure to follow this warning could result in property damage,

personal injury or death.

EXPLOSION HAZARD

Should overheating occur, or the gas supply fail to shut off, shut

off the manual gas valve to the furnace before shutting off the

electrical supply.

Failure to follow this warning could result in property damage,

personal injury or death.

If the furnace is shut down during the cold weather months,

provisions must be taken to prevent freeze-up of all water

pipes and water receptacles.

Do NOT touch igniter. It is extremely hot.

The furnace area must be kept clear and free of combustible

materials, gasoline, and other ﬂammable vapors and liquids.

Insulating materials may be combustible. The furnace must be

kept free and clear from insulating material. Examine the area

around the furnace for insulation after installation or when

insulation is added.

The combustion air for your furnace must be fresh

uncontaminated air. Paints, varnishes, laundry bleaches,

detergents, many household cleaners, water softening salts,

adhesives, and all such products release fumes containing

compounds which could lead to early heat exchanger and vent

system deterioration. Do not store these types of products near

your furnace.

For horizontally vented furnaces, the vent and inlet terminals

must be located at least 12 inches minimum (18 inches in

Canada) above normally expected snow accumulation level.

7 32-5064-WEB01

Proper Maintenance – Gas Furnaces

Air Filters

Clean the filter once a month for optimum performance. A

monthly visual inspection of the furnace is also recommended.

See General Inspection on page 9, number 1.

NOTE: Filters are NOT included with all Furnaces, however; the

Furnace should never be run without a ﬁlter.

A clean ﬁlter saves money.

When the furnace circulates and ﬁlters the air in your home, dust

and dirt particles build up on the ﬁlter. Excessive accumulation

can block the airﬂow, forcing the unit to work harder to maintain

desired temperatures.

And the harder your unit has to work, the more energy it

uses. So you pay more any time your system is running with

a dirty ﬁlter.

Help ensure top efﬁciency by cleaning the ﬁlter once a month.

Clean it twice a month during seasons when the unit runs

more often.

You can clean the filter with a

vacuum, OR you can wash it with

a household detergent.

NOTE: Not all aftermarket ﬁlters

can be washed with a household

detergent. See the instructions

supplied by the aftermarket ﬁlter

manufacturer.

When replacing your furnace ﬁlters, always use a high velocity

type which are the same size as originally supplied. Filters are

available from your dealer.

Where disposable ﬁlters are used, they must be a high velocity

type which are the same size as originally supplied.

How to remove the ﬁlter from your Gas Furnace.

Never operate your unit for either heating or cooling with

ﬁlters removed.

Upﬂow furnaces use a high velocity type air ﬁlter which may

be located within the furnace blower compartment in either a

BOTTOM or SIDE (left or right) return air inlet. The ﬁlter may be

secured with ﬁlter retaining brackets (as shown) or a ﬁlter rack.

To clean or replace ﬁlters, remove blower access door, slide the

filter from the filter rack or remove the filter from the retaining

brackets. After cleaning, replace the filter in the same manner,

making sure that the ﬁlter is secured in place in both the front and

back ﬁlter retaining brackets, if present, or that the ﬁlter is securely

For vertical UPFLOW ONLY, a left

or right return air inlet as above

(left side shown) requires

trimming of the factory supplied

ﬁlter to 17" x 25" x 1" for both the

21" and 24-1/2" wide furnaces.

Air filters may also be located

outside of the furnace using a side

ﬁlter frame.

Upﬂow/Horizontal Furnace Filters

The Upflow/Horizontal furnace when installed horizontally

requires a horizontal ﬁlter kit. The ﬁlters may be located remote

to the furnace or in the return air duct near the furnace. Check

with your dealer for the location of your ﬁlters.

An upflow/horizontal furnace in horizontal return air filter

application, as shown, features two 16" x 20" x 1" ﬁlters in the

17-1/2", 21" and 24-1/2" wide furnace cabinets.

To replace ﬁlters, remove the ﬁlter access door, lift the ﬁlter

from the lower bracket and shift the ﬁlter to the side to free the

top ﬁlter from the bracket and slide the ﬁlters out through the

ﬁlter access door. After cleaning, replace the ﬁlters in the same

manner making sure that the ﬁlters are secured in place in both

top and bottom ﬁlter brackets. Replace ﬁlter access door.

ELECTRIC SHOCK HAZARD

Disconnect power to unit before removing blower door. Failure

to follow this warning could result in property damage, personal

injury or death.

Upﬂow Bottom Return

Airow

Upﬂow Side Return

Airow

Upﬂow Only

Your ﬁlter may

or may not be

framed.

slid all the way into the ﬁlter rack. Replace blower access door. A

bottom return air inlet as shown features a 17" x 25" x 1" ﬁlter in

the 17-1/2" wide furnace; cabinets; a 20" x 25" x 1" ﬁlter in the 21"

wide models; and a 24" x 25" x 1" ﬁlter in the 24-1/2" wide cabinet.

Upﬂow/Horizontal

With Filter Kit

Airﬂow

8 32-5064-WEB01

Proper Maintenance – Gas Furnaces

Air filters may also be located

outside of the furnace using a

remote ﬁlter grille. The ﬁlter grille

could be in a hallway, wall, or in the

ceiling. Check with your dealer for

the exact location of your ﬁlter and

the method of changing the ﬁlters.

Downﬂow/Horizontal furnaces are

factory supplied with 2 standard

size permanent type air filters

which may be located remote

to the furnace or in the return air

duct. Check with your dealer for the

location of your ﬁlters.

A downﬂow/horizontal furnace return air ﬁlter application, as

shown, features two 14" x 20" x 1" ﬁlters in the 17-1/2" wide

furnace cabinets; or two 16" x 20" x 1" ﬁlters in the 21" and

24-1/2" wide furnace cabinets.

For regular dealer maintenance please refer to

www.acca.org/industry/quality

Airﬂow

Downﬂow/Horizontal

With Filter Kit

Before you call for service, check the following:

Problem Possible cause Possible Remedy

No heating –

Blower does not operate

1. Thermostat set incorrectly

2. Blown fuse or tripped circuit breaker

3. Defective component

4. Burner does not ignite

5. Main gas line turned off

6. Blower door removed or ajar

7. Lockout

1. Adjust thermostat. See operating instructions.

2. Replace or reset protective device or call for servicer

3. Most controls are automatic and will recycle. If your unit

still does not operate call for servicer.

4. Call servicer

5. Have gas company check

6. Close door securely to restore power to blower

and gas valve

7. Turn power on‑off‑on‑off twice in 30 seconds

Insufﬁcient heating or cooling 1. Dirty ﬁlters

2. Air not circulating freely

3. Blocked outdoor coil

1. Clean or replace

2. Check supply registers and return grills for blockage

3. Clear away leaves or other debris

No Heat – Vent motor is running 1. Restricted or plugged furnace

condensate drain

1. Remove drain clamps to condensate trap

and drain pan outlet

2. Flush or clean drain blockage

3. Reinstall clamps

Unusual Noise Call your local servicer

The Problem Solver – Gas Furnaces

NOTE: Improperly sized vents can cause the formation of

condensate, combustion gas leakage and spillage, and an

inoperable furnace.

A furnace is not a household appliance. It is complex and

requires professional maintenance and repair. Attempts at

“do-it-yourself” repairs on an in-warranty unit may void the

remainder of your warranty.

Other than performing the simple maintenance recommended

in this manual, you should not attempt to make any adjustments

to your furnace. Your dealer will be able to take care of any

questions or problems you may have. A periodic inspection of

your furnace should be made by a qualiﬁed service agency at

the start of each heating season.

In the event that electrical, fuel, or mechanical failures occur,

immediately turn the gas supply off at the manual gas valve located

on the gas pipe leading to the furnace before turning off electrical

power to the furnace. Contact a qualiﬁed service agency.

Keep your furnace looking like new for years.

Clean the enamel ﬁnish of your furnace with ordinary soap and

water. For stubborn grease spots, use a household detergent.

Lacquer thinner or other synthetic solvents may damage the ﬁnish.

CARBON MONOXIDE POISONING HAZARD

DO not attempt to change the venting system. Failure to

follow the installation and operation instructions for the

venting system’s operation could result in carbon monoxide

poisoning or death.

Downﬂow Filter

Airﬂow

9 32-5064-WEB01

 1. GENERALINSPECTION–Examinethefurnaceinstallation

forthefollowingitems:

a. Allueproductcarryingareasexternaltothefurnace

(i.e. chimney, vent connector) are clear and free of

obstruction.

b. The vent connector is in place, slopes upward and is

physicallysoundwithoutholesorexcessivecorrosion.

c. The return air duct connection(s) is physically sound, is

sealed to the furnace and terminates outside the space

containing the furnace.

d. The physical support of the furnace should be sound

without sagging, cracks, gaps, etc., around the base so

as to provide a seal between the support and the base.

e. There are no obvious signs of deterioration of the

furnace.

f. The burner ﬂames are in good adjustment without

erratic ﬂames. See illustration below.

g. Fresh air inlet and vent are not blocked and free from

obstruction. The horizontal or vertical vent and inlet

must be located at least 12 inches minimum (18 inches

inCanada)abovethenormallyexpectedsnow

accumulation level.

Contact your service agent if you feel you are uncomfortable

performing any of the inspections noted in section 1.

 2. BLOWERS–Theblowersizeandspeeddetermine

the air volume delivered by the furnace. The blower

motor bearings are factory lubricated and under normal

operating conditions usually do not require servicing.

Annualcleaningoftheblowerwheelandhousingis

recommendedformaximumairoutput,andthismustbe

performed only by a qualiﬁed servicer or service agency.

 3. IGNITER–Thisunithasaspecialhotsurfacedirectignition

devicethatautomaticallylightstheburners.Pleasenote

that it is very fragile and should be handled with care.

For regular dealer maintenance please refer to

www.acca.org/industry/quality

To ensure proper operation of your furnace, the

recommended dealer inspection is once a year, before the

heating season. Regular maintenance must be performed by

a qualiﬁed service professional.

The servicer should perform steps 1–9 once a year before

the heating season.

The homeowner should perform the visual inspection in step

1 monthly when cleaning the furnace ﬁlter.

Unless it is an emergency, never stop the heating system by

shutting off the main power.

If the main power to your air conditioner is ever disconnected

for more than three hours, turn off the thermostat. Then wait

for at least three more hours after the power has been restored

before turning the thermostat back on. Failure to follow this

procedure could result in damage to your furnace.

Regular Dealer Maintenance

ThefollowingwarningcomplieswithStateofCalifornialaw,Proposition65.

HAZARDOUS GASES

Exposure to fuel substances or by-products of incomplete

fuel combustion is believed by the state of California to cause

cancer, birth defects, or other reproductive harm.

HAZARDOUS GASES

Unit is equipped with a blower door switch which cuts power

to blower and gas valve causing shutdown when door is

removed. Unit must not be altered to allow operation with the

blower door removed. Operation with doors removed or ajar

can permit the escape of dangerous fumes. All panels must be

securely closed at all times for safe operation of the furnace.

Failure to follow this warning could result in property damage,

personal injury or death.

EXPLOSION HAZARD

In the event that electrical, fuel or mechanical failures occur,

SHUT off the gas supply at the manual gas SHUT OFF valve,

located ON THE SUPPLY GAS PIPING COMING INTO THE

FURNACE, BEFORE TURNING OFF THE electrical power to the

furnace. contact servicer.

Failure to follow this warning could result in property damage,

personal injury or death.

Do NOT touch igniter. It is extremely hot.

EXPLOSION HAZARD

Should overheating occur, or the gas supply fail to shut off, shut

off the manual gas valve to the furnace before shutting off the

electrical supply.

Failure to follow this warning could result in property damage,

personal injury or death.

FLAME

10 32-5064-WEB01

 6. CIRCUITPROTECTION–Ifblowerorgasvalvefailto

operate, the cause could be the circuit breaker or a loose

or blown fuse. Replace fuse or reset circuit breaker.

 7. OPERATION–Yourwarmairfurnaceshouldnotbe

operatedinacorrosiveatmosphere.Paintsolvents,

cleaning chemicals, spray propellants, and bleaches

should not be used in the vicinity of the furnace during

normal operation.

 8. CONDENSATEDRAINS–Ifyouhaveacoolingcoilinstalled

with your furnace, condensate drains should be checked

and cleaned periodically to assure that condensate can

drain freely from coil to drain. If condensate cannot drain

freely water damage could occur. Furnace drain should also

be checked and cleaned at the start of each heating season.

 9. AIRCIRCULATION–Toensureincreasedcomfort,the

blower on this unit may be operated continuously for both

heating and cooling. This will result in constantly ﬁltered air

and aid in maintaining more even temperatures by avoiding

temperature stratiﬁcation throughout the conditioned area.

To accomplish constant air circulation, set your comfort

controlfanselectorto“ON.”Continuousfanmodeduring

COOLINGoperationmaynotbeappropriateinhumid

climates.Iftheindoorairexceeds60%relativehumidityor

simply feels uncomfortably humid, it is recommended that

thefanonlybeusedinthe“AUTO”mode.

 4. BURNER–Gasburnersdonotnormallyrequirescheduled

servicing, however, accumulation of foreign material

may cause a yellowing ﬂame or delayed ignition. Either

condition indicates that a service call is required. For

best operation, burners must be cleaned annually using

brushes and vacuum cleaner.

Turn off gas and electric power supply. To clean burners, remove

top burner bracket and lift burner from oriﬁce.

NOTE: Be careful not to break igniter when removing burners.

Clean burners with brush and/ or vacuum cleaner. Reassemble

parts by reversal of the above procedure.

NOTE: On LP (propane) units, some light yellow tipping of the

outer mantle is normal. Inner mantle should be bright blue.

Natural gas units should not have any yellow tipped ﬂames.

This condition indicates that a service call is required. For best

operation, burners must be cleaned annually using brushes and

vacuum cleaner.

NOTE: On LP (propane) units, due to variations in BTU content

and altitude, servicing may be required at shorter intervals.

 5. HEATEXCHANGER/FLUEPIPE–Theseitemsmustbe

inspected for signs of corrosion, and/ or deterioration

at the beginning of each heating season by a qualiﬁed

service technician and cleaned annually for best

operation.

Regular Dealer Maintenance