Trango Systems PTZ900TX Wireless camera control system User Manual

Download:
Mirror Download [FCC.gov]
Document ID	17425
Application ID	QK3c7AIpWt0XvCPdh00pLA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.39kB (42424 bits)
Date Submitted	1998-12-23 00:00:00
Date Available	2000-12-14 00:00:00
Creation Date	2001-07-10 08:51:56
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-07-10 08:51:57
Document Title	user manual

PTZ-900 Series
______________________________________________________________________________________
900 MHz Spread Spectrum
Digital Wireless Pan/Tilt/Zoom Camera Control Transmission System
Installation and Operating Instructions
Your Trango Systems Wireless PTZ System:
Congratulations on choosing Trango Systems, Inc. to fulfill your wireless needs. Unpack your system carefully. If any items are
missing, notify your sales representative. If an item appears to be damaged from shipment, replace it in its packing material and notify
the shipper.
Save the packaging for further storage of the equipment.
Service:
If the unit ever needs repair service, contact Trango Systems customer service for return authorization and shipping instructions.
Note: This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance
with these instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by
one of more of the following meaures:
1) Reorient the receiving antenna;
2) Increase the separation between the affected equipment and the receiver;
3) Connect the affected equipment to an outlet on a different circuit from that
which the receiver is connected to;
4) Consult the dealer and/or experienced radio/TV technician for help.
FCC ID Numbers:
Transmitter PTZ-900TX:
FCC ID# NCYPTZ900TX
WARNING: Intentional or unintentional changes or modifications not expressly approved by the party responsible for
compliance must not be made. Any such modifications could void the user’s authority to operate the equipment.
QUICK START GUIDE
1.
VERIFY PROPER OPERATION OF CAMERA CONTROL USING A DIRECT WIRED
CONNECTION PRIOR TO INSTALLING WIRELESS LINK.
2.
SET THE PTZ-900TX AND PTZ-900RX SERIAL PORT DATA RATE AND MODE (RS422 or
RS232) USING THE TRANGOLINK PROGRAM AND SUPPLIED CABLE. (THIS STEP NOT
REQUIRED IF THE PTZ CONTROL EQUIPMENT IS SET TO USE 9600 BPS and RS422 or
RS485 MODE)
3.
INSTALL TRANSMITTER AND RECEIVER UNITS IN DESIRED LOCATION TO 2 3/8”
MAX DIAMETER STEEL POLE PER INSTALLATION DRAWING.
4.
INSTALL ANTENNAS ABOVE THE ENCLOSURES AND ALIGN PROPERLY.
IMPORTANT NOTE: THE PTZ-900TX (TRANSMITTER) USES A SPECIAL ANTENNA
CONNECTOR. ONLY USE ANTENNAS SUPPLIED BY TRANGO SYSTEMS WITH THIS TYPE
OF CONNECTOR OR DAMAGE TO THE UNIT MAY OCCUR.
5.
TIGHTEN ANTENNA CABLE TO RECEIVER AND TRANSMITTER. APPLY A SMALL
AMOUNT OF SILICONE TO FLANGE TO MAKE A LEAKPROOF CONNECTION.
6.
CONNECT INTERFACE AND POWER CABLES TO UNITS THROUGH FLANGES.
TIGHTEN FLANGES TO ALLOW SMALL AIR GAP AT BOTTOM OF ENCLOSURE.
MAKE SURE THAT GROUNDING STRAP IS SECURE TO AN EARTH GROUND.
7.
VERIFY THAT LEDs ARE SOLID RED ON TRANSMITTER AND RECEIVER BEFORE
SENDING PTZ COMMANDS.
8.
TIGHTEN LID OF ENCLOSURE DOWN.
IMPORTANT NOTE: DO NOT APPLY POWER TO THE TRANSMITTER UNLESS THE
ANTENNA IS CONNECTED. PERMANENT DAMAGE MAY RESULT.
SAFETY NOTE: THE PTZ-900TX TRANSMITTER OUTPUT POWER VARYS BETWEEN ½
and 4 WATTS EIRP. ALTHOUGH TRANSMISSIONS ARE OF A SHORT DURATION, IT IS
RECOMMENDED THAT THE TRANSMIT ANTENNA BE KEPT AT LEAST 3 FEET AWAY
FROM NEARBY PERSONS.
System Description:
The PTZ-900 is a professional quality wireless transmission system designed for sending simplex digital pan, tilt, zoom and camera
control signals up to 12 miles line-of-sight. The system employs 900 MHz frequency hopping spread spectrum technology with the
maximum effective output power allowed by the FCC for unlicensed operation. The system will operate interference free with the
Trango Falcon or Eagle series wireless video transmission systems to form a complete wireless control link.
Figure 1 shows the most common connection diagram for setting up a PTZ link using the PTZ-900 system.
Figure 2 shows the orientation of the antennas and mounting of the enclosures. Since the antennas are directional, they must be
aligned towards each other as shown. Optional antennas are available for omnidirectional coverage and increased transmission range.
NOTE: Make sure that you have tested the controller and receiver/driver using a direct connection (with wires) before installing the
wireless link.
Installation:
The system is factory-configured for operation at 9600 BPS, RS-422 mode, hopping sequence 1. If your controller and
receiver/driver operate at a different speed or use RS-232 protocol, you must reprogram the PTZ-900TX and PTZ-900RX using the
supplied cable and the Trangolink software which runs on any Windows 95 or higher computer. See “Changing System parameters”
section for detailed information.
To obtain the best performance and transmission distance, the following rules of thumb should be followed:
1) Mount the transmitter and receiver antennas above human and mechanical traffic. The higher the better.
2) Keep the transmission path as open as possible. Objects such as walls and metallic objects near the transmission path will
reduce the transmission distance.
3) Do not add additional lengths of cable to connect the receiver to the antenna as significant losses in signal, and reduced
transmission range will occur.
The transmitter and receiver units come pre- mounted in a NEMA 4X rated polycarbonate enclosure which allows mounting of the
unit outdoors.
IMPORTANT NOTE: The supplied enclosure mounting brackets are designed for a 2 3/8” max
diameter, ¼” wall thickness steel pole. The pole must be securely mounted into the ground or to a
structure to prevent movement of the antenna and camera in windy conditions. This pole also acts as
an earth ground. The equipment is grounded through a grounding strap.
IMPORTANT NOTE: The Transmitter and Receiver units may get warm to the touch. This is
normal and does not affect operation in any way.
Page 3: Fig 1, Fig 2
TRANSMITTER OPERATION
Figure 3 shows the front panel of the PTZ-900TX transmitter and the functions of each input/output. Each is described in greater
detail below.
IMPORTANT NOTE: The transmitter uses a non-standard jack to connect to the
transmitter antenna. Any modification to this jack may void the user’s authority to operate
the equipment and will void the manufacturer’s warranty.
WARNING:
DO NOT APPLY POWER TO THE TRANSMITTER WITHOUT THE ANTENNA
SECURELY ATTACHED. DAMAGE TO THE UNIT MAY RESULT.
DATA INTERFACE -- This input accepts serial commands from any PTZ controller , and acts as an interface with the
Trangolink software to control it’s internal settings. See the Trangolink software program help for more information. This interface
acts as the input for simplex data up to 19200 bps.
POWER INPUT -- -- Accepts a 6-13 Volt DC power source. It is highly recommended that the supplied power adapters ( 7
VDC) be used to reduce heat from the unit. If another power adapter is to be used, ensure that it is well regulated (+/- 5%). Batteries
may be used as external power sources as well. The nominal current draw is 200 milliamperes when not sending commands and 520
mA while sending commands.
LED – The LED has three functional modes as follows:
1) Alternating Green/Red: The unit is waiting for a command from Trangolink (30 seconds after
startup only.)
2) Red- Unit is ready to receive data from the PTZ control equipment.
3) Green – The unit is sending data on the air. Since the data is typically sent out in bursts, the
LED will be green for a very short time only.
RECEIVER OPERATION
Figure 4 shows the front panel of the PTZ-900RX receiver and the functions of each input/output. Each is described in greater detail
below.
DATA INTERFACE -- This output sends serial commands received from the transmitter out to the PTZ receiver/driver , as
well as interfacing with the Trangolink software to control it’s internal settings. See the Trangolink software program help for more
information. This interface acts as the output for simplex data up to 19200 bps.
POWER INPUT -- -- Accepts a 6-13 Volt DC power source. It is highly recommended that the supplied power adapters ( 7
VDC) be used to reduce heat from the unit. If another power adapter is to be used, ensure that it is well regulated (+/- 5%). Batteries
may be used as external power sources as well. The nominal current draw is 200 milliamperes.
LED – The LED has three functional modes as follows:
1)
2)
3)
Alternating Green/Red: The unit is waiting for a command from Trangolink (30 seconds after
startup only.
Red- Unit is ready to receive data from the PTZ-900TX transmitter.
Green – Not used.
CONNECTOR WIRING
Supplied with the units are DB9- female to R-45 adapters that can be used to wire the units properly. Below are common wiring
diagrams for various manufacturer’s PTZ equipment and a description of the individual pins on the Transmitter and receiver.
Diagrams
POINT TO MULTIPOINT OPERATION
In some cases it may be necessary to control more than one camera from the same control panel. In this case, one PTZ-900TX
transmitter would send control signals to all receivers, and the receiver drivers will filter the data as in a hardwired system. The user
must ensure that all receivers have the same address and PN sequence selected.
MULTI-LINK OPERATION
Different from Point to Mutipoint operation, this is where more than one transmitter is operating in the same area. In this case, all the
transmitters and receivers operating on System “A” would have the same PN code and address. Those on system “B” should have a
different address
TRANGOLINK SOFTWARE OPERATION
The Trangolink software allows the user to change the user settings on the PTZ-900TX and PTZ-900RX.
The software runs under the Windows 95 PC platform and connects from either COM1 or COM2 to the
Data interface on the transmitter or receiver via the Cabldat-2 interface cable. After entering the program, a
screen is displayed showing the current settings. The user may change the settings and upon exiting the
program and cycling power to the unit the settings will be come effective.
PN Sequence: The hopping channel sequence, which must be the same on the transmitter and receiver in
order for data to be transferred properly.
RSSI: Used for receiver only to monitor the radio spectrum on all hopping channels. Useful in
troubleshooting to determine if any signals are present in the 900 MHz band.
Data Rate: Serial port data rate for user data. Must be the same on the transmitter and receiver.
Trangolink interface is unaffected by changes made here.
Mode: RS-232 (unbalanced) or RS-422/RS-485 (differential). Select the mode which matches your PTZ
control equipment.
Address: Used if more than one system is to be used on the same hopping sequence in the same area.
TROUBLESHOOTING
INTERFERENCE – INTERMITTENT OPERATION
Heavy equipment such as industrial roof –mounted air conditioners or fan motors in close proximity to the transmitter or receiver or
cables may cause interference, especially when operating using RS232 mode. Move the unit/cable away from the source of the
interference.
Antenna polarization may be wrong. The AD900-9 antenna is normally horizontally polarized which has been determined to give the
best results. When using Yagi antenna on the receiver make sure that the alignment is as follows:
pic
Raise transmitter and receiver antennae above ground and away from obstacles and traffic, including foot traffic.
Verify all connectors are tight.
Shorten the receiver antenna feed cable.
Cable from transmitter to PTZ controller is too long, corrupting digital data. Use Cat 5 twisted pair shielded cable if possible with a
maximum length of 500 feet for RS422 and 200 feet for RS232.
If the system becomes unusable for a period of time on the order or minutes or hours and then becomes usable again, changing the PN
sequence may cure the problem. The different PN sequences have different waiting channels that are used to synchronize the hopping
sequences. Depending on your environment, there may be a 900 MHz transmitter interfering on one of the waiting channels. By
changing the PN sequence on the transmitter and receiver, the waiting channel will change. Some of the types of equipment that may
interfere are: 900 MHz cordless phones, wireless LANs if very close to the PTZ-900RX receiver.
High power equipment operating near the 902-928 MHz band such as paging system base stations or cellular phone base stations may
also interfere if they are within several hundred feet of the receiver. Changing the PN sequence and reorienting the receive antenna
will most like cure this type of interference.
Cable from receiver to PTZ receiver/driver is too long, corrupting digital data. Use Cat 5 twisted pair shielded cable if possible with a
maximum length of 500 feet for RS422 and 200 feet for RS232.
NO DATA IS RECEIVED
Check that the transmit and receive PN sequences, data rate, mode and address are set the same.
Verify all connectors are tight.
Verify that transmitter and receiver antennas are aligned properly as discussed above.
CAN’T COMMUNICATE WITH TRANSMITTER OR RECEIVER USING TRANGOLINK
Plug in the supplied cable to the unit. Power the computer on. Power the transmitter or receiver on, and within 30 seconds run the
Trangolink program from Windows. The LED will alternate between greed and red to indicate that it is ready to Talk to the
Trangolink software. Use the supplied cable or any standard null modem RS232 cable.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:07:10 08:51:56
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:07:10 08:51:57-04:00
Page Count                      : 10

EXIF Metadata provided by EXIF.tools