Trango Systems VTX5950 5.8GHz Wireless Video/Audio/Alarm/Data Transmitter User Manual B

Download:
Mirror Download [FCC.gov]
Document ID	230343
Application ID	NsvBsNRj8kGjrwh5aeUBmg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.82kB (822771 bits)
Date Submitted	2002-03-11 00:00:00
Date Available	2002-03-11 00:00:00
Creation Date	2002-02-07 11:25:48
Producing Software	Acrobat PDFWriter 4.05 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	B.PDF
Document Creator	Microsoft Word
Document Author:	dteng

Falcon PLUS™ SERIES
5.8 GHz Wireless Video/Audio/Alarm/Data
Transmission System
Installation and Operating
Instructions
(This Page Intentionally Left Blank)
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
Quick Start Guide
1• Verify proper operation of camera and monitor/event
recorder using coaxial cable prior to installing wireless link.
2• Install transmitter (VTX5900) and receiver (VRX5900) units
to a steel pole in desired location per installation drawing
(see Figure 1A). The pole must be securely mounted so that
it does not move, and may be from 1.5” to 3” in diameter.
3• Install antennas above the enclosures.
WARNING
USE EXTREME CARE WHEN INSTALLING ANTENNAS
NEAR POWER LINES.
4• Slide heatshrink over antenna cable. Tighten antenna cable
to receiver and transmitter. Heat the heatshrink until it
contracts around the connector junction.
5• Connect video, audio, power, alarm, PC interface cables as
needed to units through flanges. Tighten flanges to allow
small air gap at bottom of enclosure.
IMPORTANT NOTE:
Power adapter must be kept dry.
6• Verify that LEDs are lit up and transmitter and receiver are
on same channel.
7• Tighten lid of enclosure.
8• To help protect against potential lightning damage, use a
lightning surge arrestor in line with all cabling entering a
structure and at the antenna input.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
CAUTION
DO NOT APPLY POWER TO THE TRANSMITTER UNLESS
THE ANTENNA IS CONNECTED. PERMANENT DAMAGE
MAY RESULT.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
Your Trango Wireless Video System
Congratulations on choosing Trango Systems, Inc. to fulfill your
wireless video needs. Unpack your system carefully. If any items
are missing, notify your sales representative. If an item appears to
be damaged from shipment, replace it in its packing material and
notify the shipper.
Save the packaging for further storage of the equipment.
Service:
If the unit ever needs repair service, contact a Trango
Systems, Inc. distributor for return authorization and
shipping instructions.
FCC Information:
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in
accordance with these instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to correct the interference by one of more of the following
measures:
1) Reorient the receiving antenna;
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
2) Increase the separation between the affected
equipment and the receiver;
3) Connect the affected equipment to an outlet on a
different circuit from that
which the receiver is connected to;
4) Consult the dealer and/or experienced radio/TV
technician for help.
VTX5950: #NCYVTX5950
VTX5900: # NCYVTX5900
CANADA: VTX5900: 29451031885
VRX5900: 29451031885A
IMPORTANT NOTE:
Intentional or unintentional changes or modifications not
expressly approved by the party responsible for
compliance must not be made. Any such modifications
could void the user’s authority to operate the equipment
and will void the manufacturer’s warranty.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
System Description:
The Falcon PLUS™ Wireless Video System is a
professional quality system designed for sending composite
NTSC or PAL video, audio, and alarm signals using 5.8 GHz
wireless technology. The typical Falcon PLUS™ system
consists of a VTX5900 transmitter and antenna, VRX5900
Receiver and antenna, and power adapters. The system is
ideal for permanent or temporary video links due to its
portable nature and easy installation. It is not designed for
operation while in motion.
Figure 1a shows the most common connection diagram for
setting up a wireless video link using the Falcon PLUS™.
Audio connections are not shown. The default channel
selection is Channel 1.
Figures 1b, 1c, and 1d show the orientation of the antennas
and mounting of the enclosures.
NOTE: Make sure that your camera and monitor/recorder
work properly hardwired before attempting to install the
wireless link.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
• Figure 1a•
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
• FIGURE 1b •
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
• FIGURE 1c •
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
• FIGURE 1d •
10 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
Installation:
The Falcon PLUS™ system is factory-configured for
operation on channel 1 with right and left audio operational.
To obtain the best picture quality and transmission distance,
the following rules of thumb should be followed:
1) Mount the transmitter and receiver antennas above
human and mechanical traffic, the higher the better. A
10 foot 2 3/8” diameter steel mast on top of a building is
typical. Make sure that the mast is well grounded to
earth ground with an 8 AWG or larger wire. For
maximum range, the transmit and receive antennas
must be 15 to 20 feet above all obstacles in the line of
sight.
2) Keep the transmission path as open as possible.
Objects such as walls and metallic objects near the
transmission path reflect signals and may reduce the
transmission distance.
3) Do not add additional lengths of cable to connect the
receiver to the antenna as significant losses in signal
and reduced transmission range will occur.
4) Keep the cable connecting the antenna to the
receiver as short as possible.
The VTX5900 transmitter and VRX5900 receiver units come
pre-mounted in a NEMA 4X rated aluminum enclosure that
allows mounting of the unit outdoors.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
11
Transmitter Operation
igure 2 shows the interior of the VTX5900 transmitter and the
functions of each control and input/output. Each control is
described in greater detail below. This card is encased in a NEMA
4X rated aluminum/powdercoat enclosure. Do not remove the card
from the enclosure.
IMPORTANT NOTE: The transmitter uses a nonstandard jack to connect to the transmitter antenna.
Any modification to this jack may void the user’s
authority to operate the equipment and will void the
manufacturer’s warranty.
CAUTION
DO NOT APPLY POWER TO THE TRANSMITTER
WITHOUT THE ANTENNA SECURELY ATTACHED.
DO NOT APPLY VOLTAGE TO THE ALARM PINS.
DAMAGE TO THE UNIT MAY RESULT.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Power
Alarm 1/2 inputs
Right audio input
Left audio input
Stereo/Alarm switch
Data
Video input
Toggle/Standby
Status LED
Channel LEDs
Antenna connector
Header for use with optional LC-485/422
(LC485/422 used to transmit simplex data for control.)
12 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
11
Use with dry
(no voltage)
contact closures
only.
10
12
• FIGURE 2•
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
13
VTX5900 Transmitter Inputs & Controls:
1. POWER INPUT
Accepts a 6-12 Vdc power source such as the standard
7 Vdc adapter (Trango part number PT07800-1), or an
optional battery. The nominal current draw is 200
milliamperes. If using an adapter from a third party, use
a well-regulated 300 mA minimum output supply. Do
not use the PT07800-1 to power a camera or video
distortion may occur.
2. ALARM INPUTS
These inputs are used to send alarm signals to the
receiver. They sense an open or closed state and reflect
that state to the receiver whenever it changes. The
alarm inputs operate independently of each other. The
transmitter is capable of sending either alarms or stereo
audio, selectable via the Stereo/Alarm switch. If you wish
to use the audio feature and alarm, you will send only
mono audio.
3/4. RIGHT & LEFT AUDIO INPUTS
Designed to mate to standard RCA connectors, each
input accepts 1 Vpp audio input and is terminated with
600Ω unbalanced configuration. It is designed to
interface to “lineout” audio sources. A preamplifier must
be used to connect a microphone to this input.
5. STEREO/ALARM SWITCH
When this switch is in the “R Audio On” position, stereo
audio transmission is enabled. This permits the
transmission of stereo audio with no data or alarms.
When it is in the “Alm/Data Mode On” position, R audio
is disabled. In its place, either alarms or user data (Data
Pass-Through mode) are transmitted. Trango Systems’
MIC-001 can be used for audio transmission.
14 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
6. DATA INTERFACE
When connected to a personal computer via the optional
CBLDAT-1 interface cable, this input accepts serial
commands that control settings in the transmitters not
available on the front panel. See the TrangoLink
software section and program help for more information.
This is also the input for the RS-232 user data to be sent
in Data Pass-Through mode.
7. VIDEO INPUT
Designed to mate to a standard BNC male connector,
this input accepts 1Vpp video in both NTSC and PAL
formats. This input is terminated with 75Ω. RCA-BNC
adapters are available for use with some cameras and
VCRs.
8. TOGGLE/STANDBY
Depressing this switch momentarily changes the
transmitter channel. Remember to change the receiver
channel as well, since it is not automatically changed
when the transmitter channel is changed. Holding the
button down for 2 seconds places the transmitter in
Standby Mode.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
15
9/10. STATUS/CHANNEL LEDs
These LEDs display the transmitter status and current
transmitter channel. There are 12 channels to choose
from.
CAUTION
DO NOT APPLY EXTERNAL VOLTAGES TO THE
ALARM INPUTS AS PERMANENT DAMAGE TO THE
UNIT MAY RESULT. USE ONLY DRY CONTACTS
WITH THESE INPUTS.
16 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
VTX5900 Transmitter Operation:
Changing Channels:
To change channels, simply depress the Toggle/Standby
switch momentarily until the LED(s) for the desired
channel is lit up. Remember to change the receiver
channel as well, since it is not automatically changed
when the transmitter channel is changed. As a rule of
thumb, the first 6 systems operating along the same
transmission path should be set to use even channels
(2,4,6,8,10,12). If more than 6 systems are required
along the same transmission path, use opposite
polarization antennas and then set the units to operate
on the odd channels (1,3,5,7,9,11). Contact Trango
Tech Support for additional help on setting the correct
configuration for your application.
Standby Mode -- Secure Standby Mode:
In this mode of operation the transmitter:
1. stops transmitting over the air completely by
shutting down the majority of its circuitry to save
power, and
2. waits to be returned to Normal mode by one of
the following:
• a change in either Alarm input,
• the Toggle/Standby switch, or
• the TrangoLink software.
To enter Secure Standby mode, press and hold the
Toggle/Standby switch for 2 seconds or use the
TrangoLink software (See the TrangoLink section of this
manual for more information).
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
17
The Status LED will blink for about 1 minute to allow the
operator to leave the area. During this time the alarms
will not be sent to the receiver. After 1 minute, the alarm
inputs will be active and the status LED will then blink
every 2-3 seconds to indicate that the unit is in Secure
Standby mode.
To exit Secure Standby mode, momentarily press the
Toggle/Standby switch or use the TrangoLink software.
After exiting Secure Standby mode, the active channel
LEDs will be lit to indicate the transmitter is now
continuously transmitting again.
Standby Mode -- Power Save Standby Mode:
In Power Save Standby mode, the transmitter will awaken
(enter Normal mode) for a user-selectable amount of time if
an alarm is received over the Alarm 1 input. After this time
has expired, the transmitter will reenter Standby mode. The
amount of time after which the transmitter will reenter
Standby mode can be set to any value between 1 and 255
minutes using the TrangoLink software. If zero is entered,
the transmitter will be in Secure Standby mode, and will not
reenter Standby mode after awakening. More information
can be found in the TrangoLink section of this manual.
When the transmitter has been placed in Power Save
Standby mode, the Alarm 1 input is treated as normallyclosed. An open condition on this input will awaken the
transmitter for the preset amount of time. The state of the
Alarm 2 input does not affect the transmitter in Power Save
Standby mode.
18 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
In Power Save Standby mode the transmitter:
1. stops transmitting over the air by shutting down
the majority of its circuitry to save power,
2. periodically and momentarily powers up and
transmits over the air, and
3. waits to be returned to Normal mode by one of
the following:
• an open condition on the Alarm 1 input,
• the Toggle/Standby switch, or
• the TrangoLink software.
To exit Power Save Standby mode, momentarily press the
Toggle/Standby switch, or use the TrangoLink software.
After exiting Power Save Standby mode, the active channel
LED will be on solid to indicate that the transmitter is now
continuously transmitting again. If the Power Save Timer is
still enabled, the radio will go back to Power Save Standby
when it times out again.
Data Pass-Through Mode:
The transmitter and receiver can be used to pass data at
rates from 1200 to 9600 bps. (For optimum data
transmission without losses, both the transmitter and
receiver should be configured to pass or accept data at
the same rate. The data rate and parity are configured
using the TrangoLink software.) To enter Data PassThrough mode, the illustrated switch should be placed in
“Alm/Data Mode On.” Then, from the TrangoLink
software, select “Pass-Through Mode.” Make sure both
the VTX5900 and the VRX5900 have been configured
for Data Pass-Through mode.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
19
The Right Audio channel will be disabled in this mode
while the Left Audio channel can still transmit monaural
audio. Alarms and Link Verification cannot be
transmitted when in Data Pass-Through mode. Do not
use CBLDAT-1 to send or receive data since it contains
extra wires not used for normal data transmission.
Figure 3 displays the pinout diagram to connect to the
RJ11 Data connector for RS-232 data pass-through.
To pass simplex (one way) RS-485 or RS-422 format
serial data, use the LC485/422 available from your
dealer. If using the LC485/422 converter, the data
connector must not be connected to any cabling. (to
prevent data corruption or damage to equipment.)
PIN NUMBER
20 M-FALCON2 Rev B
DESCRIPTION
Reserved -- DO NOT USE
RS-232 Serial Data In to Radio
GND
Reserved -- DO NOT USE
RS-232 Serial Data Out to PC
Reserved -- DO NOT USE
• FIGURE 3 •
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
Low Battery:
If the input voltage drops below 6V, the status LED will
blink twice per second. A low battery indication is also
sent to the receiver and can be viewed using the
TrangoLink software or the receiver. No alarm is
generated.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
21
Receiver Operation
igure 4 shows the front panel of the VRX5900 receiver and the
functions of each control and input/output. This card is encased in
a NEMA 4X rated aluminum/powdercoat enclosure. Do not remove
the card from the enclosure.
1. Power
2. Alarm 1/2 relay outputs
3. Right audio output
4. Left Audio output
5. Stereo/Alarm switch
6. Data
7. Video output
8. Toggle/RSSI
9. Channel LEDs
10. Antenna connector
11. Header for use with optional LC485/422
(LC485/422 used to transmit simplex data for control.)
22 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
10
Use with dry
(no voltage)
contact closures
only.
11
• FIGURE 4 •
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
23
VRX5900 Receiver Inputs/Outputs & Controls:
1. POWER INPUT
Accepts a 6-9 Vdc power source such as the standard 7
Vdc adapter (Trango part number PT07800-1), or an
optional battery. The nominal current draw is 450
milliamperes. If using an adapter from a third party, use
a well-regulated 6-9Vdc/500mA output supply.
2. ALARM OUTPUTS
These are dry (no voltage) contact relay outputs that can
sink 1 ampere at 40 V AC/DC. When the corresponding
transmitter alarm input closes or opens, this output will
close and open as well. Consider these outputs mirrors
of the transmitter alarm inputs. These outputs are
independent and can be used to turn on peripheral
devices such as video recorders and audible alarms.
3/4. RIGHT & LEFT AUDIO OUTPUTS
Designed to mate to a standard RCA male connector,
this provides a 1.5 Volt peak-to-peak audio output and
should be terminated in a minimum 600Ω load, as is
found in most “line in” audio inputs.
5. STEREO/ALARM SWITCH
When this switch is in the “R Audio On” position, stereo
audio transmission is enabled. This permits the
transmission of stereo audio with no data or alarms.
When it is in the “Alm/Data Mode On” position, alarm
transmission is enabled. If Data Pass-Through mode is
enabled through the TrangoLink software, the switch
must be set to the “Alm/Data Mode On” position.
6. DATA INTERFACE
When connected to a personal computer via the optional
CBLDAT-1 interface cable, this input accepts serial
24 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
commands that control settings in the receiver not
available via the front panel. See the TrangoLink
software program help for more information. This port is
also used for Data Pass-Through mode for RS-232
signal levels.
7. VIDEO OUTPUT
Designed to mate to a standard BNC male connector,
this provides a 1 Volt peak-to-peak video signal output.
This must be terminated with 75Ω. RCA to BNC
adapters are available for use with some monitors and
VCR inputs.
8. TOGGLE/RSSI
To change the receiver channel, depress this switch
momentarily. Remember to change the transmitter
channel as well since it is not automatically changed.
To enter RSSI (Received Signal Strength Indicator)
mode, hold down this button for 2 seconds. The number
of channel LEDs lit is an indicator of signal strength,
which can aid in finding the best antenna position.
9. CHANNEL LEDs
These LEDs display the current receiver channel and act
as a Received Signal Strength Indicator.
CAUTION
DO NOT APPLY EXTERNAL VOLTAGES TO THE
ALARM OUTPUTS. PERMANENT DAMAGE TO THE
UNIT MAY RESULT.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
25
VRX5900 Receiver Operation:
Changing Channels:
To change channels, simply depress the Toggle/Standby
switch momentarily until the LED for the desired channel
pattern is lit up. Remember to change the transmitter
channel as well, since it is not automatically changed
when the receiver channel is changed. As a rule of
thumb, the first 6 systems operating along the same
transmission path should be set to use even channels
(2,4,6,8,10,12). If more than 6 systems are required
along the same path, use opposite polarization antennas
and then set the units to operate on the odd channels
(1,3,5,7,9,11). Contact Trango Tech Support for
additional help on setting the correct configuration for
your application.
Alarm Outputs:
When the VRX5900 receives an alarm state change
from the transmitter, it will close or open the
corresponding alarm output. The state of the alarm
outputs (open or closed) can be viewed using the
TrangoLink software. If the transmitter is in Standby
mode or the transmitted signal is lost, the receiver will
hold the last received valid state of the alarms. The
Alarm outputs are dry-contact relays.
RSSI Mode:
To ease alignment of the receiver antenna, the received
signal strength may be viewed by placing the unit in
RSSI mode. The LEDs will then act as a bar-graph
indicator, with more LEDs lit for a stronger signal.
26 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
To enter RSSI mode, hold down the Toggle/RSSI button
for 2 seconds. To exit, depress the button momentarily.
The number of LEDs lit is a relative indication of signal
strength to be used only to find the best antenna
position. Viewing the received picture quality should be
used in conjunction with this mode.
Data Pass-Through Mode:
The transmitter and receiver can be used to pass user
data one-way from the VTX5900 to the VRX5900 at
rates from 1200 to 9600 bps. (For optimum data
transmission without losses, both the transmitter and
receiver should be configured to pass or accept data at
the same rate. The data rate can be configured using
the TrangoLink software.) To enter Data Pass-Through
mode, the Stereo/Alarm switch should be placed in
“Alm/Data Mode On.” Then, from the TrangoLink
software, select “Pass-Through Mode.” Make sure both
the VTX5900 and the VRX5900 have been configured
for Data Pass-Through mode. The Right Audio channel
will be disabled in this mode while the Left Audio
channel can still transmit monaural audio. Alarms and
Link Verification cannot be transmitted when in Data
Pass-Through mode. Do not use CBLDAT-1 to send or
receive data since it contains extra wires not used for
normal data transmission.
Please see the pinout diagram in Figure 3 for more
information on wiring the data connector for RS-232.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
27
Troubleshooting the
Falcon PLUS™ System
INTERFERENCE
If interference such as lines in the pictures is observed,
changing the transmission channel may cure the
problem.
Also, AC generators in close proximity to the transmitter
or receiver may cause lines in the picture. Move the unit
away from the source of the interference.
NO PICTURE
Check that the transmit and receive channels are set the
same, and make sure the transmitter is not in Standby
mode (slow, blinking LED), or that the battery is not low
(fast, blinking LED).
Verify all connectors are tight.
POOR PICTURE QUALITY
Raise transmitter and receiver antennas above ground
and away from obstacles and traffic, including foot traffic.
Use an optional high-gain dish antenna on the receiver.
Verify all connectors are tight. Shorten the receiver
antenna feed cable.
VIDEO TOO DARK
Make sure that any monitors/peripheral equipment
connected to the video source are set to high impedance
termination since the VTX5900 has a built-in 75Ω
termination.
28 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
VIDEO TOO BRIGHT
Make sure that the receiver video output line is
terminated with 75Ω.
CAN’T COMMUNICATE WITH TRANSMITTER OR
RECEIVER USING TRANGOLINK
Perform a system reset by holding toggle switch down
while applying power. All memory locations will be
erased and the system will be reinitialized. All LEDs will
light up to indicate a successful reset. Release the
toggle switch.
Check the Technical Support section of our website at
http://www.trangosys.com/ for additional assistance.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
29
TrangoLink™ Software with the
Falcon PLUS™ System
PC Requirements & Installation:
In order to run TrangoLink, you will need Windows 95 or
higher, 400 kB of free disk space, and one free 9-pin serial
port.
To install:
The TrangoLink program that can be found at our
website at http://www.trangosys.com/ is a selfextracting and installing file. To install TrangoLink on
your PC, simply download the file and double-click
on it.
To uninstall:
1. Click on Start, then Settings, then Control
Panel.
2. Double click on Add/Remove Programs.
3. Select TrangoLink, and click Add/Remove.
TrangoLink with the Falcon PLUS™ System:
The TrangoLink software allows the user to change the user
settings on the Falcon PLUS™ transmitters and receivers.
The software runs under the Windows 95 or higher PC
platform and connects from COM1-4 to the Data interface
on the transmitter or receiver via the CBLDAT-1 interface
cable.
To enter the program, the user must apply power to the
connected unit and run the TrangoLink program by clicking
on the TrangoLink icon in Start/Programs.
30 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
After entering the program, a screen is displayed showing
the current settings, which can be changed by the user.
Configuring the Falcon PLUS™ Transmitter:
Via the TrangoLink interface panel for the VTX5900
transmitter, the user can configure the following settings:
MENU CONTROLS:
File: Choosing this pull-down menu brings up three
options:
Sound: This toggles the PC sound on and
off, so that the PC can beep (or not) if a
change in any of the indicators is received.
Select Port: This selects the serial port
through which the PC is connected to the
transmitter or receiver. The cable required to
connect may be purchased from your Trango
Systems sales representative.
Exit: Exits TrangoLink.
Link Verification: This option brings up a dialog box by
which the Link Verification Code can be set. This is a
32-bit code sent from the transmitter to the receiver to
verify that the signal is being received from the proper
location. The link verification codes on the transmitter
and receiver must match for reception of alarms or low
battery signals. If the codes do not match video will still
be received, but the user will be notified that it is not
coming from the proper location.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
31
Pass-Through Mode: Choosing this pull-down menu
brings up the following dialog box shown in Figure 5
through which the data rate and parity can be chosen.
To use this function, the Stereo/Alarm switch on the
transmitter and receiver must be set to “Alm/Data Mode
On.”
• FIGURE 5 •
Help: Choosing this pull-down menu brings up two
options:
Help Topics: This offers you an index of
online help topics.
About: This displays the copyright notice and
version number of your copy of TrangoLink.
32 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
SCREEN CONTROLS:
Current Channel: This must be the same on the
transmitter and receiver in order for video, alarms,
and/or data to be transmitted properly.
Select Mode: The Normal button places the transmitter
in Normal mode or awakens it from Standby mode. The
Standby button places the transmitter in either Secure
Standby or Power Save Standby, depending on the
value entered in the Power Save Timer field.
Power Save Timer: The Falcon PLUS™ can reenter
Standby mode after a preset amount of time has passed,
which can be entered in the Power Save Timer field
(Power Save Standby mode). If zero is entered, the
transmitter will not reenter Standby mode (Secure
Standby mode). To enter a new value, type the desired
number of minutes into the Power Save Standby field,
and press the “Set new value” button.
In Figure 6, the TrangoLink interface screen shows that
the transmitter is set to Channel 3, in Normal mode (not
Standby), with the Power Save timer set to 0 minutes
(Secure Standby). In this configuration, the transmitter
will not reenter Standby mode after awakening.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
33
• FIGURE 6 •
34 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
Configuring the Falcon PLUS™ Receiver:
Via the TrangoLink interface panel for the VRX5900
receiver, the user can configure the following settings:
MENU CONTROLS:
File: Choosing this pull-down menu brings up three
options:
Sound: This toggles the PC sound on and
off, so that the PC can beep (or not) if a
change in any of the indicators is received.
Select Port: This selects the serial port
through which the PC is connected to the
transmitter or receiver. The cable required to
connect may be purchased from your Trango
Systems sales representative.
Exit: Exits TrangoLink.
Link Verification: This option brings up a dialog box by
which the Link Verification Code can be set. This is a
32-bit code sent from the transmitter to the receiver to
verify that the signal is being received from the proper
location. The link verification codes on the transmitter
and receiver must match for reception of alarms or low
battery signals. If the codes do not match video will still
be received, but the user will be notified that it is not
coming from the proper location.
Pass-Through Mode: Choosing this pull-down menu
brings up the following dialog box shown in Figure 7
through which the data rate and parity can be chosen.
To use this function, the Stereo/Alarm switch on the
transmitter and receiver must be set to “Alm/Data Mode
On.”
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
35
• FIGURE 7 •
Help: Choosing this pull-down menu brings up two
options:
Help Topics: This offers you an index of
online help topics.
About: This displays the copyright notice and
version number of your copy of TrangoLink.
36 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
SCREEN CONTROLS:
Current Channel: This must be the same on the
transmitter and receiver in order for video, alarms,
and/or data to be transmitted properly.
Link Verification Error: Green indicates that the
receiver is receiving a matching Link Verification Code
from the transmitter. Red indicates that it is not.
Sync Loss: Green indicates that the receiver detects a
vertical sync pulse on the received video signal. Red
indicates that it does not, and hence that no video is
being transmitted.
Low Transmitter Battery: Red indicates that the
transmitter has a low power supply voltage (< 6 Vdc).
Green indicates that power supply voltage is within
acceptable limits.
Alarm 1 and Alarm 2: OPEN indicates that contacts are
open on the receiver, CLOSED that they are closed.
Signal Strength: Also called RSSI (Received Signal
Strength Indicator). Presents a bar graph proportional to
the received signal. Useful in troubleshooting to
determine if any other signals are present in the
frequency band and to help align antennas.
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
37
In Figure 8, the TrangoLink interface screen shows that
the receiver is set to Channel 3, both Alarms are open,
and a low battery condition exists on the transmitter.
• FIGURE 8 •
• FIGURE 8 •
38 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
Parametric Specifications
VTX5900 Transmitter: Electrical
RADIO SECTION:
Frequencies:
Channel 1:
Channel 2:
Channel 3:
Channel 4:
Channel 5:
Channel 6:
Channel 7:
Channel 8:
Channel 9:
Channel 10:
Channel 11:
Channel 12:
RF Output Power:
VIDEO SECTION:
Input Level:
5740 MHz
5750 MHz
5762 MHz
5772 MHz
5784 MHz
5794 MHz
5806 MHz
5816 MHz
5828 MHz
5838 MHz
5850 MHz
5860 MHz
Meets FCC Part 15.249 radiated field
strength of 50 mV/m at 3 meters with
CP helix antenna provided with unit.
1Vpp per NTSC/PAL standard
Input Impedance:
75Ω unbalanced
Modulation:
Wideband direct FM (for composite
signal)
Modulation Index:
1.0 at 8.0 MHz for composite A/V
signal (±8.0 MHz deviation)
Pre-emphasis:
CCIR Rec 405-1
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
39
AUDIO SECTION:
Input Level:
1 Vpp Nominal
Input Impedance:
600Ω
Bandwidth:
50 Hz – 15 kHz (3 dB)
Modulation:
Wideband FM
Subcarriers:
6.0 MHz (right) and 6.5 MHz
(left-monaural)
Modulation Index:
1.0 at 75 kHz for audio (±75 kHz
deviation)
Pre-emphasis:
75 µS
ALARM SECTION:
Input Level:
Normally open contact closure input
on both Alarm 1 and Alarm 2. The
current state of the input (open or
closed) is transmitted to the receiver
which reflects the transmitter alarm
input states. DO NOT APPLY VOLTAGES
TO THESE INPUTS AS DAMAGE TO THE
UNIT WILL OCCUR.
POWER SECTION:
Input Voltage:
7 Vdc nominal, 6-12 Vdc range
Current Consumption:200 mA typical in normal mode,
10 mA in Standby mode
Max. Ripple Input:
1 Vpp
Low Battery Sens.:
< 6 Vdc
40 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
VTX5900 Transmitter: Mechanical &
Environmental
GENERAL:
Material:
Cast aluminum NEMA 4X rated
outdoor enclosure
Finish:
Off-white powdercoat
Size:
4.65” W x 8.8”L x 2.475”H without
antenna
Weight:
2.65 lb
CONNECTORS & INDICATORS:
RF Output:
Custom connector is in compliance
with FCC rules part 15C, 15.203.
FCC Compliance:
The transmitter shall comply with FCC
Part 15.249, FCC Part 15 Subpart B,
Industry Canada Specifications (RSS
210 Issue 2)
PC Interface:
6 position, 4 conductor RJ11 female
right angle PCB mount
Video:
BNC female PCB mount
Audio:
Red RCA female PCB mount – R
Audio
White RCA female PCB mount – L
Audio (Mono)
Alarm/Power:
6 post terminal block (6-12 Vdc, GND,
ALARM 1,
ALARM 2)
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
41
CONNECTORS & INDICATORS: (continued)
Controls:
Channel switch: momentary, toggles
through modes/channels
Stereo/Alarm switch: DPDT switch
allows selection of data/alarms or right
audio on 6.0 MHz subcarrier
Indicators:
4 channel LEDs which display the
current channel, 1 Status LED which
blinks slowly in Standby mode and
rapidly when battery is low
ENVIRONMENTAL:
Operating Temp.:
-20 to 70 º C
Storage:
-40 to 85 º C
Humidity:
100% (enclosure)
Shock:
Sustain 3-axis drop from 5’
42 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
VRX5900 Receiver: Electrical
VIDEO SECTION:
Video 3dB BW:
5.8 MHz (Conforms with NTSC/PAL
standard)
Video Output S/N:
> 40 dB with –85 dBm RF input
> 42 dB with –80 dBm RF input
> 48 dB with –75 dBm RF input
Video Diff. Gain:
< 5%
Video Diff. Phase:
< 5 degrees
Chr. To Lum. Gain:
70% to 107%
Chr. To Lum. Delay: ±60 nS
Output Load Imp.:
75Ω
DC Clamping:
Back Porch with 0 V typical DC offset
AUDIO SECTION:
Audio Bandwidth:
50 Hz to 15 kHz (3 dB)
Harmonic Distortion: < 1% over 50 Hz to 15 kHz
Audio Output S/N:
> 12 dB with –85 dBm RF Input
Output Load Imp.:
600Ω
Output Level:
1.5 Vpp typical
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
43
ALARM SECTION:
Data Rate:
19,200 bps
Coding Scheme:
32 bit command/address, 8 bit data
with checksum
Output Level:
Reflects state of transmitter alarm
inputs – updated twice per second
POWER SECTION:
Input Voltage Range: 7 Vdc nominal, 6-9 Vdc
Max. Ripple Input:
1 Vpp
Current Consumption:450 mA nominal in receive mode and
RSSI mode
DATA PASS THROUGH MODE:
Protocol:
Simplex, 3-wire, RS-232 levels, using
serial port
Serial Port Settings: 1200, 2400, 4800, 9600 bps with
adjustable parity (even, odd, none –
8,N,1 Standard), configurable with
TrangoLink software
Latency:
< 15 mS end to end
BER:
< 1E10-6 at –80 dBm input signal level
Note: RS-422/485 interface available
with optional daughter board.
44 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
VRX5900 Receiver: Mechanical & Environmental
GENERAL:
Material:
Cast aluminum NEMA 4X rated
outdoor enclosure
Finish:
Off-white powdercoat
Size:
4.65” W x 8.8”L x 2.475”H without
antenna
Weight:
2.65 lb
CONNECTORS & INDICATORS:
RF Input:
SMA female connector
FCC Compliance:
The receiver shall comply with FCC
Part 15.203, FCC Part 15.207(a),
FCC Part 15 Subpart B, Industry
Canada Specifications (RSS 210
Issue 2)
PC Interface:
6 position, 4 conductor RJ11 female
right angle PCB mount
Video:
BNC female PCB mount
Audio:
Red RCA female PCB mount – R
Audio
White RCA female PCB mount – L
Audio (Mono)
Alarm/Power:
6 post terminal block (6-9 Vdc, GND,
ALARM 1, ALARM 2)
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
45
CONNECTORS & INDICATORS: (continued)
Controls:
Channel switch: momentary, toggles
through modes/channels
Stereo/Alarm switch: DPDT switch
allows selection of data/alarms or right
audio on 6.0 MHz subcarrier
Indicators:
4 channel LEDs that display the
current channel
ENVIRONMENTAL:
Operating Temp.:
-20 to 70 º C
Storage:
-40 to 85 º C
Humidity:
100% (enclosure)
Shock:
Sustain 3-axis drop from 5’
46 M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
Notes:
M-FALCON2 Rev B
Copyright © 2000 Trango Systems, Inc. (All rights reserved)
47


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 49
Creator                         : Microsoft Word
Create Date                     : 2002:02:07 11:25:48
Title                           : B.PDF
Author                          : dteng
Producer                        : Acrobat PDFWriter 4.05 for Windows

EXIF Metadata provided by EXIF.tools