Trans Electric BTX1000 Bluetooth Audio Adapter User Manual R5166G BTX 1200manual final

Trans Electric Co., Ltd. Bluetooth Audio Adapter R5166G BTX 1200manual final

Manual

1BTX-1200 Bluetooth audio transmitter With A2DP, CSR® aptX® supported Features  Connected upto 2 devices (headphone or music receiver)  aptX® normal and low latency codec support  SBC codec support  A2DP Bluetooth profile supported  33 feet (10M) effective range  Audio RL audio input What’s in the box Main Unit 3.5mm male → male audio cable
2USB for Power Audio In for TV or Audio Device Pairing Outlook Setup your BTX-1200 Before your connection, please make sure that you have Bluetooth headphone or music receiver in hands. BTX-1200 is a Bluetooth music transmitter and splitter, it can not be operated without Bluetooth headset or music receiver. Connection (TV audio connection) 1. Connect one 3.5mm end of the include audio to headphone jacket on the BTX-1200 2. Connect the other end to an audio output on your TV’s Headphone output or speaker output. Consult your TV user’s manual for more information on how to accomplish this. 3. Connect the USB Type A connector to the USB port of your TV set. Note: The USB port must have the powering capability of 500Ma 4. Connect the USB type A to an USB adaptor (option)
3Operation Connect to the first headset or music receiver 1. Take your Bluetooth headphone or Bluetooth music receiver 2. make it into “pairing” mode, please consult your manual for further information 3. The BTX-1200 will auto connect the “pairing” devices, when BTX-1200 and headphone or music receiver are connected, the LED on BTX-1200 will go permanent lighted. Connect to the second headset or music receiver 1. Take your second Bluetooth headphone or Bluetooth music receiver 2. make it into “pairing” mode, please consult your manual for further information 3. Press the “pairing” button on BTX-1200 for one second, the LED will blinking for seconds, BTX-1200 is searching for the second Bluetooth headset or music receiver, at the same time, the audio on first connected device will be muted. 4. when BTX-1200 and headphone or music receiver are connected, the LED on BTX-1200 will go permanent lighted Note: BTX-1200 can connect two Bluetooth A2DP receivers at the same time, in some scenario, if you want to connect another A2DP device, you need to reset the BTX-1200 for new connection. Reset Method Press the “pairing” key on BTX-1200 for 5 seconds, then release it, the LED on BTX-1200 will go blinking for searching “pairing” A2DP devices nearby. Note: the effective range of BTX-1200 is 33 feet (10M) (light of sight). For the best performance we recommend you to let BTX-1200 visible. Do not block the bluetooth antenna; otherwise the distance will be shorter.
4Indication of LED Troubleshooting You can solve your problems from this section, no music from your headset or music receiver.  Make sure the BTX-1200 is powered.  Make sure an audio cable is correctly and firmly connected to BTX-1200  Make sure that the audio source is correct and with audio out.  Make sure the volume of the audio out is set to a comfortable listening level  Make sure you are within range. Safety Warnings  BTX-1200 requires full connection and both hands to install.  Do not use BTX-1200 near water (for example, a bath tub, wash bowl, kitchen sink, laundry tub, wet basement, swimming pool, or other areas located near water).  Clean with dry cloth.  Unplug the BTX-1200 before cleaning.  Install BTX-1200 far away from heat sources.  Use only the attached accessories.  Unplug the BTX-1200 when unused for long time. *** aptX® software is copyright CSR plc or its group companies. All rights reserved. The aptX® mark and the aptX logo are trademarks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. Indication Meaning Description Flash once 1 sec per 5 secs Power on / Pairing Searching the device under pairing mode Permanent Lighted Connected Device and main unit are connected
5FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Part 15B compliance statement:Part 15B compliance statement:Part 15B compliance statement:Part 15B compliance statement:
6 — — — —

Navigation menu