Trans Lux Midwest orartion QP-100-RF Quick Pitch Speed Display Interface Unit User Manual Updated with RF Exposure Statement

Download:
Mirror Download [FCC.gov]
Document ID	121523
Application ID	DrxY8vsG6wN4SjvbnJpa5Q==
Document Description	Updated with RF Exposure Statement
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	40.71kB (508929 bits)
Date Submitted	2000-10-18 00:00:00
Date Available	2000-10-31 00:00:00
Creation Date	2000-10-18 12:23:06
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2000-10-18 12:23:07
Document Title	Updated with RF Exposure Statement

Interface Control
Instructions
The Quick Pitch Interface Control accepts data from external devices, such as radar guns and track timing systems, interprets
the data and transmits it to a compatible Fair-Play display device.
Setup
Typical Setup:
1. Connect your external device (e.g. radar gun, timing system) to the radar jack or RS232 jack with the appropriate cable
to the interface cable.
2. Connect the 12VDC power supply to the interface control and plug into a 110VAC outlet.
3. If the display device is to be connected by wire, plug the control wire into the RS485 jack. Note: Control cable should
not be used if the optional radio transmitter is installed.
Advanced Setup:
1. Within the Interface Control is a 16 position mode switch. The mode switch controls the format of the data leaving the
interface control. The mode switch should be set in position “0” for is the optional radio transmitter is used and in
position “1” if cable is to be used. The mode switch is accessed by removing the front cover, unplugging the pushbutton switches, unscrewing the back cover, and withdrawing the back cover and PCB from the housing case. The mode
switch is the lower of the two switches if the optional radio transmitter is installed.
2. If the optional radio transmitter is to be used, the channel selected on the transmitter must be set to the same channel as
the receiver. The transmitter is mounted within the interface control and is the upper of the printed circuit cards.
Positions “1” to “D” are all active channels. Positions “0”, “E”, and “F” are inactive.
Operation
The interface control has an automatic and manual mode of operation. In the automatic mode, the Interface Control
automatically identifies valid information and transmits it to the display and then clears the display 15 seconds later. In the
manual mode, the Interface Control presents the data that it proposes to transmit on the Interface Control readout. Upon
inspection, the user can either “Send” the data to the display or “Clear” the information and wait until new data is available.
Automatic Operation:
1. Select Auto on the mode select switch located on the back cover.
2. Turn the power on to the Interface Control and your external device.
3. Configure the external device so it is sending properly formatted data.
4. Correct data should automatically be sent to the connected display.
Manual Operation:
1. Turn the power on to the Interface Control and your external device.
2. Configure the external device so it is sending properly formatted data.
3. Wait for valid data to appear on the readout. If invalid data appears, push “Clear”
4. When valid data appears on the readout, push “Send” and the information will be sent and shown on the external display.
5. Push “Clear” to remove data and begin accepting new data.
Customer Service
Should you encounter problems with the Quick Pitch Interface Control, please contact Trans-Lux Customer Service
at 1-800-462-2716.
Optional Transmitter Note
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
To comply with FCC RF exposure require ments for mobile transmitting devices, this transmitter should only be used
or installed at locations where there is at least 20 cm separation distance between the antenna and all persons.
Warning - Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2000:10:18 12:23:06
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2000:10:18 12:23:07-04:00
Page Count                      : 1

EXIF Metadata provided by EXIF.tools