TransCore 05760 LOW POWER TRANSMITTER User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	1582128
Application ID	uxMqlE0uxiDYnWi82+umlw==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.73kB (121604 bits)
Date Submitted	2011-11-16 00:00:00
Date Available	2011-12-31 00:00:00
Creation Date	2003-04-07 13:23:32
Producing Software	Acrobat Distiller 8.2.6 (Windows)
Document Lastmod	2011-09-28 14:24:36
Document Title	600139 IAG Standard OBU_small outline Instructions.fm
Document Creator	FrameMaker 7.0
Document Author:	jstikar

Installation Instructions
for Standard On-Board Units (small outline)
600139 09/11
General Installation Information
Metallized Windshields: Some vehicle windshields contain a metallic treatment that could prevent an interior
windshield-mounted on-board unit (OBU) from working correctly. If you have a vehicle with a metallized
windshield, you may need to install an exterior OBU on your vehicle instead of the interior windshield-mounted
OBU. Contact your local OBU customer service center for more information. If your vehicle’s metallized
windshield has a metal-free zone that usually is located near the rearview mirror.
Metal-Free Zone: Some vehicle metallized windshields have a metal-free zone, if your windshield has this zone,
center the OBU in that area and follow the installation instructions listed on this page.
Tinted Windshields: Some vehicles have a metallic tint across the top of the windshield that might interfere with
reading the OBU. If your windshield has this metallic tint, install the OBU at least 2 inches (5.1 cm) below the
tinted area. Nonmetallic tint does not affect OBU performance.
Metal Sun Visors: Some vehicles have an exterior-mounted sun visor that might interfere with reading the OBU. If
your vehicle has this visor, mount the OBU at least 2 inches (5.1 cm) below the visor.
Required Supplies
•
•
Standard OBU (small outline)
Commercial glass cleaner and paper towels
OBU Installation and Removal Procedures
The OBU may be equipped with hook-and-loop strips, double-sided tape strips (secure mount), or suction cups.
To install the OBU
1. Choose the location for your OBU (Figure 1).The OBU should be mounted approximately 1 inch (2.54 cm)
below the rearview mirror post.
Figure 1. Optimum Locations for OBU Performance
2.
Clean and dry the interior windshield surface completely before affixing the fastener strips. The windshield
temperature must be at least 68ºF (20ºC) for optimum bonding.
3.
Peel off the double-faced barrier on the hook-and-loop or double-sidedStape
P strips
E C I(Figure
F I C2).
A T I O N S
Note: When installing the OBU using hook-and-loop strips or double-sided tape (secure mount) for the first
time, leave the OBU in place for at least 24 hours to allow the adhesive to cure.
Figure 2 Remove Backing to Expose Adhesive on Hook-and-Loop or Double-sided Strips
4.
If using suction cups, moisten the cups and stick the OBU to the windshield.
5.
Holding the OBU so that the arrows on the front label point up as shown in Figure 3, press the OBU against
the windshield and hold for 10 seconds.
Figure 3 Correct Tag Orientation
6.
To remove an OBU mounted with hook-and-loop or suction cup from the windshield, grip the OBU at the
top and bottom sides. Gently lift the OBU away from the windshield on one end until the OBU is free from
the windshield. Be careful not to hit the rearview mirror.
NO UNAUTHORIZED MODIFICATIONS STATEMENT
Caution: This equipment may not be modified, altered, or changed in any way without permission from TransCore, LP. Unauthorized modification may void the equipment
authorization from the FCC and will void the TransCore warranty.
RADIO FREQUENCY INTERFERENCE STATEMENTS
Note: This device complies with Part 15 of the FCC Rules and the Industry Canada Licence-Exempt RSS Standards. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Note: Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur del’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
www.transcore.com
© 2010 TC License, Ltd. All rights reserved. TRANSCORE is a registered trademark of TC License, Ltd. All other trademarks listed are the property of their respective
owners. Contents subject to change. Printed in the U.S.A.
600139 09/11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2011:09:28 14:24:36Z
Create Date                     : 2003:04:07 13:23:32Z
Format                          : application/pdf
Title                           : 600139 IAG Standard OBU_small outline Instructions.fm
Creator                         : jstikar
Producer                        : Acrobat Distiller 8.2.6 (Windows)
Document ID                     : uuid:b8892fa0-1b53-4b79-916b-295d17bcb8e0
Instance ID                     : uuid:39cd138a-00b5-48cb-bb41-a2016bd38937
Page Count                      : 2
Author                          : jstikar

EXIF Metadata provided by EXIF.tools