Transtek Medical Electronics LS810-BS1 Blood Pressure Monitor User Manual

Guangdong Transtek Medical Electronics Co.,Ltd Blood Pressure Monitor Users Manual

Users Manual

User ManualBlood Pressure Monitor LS810-BSPlease do read the user manual carefully and thoroughly so as to ensure the safe usage of this product, and keep the manual well for your further reference in case you have problems.Thank you very much for selecting TRANSTEK Blood Pressure Monitor LS810-BS.Wrist TypeVersion:1.0Guangdong Transtek Medical Electronics Co., Ltd.Zone B, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China MEMSET
1INTRODUCTION .............................................................2Indications for UseLCD Display SignalMonitor ComponentsListBEFORE YOU START ........................................................9MEASUREMENT .............................................................13INFORMATION FOR USER .................................................... 18Tips for MeasurementMaintenanceABOUT BLOOD PRESSURE....................................................20What are systolic pressure and diastolic pressure?What is the standard blood pressure classification?Irregular heartbeat detectorWhy does my blood pressure fluctuate throughout the day?Why do I get a different blood pressure at home compared to the hospital?Is the result the same if measuring on the right wrist?TROUBLESHOOTING .........................................................22SPECIFICATIONS ............................................................. 23THE MATCHED COMPONENTS ............................................... 24CONTACT INFORMATION...................................................... 24Safety InformationPower Supply and Charge PowerSetting Date and Time Tie the CuffStart MeasurementData Management .................................. 16Recall the RecordsDelete the Records.........................COMPLIED STANDARDS LIST .................................. 26Table of Contents...............Measurement PrincipleGeneral DescriptionEMC GUDIANCE ...................................................... 27......Table of ContentsActivate Your Blood Pressure MonitorFCC STATEMENT ............................................................. 25
INTRODUCTION INTRODUCTION FEATURES:Systolic Blood PressureDiastolic Blood PressurePulse RateMemory: Up to 60 pieces of recordsThis product uses the Oscillometric Measuring Method to detect blood pressure. Before every measurement, the unit establishes a “zero point” equivalent to the atmospheric pressure. Then it starts inflating the cuff. Meanwhile, the unit detectspressure oscillation generated by beat-to-beat pulsatile, which is used to deter-mine the systolic pressure and diastolic pressure as well as pulse rate. Measurement PrincipleGeneral DescriptionThe signs below might be in the user manual, labeling or other components. They are the requirement of standard and using. Safety Information23Indications for UseThe Transtek Blood Pressure Monitor is digital monitors intended for use in measuring blood pressure and heartbeat rate with wrist circumference rangingfrom 13.5 cm to 21.5 cm ( about 5-8.5 inches ). It is intended for adult indoor use only.Thank you for selecting TRANSTEK blood pressure monitor (LS810-BS).The monitor features blood pressure measurement, pulse rate measurementand the result storage. The design provides you with two years of lifetime.Readings taken by the LS810-BS are equivalent to those obtained by a trainedobserver using the cuff and stethoscope auscultation method.This manual contains important safety and care information, and provides stepby step instructions for using the product.Please do read this user manual carefully and thoroughly before use.Symbol for “ENVIRONMENT PROTECTION - Electrical waste products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice”SNSymbol for “TYPE BF APPLIED PARTS”Symbol for “THE OPERATION GUIDE MUST BE READ”Symbol for “MANUFACTURER”Symbol for “SERIAL NUMBER”Symbol for “DIRECT CURRENT”Symbol for “MANUFACTURE DATE”Caution: These notes must be observed to prevent any damage to the device.Symbol for “Recycle”The Green Dot is the license symbol of a European network of industry-funded systems for recycling the packaging materials of consumer goods.Symbol for “Class II Equipment” For indoor use onlyF1T1A/250V Φ3.6*10CCC Symbol for “Including RFtransmitter”Contraindications1.The device is not suitable for use on may be pregnant women or pregnant women.2.The device is not suitable for use on patients with implanted,electrical devices,such as cardiac pacemakers, defibrillators.
INTRODUCTION INTRODUCTION45CAUTION* This device is intended for adult use in homes only. * The device is not suitable for use on neonatal patients, pregnant women,patients with implanted, electronical devices, patients with pre-eclampsia, premature ventricular beats, atrial fibrillation, peripheral, arterial disease and patients undergoing intravascular therapy or arterio-venous shunt or people who received a mastectomy. Please consult your doctor prior to using the unit if you suffer from illnesses.* The device is not suitable for measuring the blood pressure of children. Ask your doctor before using it on older children.* The device is not intended for patient transport outside a healthcare facility.* The device is not intended for public use.* This device is intended for no-invasive measuring and monitoring of arterial blood pressure.It is not intended for use on extremities other than the wrist or for functions other than obtaining a blood pressure measurement.* Do not confuse self-monitoring with self-diagnosis. This unit allows you to monitor your blood pressure.Do not begin or end medical treatment without asking a physician for treatment advice.* If you are taking medication,consult your physician to determine the most appropriate time to measure your blood pressure. Never change a prescribed medication without consulting your physician.* Do not take any therapeutic measures on the basis of a self measurement. Never alter the dose of a medicine prescribed by a doctor. Consult your doctor if you have any question about your blood pressure.* When the device was used to measure patients who have common arrhythmias such as atrial or ventricular premature beats or atrial fibrillation, the best result may occur with deviation. Please consult your physician about the result.* Don't kink the connection tube during use, otherwise, the cuff pressure may continuously increase which can prevent blood flow and result in harmful injury to the PATIENT.* When using this device, please pay attention to the following situation which may interrupt blood flow and influence blood circulation of the patient, thus cause harmful injury to the patient: connection tubing kinking too frequent and consecutive multiple measurements; the application of the cuff and its pressurization on any wrist where intravascular access or therapy, or an arterio-venous (A-V) shunt, is present; inflating the cuff on the side of a mastectomy.* Warning: Do not apply the cuff over a wound;otherwise it can cause further injury.*Do not inflate the cuff on the same limb which other monitoring ME equipment is applied around simultaneously, because this could cause temporary loss of function of those simultaneously-used monitoring ME equipment.*On the rare occasion of a fault causing the cuff to remain fully inflated during measurement, open the cuff immediately. Prolonged high pressure (cuff pressure ＞ 300mmHg or constant pressure ＞ 15mmHg for more than 3 minutes) applied to the wrist may lead to an ecchymosis.*Please check that operation of the device does not result in prolonged impairment of patient blood circulation.* When measurement, please avoid compression or restriction of the connection tubing.* The device cannot be used with HF surgical equipment at the same time.* The ACCOMPANYING DOCUMENT shall disclose that the SPHYGMOMANOMETER was clinically investigated according to the requirements of ISO 81060-2:2013.* To verify the calibration of the AUTOMATED SPHYGMOMANOMETER, please contact the manufacturer.* This device is contraindicated for any female who may be suspected of, or is pregnant. Besides providing inaccurate readings, the effects of this device on the fetus are unknown.* Too frequent and consecutive measurements could cause disturbances in blood circulation and injuries.* This unit is not suitable for continuous monitoring during medical emergencies or operations.Otherwise, the patient’s wrist and fingers will become anaesthetic, swollen and even purple due to a lack of blood.* When not in use, store the device with the adapter in a dry room and protect it against extreme moisture, heat, lint, dust and direct sunlight. Never place any heavy objects on the storage case.* This device may be used only for the purpose described in this booklet. The manufacturer cannot be held liable for damage caused by incorrect application.*This device comprises sensitive components and must be treated with caution. Observe the storage and operating conditions described in this booklet.CAUTION* The maximum temperature that the applied part can be achieved is 42.5℃ while the environmental temperature is 40℃.* The equipment is not AP/APG equipment and not suitable for use in the presence of a flammable anesthetic mixture with air of with oxygen or nitrous oxide.* Warning: No servicing/maintenance while the ME equipment is in use.* The patient is an intended operator.* The patient can measure, transmit data and charge power under normal circumstances and maintain the device and its accessories according to the user manual.* To avoid measurement errors, please avoid the condition of strong electromagnetic field radiated interference signal or electrical fast transient/burst signal.* The blood pressure monitor, its adaptor, and the cuff are suitable for use within the patient environment. If you are allergic to polyester, nylon or plastic, please don't use this device. * During use, the patient will be in contact with the cuff. The materials of the cuff have been tested and found to comply with requirements of ISO 10993-5:2009 and ISO 10993-10:2010. It will not cause any potential sensization or irritation reaction.* Adaptor is specified as a part of ME EQUIPMENT.* If you experience discomfort during a measurement, such as pain in the wrist or other complaints, press the START/STOP button to release the air immediately from the cuff. Loosen the cuff and remove it from your wrist.* If the cuff pressure reaches 40 kPa (300 mmHg), the unit will automatically deflate. Should the cuff not deflate when pressures reaches 40 kPa (300 mmHg), detach the cuff from the wrist and press the START/STOP button to stop inflation.* Before use, make sure the device functions safely and is in proper working condition. Check the device, do not use the device if it is damaged in any way. The continuous use of a damaged unit may cause injury, improper results, or serious danger.* Do not wash the cuff in a washing machine or dishwasher!* The service life of the cuff may vary by the frequency of washing, skin condition, and storage state. The typical service life is 10000 times.* It is recommended that the performance should be checked every 2 years and after maintenance and repair, by retesting at least the requirements in limits of the error of the cuff pressure indication and air leakage (testing at least at 50mmHg and 200mmHg).* Please dispose of ACCESSORIES, detachable parts, and the ME EQUIPMENT according to the local guidelines.* Manufacturer will make available on request circuit diagrams, component part lists, descriptions, calibration instructions,etc., to assist to service personnel in parts repair.* The plug/adapter plug pins insulates the device from the main supply. Do not position the device in a position where it is difficult to disconnect from the supply mains to safely terminate operation of ME equipment.* The operator shall not touch output of batteries /adapter and the patient simultaneously.* Cleaning :Dust environment may affect the performance of the unit. Please use the soft cloth to clean the whole unit before and after use. Don’t use any abrasive or volatile cleaners.* The device doesn’t need to be calibrated within two years of reliable service.* If you have any problems with this device, such as setting up, maintaining or using, please contact the SERVICE PERSONNEL of Transtek. Don’t open or repair the device by yourself in the event of malfunctions. The device must only be serviced, repaired and opened by individuals at authorized sales/service centers.* Please report to Transtek if any unexpected operation or events occur.* Keep the unit out of reach of infants, young children or pets to avoid inhalation or swallowing of small parts. It is dangerous or even fatal.
INTRODUCTION INTRODUCTION6LCD Display Signal7CAUTION * Be careful to strangulation due to cables and hoses, particularly due to excessive length.* At least 30 min required for ME equipment to warm from the minimum storage temperature between uses until it is ready for intended use. At least 30 min required for ME equipment to cool from the maximum storage temperature between uses until it is ready for intended use.* This equipment needs to be installed and put into service in accordance with the information provided in the ACCOMPANYING DOCUMENTS;*Wireless communications equipment such as wireless home network devices, mobilephones, cordless telephones and their base stations, walkie-talkies can affect thisequipment and should be kept at least a distance d away from the equipment. The distanced is calculated by the MANUFACTURER from the 80MHz to 5.8 GHz column of Table 4 andTable 9 of IEC 60601-1-2:2014, as appropriate.* Please use ACCESSORIES and detachable partes specified/ authorised by MANUFACTURE. Otherwise, it may cause damage to the unit or danger to the user/patients.* There is no luer lock connectors are used in the construction of tubing, there is a possibility that they might be inadvertently connected to intravascular fluid systems, allowing air to be pumped into a blood vessel.* Please use the device under the environment which was provided in the user manual. Otherwise, the performance and lifetime of the device will be impacted and reduced.* There is a PTC current limiter in the monitor, which specification is 8V and 0.5A. When the voltage and current exceed the limiting value, the monitor will stop working. Systolic Blood Pressure High blood pressureDiastolic Blood Pressure Low blood pressureUnit Measurement unit of blood pressure(1 mmHg=0.133 kPa)Time Hour:Minute (Month/Day/Year)Low Battery Low battery and please charge the power.MemoryPulse in beats per minutePulse display Heartbeat Blood pressure monitor is detecting a heartbeat during measurement.Indicate it is in the memory mode and which group of memory it is.Irregular heartbeat Blood pressure monitor is detecting anirregular heartbeat during measurement.
SYSTOLICDIASTOLICMEM/UPBUTTONSET/DOWN BUTTONSTART/STOP BUTTONCUFF(Type BF applied part)PULSE RATETIMEUSB InterfaceMonitor ComponentsList1.Blood Pressure Monitor (LS810-BS)2.USB Cable and AC Adaptor3.User Manual81. The battery of LS810-BS is built-in rechargeable lithium-ion battery, the battery current is 420 mAh.2. Please use the AC adaptor and USB cable to charge the battery, just like the following picture: Power Supply and Charge PowerCharging the power under following circumstances:displays on the LCDThe LCD display dimsWhen powering on the monitor, the LCD doesn’t light up.AC adaptor 9Component list of pressure measuring system1 PCBA2 Air pipe3 Pump4 Valve5 CuffBEFORE YOU STARTINTRODUCTION CAUTION * The battery of LS810-BS is built-in rechargeable lithium-ion battery, please do not disassemble it by the unauthorized maintenance personel. * Under the normal using, it can charge power about 300 times, if the battery cannot charge the power normally or the blood pressure monitor cannot use normally, please connect with the authorized maintenance personel.If measured three times per day, and the battery is fully charged, it can be used for about 20 days.* Storge and use the blood pressure monitor at the cool, dry and ventilated environment. Avoid to approach to the fire and the heat source, or it will cause the battery explode.* Only can use the Transtek’s authorized AC Adaptor (Model:BLJ06L050100U-S,BLJ06L050100U-B,BLJ06L050100U-U,BLJ06L050100U-V) to charge the power. You cannot use the blood pressure monitor during the process of charging.* During the process of charging, the blood pressure monitor display When the charging is finished, please pull the plug in time.* When charging, shall not touch charging connector and the patient simultaneously. MEMSET ( Model: BLJ06L050100U-S, BLJ06L050100U-B, BLJ06L050100U-U, BLJ06L050100U-V)
10 11Activate Your Blood Pressure MonitorWhen you get the Blood Pressure Monitor, the first thing you must do is to activate it.Please press and hold the SET button to activate it,then it will enter the setting mode.BEFORE YOU STARTCAUTIONBEFORE YOU START• Do not attempt to replace your blood pressure monitor’s battery. It is built-in and not changeable.• Only charge the battery in accordance with the user instructions supplied with the blood pressure monitor.• Avoid charging your blood pressure monitor in extremely high or low temperatures.• Do not use your blood pressure monitor while you are charging it.• Do not attempt to disassemble the blood pressure monitor or force open the built-in battery.• Do not clean the blood pressure monitor when it is being charged. Always unplug the charger first before cleaning the blood pressure monitor.• Do not dispose of your blood pressure monitor in a fire. The battery could explode causing injury or death.• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.Setting Date and Time2.As pictured in the right, the blinking numeral representing [HOUR]. Press “MEM” button to change the numeral. Each press will increase the numeral by one in a cycling manner. 1.When the monitor is OFF, press and hold “SET” button for 3 seconds to enter Time Setting Mode.3.Press “SET” button again to confirm [HOUR]. Then the numeral representing [MINUTE] blinks. Please proceed to time setting before your initial use so as to ensure each piece of record are labled with a time stamp. (Year Range: 2012-2052; Time Format: 12 Hours)
12 13MEMSETMEASUREMENTBEFORE YOU STARTTie the Cuff1.2.3.4.5. Remove all accessories (watch, bracelet,etc) from your wrist. If your physician has diagnosed you with poor circulation in your wrist, use the other one.Roll or push up your sleeve to expose the skin.Apply the cuff to your wrist with your palm facing up.Position the edge of the cuff about 1cm~2cm from wrist joints.Fasten the wrist cuff around your wrist, leaving no extra room between the cuff and your skin. If the cuff is too loose, the measurement will not be accurate.Sit comfortably with your tested wrist resting on a flat surface. Place your elbow on a table so that the cuff is at the same level as your heart. Turn your palm upwards. Sit upright in a chair, and take 5-6 deep breaths.Rest for 5 minutes before first measuring.Wait at least 3 minutes between measurements. This allows your blood circulation to recover.The patient must relax as much as possible and do not move and talk during the measurement procedure.For a meaningful comparison, try to measure under similar conditions. For example, take daily measurements at approximately the same time, on the same wrist, or as directed by a physician.6.7.Take the measurement in a silent room.The cuff should maintain at the same level as the right atrium of the heart.Please sit comfortably. Do not cross your legs and keep your feet flat on the ground.Keep your back against the backrest of the chair.Helpful tips for Patients, especially for Patients with Hypertension:4.Repeat step 2 and 3 to confirm [MINUTE].5.Repeat step 2 and 3 to confirm [MONTH], [DAY] and [YEAR].6.After confirming [YEAR], the LCD will display “doNE” and the monitor will shut off.
14 15MEASUREMENTMEASUREMENTAdjust the zero.Inflating and measuring. Display and save the measuring result.STARTSTOP1.After correctly positioning the cuff, press START button to turn on the monitor, and it will complete the measurement process. Start Measurement4.Press STOP button to turn off the monitor. Otherwise it will power off.2.This device will proceed to data transmission after measurement. The symbol blinks on the LCD indicates data is transmitting. 3.If the data is successfully transmitted, the LCD will then display “ ”and“dONE”. If the data transmission fails, the LCD will display “ ”and “ Err ” instead. CAUTION 1. 2. Interference may occur in the vicinity of equipment marked with the following symbol . And LS810-BS may interfering vicinity electrical equipment.Sensitive people, including pregnant women pre-eclamptic and those who implanted medical electronic instruments, should avoid using the unit whenever possible.Keep the monitor at least 20 centimeters away from the human body (especially the head) when the data transmission is proceeding after measurement.To enable the data transmission function, this product should be paired to Bluetooth end at 2.4 GHz.How to mitigate possible interference?The range between the device and BT end should be reasonably close, from 1 meter to 10 meters. Please ensure no obstacles between the device and BT end so as to obtain quality connection and to lower the RF output range.To avoid interference, other electronic devices (particularly those with wireless transmission / Transmitter) should be kept at least 1 meter away from the monitor.
16 17DATA MANAGEMENT DATA MANAGEMENTRecall the Records1.Press “MEM” button to access the memory. The monitor will display the calculated value of the latestreadings first.2. Press “MEM/UP” button or “SET/DOWN” button to rotate the history records.“MEM/UP” to go forward;“SET/DOWN” to go backward.The most recent record (1) is shown first. Each new measurement is assigned to the first (1) record. All other records are pushed back one digit (e.g., 2 becomes 3, and so on), and the last record (60) is dropped from the list.CAUTION When you did not obtain the accurate measurement, you can clear all the measuring results by following steps below.Delete the Records1.Under Memory Recalling Mode, press and hold both the “MEM” button and the “SET” button for 3 seconds.2.The LCD will display “dEL dONE”, indicating that memory clearing is complete.And then it will shutdown. Under Memory Recalling Mode, if you wish to give up clearing, press “START/STOP” to turn off the monitor.3.When there is no memory in the monitor, if you press the “MEM” button to look up history, the LCD will display as pictured to the right.CAUTIONBluetooth Module No.:AW2540 RF Frequency Range:2402~2480MHz Supply Voltage:3.3V Transmitting Distance:10M List of compatible devices:For iOS devices:The operating system must be iOS 8 or more, such as iPhone4S, iPhone 5/5C/5S, iPhone 6/6 Plus and so on.For Android devices:The operating system must be 4.3 or more.
Tips for MeasurementWithin 1 hour after dinner or drinkingWithin 20 minutes after taking a bathIn a very cold environmentImmediate measurement after tea, coffee, smoking When talking or moving your fingersWhen you want to discharge urineMEMSETMEMSETMEMSET18MaintenanceTo obtain the best performance, please follow the instructions below.Put in a dry place and avoid the sunshineAvoid shaking and collisions.Use the slightly damp cloth to remove the dirt.Avoid immersing it in the water.Clean it with a dry cloth in case.Avoid dusty environment and unstable temperature surroundingAvoid washing the cuffMEMSETMEMSETMEMSET19Measurements may be inaccurate if taken in the following circumstances.INFORMATION FOR USER INFORMATION FOR USER
2120Why does my blood pressure fluctuate throughout the day? MEMSETMEMSET1. Individual blood pressure varies multiple times everyday. It is also affected by the way you tie your cuff and your measurement position, so please take the measurement under the same conditions.2.If the person takes medicine, the pressure will vary more.3.Wait at least 3 minutes for another measurement.The blood pressure is different even throughout the day due to weather, emotion, exercise etc, Also, there is the “white coat” effect, which means blood pressure usually increases in clinical settings.What you need to pay attention to when you measure your blood pressure at home: If the cuff is tied properly. If the cuff is too tight or too loose.If the cuff is tied on the wrist.If you feel anxious.Taking 2-3 deep breaths before beginning will be better for measuring. Advice: Relax yourself for 4-5 minutes until you calm down.It is ok for both wrists, but there will be some different results for different people. We suggest you measure the same wrist every time.Why do I get a differentblood pressure at homecompared to the hospital?Is the result the same ifmeasuring on the rightwrist?ABOUT BLOOD PRESSURE ABOUT BLOOD PRESSUREWhat are systolic pressure and diastolic pressure? pressartery veinblood dischargingSystolicrelaxblood enteringDiastolic What is the standard blood pressure classification?When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.Irregular Heartbeat DetectorCAUTIONThe appearance of the IHB icon indicates that a pulse irregularity consistent with an irregular heartbeat was detected during measurement. Usually this is NOT a cause for concern. However, if the symbol appears often, we recommend you seek medical advice. Please note that the device does not replace a cardiac The chart on the right is the standard blood pressure classifi-cation published by AmericanHeart Association (AHA).AHA Home Guideline for Upper Limit of Normal BPPlease consult a physician if your measuring result falls outside the range. Please note that only a physician can tell whether your blood pressure value has reached a dangerous point.CAUTIONSYS 135 mm HgDIA 85 mm HgBlood Pressure CategoryNormalPrehypertensionHigh Blood Pressure(Hypertension) Stage 1High Blood Pressure(Hypertension) Stage 2Hypertensive Crisis(Emergency care needed)SystolicmmHg (upper#)DiastolicmmHg (lower#)less than 120120-129130-139140 or higherHigher than 180andororand/orless than 8080-8990 or higherHigher than 120This chart reflects blood pressure categories defined by American Heart Association.An irregular heartbeat is detected when a heartbeat rhythm varies while the unit is measuring the systolic and diastolic blood pressure.During each measurement, the monitor records all the pulse intervals and calculate the average ; if there are two or more pulse intervals ,the difference between each interval and the average is more than the average value of ±25% , or there are four or more pulse intervals ,the difference between each interval and the average is more thanthe average value of ±15%,the irregular heartbeat symbol appears on the display when themeasurement results are appear.and less than 80
22Power supply 3.7V 420mAH Built-in rechargeable lithium-ion battery, 5V 1A USB AC AdaptorDisplay mode Digital LCD V.A.46.5mmx36.5mmMeasurement mode Oscillographic testing modeMeasurement rangeAccuracyNormal working conditionStorage & transportationconditionMeasurement perimeterof the wrist About 13.5cm-21.5cmWeight Approx.110gExternal dimensionsAttachmentApprox.79.8mm×72.5mm×13.2mmUSB cable, AC Adaptor,user manualMode of operation Continuous operationDegree of protection Type BF applied partProtection against ingress of waterIP22, It means the device could protectedagainst solid foreign objects of 12.5 mm andgreater, and against vertically falling waterdrops when ENCLOSURE tilted up to 15°Software versionDevice classificationV01 004Battery Powered Mode: Internally Powered ME EquipmentWARNING: No modification of this equipment is allowed.Pressure:5℃-40 ℃within±3mmHg(0.4kPa) pulse value:±5%AC Adaptor charged Mode: Class II ME Equipment23SPECIFICATIONSTROUBLESHOOTINGRated cuff pressure: 0mmHg~299mmHg(0kPa ~ 39.9kPa)Measurement pressure: SYS: 60mmHg~230mmHg (8.0kPa~30.7kPa) DIA: 40mmHg~130mmHg (5.3kPa~17.3kPa)Pulse value: (40-199)beat/minuteThis section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the products not operating as you think it should, check here before arranging for servicing.PROBLEM SYMPTOM CHECK THIS REMEDYNo powerLowbatteriesErrormessageDisplay is dim orwill not light up. Power is exhausted.Charge the power.Show onthe display Power is low.E 2 showsRelax for a momentand then measure again.Movement can affect themeasurement.Relax for a moment and then measure again.E 3 showsE 4 shows Relax for a moment andthen measure again.EExx,shows on the display.A calibration erroroccurred.Retake the measurement.If the problem persists,contact the retailer or ourcustomer service department for further assistance.Refer to the warranty for contact information and return instructions.The measurement process does not detect the pulse signal.Loosen the clothing on the arm and then measure again.Charge the power.The cuff is not secure orvery tigh.E 1 shows Refasten the cuff and thenmeasure again.“out” showsOut of measurementrangeThe treatment of themeasurement failed.The monitor detectedmotion,talking or thepluse is too poorwhile measuring.(Excluding the dry cells)Temperature:-20°C to +60°CA relative humidity range of ≤ 93%, non-condensing, at a water vapour pressure up to 50hPaA temperature range of :+5°C to +40°C A relative humidity range of 15% to 90%, non-condensing, but not requiring a water vapour partial pressure greater than 50 hPaAn atmospheric pressure range of : 700 hPa to 1060 hPa
2425Please use the TRANSTEK authorized adaptor100-240V, 50-60Hz,0.18A5.0V 1.0AAdaptorType:Input:Output:The Matched ComponentTHE MATCH COMPONENT FCC STATEMENTFor more information about our products, please visit www.transtek.cn.you can get customer service, usual problems and customer download, transtek will serve you anytime.Contact InformationManufactured by:Company:Address:Guangdong Transtek Medical Electronics Co., Ltd.Zone B, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China Guangdong Transtek Medical Electronics Co., Ltd.FCC StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.FCC ID:OU9LS810-BS1BLJ06L050100U-S,BLJ06L050100U-B,BLJ06L050100U-U,BLJ06L050100U-V
EMC GUIDANCE26 27COMPLIED STANDARDS LISTComplied Standards ListEN ISO 14971:2012 / ISO 14971:2007 Medical devices - Application of risk management to medical devicesEN 1041:2008 Information supplied by the manufacturer of medical devicesEN 60601-1:2006/ IEC 60601-1:2005+A1:2012 Medical electrical equipment - Part 1: General requirements for basic safety and essential performanceEN 60601-1-11:2015/ IEC 60601-1-11:2015 Medical electrical equipment - Part 1-11: General requirements for basic safety and essential performance - Collateral standard: Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environmentEN 60601-1-2:2015/ IEC 60601-1-2:2014 Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral standard: Electromagnetic disturbances - Requirements and testsEN ISO 81060-1:2012 Non-invasive sphygmomanometers - Part 1: Requirements and test methods for non-automated measurement typeEN 1060-3:1997+A2:2009 Non-invasive sphygmomanometers - Part 3: Supplementary requirements for electro-mechanical blood pressure measuring systemsEN 1060-4:2004 Non-invasive sphygmomanometers - Part 4: Test procedures to determine the overall system accuracy of automated non-invasive sphygmomanometersEN 60601-1-6:2010/IEC 60601-1-6:2010+A1:2013 Medical electrical equipment - Part 1-6: General requirements for basic safety and essential performance - Collateral standard: UsabilityEN 62366-1:2015/ IEC 62366-1:2015 Medical devices - Part 1: Application of usability engineering to medical devicesEN 62304:2006/AC: 2008 / IEC 62304:2006 Medical device software - Software life-cycle processesRisk managementLabelingUser manualGeneral Requirements for SafetyElectromagneticcompatibilityPerformancerequirementsClinical investigationUsabilitySoftware life-cycle processesBio-compatibilityISO 10993-1:2009 Biological evaluation of medical devices- Part 1: Evaluation and testing within a risk management processISO 10993-5:2009 Biological evaluation of medical devices - Part 5: Tests for in vitro cytotoxicityISO 10993-10:2010 Biological evaluation of medical devices - Part 10: Tests for irritation and skin sensitizationEN ISO 15223-1:2016 / ISO 15223-1:2016 Medical devices. Symbols to be used with medical device labels, labelling and information to be supplied. Part 1 : General requirementsIEC 80601-2-30:2013 Medical electrical equipment- Part 2-30: Particular requirements for the basic safety and essential performance of automated non-invasive sphygmomanometersISO 81060-2:2013 Non-invasive sphygmomanometers - Part 2: Clinical validation of automated measurement typeEMC Guidance1)This product needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided,and this unit can be affected by portable and mobile RF communications equipment.2)* Do not use a mobile phone or other devices that emit electromagnetic fields, near the unit. This may result in incorrect operation of the unit.3)Caution: This unit has been thoroughly tested and inspected to assure proper performance and operation!4)* Caution: This machine should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, this machine should be observed to verify normal operation in the configuration in which it will be used.Table 1 Guidance and manufacturer’s declaration – electromagnetic emissionsRF emissions CISPR 11 Group 1 Class B Class ACompliesComplianceHarmonic emissions IEC 61000-3-2Voltage fluctuations/ flicker emissions IEC 61000-3-3 RF emissions CISPR 11Emissions test Electromagnetic environment - guidanceThe device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.The device uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.The device is suitable for use in all establishments,other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
28EMC GUIDANCE29EMC GUIDANCE Guidance and manufacturer’s declaration – electromagnetic immunity Immunity test ±8 kV contact±15 kV air ±8 kV contact±15 kV air ±2 kV power supply lines: line(s) to line(s): ±1 kV line(s) to earth: ±2 kV 0%UT; 0.5 cycleAt 0°, 45°, 90°, 135°,180°,225°,270° and 315°0%UT ; 1 cycle and 70%UT ; 25/30 cyclesSingle phase: at 0°0% UT ; 300 cycle30 A/m50Hz/60HzNOTE UT is the a.c. mains voltage prior to application of the test level. Table 2 Compliance levelElectrostatic discharge (ESD) IEC 61000-4-2 Electromagnetic environment - guidance30 A/m50Hz/60HzPower frequency (50Hz/60Hz) magnetic field IEC 61000-4-8 Voltage dips, short interruptionsand voltagevariations on power supply input linesIEC 61000-4-11 Electrical fast transient/burst IEC 61000-4-4 SurgeIEC61000-4-5input/output lines:±1 kVThe device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.IEC 60601 test levelFloors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.±2 kV power supply lines: 100 kHz repetitionfrequencyline(s) to line(s): ±1 kV 100 kHz repetitionfrequencyMains power quality should be that of a typical commercial or hospital environment.Mains power quality should be that of a typical commercial or hospital environment.Mains power quality should be that of a typical commercial or hospital environment.Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.0% UT ; 0.5 cycleAt 0°, 45°, 90°, 135°,180°,225°,270° and 315°0% UT ; 1 cycle and 70% UT ; 25/30 cyclesSingle phase: at 0°0% UT ;300 cycleTable 3Guidance and manufacturer’s declaration – electromagnetic immunityImmunity test Compliance levelIEC 60601 Test levelConducted RFIEC 61000-4-6 Radiated RF IEC 61000-4-310V/m, 80% Amat 1kHz150 kHz to80 MHz: 3 Vrms6Vrms (in ISM and amateur radio bands)80% Am at 1kHz Electromagnetic environment - guidanceNOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.aField strengths from fixed transmitters, such as base stations for radio (cellular / cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the device.Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3V/m.bThe device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.150 kHz to80 MHz: 3 Vrms6Vrms (in ISM and amateur radio bands)80% Am at 1kHz Portable and mobile RF communications equipment should be used no closer to any part of the device, including cables, than the recommended separation distance calculated from the equation appropriate for the frequency of the transmitter.Recommended separation distances:d=0.35 ;d=1.210V/m, 80% Amat 1kHz80 MHz to 800 MHz:d=1.2800 MHz to 2.7 GHz:d=2.3where, P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer, d is the recommended separation distance in meters (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, should be less than the compliance level in each frequency range.Interference may occur in the vicinity of equipment marked with the followingsymbol:PPPP
EMC GUIDANCE30 31EMC GUIDANCE 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.7 GHz Table 4Recommended separation distances between portable and mobile RF communications equipment and the device.Rated maximum outputpower of transmitter(W) Separation distance according to frequency of transmitter (m)0.010.11101000.12 0.120.381.23.8120.230.732.37.323=d =d 1.2 2.3=d0.371.23.8123.5The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmittters) and the device as recommended below, according to the maximum output power of the communications equipment.For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.PPP Table 5Guidance and manufacturer’s declaration - electromagnetic immunityTest Frequency (MHz)385 0.3 27The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device, should assure that it is used in such an environment.NOTE If necessary to achieve the IMMUNITY TEST LEVEL, the distance between the transmitting antenna and the ME EQUIPMENT or ME SYSTEM may be reduced to 1 m. The 1 m test distance is permitted by IEC 61000-4-3.Radiated RF IEC61000-4-3 (Test specifications for ENCLOSURE PORT IMMUNITY to RF wireless communications equipment) Band a)(MHz)Service a) Modulation b) Modulation b)(W)Distance (m)IMMUNITY TEST LEVEL (V/m)380-390 TETRA 400Pulse modulation b) 18Hz1.8450 380-390GMRS 460，FRS 460FM c) ± 5kHzdeviation 1kHzsine20.3 28710 704-787745780LTE Band13,17Pulse modulation b)217Hz0.2 0.3 9810870930800-960GSM 800/900,TETRA 800,iDEN 820,CDMA 850,LTE Band 5Pulse modulation b)18Hz20.3 281720184519701700-1990GSM 1800;CDMA 1900;GSM 1900;DECT;LTE Band 1,3,4,25; UMTSPulse modulation b)217Hz20.3 2820.3 282450 2400-2570Bluetooth,WLAN,802.11 b/g/n, RFID2450, LTEBand 7Pulse modulation b)217 Hz5240524057855100-5800WLAN802.11a/nPulsemodulation b)217 Hz0.2 0.3 9a) For some services, only the uplink frequencies are included.b) The carrier shall be modulated using a 50% duty cycle square wave signal.c) As an alternative to FM modulation, 50% pulse modulation at 18 Hz may be used because while it does not represent actual modulation, it would be worst case.The MANUFACTURER should consider reducing the minimum separation distance, based on RISK MANAGEMENT, and using higher IMMUNITY TEST LEVELS that are appropriate for the reduced minimum separation distance. Minimum separation distances for higher IMMUNITY TEST LEVELS shall be calculated using the following equation: E=Where P is the maximum power in W, d is the minimum separation distance in m, and E is the IMMUNITY TEST LEVEL in V/m.

Navigation menu