Tranwo Technology A7196 2.4GHz Digital Audio Video Module User Manual Go Link

Tranwo Technology Corp 2.4GHz Digital Audio Video Module Go Link

User Manual

Date: 2016/10/25 Preliminary data subjects to change without notice 1 A7196 2.4GHz Digital Audio Video Module A. Features Operating frequency range from 2400 to 2483.5 MHz Maximum data rate 6 Mbps Support 3-wire or 4-wire SPI. Modulation scheme : DSSS On chip regulator, input voltage range: 3 ~ 3.6V Transmission range: 250 m (Line of sight) Outline: 21.16x 18.36 x2.81 mm B. Applications Digital Baby Monitor Wireless Video Door phone Security Camera
Date: 2016/10/25 Preliminary data subjects to change without notice 2 A7196 2.4GHz Digital Audio Video Module C: Specification Parameter Min. Typ. Max. Unit Electrical Section Supply Voltage 3 3.3 3.6 V Supply current in TX mode TBD mA Supply current in RX mode TBD mA Crystal 24M Hz RF Section Modulation Mode FSK/GFSK Operating Frequency(Note1) 2400 ~ 2483.5 MHz Data Rate 6M bps Transmitter Section Transmission Power +15 dBm Power control range 16 dB Receiver Section Sensitivity -80 dBm Operation Operating Temperature -20 ~ +70 ℃ Storage Temperature -40 ~ +85 ℃ Note:1. 2.4GHz ISM Band
Date: 2016/10/25 Preliminary data subjects to change without notice 3 A7196 2.4GHz Digital Audio Video Module RF Front End Control: RF_TX_SW RF_RX_SW Operating Conditions 0 1 TX Active 1 0 RX Active Note: “1”denotes high voltage stste(>1.2V) “0” denotes low voltage stste(<0.3V)at Control Pins
Date: 2016/10/25 Preliminary data subjects to change without notice 4 A7196 2.4GHz Digital Audio Video Module Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Date: 2016/10/25 Preliminary data subjects to change without notice 5 A7196 2.4GHz Digital Audio Video Module This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna(required antenna: Max. gain 2dBi ,Dipole) 3) Module approval valid only when the module is installed in the tested host or compatible series of host As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: O6L-A7196”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu