Tranwo Technology IPCAM-RFDWM RF_Door/ Window Sensor / Door/ Window Sensor_RF User Manual 410 000089 00 QC

Tranwo Technology Corp RF_Door/ Window Sensor / Door/ Window Sensor_RF 410 000089 00 QC

Users Manual

2Less than 50cm1Step1: Battery On1. Remove the back cover.2. Install two AAA batteries. Step2: Sensor Pairing1. Turn on camera and launch “iSmart-CAM” APP. Go to “Camera Setting” and tap ”IoT Sensor Setting”.2. Tap the then hold the pairing button for 3 seconds within 5 seconds.3. The sensor type will be displayed after paring completed.4. Tap the “Door/Window Sensor” for detailed settings. Note: If pairing successfully, the LED will light up for 3 seconds. If failed, the LED will blink.1EN Pairing Button2. LED Light3. Magnetic Reed Switch1.123 Product Layout 1 Quick Setup 2RF_DWMRF_Door/ Window Sensor Installation GuideManuel de l'utilisateurGuía de instalaciónInstallationsanleitungGuida all'installazione1 Placement 41- Modulation: GFSK- Dimensions: 66x34x25mm, Magnet: 58x13x15mm- Weight: 32.5 g- Magnet Sensor Gap Activated: 10mm- Operating Distance: 30m* (indoor)- Power Supply: 3V (AAAx2)- Battery Life: 1 year* (Triggered twenty times a day)- Operating Temperature: 0℃ ~ 40℃ (32℉ ~ 104℉)*Actual operating distance and battery life may vary with the usage patterns and operating environment.- Frequency: 2.4G HzRF Specification 51 cm (max)3410-000089-0012. Name : Sensor Name3. : Search this sensor. If searched, the sensor LED will flash five times. 4. Alarm On/Off : “Alarm On ”will enable you to receive push message when Door/Window sensor event is triggered.5. : The camera will rotate to a preset position when “Alarm On” and Door/Window sensor event is triggered. Through live view window to position the camera and tap “Locate” to confirm.1. No. : Sensor Number. Tap it to select other sensor. (No. 0,1,2….) Sensor Setting312435FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for helpThis device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference,and (2) this device must accept any interference received, including interferencethat may cause undesired operation.Caution To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. FCC StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Caution To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

Navigation menu