Trilliant Networks GWPRO Wireless Mesh WAN Backhaul Node User Manual SkyGateway SkyExtender Installation and Setup

Trilliant Networks, Inc. Wireless Mesh WAN Backhaul Node SkyGateway SkyExtender Installation and Setup

UserManual.wiki >

Trilliant Networks >

GWPRO User Manual >

Contents

1. Manual
2. Setup and Installation

Manual

| iSkyPilot™ by Trilliant® Gateway ProInstallation and SetupPreliminary671-00XXX-01 Rev A Draft 1SP-5XXX

Contents | iiiContentsAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vAudience and Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viHow This Guide Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . viConventions Used in This Guide . . . . . . . . . . . . . . . . . . . . . . .viiChapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Solution Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Mesh Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2SkyPilot Gateway & SkyPilot Gateway Pro . . . . . . . . . . . . . . . . . 4SkyPilot Extender, Extender DualBand . . . . . . . . . . . . . . . . . . . 4SkyPilot Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Chapter 2 Your SkyPilot Gateway Pro Kit . . . . . . . . . . . . . . . . . . 7Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Required Tools and Supplies. . . . . . . . . . . . . . . . . . . . . . . . . . 9Chapter 3 Planning Your SkyPilot Network . . . . . . . . . . . . . . . 11Deployment Process Overview . . . . . . . . . . . . . . . . . . . . . . . 12Network Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Co-Located SkyPilot Gateway Pro Devices . . . . . . . . . . . . . . . . 16Chapter 4 Configuring the SkyPilot Gateway Pro. . . . . . . . . . . . 17Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Powering Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Configuring the SkyPilot Gateway Pro. . . . . . . . . . . . . . . . . . . 22Configuring Adjacent SkyPilot Gateway Pros . . . . . . . . . . . . . . 26Chapter 5 Installing the SkyPilot Gateway Pro . . . . . . . . . . . . . 27Install Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Chapter 6 Verifying Connectivity . . . . . . . . . . . . . . . . . . . . . . 33Confirming SkyPilot Gateway Pro Connectivity . . . . . . . . . . . . . 33Confirming SkyPilot Extender and SkyPilot Connector Connectivity 35Confirming SkyPilot Extender DualBand Access Point Connectivity 37Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Appendix A Grounding Guidelines . . . . . . . . . . . . . . . . . . . . . . 41General Grounding Strategy . . . . . . . . . . . . . . . . . . . . . . . . . 41Adding Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Grounding Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Appendix B FCC Statements . . . . . . . . . . . . . . . . . . . . . . . . . . 45FCC Class A Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45FCC Class B Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Maximum Permissible Exposure . . . . . . . . . . . . . . . . . . . . . . 46FCC 15.203 statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

iv | ContentsRegulatory Statements for Canada . . . . . . . . . . . . . . . . . . . . . 46Appendix C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .49Appendix D Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53RJ-45 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53DB-9 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

| vAbout This GuideThis guide explains how to install and set up a SkyPilot™ Gateway™ Pro device. It assumes administrator-level knowledge of IP networks and a familiarity with configuring wireless devices.Chapter HighlightsAudience and purposeHow this guide is organizedConventions used in this guide

vi | About This GuideAudience and PurposeThis guide provides directions for installing and setting up a SkyPilot Gateway Pro.This guide assumes administrator-level knowledge of IP networks and a familiarity with configuring wireless devices.How This Guide Is OrganizedThis guide is organized as follows:Chapter 1, “Introduction,” provides an overview of the SkyPilot solution, describes the SkyPilot devices, and then illustrates how they combine to form a mesh network.Chapter 2, “Your SkyPilot Gateway Pro Kit,” provides the information you need before you begin your installation.Chapter 3,“Planning Your SkyPilot Network,” provides an overview of network planning guidelines and proceduresChapter 4, “Configuring the SkyPilot Gateway Pro,” describes the process for bringing up a SkyPilot Gateway Pro unit for the first time.Chapter 5, “Installing the SkyPilot Gateway Pro,” explains how to mount the unit in the field.Chapter 6, “Verifying Connectivity,”describes the steps needed to verify proper operation of each device.Appendix A, “Grounding Guidelines,” provides direction on protecting your SkyPilot device with proper grounding and surge protection.Appendix B, “FCC Statements,” provides the FCC radio frequency interference statements for the SkyPilot Gateway Pro devices.Appendix C, “Specifications,” give the mechanical and electrical specifications of the SkyPilot Gateway Pro.Appendix D, “Pinouts,” provides pinouts for connectors and adapters to connect to the Ethernet interface port labeled “CPE” on the SkyPilot Gateway Pro power supply and the device’s serial interface.

Conventions Used in This Guide | viiConventions Used in This GuideThis section describes the text and syntax conventions used throughout this guide.Text ConventionsThis guide uses the following text conventions:Italic is used to introduce new terms.Bold is used to indicate what you click or type in a graphical user interface (for example, commands names or text being entered). In examples showing user interaction with the command-line interface, bold is used to indicate user input as opposed to command output.A monospace font is used for code elements (variable names, data values, function names, and so forth), command lines, scripts, and source code listings.Italic-monospace is used for replaceable elements and placeholders within code listings.Syntax ConventionsThis guide uses the following conventions when showing syntax:Angle brackets, “<“ and “>”, enclose mandatory elements. You must enter these elements. For example:ping <IP-address>Square brackets, “[“ and “]”, enclose optional elements. You can omit these elements. For example:show filter [filter-table-number]Square brackets are also used to show the current value of parameters in the output of some commands.A vertical bar, “|”, separates choices. For example:show bridge [cache | port]

viii | About This Guide

| 1IntroductionThis chapter provides an overview of the SkyPilot Networks solution, describes the SkyPilot devices, and then illustrates how they combine to form a mesh network.Chapter HighlightsSolution OverviewMesh NetworkSkyPilot Gateway and SkyPilot Gateway Pro1

2 | Chapter 1 IntroductionSolution OverviewA SkyPilot Network delivers a wireless, end-to-end broadband solution that seamlessly supports high-capacity, high-coverage mesh networks. Designed for managed-access networks and service providers, the SkyPilot network takes broadband wireless the “last mile” with a cost-effective, robust infrastructure solution.Based on a high-performance architecture that includes intelligent antenna arrays, the SkyPilot network delivers a dynamic broadband solution.SkyPilot wireless devices are simple to install and easily fit into any type of wireless environment—metropolitan, business, or home.The auto-discovery and rapid provisioning features of a SkyPilot wireless mesh network can greatly reduce deployment and maintenance costs. Multiple topology options and network scalability create intriguing options for rapidly expanding a metro Wi-Fi customer base.Mesh NetworkThe typical configuration for a SkyPilot network is a mesh topology, which uses SkyPilot Extenders to extend range and add network flexibility. In a mesh configuration, subscribers can either connect directly to the SkyPilot Gateway Pro or connect indirectly via SkyPilot Extenders (see Figure 1-1). In addition to adding range, a mesh network allows connections from locations where obstructions prevent line-of-sight access to a SkyPilot Gateway Pro.Mesh networks are ideal for dense subscriber environments, for filling in coverage “holes,” and for reaching subscribers in areas where RF communication is obstructed by hills, trees, buildings, or other obstacles.

Mesh Network | 3Figure 1-1. SkyPilot wireless mesh networkInternetSkyPilot ConnectorSkyPilot ConnectorSkyPilot Gateway ProSkyPilot ExtenderSkyPilot ExtenderSkyPilot ExtenderWi-Fi zoneSkyPilot Extenders increase thecoverage footprint by extending the wireless mesh network beyond the range of the SkyPilot Gateway Pro.SkyPilot Connectors link subscribersto the wireless mesh network viaan Ethernet port that allows connection from a PC or a localarea network.Adds a Wi-Fi access point providing802.11 wireless access to the meshnetwork in metropolitan “hot” zones.SkyPilot Extender Provides broadband Internet access via Wi-Fi and supports publicsafey applications such as video surveillance..SkyPilot Extender

4 | Chapter 1 IntroductionSkyPilot Gateway & SkyPilot Gateway ProThe SkyPilot Gateway and Gateway Pro operate as a base stations for a wireless mesh network. They provide an interface between the wired infrastructure and a wireless network of subscribers who enjoy secure, high-speed access to the Internet.A SkyPilot wireless network requires at least one SkyPilot Gateway or SkyPilot GatewayPro, for operation. If necessary, you can add additional SkyPilot Gateway Pros to increase network capacity or provide redundancy.A SkyPilot Gateway or Gateway Pro resides at a location with easy access to wired infrastructure—usually a POP (point of presence) or data center.The SkyPilot Gateway Pro uses an advanced, second-generation electronically steerable antenna to deliver higher overall throughput. In addition, it XXX...SkyPilot Extender, Extender DualBandSkyPilot Extenders and SkyPilot Extender DualBands provide a cost-effective way to extend range and balance network loads by operating as repeaters to extend the wireless range of a SkyPilot Gateway Pro (see Figure 1-1). You can add a SkyPilot Extender device to your network to expand your coverage footprint and provide redundancy through SkyPilot’s mesh networking features. SkyPilot Extender devices, including DualBands, can provide subscribers with a direct connection to the wireless network via the device’s Ethernet port.SkyPilot Extender DualBand is a dual-radio solution that combines SkyPilot’s long-range, high-capacity 5 GHz mesh backhaul with a high-powered 2.4 GHz 802.11b/g access point that allows service providers and municipalities to offer standard Wi-Fi services, for targeted hot zones or ubiquitous coverage patterns.For optimum performance, install the SkyPilot Extender in an elevated location such as a roof, tower, or utility pole.

SkyPilot Connector | 5SkyPilot ConnectorSkyPilot Connectors link your subscribers to the SkyPilot wireless network. An Ethernet port on the device allows a connection to a subscriber’s computer, or to a local area network (LAN) via a data switch or router. Designed for installation by the service provider, the SkyPilot Connector attaches to an external structure such as an eave, roof, or pole. The SkyPilot Connector DualBand offers the same features as a SkyPilot Connector, plus a Wi-Fi access point that enables service providers and municipalities to provide standard 802.11 wireless access, for targeted hot zones, or for dense coverage patterns.

6 | Chapter 1 Introduction

| 7Your SkyPilot Gateway Pro KitYour SkyPilot Gateway Pro kit provides the basic equipment you need to install the device and configure it for operation on a SkyPilot wireless mesh network. This chapter describes that equipment and lists additional items you should have on hand before starting installation.Chapter HighlightsKit ContentsRequired Tools and Supplies2

8 | Chapter 2 Your SkyPilot Gateway Pro KitKit ContentsThe contents of the SkyPilot Gateway Pro kit are listed below:SkyPilot Gateway Pro unitPower supply. This unit is both a power supply and a power injector. Your SkyPilot Gateway Pro is powered over Ethernet, and you may use either the included power supply or your own PoE PSE equipment. Note that the power supply is not outdoor-ratedl it should be mounted indoors or in a suitable enclosure.DB-9 to RJ-45 adapter. This can be used to adapt the cat-5 serial port cable to a DB-9 serial port.GPS antennaGPS antenna mounting bracketWeatherproof cable connector housingMounting hardware, consisting of:two sets of two-piece pole clampsdouble-hinged mounting bracketsingle-hinged mounting bracketNuts, bolts, and washers

Required Tools and Supplies | 9Figure 2-1. SkyPilot Gateway Pro (rear view)Required Tools and SuppliesBefore starting installation, you also need the following:For basic mounting:7/16" wrench9/16” wrenchPhillips screwdriverLoc-tite or other thread-locking compoundFor pole mounting:Magnetic levelSteel pole between 1 1/4" and 2 1/8" in diameterFor network cabling:Spool of CAT-5 shielded network cable, outdoor-rated.RJ-45 straight through cable for a serial connection to a console (standard CAT-5 patch cable will work)

10 | Chapter 2 Your SkyPilot Gateway Pro KitNOTE In theory, you should never need to service a unit once it is deployed. However, should you need to do so, access to the serial port may be required. Many installers find it prudent to run a serial cable from the SkyPilot to a location that gives easier access.Crossover cable (for connecting to a an access point, switch, or router)RJ-45 unshielded connectors (connectors without a protective plastic boot are preferred; they fit through the cable clamp more easily.)RJ-45 crimping toolOpen-end wrench, adjustable or 1-3/6” (30 mm)Surge protection device (strongly recommended)For configuration:Computer with a serial port, a terminal emulation program, a network interface card, and a Web browser. A laptop recommended for convenience.

| 11Planning Your SkyPilot NetworkThis chapter provides instructions for configuring the SkyPilot Gateway Pro and then performing the physical installation.Chapter HighlightsPlanning your installationGPS and the SkyPilot Gateway Pro3

12 | Chapter 3 Planning Your SkyPilot NetworkDeployment Process OverviewTable 3-1 summarizes the stages of SkyPilot network planning and deployment.Network PlanningIdentify Equipment LocationsDeployment of a SkyPilot network starts with a site survey to help you identify the devices you need and choose optimum locations for installation.Identifying locations for the SkyPilot Gateway Pro and SkyPilot Connectors is straightforward. For the SkyPilot Gateway Pro, location depends on proximity to existing network infrastructure and site elevation. SkyPilot Connectors are placed at subscriber sites—homes or offices.Table 3-1. Stages of deployment Stage DescriptionIdentify equipment locationsIdentify and prepare locations for installation.Choose an operating frequencyChoose a “clean” center frequency that permits interference-free operation of devices.Provision SkyPilot devices Choose a provisioning mode for the devices: manual or automatic.Provision the devices. (For automatic provisioning, install operating system and SkyPilot EMS software.)Install SkyPilot devices Install the devices, beginning with SkyPilot Gateway Pro devices and building out.Verify connectivity Confirm that the SkyPilot Gateway Pro is online.Confirm that installed SkyPilot Connectors and SkyPilot Extenders have established a link with the SkyPilot Gateway Pro.Review link characteristics and network performance.

14 | Chapter 3 Planning Your SkyPilot NetworkGPS and the SkyPilot Gateway ProThe SkyPilot Gateway Pro uses a GPS (Global Positioning System) signal for synchronization with other SkyPilot devices on the network. The strongest GPS signal is available outdoors, where the device has an unobstructed view of the sky. (For indoor installations, such as for configuration and testing, the optimum location is on a windowsill or other opening with access to the sky.) A separate GPS antenna is included with your SkyPilot Gateway Pro. It should be mounted above the SkyPilot Gateway Pro, where is has a clear view of the sky.Upon startup, a SkyPilot Gateway Pro searches for a GPS signal, and if the device can’t detect a signal, it will be unable to complete startup and won’t establish wireless connections with other devices. You can configure a SkyPilot Gateway Pro even if the device can’t detect a GPS signal. While the device is searching for the GPS signal, press the TILDE key (~) to bypass the search; the device will then proceed through the startup sequence.NOTE The GPS search should be bypassed only for device configuration, not for standard operation. Without a GPS signal, data will not be reliably transmitted between devices.The LEDs on the base of the device will confirm availability of a GPS signal. Guidelines for Adding SkyPilot ExtendersMultiple factors can affect wireless network performance—and dictate the need for SkyPilot Extenders.Physical distance—Are all your subscriber sites close enough to the SkyPilot Gateway Pro for radio communications? If a SkyPilot Gateway Pro is installed in a high location with a clear sight line to subscriber sites, it can maintain radio communications with SkyPilot Connectors or SkyPilot Extenders at greater distances.Elevation—There is a correlation between range and device elevation. By installing SkyPilot devices on raised locations, such as towers or tops of buildings, you can avoid RF obstructions that can occur at ground level, thereby extending the range at which the devices can operate normally.

Network Planning | 15You should install SkyPilot devices at similar elevation because large elevation differences may have an adverse impact on signal strength.Obstructions—An optimum link between a SkyPilot Gateway Pro and a SkyPilot Connector requires a clear line of sight. Obstructions, both artificial and natural, can reduce effective network range or block radio communications entirely.Type of SkyPilot Connector—Because it’s typically placed outside and at higher elevation than the indoor connector, the outdoor version of the SkyPilot Connector provides greater wireless range than the indoor version.If there are obstructions blocking subscriber access (as in Figure 3-1) or if there are subscriber sites beyond the distance that a wireless link can maintain, you need to add one or more SkyPilot Extenders to the network.Figure 3-1. Using a SkyPilot Extender for network extension behind an obstruction

16 | Chapter 3 Planning Your SkyPilot NetworkPreparing SkyPilot Extender SitesIf SkyPilot Extenders are required, perform a survey of possible sites before beginning installation. For a detailed discussion of site requirements, refer to SkyGateway/SkyExtender Installation and Setup.For optimum service, attach SkyPilot Extenders to elevated, fixed locations with easy and continuous access to power.Choose an Operating FrequencyAll the devices on a SkyPilot network operate on a single frequency. Before beginning the installation, visit the deployment area and identify an optimum operating frequency. Use a spectrum analyzer or other frequency-planning tool to identify the best available frequency for the SkyPilot wireless network—a “clean” center frequency that permits interference-free operation of devices.Co-Located SkyPilot Gateway Pro DevicesIf you put two of ‘em together, you.....

Provisioning | 17Configuring the SkyPilot Gateway ProThis chapter provides instructions for configuring the SkyPilot Gateway Pro and then performing the physical installation.You should test and configure you SkyPilot Gateway Pro on the bench before deploying it to the field. To do so, you will need to connect cables and the GPS antenna.Chapter HighlightsCablingPowering upConfiguring the SkyPilot Gateway ProAccessing the command-line interfaceProvisioningTo provision your SkyPilot Gateway Pro, you must:Choose a provisioning mode: automatic or manual. Prepare the network infrastructure. For automatic provisioning, you must install SkyPilot software on a supported operating system to create your Network Management System (NMS)4

18 | Chapter 4 Configuring the SkyPilot Gateway ProCablingEthernet cabling provides power and data connectivity for the SkyPilot Gateway Pro. Serial cabling provides connectivity for troubleshooting and local configuration. Figure 4-1. Cable Connections and Mounting HolesTo install cabling for Ethernet, and optionally serial connections:1Remove the access plate from the back of the unit.2Connect the Ethernet cable.aUnscrew the black cable clamp and remove the grey rubber gasket.bThread your Ethernet cable through the black plastic cap and then the grey gasket. In most cases, you can fit the RJ-45 plug through the gasket, or you can thread the cable through first and them crimp on a connector.Ethernet JackSerial PortCable ClampSerial Port Access HoleUpper Mount HolesLower Mount HolesGPS Mount HolesGround LugGPS SMA Connector

Cabling | 19cThread the Ethernet cable through the connector body and plug it into the RJ-45 receptacle on the circuit board.dMakes sure there is a little slack in the cable inside the unit, to act as a strain relief.eInsert the grey gasket back into the connector, and then tighten the cap until the cable is securely held. 3Connect the serial cable. This is done in the same manner as the Ethernet cable. You must first remove the plug and installed the supplied cable clamp. The plug unthreads; use a large flat-blade screwdriver or a coin.4Re-attach the cover.5Use cable ties or Velcro wraps to secure all the cabling against strain.Figure 4-2. Exploded View of Cable Clamp AssemblyRubber PlugNutCat 5 Cable

20 | Chapter 4 Configuring the SkyPilot Gateway ProGPS Antenna1Attach the GPS antenna bracket to the top of the unit, on the back, using two small Phillips screws. This is shown in Figure 4-3.2Connect the GPS antenna cable to the SMA connector on the unit bottom.3The GPS antenna is magnetic, and will stick to the mounting bracket.4Temporarily place the GPS antenna where it can pick up a GPS signal. You can use a hand-held GPS device, such as an iPhone, to determine if there is adequate signal strength in your location.Figure 4-3. GPS bracket

Powering Up | 21Powering Up1Connect a power cord to the power supply, and plug it in.2Connect the Ethernet cable from the SkyPilot Gateway Pro to the port labeled “Output” on the power supply. 3Connect an Ethernet cable from the port labeled “Input” to your network.Monitoring the Power-On SequenceWhen the SkyPilot Gateway Pro is powered up, it starts a power-on sequence. You can monitor itby observing the pair of LED lights on the back of the device. The power-on sequence may take up to 15 minutes, depending on how quickly the device can acquire a GPS signal.NOTE The SkyPilot Gateway Pro must have access to a GPS signal to complete its power-on sequence and start making wireless network connections. Depending on your SkyPilot network configuration, the device may be unable to connect to the network until the device has been configured. Table 4-1 provides detailed descriptions of device states indicated by the LEDs..Table 4-1. SkyPilot Gateway Pro LED Status Lights Device state LED 1 (left) LED 2 (right)Startup in progress Slow staggered blinking of both LEDsStartup failure Off OnInitializing image, acquiring GPS signal Blinks 4 times; repeats Blinks 4 times; repeats Initialization failure Fast, synchronized blinking of both LEDsSuccessful initialization, but authorization failureGreen OffSuccessful initialization, but no links foundGreen ???Connected Green Blue

22 | Chapter 4 Configuring the SkyPilot Gateway ProConfiguring the SkyPilot Gateway ProTo operate on the wireless mesh network, the SkyPilot Gateway Pro requires a network configuration. A SkyPilot Gateway Pro will not transmit a wireless signal until it is configured, and it will not be able to connect to other network devices without a configuration.SkyPilot offers two modes for provisioning devices with a configuration:Automatic—Requires the use of SkyPilot EMS software to create configurations that an unattended central server can distribute to devices on the wireless mesh network. Although automatic provisioning requires more initial setup time than manual provisioning, it greatly simplifies the administration of a growing network.Detailed procedures for using EMS software are provided in SkyPilot Network Administration, available from the SkyPilot website at www.skypilot.com/support/. Manual—Manual provisioning permits the configuration of only a single device at a time, creating the minimum settings required for a wireless link and storing them in the device’s flash (nonvolatile) memory. Manual provisioning is a logical choice if you’re installing a test network or rolling out a small-scale installation that isn’t expected to expand.For more information about provisioning modes, refer to Getting Started with the SkyPilot Network, available from the SkyPilot website at www.skypilot.com/support/.Accessing the Command-Line InterfaceSkyPilot devices include a command-line interface which you can use for manual provisioning and troubleshooting.You can connect to a device and access its command-line interface through Telnet over an Ethernet connection or via a terminal session from a console connected to the device’s RJ-45 serial port. The default IP address is 192.168.0.2After logging in (user: admin; password: public), you can enter commands at the command prompt.

Configuring the SkyPilot Gateway Pro | 23For detailed access instructions for the command-line interface, refer to the SkyPilot Command-Line Interface Reference.Manually Provisioning DevicesManual provisioning stores settings in the device’s flash memory, where they remain available for recall when the device starts up.NOTE If you’re installing a device in a location that poses difficulties, consider delaying the final mounting until you can confirm that provisioning was successful.Table 4-2 summarizes the steps required to manually provision a device.Table 4-2. Manually Provisioning a Device (Page 1 of 2)Step Refer to1Decide whether to provision the device using the command-line interface or the Web interface.(For DualBand/ access points, you must use the Web interface.)”Choosing a Manual Provisioning Method” in SkyPilot Network Administration2Prepare the device for installation by installing the necessary cabling, attaching antennas (for DualBands), and readying the device for service.Do not install the device yet.The appropriate installation manual:SkyGateway/SkyExtender Installation and SetupSkyConnector Indoor InstallationSkyConnector Outdoor Installation3Power on the device.

24 | Chapter 4 Configuring the SkyPilot Gateway Pro4Connect a computer to the device and access the command-line interface or the Web interface.(For DualBands, this step refers to the SkyPilot Extender portion of the device.)The appropriate interface reference manual:SkyPilot Command-Line Interface ReferenceSkyPilot Web Interface Reference5Provision the device.(For DualBands, this step refers to the SkyPilot Extender portion of the device.)Either of the following provisioning tool references, making sure to set at least the minimum provisioning parameters (refer to “Required Provisioning Parameters” and in SkyPilot Network Administration):SkyPilot Command-Line Interface ReferenceSkyPilot Web Interface Reference6For DualBands, reboot the device, connect a computer to the device’s 2.4 GHz access point, and provision the access point.SkyPilot Web Interface Reference7Power off the device. 8Complete the installation. The appropriate installation manual:SkyGateway/SkyExtender Installation and SetupSkyConnector Indoor InstallationSkyConnector Outdoor Installation9Power on the device. Table 4-2. Manually Provisioning a Device (Page 2 of 2)Step Refer to

Configuring the SkyPilot Gateway Pro | 25Automatically Provisioning All Network DevicesTable 4-3 summarizes the steps required to automatically provision all devices on a network. Although it’s possible to provision SkyPilot devices in any order, by following this sequence you can ensure that devices are able to form links as soon as they come online.Table 4-3. Automatically Provisioning All Network Devices (Page 1 of 2)Step Refer to1For new SkyPilot network deployments, custom-install the operating system software on the SkyPilot EMS server.The appropriate installation manual:SkyPilot OS Installation: Red Hat Linux 9.0SkyPilot OS Installation: Fedora Core 2 and 4SkyPilot OS Installation: Red Hat Enterprise Linux ES 3 and 42For new SkyPilot network deployments, install the server component of SkyPilot EMS, and then install the client component of SkyPilot EMS on any appropriate computer.SkyPilot EMS Installation3For new SkyPilot Gateway Pros, set up the DHCP server and, if the provisioning server is behind a firewall, specify ports for data traffic between the server and SkyPilot devices.”Adding Devices to the DHCP Configuration File” in SkyPilot Network Administration4Provision the SkyPilot Gateway Pro(s).The following automatic provisioning topics in SkyPilot Network Administration:“Provisioning a Device”“Starting SkyProvision”“SkyProvision Display Pane””Searching for Configured Devices”

26 | Chapter 4 Configuring the SkyPilot Gateway ProConfiguring Adjacent SkyPilot Gateway Prosis quite tricky....5For new SkyPilot Gateway Pros, complete the installation and power it on.SkyGateway/SkyExtender Installation and Setup6(Optional) Log in to the SkyPilot Gateway Pro and configure the management VLAN.”The SkyPilot EMS Interface” in SkyPilot Network Administration7Provision the SkyPilot Extender(s).The following automatic provisioning topics in SkyPilot Network Administration:“Provisioning a Device”“Starting SkyProvision”“SkyProvision Display Pane””Searching for Configured Devices”8For DualBands, provision the access point(s).For information about access point settings, refer to SkyPilot Network Administration. For configuration procedures, refer to the SkyPilot Web Interface Reference9For new SkyPilot Extenders, install the device and power it on.SkyGateway/SkyExtender Installation and Setup10 Provision the SkyPilot Connector(s).Same as for step 7.11 For new SkyPilot Connectors, install the device and power it on.The appropriate installation manual:SkyConnector Indoor InstallationSkyConnector Outdoor InstallationTable 4-3. Automatically Provisioning All Network Devices (Page 2 of 2)Step Refer to

Install Devices | 27Installing the SkyPilot Gateway ProThis chapter provides instructions for configuring the SkyPilot Gateway Pro and then performing the physical installation.Install DevicesYou can ensure optimum operation—and reduce administrative overhead—by installing your network devices in this order: SkyPilot Network Management SystemSkyPilot Gateway ProSkyPilot Extenders (optional)SkyPilot Connectors.You install the SkyPilot Gateway Pro first because, as the base station of the SkyPilot wireless network, it must be present in order for other devices to establish network links. When provisioned and powered on, the SkyPilot Gateway Pro immediately starts transmitting hello beacons that SkyPilot Extenders and Sky Connectors use to form links.After installing the SkyPilot Gateway Pro, you add SkyPilot Extenders (if required) and then SkyPilot Connectors. Upon powering on, each device responds to the base station’s hello beacon and starts forming links with the SkyPilot Gateway Pro. Each device attempts to establish as many links as possible before choosing an optimum path.After establishing network links, SkyPilot Extenders on your network also begin transmitting hello beacons, extending the range of beacons available to other devices. (SkyPilot Connectors do not transmit hello beacons.)5

28 | 5 Installing the SkyPilot Gateway ProMountingThe SkyPilot Gateway Pro uses two hinged mounting brackets to allow it to be tilted up or down slightly, as needed.Figure 5-1. Mounted SkyPilot Gateway Pro. To mount the SkyPilot Gateway Pro:IMPORTANTIt is the installer’s responsibility to verify that the support pole and its installation method are of sufficient strength to withstand onsite weather conditions. (The supplied mounting bracket and screws are certified to withstand a 150 mph wind force.)1Attach one of the pole-clamp assemblies to the pole at the height you want for the top of the unit. Make sure the threaded holes are facing up. Use the long bolts in the kit.

Mounting | 29Figure 5-2. Pole Clamps: Top View at Left; Bottom View at Right2Attach the second pole-clamp assembly to the pole, about nine inches lower than the first. Again, make sure the threaded holes are facing up.Figure 5-3. Pole Clamps Attached to Pole3Attach the hinged brackets to the SkyPilot Gateway Pro using the supplied 1/4-28 UNC bolts. These have hex heads. Do not use the Phillips-head screws. Use thread-locking compound.

30 | 5 Installing the SkyPilot Gateway ProThe brackets should be attached so that the body of the bracket is below the mounting holes. This, in turn, will orient the hook-tab, which is at the other end of the bracket, down.IMPORTANTThe double-hinged mounting bracket and the single-hinged bracket , together, allow you to tilt the unit. If you need to tilt it down, use the double-hinged bracket on top. If you need to tilt it up, use the double-hinged bracket on the bottom.IMPORTANTThe holes in the unit are fine-thread. DO NOT use 1/4-20 UNC (coarse thread) hardware in these holes.IMPORTANTThe SkyPilot Gateway Pro case is aluminum. Do no over-torque the mounting bolts.NOTE Your SkyPilot Gateway Pro can be wall-mounted. You will need lag bolts or other fasteners suitable for attaching to the wall. Use them to attach one-half of the pole clamp to the wall, then hang the SkyPilot Gateway Pro as described below.Figure 5-4. SkyPilot Gateway Pro with Mounting Brackets Attached1/4-28 hex-head boltsDouble-hinge bracketSingle-hinge bracketTabGPS antenna on bracket

Mounting | 314The SkyPilot Gateway Pro can now be hung from the pole clamps. The tabs fit into recesses in the pole clamps. Use the 1/4-20 Phillips screws to secure the brackets to the clamps.Figure 5-5. SkyPilot Pro-Top View - Showing Tabs & Screws5Adjust the angle of the unit, and then tighten the hinge bolts.Tab1/4-20 Phillips-head screwsHinge bolts

32 | 5 Installing the SkyPilot Gateway Pro

Confirming SkyPilot Gateway Pro Connectivity | 33Verifying ConnectivityAfter provisioning and installing your SkyPilot devices, you should perform the procedures in the following sections to confirm that the devices are properly connected to the network.Confirming SkyPilot Gateway Pro ConnectivityThere are two ways to confirm SkyPilot Gateway Pro connectivity:Check the LED status lights on the SkyPilot Gateway Pro to verify that the device is fully online.See Table 6-1for a summary of what the LED status lights mean. For a detailed description of the status lights, refer to SkyGateway/SkyExtender Installation and Setup.Table 6-1. SkyPilot Gateway Pro LED status lightsDevice state Link LED Activity LEDStartup in progress Slow staggered blinking of both LEDsStartup failure Off OnInitializing image (and acquiring GPS signal)Blinks 4 times; repeats cycleBlinks 4 times; repeats cycleInitialization failure Fast, synchronized blinking of both LEDsSuccessful initialization, but authorization failureOn OffConnected On On6

34 | 6 Verifying ConnectivityFrom the command line, use the ping command to verify that you can reach the device’s default gatewayFor example:> ping 192.168.5.1PING 192.168.5.1: 56 data bytes64 bytes from 192.168.5.1: icmp_seq=0. time=11. ms64 bytes from 192.168.5.1: icmp_seq=1. time=12. ms64 bytes from 192.168.5.1: icmp_seq=2. time=12. ms ----192.168.5.1 PING Statistics---- 3 packets transmitted, 3 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/16/32

Confirming SkyPilot Extender and SkyPilot Connector Connectivity | 35Confirming SkyPilot Extender and SkyPilot Connector ConnectivityThere are four ways to confirm SkyPilot Extender and SkyPilot Connector connectivity. You can use any method at any time.Check the LED status lights on the device to verify that the device is fully online.For a summary of what the LED status lights mean, see Table 6-2 (for SkyPilot Extenders) or Table 6-3 (for SkyPilot Connectors). For a detailed description of the status lights, refer to the installation guide for the device.Table 6-2. SkyPilot Extender/DualBand LED status lights Device state Link LED Activity LEDStartup in progress Slow staggered blinking of both LEDsStartup failure Off OnInitializing image (and acquiring GPS signal)Blinks 4 times; repeats cycleBlinks 4 times; repeats cycleInitialization failure Fast, synchronized blinking of both LEDsSuccessful initialization, but can’t locate helloOn OffSuccessful initialization; heard hello on antennas with power levels in the proper RSSI rangeOff Blink (modulation rate-based)Successful initialization; link is not optimized, or is in pre-authorizationSlow blink Blink (modulation rate-based)Successful initialization; link is in standby state on antenna and modulation rateFast blink Blink (modulation rate-based)Connected On On

36 | 6 Verifying ConnectivityFrom the command line, use the show link command to confirm that an active link exists.The device is online if the output displays an act path (active path) link state.For example:Use the traceroute command to confirm that you can send and receive data across the wireless network.The traceroute command performs a SkyPilot protocol trace that shows the path to the SkyPilot Gateway Pro. Entering the traceroute command Table 6-3. SkyPilot Connector LED status lights LED LED state Device stateLan Link Steady illumination SkyPilot Connector is connected to another device via its Ethernet portLAN Act Blinking Device is transmitting or receiving data via its Ethernet portWAN Link Blinking (fast blink when device is in standby mode)Device is attempting to establish an authorized connection on the wireless networkSteady illumination Device is connected to the wireless networkWAN Act None Device cannot detect a wireless networkBlinking Device is within the coverage area of a wireless network. Blink indicates signal strength:Fast (8x per second): excellentMedium (4x per second): goodSlow (<1x per second): poorNode Id LType NType State RSSI LTxMod RTxMod LAnt RAnt----------------- ----- ----- --------- ---- ------ ------ ---- ---00:0a:db:00:00:43 data ext act path 39 48 36 2 4

Confirming SkyPilot Extender DualBand Access Point Connectivity | 37without arguments returns a path that the device identifies as its exit from the network.For example:> traceroutetraceroute to 00:0a:db:00:00:a6>> 1 (48) --> 00:00:43 --> (36)2 (36) --> 00:00:a6 --> (36)Use the ping command to verify that you can reach the device’s default gateway.For example:> ping 192.168.5.1PING 192.168.5.1: 56 data bytes64 bytes from 192.168.5.1: icmp_seq=0. time=11. ms64 bytes from 192.168.5.1: icmp_seq=1. time=12. ms64 bytes from 192.168.5.1: icmp_seq=2. time=12. ms ----192.168.5.1 PINGStatistics---- 3 packets transmitted, 3 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/16/32Confirming SkyPilot Extender DualBand Access Point ConnectivityThere are four ways to confirm SkyPilot Extender DualBand access point connectivity:Use the ping command to verify that the access point is up and running—for example, ping 192.168.0.3.For SkyPilot firmware versions 1.2p3 and later, use the show version ap command to verify the firmware version and, indirectly, that proper heartbeats are being sent from the PePLink Linux access point.From the command line, enable debugging (using the debug on command) and use the set log apwatchdog 3 command to display successful or failed heartbeat updates, reboot notices, factory resets, and so on.Using an 802.11b/g wireless card, connect to the default SSID, a string representation of the SkyPilot Extender’s MAC address with the WPA passphrase publicpublic.

38 | 6 Verifying ConnectivityOnce connected, use the ping command to verify that you can reach both the SkyPilot Extender and the access point. For example:> ping 192.168.0.3PING 192.168.5.1: 56 data bytes64 bytes from 192.168.0.3: icmp_seq=0. time=11. ms64 bytes from 192.168.0.3: icmp_seq=1. time=12. ms64 bytes from 192.168.0.3: icmp_seq=2. time=12. ms ----192.168.5.1 PINGStatistics---- 3 packets transmitted, 3 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/16/32> ping 192.168.0.2PING 192.168.5.1: 56 data bytes64 bytes from 192.168.0.2: icmp_seq=0. time=11. ms64 bytes from 192.168.0.2: icmp_seq=1. time=12. ms64 bytes from 192.168.0.2: icmp_seq=2. time=12. ms ----192.168.5.1 PINGStatistics---- 3 packets transmitted, 3 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/16/32

Troubleshooting | 39TroubleshootingAfter making an Ethernet or serial connection to the SkyPilot Gateway Pro, you can manage and troubleshoot the device using a wide range of commands available through the command-line interface.For detailed troubleshooting procedures, refer to the “Troubleshooting” section in SkyPilot Network Administration. There you’ll find troubleshooting procedures for:Power-on problemsEthernet connectivity problemsIP connectivity problemsSkyPilot Gateway Pro Transmission problemsLink failure problems

40 | 6 Verifying Connectivity

Grounding Guidelines | 41Grounding GuidelinesThis appendix provides some guidelines for properly grounding the SkyPilot Gateway Pro. Proper grounding protects both your SkyPilot device and equipment connected to it. For the surge protection circuitry built into the SkyPilot equipment to be effective, proper grounding of the unit is necessary. This is especially true if you’re installing devices on tall structures, or in areas subject to lightning.NOTE The techniques described in this appendix are intended as general guidelines only and do not constitute a comprehensive guide covering all installation scenarios. For maximum protection, contact a qualified installation specialist who is familiar with your operating environments. If lightning is a threat in your area, consider a consultation with a lightning and transient protection specialist.General Grounding StrategyTo ensure optimum reliability, properly ground the metal base of the SkyPilot device. The most efficient way to ground the device is to use an 8 GA or larger wire to connect it to a ground point on the mounting structure or tower.The three most common ground points are:A cold-water pipe. Make sure it is well-connected to earth.The primary grounding point of the AC electrical system of the building.A 10-foot or longer copper-clad ground rod driven into the earth. For a tower with multiple legs, you need one ground rod per leg and a ground wire loop connecting each of the rods; see Figure 12.A

42 | Appendix A Grounding GuidelinesFigure 12. Ground wire loopMaking Connections “Gas-Tight”Regardless of the grounding point you use, make sure the connections are “gas-tight”—capable of retaining low resistance and integrity over time and with exposure to the elements.Use of an antioxide compound and proper sealing is essential. For protection against corrosion, wrap all connections with Scotch® 130C tape. Checking Cold-Water Pipe IntegrityIf you’re using a cold-water pipe for grounding, verify the integrity of the ground. In some cases, sections of metal cold-water pipes may have been repaired or extended with PVC material. PVC material or a dielectric union will render a cold-water pipe ground unacceptable for grounding. A

Adding Surge Protection | 43Measuring ResistanceVerify that there is no more than 5 ohms of resistance between any two ground points in the entire system. Also make sure that all ground points on a structure are tied together. For example, if you use a ground rod and a cold-water pipe as grounding points at different locations on the same structure, you must tie them together.Adding Surge ProtectionIf you’re installing a SkyPilot device in an area that’s subject to lightning storms, SkyPilot recommends installing a surge protection device (SPD) at both ends of the Ethernet cable—one at the SkyPilot device and one at the point of entry to a building or enclosure. SkyPilot offers SPDs with bracket and cabling designed for use with SkyPilot equipment. For more information, visit SkyPilot customer support at www.skypilot.com/support/ to view accessory guides for SkyPilot-branded surge protection solution. (You may also purchase SPDs from third-party vendors.)Grounding ChecklistWhen grounding a SkyPilot device, use the following checklist to confirm that your installation is adequately protected from power surges and lightning.Connect a ground wire from the SkyPilot device to a ground system on the building or tower.Use shielded CAT5 cabling and connect the drain wire of the shield to ground at the SkyPilot device. (Leave the other end of the drain wire unconnected.)Use the proper size down lead to connect a SkyPilot device on a roof or tower to the ground system of indoor equipment. Verify that all points of the ground system are tied together with less than 5 ohms resistance between any two points.A

44 | Appendix A Grounding GuidelinesRun the CAT5 cable inside the tower structure, tying the cable to the tower leg at every 4 feet of length. For increased protection, run the CAT5 cable through metallic conduit installed on the tower.Bleed off any static charge by installing a streamer-delaying, static-dissipation array above the SkyPilot device.Install all lightning and surge protection devices in accordance with UL 96A installation requirements for lightning protection systems and the NFPA 780 standard for lightning protection.A

Specifications | 49SpecificationsThis appendix provides technical specifications for the SkyPilot Gateway Pro (Table C-1),Table C-1. SkyPilot Gateway Pro Specifications (Page 1 of 3)Wireless SpecificationsFrequency bands 5.150–5.450 GHz5.450–5.725 GHz5.725–5.850 GHzEIRP 44.5 dBm/28.2W peak, 36 dBm/4W average, 33 dBm/2W average, 30 dBm/1W average, or 36 dBm/4W peak (EIRP selected for country-specific regulations)Media access Time Division Duplex (TDD)Modulation technique OFDM with adaptive modulationModulation rates 6–54 MbpsThroughput UDP: Up to 20 MbpsTCP: Up to 10.5 MbpsLatency 10–12 ms round trip per hopAntennas Electronically-steered antenna, 180-degree coverageChannel width 20 MHzChannel resolution 5 MHz frequency controlReceive sensitivity -90 dBm at 6 Mbps modulationConnectivity SkyPilot Gateway Pro connects with: SkyPilot Extenders, SkyPilot Extender DualBandsSkyPilot Connectors.Authentication MD5-based certificatesEncryption 128-bit AES on all wireless linksC

50 | Appendix C SpecificationsProduct Specifications Connectors RJ-45: Ethernet connection (10/100Base-T) and power (Power over Ethernet)RJ-45: RS-232 serial for local managementMounting Tower, utility pole, building, or other infrastructure, outside pole diameter up to 2.5". Wall mount possible.Range Up to 10 miles (16 km)LEDs Wireless activity, wireless linkDimensions 17" (43 cm) H x 11.6" (29.5 cm) wide x 5.5” (14 cm) thickWeight 11 pounds (5 kg), basic unit17 pounds (7.7 kg) with standard mounting hardwareOperating temperature -40° to 131° F (-40° to 55° C)Wind loading Up to 150 mph (240 km/h)Enclosure/humidity NEMA-4XExternal PoE PSE Power 110–230 VAC, 50–60 Hz input, 16 watts maximumCertifications FCC Part 15, FCC 47 CFR Part 15, Class B USA; compliance with UL safety standards, CE, C-Tick, IC RSS210 Issue 5EMI and susceptibility FCC Part 15.107 and 15.109Warranty One-year limited warranty on hardware and softwareSecurity Authentication MD5-based certificatesEncryption AESFiltering Based on protocol type, IP port ID, and configurable IP address listNetwork management Command-line interface Console via RS-232 serial port or SSHNMS Integration SNMP v2c Table C-1. SkyPilot Gateway Pro Specifications (Page 2 of 3)

Specifications | 51GUI configuration SkyProvision™ software and Web interfaceGUI EMS SkyPilot EMS™ softwareIP address DHCP or static. 192.168.02. defaultFirmware Multiple versions of firmware stored in nonvolatile memory; updated via FTPConfiguration file XML over HTTPQoS (Quality of Service)Prioritization 802.1p-based; based on protocol type, IP address, port ID, and configurable IP address listTraffic shaping Per-device rate limits upstream and downstreamMonitoring and MIB supportSupported MIBs MIB-II (RFC 1213); EtherLike (RFC 2665); Bridge (RFC 1493); SkyPilot private MIBLocal management RS-232 Serial Console PortRemote management Command-line interface via Telnet, SNMP 2c, Web interfaceTopology Configurations Mesh, point-to-multipoint, point-to-pointTable C-1. SkyPilot Gateway Pro Specifications (Page 3 of 3)

52 | Appendix C Specifications

Pinouts | 53PinoutsThis appendix provides pinouts for connectors and adapters to connect to the Ethernet interface port labeled “CPE” on the SkyPilot Gateway Pro power supply and the device’s serial interface.RJ-45 PinsTable D-1 lists the RJ-45 pin assignments.Table D-1. RJ-45 Pin Assignments Pin Assignment1 Ethernet2 Ethernet3 Ethernet4 Power5 Power6 Ethernet7 Power8 PowerD

54 | Appendix D PinoutsDB-9 AdapterTable D-2 lists connecting pins between the SkyPilot Gateway Pro “CPE” port (RJ-45 connector) and a standard computer DB-9 serial port.The following figures show the connection between the SkyPilot Gateway Pro “CPE” port and a standard computer DB-9 serial port, the DB-9 pinouts, and the cable-pin correspondence.Figure D-1. RJ-45 to DB-9 physical connectorsFigure D-2. DB-9 pinsTable D-2. RJ-45 Pin Assignments SkyPilot Gateway/Extender“CPE” portComputer serial portSignal Pin Pin SignalTxD 3 2 RxDGND 4 5 GNDRxD 6 3 TxD

DB-9 Adapter | 55If you’re using a straight through cable, the connection can be visualized as shown in Figure D-3.Figure D-3. Straight through cablingAlthough there is no official standard, the connector wire colors typically are as described in Table D-3.Table D-3. Typical RJ-45 DB-9 Wire Colors Color RJ-45 pin DB-9 pinBlack 3 2Yellow 6 3Red 4 5

27 | Regulatory Information Regulatory information Federal Communications Commission (FCC) compliance notices This section includes the following FCC statements for the SP-5200-A and related SkyPilot by Trilliant products: • FCC ID: RV7-GWPRO • Class A Interference Statement • RF Radiation Exposure and Hazard Warning • Non-Modification Statement • Deployment Statement Class A Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure & Hazard Statement To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Non-Modification Statement Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the SP-5200-A and related SkyPilot by Trilliant products and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Deployment Statement This product is certified for indoor deployment only in the 5150 – 5250 MHz band. Do not install or use this product outdoors in that frequency band in the United States. Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands The SP-5200-A has been prohibited from operating in the 5600 to 5650 MHz frequency band for the US and Canada in order to comply with the DFS requirements as outlined in the FCC Part 15, Subpart E rules.

29 | Regulatory Information Canadian IC Statements IC: 6028A-GWPRO This device complies with ICES-003 and RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme aux normes NMB003 et CNR-210 d’Industrie Canada. 1. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 2. il ne doit pas produire de brouillage et l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. RF Radiation Exposure & Hazard Statement To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Exposition aux radiations RF & Mention de danger Pour assurer la conformité avec les exigences RSS-102 d'exposition aux RF (Radio Fréquences), cet appareil doit être installé dans un endroit ou l'antenne de l'appareil sera située à une distance de plus de 20 cm (8 po) de toutes personnes. L’utilisation d'antennes à gain plus élevé et les types d'antennes qui ne sont pas couverts en vertu de la certification IC de ce produit n'est pas autorisée. Les installateurs de la radio et les utilisateurs du produit final doivent se conformer aux instructions d'installation fournies dans ce manuel. Cet émetteur ne doit pas être co-implanté ou exploité en conjonction avec toute autre antenne ou transmetteur. Deployment Statement This product is certified for indoor deployment only in the 5150 – 5250 MHz band. Do not install or use this product outdoors in that frequency band in Canada. Déclaration de déploiement Ce produit est certifié pour le déploiement à l'intérieur tout en rencontrant les limites de cette bande de fréquences: 5150 - 5250 MHz. Ne pas installer ou utiliser ce produit à l'extérieur au Canada, si cette bande de fréquences ne peut ne peut être rencontrée.

29 | Regulatory Information SAFETY INFORMATION Hazard Warning! High Voltage. This situation or condition can cause injury due to electric shock. Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem Produkt angebracht oder in der Dokumentation enthalten sind. Warning! Read and follow all warning notices and instructions marked on the product or included in the documentation. Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem Produkt angebracht oder in der Dokumentation enthalten sind. Warning! Only use attachments and accessories specified and/or sold by the manufacturer. Warnung! Verwenden Sie nur Zusatzgeräte und Zubehör angegeben und / oder verkauft wurde durch den Hersteller. Warning! Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped. Warnung! Das Gerät sollte nur von qualifizierten Fachkräften gewartet werden. Eine Wartung ist fällig, wenn das Gerät in irgendeiner Weise beschädigt wurde, wie bei beschädigtem Netzkabel oder Netzstecker, falls Flüssigkeiten oder Objekte in das Gerät gelangen, das Gerät Regen oder Feuchtigkeit ausgesetzt wurde, nicht ordnungsgemäß funktioniert oder fallen gelassen wurde. Warning! Do not open the chassis. There are no user-serviceable parts inside. Opening the chassis will void the warranty unless performed by an Trilliant service center or licensed facility. Warnung! Öffnen Sie das Gehäuse nicht. Keine der Geräteteile können vom Benutzer gewartet werden. Durch das Öffnen des Gehäuses wird die Garantie hinfällig, es sei denn, solche Wartungsarbeiten werden in einem Trilliant-Service-Center oder einem lizenzierten Betrieb vorgenommen.

Navigation menu