Trilliant Networks OSDI4W1 IEEE 802.15.4 Transceiver Module User Manual
Trilliant Networks IEEE 802.15.4 Transceiver Module
Contents
- 1. User Manual
- 2. Usermanual
- 3. user manual
User Manual
DT‐0237Apage1of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Hardware User Guide Overview for Open Smart Device
Interface (OSDI) SecureMesh™ Module
Models:
OSDI-4000-1D
OSDI-4000-1A
PRINTEDVERSIONSOFTHISDOCUMENTAREUNCONTROLLED
Distributedunderlegalcommercialagreement
DOCUMENT RELEASE/APPROVALS
document # DT-0237A
current revision 1.0
approvals name title date
DT‐0237Apage2of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
LEGAL NOTICES
THIS DOCUMENT CONTAINS SENSITIVE PROPRIETARY AND CONFIDENTIAL INFORMATION OWNED
BY TRILLIANT NETWORKS. THIS DOCUMENT HAS BEEN PROVIDED TO YOUR COMPANY THROUGH
A PREVIOUSLY EXECUTED OSDI MODULE DESIGN LICENSE AGREEMENT AND MAY NOT BE
DISTRIBUTED TO ANY OTHER 3RD PARTY, IN ANY FORM OR PORTION, WITHOUT TRILLIANT’S
EXPRESSED WRITTEN PERMISSION.
LICENSEE ACKNOWLEDGES THAT THE OSDI MODULE DOCUMENTATION PACKAGE AND TOOLS
ARE LICENSED TO IT ON AN "AS IS" BASIS. TRILLIANT MAKES NO OTHER REPRESENTATIONS
AND EXTENDS NO OTHER WARRANTIES OR CONDITIONS OF ANY KIND, EXPRESS, IMPLIED OR
STATUTORY INCLUDING WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR USE. EXCEPT AS OTHERWISE EXPRESSLY SET FORTH IN THIS LICENSE,
TRILLIANT ASSUMES NO RESPONSIBILITIES OR LIABILITIES WHATSOEVER WITH RESPECT TO
USE OR SALE BY EITHER LICENSEE OR ITS VENDEES OR TRANSFEREES OF COMBINED
PRODUCTS.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
TRILLIANT RESERVES THE RIGHT TO CHANGE THE PRODUCT SPECIFICATIONS WITHOUT
CONSEQUENCE OF LIABILITY.
Trilliant Incorporated
1100 Island Drive, Redwood
City, CA 94065 USA
+1.650.204.5050
www.trilliantinc.com
Trilliant™, CellReader®, CellGateway™, SecureMesh™, SerViewCom®, UnitySuite™,
SkyPilot®, SyncMesh™, the Trilliant logo, and the SkyPilot logo are trademarks of
Trilliant Incorporated and/or its subsidiaries. All other trademarks are the property of
their respective owners.
Copyright © 2015 Trilliant Incorporated. ALL RIGHTS RESERVED.
DT‐0237Apage3of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
TableofContents
1
Overview..................................................................4
2
FeaturesandSpecifications.......................................4
SecureMeshNANRadioPerformance..................4
Electricalspecifications.........................................4
Physical,&Environmental....................................5
Compliance...........................................................5
3
FunctionalDescription..............................................6
OSDIModule.........................................................6
HostInterface&OptionalIOs...............................6
InterfaceandControlSignals...............................6
4
Antennas..................................................................8
AntennaPlacement..............................................8
Externalantennas.................................................9
5
HostPCBRequirements...........................................11
RecommendedFootprint....................................11
PasteMask..........................................................11
Layoutrequirements..........................................11
Referencetracedesign.......................................12
ModifyingtheRFSignalRouting........................13
PinNumbering....................................................15
PinDescription....................................................15
SuggestedReflowprofile,forreferenceonly......21
6
SecureMeshConfiguration.......................................21
MeshProgrammingtool....................................21
DataLinkLibrary................................................21
7
RegulatoryAgencyApprovals..................................22
UnitedStates......................................................22
Canada...............................................................23
Figures
Figure1:TypicalapplicationwithOSDIModule.............................................................................................................................6
Figure2:LarsenRO2406NMDrawing.............................................................................................................................................9
Figure3:LarsenRO2406NMRadiationPatterns.............................................................................................................................9
Figure4:MobileMarkCVS‐2400..................................................................................................................................................10
Figure5:MobileMarkCVS‐2400RadiationPatterns....................................................................................................................10
Figure6FootprintOSDI‐4000‐1X..................................................................................................................................................11
Figure7FCCandICapprovedtracedesignlayoutandpicture.....................................................................................................12
Figure8Couponrequirementstovalidatetraceimpedance........................................................................................................13
Figure9:Micro‐striptraceparameters.........................................................................................................................................14
Figure10:Examplestack‐up........................................................................................................................................................14
Figure11:50ohmscalculation(mm)Tracewidth:0.7mmCopperclearance:0.1445mm..............................................................14
Figure12:PinNumberingDiagramBottomview..........................................................................................................................15
Figure13:PreliminaryOSDIModuleReflowProfileandSetPoints...............................................................................................21
Tables
Table1:OSDImodulecontrolsignalsdescriptionandusage..........................................................................................................6
Table2Antennamicro‐striptraceparts......................................................................................................................................13
Table3:Pinnumberingdetails.....................................................................................................................................................20
DT‐0237Apage4of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
1 Overview
The SecureMesh Ready, Open Smart Device Interface Modules (OSDI) are Trilliant 2.4GHz RF modules which can be integrated into a
variety of third party OEM products. These small and versatile modules include a microcontroller, memory, transceiver, power
management all on an LGA circuit board.
Based on IEEE 802.15.4 wireless communication standard and utilizing Trilliant’s robust SecureMesh networking protocol, the OSDI
modules deliver industry leading 2.4GHz networking solution. The modules are easy to integrate, provide low power consumption, long
range and many more features and functionalities.
The OSDI family of products are currently available in 2 base hardware models:
Hardware Model Description
OSDI-4000-1A 4
th
generation OSDI module with maximum transmit power of 1 watt; ANSI protocol
OSDI-4000-1D 4
th
generation OSDI module with maximum transmit power of 1 watt; DLMS/COSEM Protocol
Throughout the remainder of this document, the OSDI module platforms will be referred to by the base hardware model.
2 FeaturesandSpecifications
The OSDI modules are designed for a broad range of applications and products, and provide a compliant ready RF mesh solution for both
domestic and international markets. The modules have a unique set of features, including:
Reporting Retries and Acknowledgements.
Remote Firmware upgrades.
Programmable Network Parameters.
AES, DES Encryption crypto module.
Frequency hopping for a reliable communication link against interference (future enhancement)
SecureMeshNANRadioPerformance
Protocols
SecureMesh NAN Transport layer
SecureMesh NAN Network layer
IEEE 802.15.4 MAC layer
IEEE 802.15.4 PHY layer (2.4 GHz)
Modulations
DSSS – OQPSK
Direct Sequence Spread Spectrum
Offset Quadrature Phase-Shift Keying
Data rate: 250 kbps (transmit/receive)
Frequency band 2.400 - 2.4835 GHz (unlicensed operation)
Frequency channels 15
Channel spacing 5 MHz
Maximum transmit power +30dBm
Receive sensitivity -103dBm
Electricalspecifications
Min. Typ. Max.
Voltage 4.0 4.5 5.0
Current 1. 2A
DT‐0237Apage5of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Physical,&Environmental
Mounting method LGA (Land Grid Array)
Dimensions (L x W x H) 29.8 x 35.3 x 4.4 mm
Operating temperature -40 °C to +85 °C
Humidity 5 to 95% non-condensing
Compliance
Radio emissions
FCC Part 15 Class B
Industry Canada ICES-003 Class B
MID
others pending
Unlicensed radio operation
FCC Part 15.212, 15.247
Industry Canada RSS-Gen, RSS-247
MID
others pending
Human Exposure FCC Part 1.1310
RSS-102
DT‐0237Apage6of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
3 FunctionalDescription
OSDIModule
The OSDI modules are low power 2.4GHz ISM band transceivers. Figure 1 below shows a block diagram of the OSDI-4000 modules and
the surrounding optional functionalities that are intended as a reference implementation example.
The configuration of the transceiver, reading and writing of Frame Buffer is controlled by a SPI interface and additional control lines. The
control of the RF front-end is done via the transceiver digital control pins.
The OSDI modules are equipped with a Low Drop Out voltage (LDO) regulator that enables them to work in standalone mode with a
voltage supply between 4 and 5 volts.
The VCPU power supply line of the microcontroller is available on the external connection for optional backup supply when Real Time
Power Outage Reporting (RTPOR) is required.
Figure 1: Typical application with OSDI Module
HostInterface&OptionalIOs
Communication with the host is achieved using a serial communication port and control signals that are bundled with the power lines
inside the host connector. Diagnostic and programming signals are available to the host. See Table 1 below for the description of the
various signals found in the diagnostic and programming interface. The RF input/output signal must be routed through the host device as
described in section 5.4. Antennas of section 4 can be used in relation with regulation. The OSDI module is designed with outputs to
drive a multicolor LED indicator that allows visual diagnostic and status monitoring of the device. See Table 1 below for an interpretation
of the existing LED patterns.
InterfaceandControlSignals
Table 1: OSDI module control signals description and usage.
Signal Description Usage
TX_EXT-RX_LGA Transmit from the meter / Receive to the
module.
Signal Type: UART.
Meter Connector serial port.
Meter USB Port.
Default baud rate is set to 9.6 kbps.
RX_EXT-TX_LGA Receive to the meter / Transmit from the
module.
Signal Type: UART.
DT‐0237Apage7of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Signal Description Usage
DIAG-RX_LGA Module receive diagnostic port.
Signal Type: UART.
Diagnostic serial port
Diagnostic USB Port.
Default baud rate is set to 9.6 kbps in diagnostic mode
and 19.2 kbps in trace mode.
Should be accessible via test points in normal design.
DIAG-TX_LGA Module transmit diagnostic port.
Signal Type: UART.
RED_LED and
GRN_LED
Control Red and Green LEDs.
Signal Type: Active low output.
0=LED on, 1= LED off.
Note: Red and green led are in one physical
unit. Yellow is produced when both LEDs
are on.
Diagnostic LEDs.
Needs to be visible from the outside of the meter for
installation purposes in normal design.
LEDs off: Power save mode/POR mode or no power.
Flashing green: Initialization (5 sec).
Steady Red: Working but not associated to a network.
Steady Yellow: Working and trying to associate to a network.
Steady Green: Working and associated to a network.
Flashing Yellow: Working and exchanging info.
P-FAIL_EXT External signal from the meter indicating
that an interruption of power has been
detected.
Signal Type: Active low input from the
meter.
0 = Power fail, 1 = Normal condition.
Meter Connector.
PFAIL Circuit.
Provides an early detection of power outage events.
P-FAIL Signal indicating that an interruption of
power has been detected.
Signal Type: Interrupt input.
0 = Power fail, 1 = Normal condition.
PFAIL Circuit.
CPU Reset Control Circuit.
Provides early detection of power outage events.
RESET Signal Type: Hardware reset.
0 = Reset, 1 = Normal operation.
CPU Reset Control Circuit.
For use during development only.
Do not connect to the meter.
TEST Select test / diagnostic mode.
Signal Type: Active high input.
1 = Diagnostic mode, 0 = Normal mode.
Reserved
Diagnostic/Programming Connector.
Should be accessible via test points in normal design.
SC_HI Signal Type: Input.
1 = Supercap voltage > 3.6V
On/off signal from the fail safe circuit to detect if the
super cap is higher than 3.6V.
PWR_MON Power supply monitoring signal.
Signal Type: Analog.
Meter Connector.
Provision for self-detection of power outages by the OSDI
modules, if P-FAIL is not available.
RESET-PDI_CLK,
TDI-PDI_DATA,
TDO, TMS, TCK
Program and Debug Interface.
Diagnostic/Programming Connector.
Used only during development.
See schematic for proper use.
Should be accessible via test points in normal design.
SLEEP Sleep mode power activation.
Signal Type: low open-drain output.
0 = SLEEP Enabled, 1 = SLEEP Disabled.
RTPOR Supply Management circuit.
Used to send the command to the power management circuit
to connect the 1.5 Farad capacitor (+V1.5F) directly to the
input supply (+VCPU) of OSDI module’s CPU in order to feed
it with minimum power waste, in sleep mode.
MESURE_VCAP 1.5 Farad capacitor voltage monitoring.
Signal Type: Analog, feeds ADC input.
Provision for monitoring of voltage level of the 1.5F capacitor.
+3.3V LDO voltage regulator’s output. Regulated 3.3V voltage supply from the OSDI module.
+VMAIN Main power supply input. Used by the power management circuit as input to the LDO
regulator and to charge the 1.5 Farad super capacitor.
+VCPU2 3.3 Volts supply for OSDI module’s CPU. Used to feed power to the CPU during debug and
programming.
+VCPU 3.3 Volts supply for OSDI module’s CPU. Input supply (+VCPU) of OSDI module’s CPU.
+VLDO_IN LDO regulator’s input. Input of the LDO regulator (+VLDO) of the OSDI module.
+V1.5F_SW 1.5 Farad capacitor switched voltage. Power path for the sleep mode power supply.
DT‐0237Apage8of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
4 Antennas
The maximum output power authorized by the FCC and industry Canada in the 2.4GHz band is 36 dBm EIRP. For the OSDI-4000-1X,
the maximum output power of the radio is 30 dBm which can be combined to an antenna with a maximum gain of 6 dBi.
The OSDI module has been certified with two different types of integrated antennas as described in the following sections. The information
shown was taken from datasheets or measured when mounted on specific products. Actual patterns will be influenced by the PCB layout
and by surrounding material.
NOTE: Certification regulations differ from one country to the other. It remains the responsibility of the meter manufacturer to
choose an antenna that will meet the requirements of the country where the meters will be deployed as well as any local
certifications that may be required to comply with specific market regulations. See section 7 for more details.
AntennaPlacement
Antenna performance is significantly impacted by the type and physical placement of the antenna. The antenna should be oriented in the
device to properly radiate the RF emissions from the face of the device forward and in an upward direction for optimal connectivity to the
Trilliant SecureMesh network infrastructure. In addition, there should be as few obstacles as possible between the antenna and the outside
of the device.
Through the following examples, Trilliant is attempting to provide antenna options for the most commonly used antenna design scenarios
but keep in mind that this is greatly dependent on the host device design. If you are unsure about which antenna to select, or how it should
be implemented into the overall design, please contact Trilliant for guidance.
The RF connection from the OSDI module to the antenna is made using a 50 ohms micro-strip trace on the host’s PCB. See section 5.4
for routing instructions.
DT‐0237Apage9of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Externalantennas
The following section describes types of external antennas that have been certified with the OSDI-4000 module.
Note that a Reverse Polarity connector must be used for external antennas.
4.2.1 LarsenRO2406NM
Vendor: Larsen
Vendor #: RO2406NM
Frequency: 2400-2500 MHz
Nominal Impedance: 50 Ohms
VSWR: 2:1 Max
Gain: 6 dBi
Polarization: Vertical
Power withstanding: 20 W
Connector: N-Type Male (To use this antenna with the OSDI
module, a RP connector that is actually in discussion, must be
used; the part number will change accordingly)
Figure 2: Larsen RO2406NM Drawing.
Figure 3: Larsen RO2406NM Radiation Patterns.
DT‐0237Apage10of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
4.2.2 MobileMarkCVS‐2400
Vendor = Mobile Mark
Vendor #: CVS-2400-2SA-BLK-13
Frequency: 2.4 – 2.5 GHz
Gain: 2.0 dBi max
VSWR: 2:1 over band
Impedance: 50 ohm nominal
Maximum Power: 10 Watts
Connector: SMA Plug-RP
Temperature Range: -40° to +85°C
Antenna Dimensions:
3 3/4" Length x 1 1/4" Width x 3/8” Deep
(95 mm x 32 mm x 9 mm)
Figure4:MobileMarkCVS‐2400.
Figure 5: Mobile Mark CVS-2400 Radiation Patterns.
DT‐0237Apage11of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
5 HostPCBRequirements
RecommendedFootprint
The footprints shown below are available upon request as a PAD Layout source file.
OSDI-4000-1X
Overall (L x W x H), including shield: 29.8 x 35.3 x 4.0mm
Suggested Silkscreen Outline (L x W): 30.3 x 35.8mm
Avoid vias, traces or copper inside Keep-Out Areas
Figure 6 Footprint OSDI-4000-1X
PasteMask
Paste Mask Stencil openings can be of the same size as the recommended footprint (1:1); suggested thickness of stencil foil ≥ 120µm.
Layoutrequirements
Traces routed to RF_EXT pad must be 50 ohm.
Traces current rating:
+VCPU ≥ 90 mA
+3.3V ≥ 90 mA
+VLDO_IN ≥ 1.4 Amp
+V1.5F_SW ≥ 90mA
Thermal reliefs are strongly recommended for all pads connected to Ground net.
Finish recommendation for PCB pad surfaces: ROHS Compliant (EU Directive 2002/95/EC) 2-10 µIN Immersion Gold Over 50-
200µIN Electro less Nickel (ENIG)
Non Solder Mask Defined (NSMD) type is recommended for the solder pads on the PCB.
DT‐0237Apage12of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Pads Solder Mask Opening of 0.1mm is recommended.
Referencetracedesign
5.4.1 Layoutandparts
RF traces from OSDI module pads W10 and W16 to the antenna must be made using micro-strip traces. This micro-strip trace must
respect the design of the Gerber file associated with the following figures in order to obtain a uniform transmission line with a characteristic
impedance of 50 ohms. The reference trace design is shown as the green trace along with the side copper filled with vias on the left side
of Figure 7 where components G8, G10, G15, G16 and G18 are not installed; they were options on the reference board for future uses;
these uses are not FCC authorized yet. As preliminary information the traces width of all sections are all 0.27mm and the length of each
section, starting from the LGA pad to J53 connector are: LGA pad to G7: 15.38mm; G7 to G9: 12.37mm; G9 to G17: 6.7mm; G17 to R52:
2.1mm; R52 to J53: 7.2mm. However, refer to associated Gerber files for more accurate details on dimensions and refer to Trilliant
Networks Inc for more details on the Gerber files. Table 2 shows the parts used in the reference trace design.
Figure 7 FCC and IC approved trace design layout and picture
DT‐0237Apage13of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Table 2 Antenna micro-strip trace parts
Part Number Designator Description Manufacturer
N/A G8, G10, G15, G16, G18 Not installed N/A
RK73Z1ETTP G7, G9, G17, R52 RESISTOR 0.0 OHMS 1/16W 5% 0402 SMT KOA Speer Electronics
LQW18AN75NG00D L2 INDUCTOR 75nH, 2%, 270mA 560mΩ, 0603 SMT Murata Manufacturing
1-1478979-0 J53 SMA JACK CONNECTOR (FEMALE) PCB Mount 4
legs, SS/Gold pl.
TE Connectivity
5.4.2 Designvalidation&productionprocedures
To verify compliance of the reference trace, a coupon must be requested with every manufacturing panel form and for which the
characteristics are described in the Gerber files. Part of these characteristic are shown in Figure 8. Then a network analyzer is used to
measure the impedance of this coupon in order to validate the antenna trace.
Figure 8 Coupon requirements to validate trace impedance
5.4.3 Otherconsiderations
The only antennas, also describe is section 4.2, that can be used with the module using the reference trace design are the:
- Larsen Antennas, RO2406NM, 6 dBi
- Mobile Mark, CVS-2400, 2.5 dBi
The use of any other antenna or any changes to the reference trace design are subject to additional testing and authorization through a
Class II permissive change.
ModifyingtheRFSignalRouting
As previously mentioned, any changes to the RF traces is subject to approbation, additional testing and authorization through a Class II
permissive change on the FCC and IC grants.
The objective is to use the W10 and W16 pads from OSDI module to route a micro-strip traces in order to obtain a uniform transmission
line with a characteristic impedance of 50 ohms. The characteristic impedance depends on the geometry of the trace and on the relative
dielectric constant of the PCB as shown in Figure 9. However, the characteristic impedance does not depend on the length of the trace.
Many tools are available on the web to help calculate the optimum dimensions.
DT‐0237Apage14of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Figure 9: Micro-strip trace parameters
H1 and T1 are taken from the stack-up parameter of the host’s PCB as shown in Figure 10, the relative dielectric constant depend on the
material used.
Figure 10: Example stack-up
An example stack-up, copper thickness, RF traces width and traces to copper clearance in order to get 50 ohms is presented below. The
calculation toll is then used to find the remaining parameters of the micro-strip traces as shown in Figure 11.
Figure 11: 50 ohms calculation (mm) Trace width: 0.7mm Copper clearance: 0.1445mm
The resulting parameters can then be used to define the trace width and copper clearance on RF traces of the host’s PCB. The RF traces
must be surrounded by copper all along the path of undefined length; the path should be as short as possible to reduce losses. Vias must
be added all along the RF traces. See reference trace design in Figure 7 for an example.
Note: a new trace design is subject to validation, additional testing and authorization through a Class II Permissive change on
the FCC and IC grants.
DT‐0237Apage15of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
PinNumbering
Figure 12: Pin Numbering Diagram
Bottom view
PinDescription
Pad Name Description
A2 *8_NRSTTestpointonly
A3 PB31Donotconnect
A4 PB23/AD4SpareI/O
A5 PA12/AD0SpareI/O
A6 RESERVEDDonotconnect
A7 +VCPU+VCPU
A8 *12_PA16SpareI/O
A9 PB28SpareI/O
A10 PB4/RX0Testpointonly
A11 PB5/TX0Testpointonly
A12 PB7StatusLED
A13 RESERVEDDonotconnect
DT‐0237Apage16of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Pad Name Description
A14 +VCPU+VCPU
A15 RESERVEDDonotconnect
A16 PA0_*1SpareI/O
A17 *1_PB26SpareI/O
B1 PA13/SCK_EXT1ProvisionforexternalSPI
B2 PA14/CS_EXT1ProvisionforexternalSPI
B3 PA15SpareI/O
B4 PB27Powermanagementsignal
B5 RESERVEDDonotconnect
B6 RESERVEDDonotconnect
B7 RESERVEDDonotconnect
B8 RESERVEDDonotconnect
B9 PA2_*5SpareI/O
B10 RESERVEDDonotconnect
B11 SHDNPowermanagementsignal
B12 PB8StatusLED
B13 PB25SpareI/O
B14 PB10_*4SpareI/O
B15 PB14_*5SpareI/O
B16 PB11_*6SpareI/O
B17 PB12_*1SpareI/O
B18 PB16/MISO_EXT2_*2SpareI/O
C1 PA10/MOSI_EXT1ProvisionforexternalSPI
C2 PB1/TDO_*11SpareI/O
C3 RESERVEDDonotconnect
C4 PA17/PFAILPowermanagementsignal
C5 RESERVED Donotconnect
C6 RESERVEDDonotconnect
C7 RESERVEDDonotconnect
C8 RESERVEDDonotconnect
C9 RESERVEDDonotconnect
C10 RESERVEDDonotconnect
C11 +VCPU+VCPU
C12 GND_NCDonotconnect
C13 PB29SpareI/O
C14 RESERVEDDonotconnect
C15 PC0/TX1Meterinterface
DT‐0237Apage17of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Pad Name Description
C16 RESERVEDDonotconnect
C17 RESERVEDDonotconnect
C18 RESERVEDDonotconnect
D1 PA9/MISO_EXT1ProvisionforexternalSPI
D2 PB3/TCK_*11SpareI/O
D3 PB2/TMS_*11SpareI/O
D16 GND_NCDonotconnect
D17 RESERVEDDonotconnect
D18 PC1/RX1Meterinterface
E1 *9_NRSTTestpointonly
E2 RESERVEDDonotconnect
E3 PB13/AD3Powermanagementsignal
E16 PA19/CS_EXT2_*2SpareI/O
E17 PB18/SCK_EXT2_*2SpareI/O
E18 PB17/MOSI_EXT2_*2SpareI/O
F1 PB0/TDISpareI/O
F2 PA4/AD1Powermanagementsignal
F3 RESERVEDDonotconnect
F16 RESERVEDDonotconnect
F17 RESERVEDDonotconnect
F18 +VLDO_INInputofLGALDO
G1 RESERVEDDonotconnect
G2 *3_PC5SpareI/O
G3 +VCPU+VCPU
G16 GND_NCDonotconnect
G17 GND_NCDonotconnect
G18 +VLDO_INInputofLGALDO
H1 RESERVEDDonotconnect
H2 GND_NCDonotconnect
H3 RESERVEDConnectedtoGndvia0ohmsresistor.
H16 GND_NCDonotconnect
H17 GND_NCDonotconnect
H18 GND_NCDonotconnect
J1 GND_NCDonotconnect
J2 GND_NCDonotconnect
J3 RESERVEDConnectedtoGndvia0ohmsresistor.
J16 GND_NCDonotconnect
DT‐0237Apage18of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Pad Name Description
J17 GND_NCDonotconnect
J18 GND_NCDonotconnect
K1 GND_NCDonotconnect
K2 GND_NCDonotconnect
K3 RESERVEDDonotconnect
K16 RESERVEDDonotconnect
K17 RESERVEDDonotconnect
K18 XIN3232KHzxtal
L1 GND_NCDonotconnect
L2 GND_NCDonotconnect
L3 GND_NCDonotconnect
L16 PB15_*13SpareI/O
L17 +3.3VOutputfromLGALDO
L18 XOUT3232KHzxtal
M1 GNDGND
M2 RESERVEDDonotconnect
M3 GND_NCDonotconnect
M16 GNDGND
M17 GNDGND
M18 +V1.5F_SWLGAbackuppower
N1 GNDGND
N2 GND_NCDonotconnect
N3 GNDGND
N16 GNDGND
N17 GNDGND
N18 +3.3VOutputfromLGALDO
P1 GNDGND
P2 GND_NCDonotconnect
P3 GND_NCDonotconnect
P16 GNDGND
P17 GNDGND
P18 +3.3VOutputfromLGALDO
R1 GNDGND
R2 GND_NCDonotconnect
R3 GNDGND
R16 GNDGND
R17 GNDGND
DT‐0237Apage19of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Pad Name Description
R18 GNDGND
T1 GNDGND
T2 GND_NCDonotconnect
T3 GND_NCDonotconnect
T16 GNDGND
T17 GNDGND
T18 GNDGND
U1 GNDGND
U2 GNDGND
U3 GNDGND
U16 GNDGND
U17 GNDGND
U18 GNDGND
V1 GNDGND
V2 GND_NCDonotconnect
V3 RESERVEDDonotconnect
V4 GNDGND
V5 GNDGND
V6 GNDGND
V7 RESERVEDDonotconnect
V8 GNDGND
V9 GNDGND
V10 GNDGND
V11 GNDGND
V12 GNDGND
V13 GNDGND
V14 GNDGND
V15 GNDGND
V16 GNDGND
V17 GNDGND
V18 GNDGND
W1 GNDGND
W2 GND_NCRESERVEDDonotconnect
W3 GNDGND
W4 RESERVEDDonotconnect
W5 RESERVEDDonotconnect
W6 GNDGND
DT‐0237Apage20of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
Pad Name Description
W7 RESERVEDDonotconnect
W8 RESERVEDDonotconnect
W9 GNDGND
W10 RESERVEDDonotconnect
W11 GNDGND
W12 GNDGND
W13 GNDGND
W14 RESERVEDDonotconnect
W15 GNDGND
W16 RF_EXT1RFto/fromantenna
W17 GNDGND
W18 GNDGND
Y2 GNDGND
Y3 GNDGND
Y4 GNDGND
Y5 GNDGND
Y6 GNDGND
Y7 GNDGND
Y8 GNDGND
Y9 GNDGND
Y11 GNDGND
Y12 GNDGND
Y13 GNDGND
Y14 RESERVEDDonotconnect
Y15 GNDGND
Y17 GNDGND
Table 3: Pin numbering details.
DT‐0237Apage21of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
SuggestedReflowprofile,forreferenceonly
Figure 13: Preliminary OSDI Module Reflow Profile and Set Points.
6 SecureMeshConfiguration
The configuration of the OSDI module is the last step in the manufacturing process, just before shipping to the customer. This process
consists of configuring of programming the customer related parameters as applicable, via the SecureMesh network, using the Mesh
Programming tool.
MeshProgrammingtool
Trilliant’s Mesh Programming tool is an MS Windows application that communicates with the OSDI modules using a SecureMesh USB
radio dongle.
The configuration file is generated by Trilliant for each deployment project to define the configuration parameters for each OSDI module
in a given SecureMesh network.
Refer to document DP-1145 for more details.
DataLinkLibrary
A DLL can also be used for volume production. It contains the necessary functions to allow the automatic test equipment to configure the
OSDI modules according to the configuration file generated by Trilliant.
DT‐0237Apage22of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
7 RegulatoryAgencyApprovals
Modular approval allows end users to place the OSDI module inside a finished product without the need for regulatory testing, provided
no changes or modifications are made to the module circuitry. Changes or modifications could void the user’s authority to operate the
equipment. The end user must comply with all of the instructions provided by the grantee, which indicate installation and/or operating
conditions necessary for compliance.
The OSDI Module has been tested and conforms to FCC and IC regulation for unlicensed transmitter module. The module tests can be
applied toward final product certification. Additional testing may be required depending on the targeted application.
The integrator may still be responsible for testing the end product for any additional compliance requirements that become necessary.
For more information on regulatory compliance, refer to the specific country radio regulations in the following sections.
UnitedStates
With the approval of Federal Communications Commission (FCC) CFR47 Telecommunications, Part 15 Subpart C-Intentional Radiators
15.212 Modular Transmitter approval, the OSDI module is authorized to be integrated into a finished product without obtaining subsequent
and separate FCC approvals for intentional radiation.
The OSDI module is labeled with its own FCC ID number. If the FCC ID is not visible when the module is installed inside another device,
then the outside of the finished product into which the module is installed shall display a label referring to the enclosed module. This
exterior label shall bear the following statement:
A user manual for the finish product shall include the following statement:
7.1.1 RFHumanExposure
All transmitters regulated by FCC must comply with RF exposure requirements. Part 1.1310, Evaluating Compliance with FCC
Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields, provides assistance in determining whether proposed
or existing transmitting facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by
the Federal Communications Commission (FCC). The bulletin offers guidelines and suggestions for evaluating compliance.
Contains Transmitter Module FCC ID: TMB-OSDI4W1
Or
Contains FCC ID: TMB- OSDI4W1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
DT‐0237Apage23of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
If appropriate, compliance with exposure guidelines for mobile and unlicensed devices can be accomplished by the use of warning labels
and by providing users with information concerning minimum separation distances from transmitting structures and proper installation of
antennas.
The following statement must be included as a CAUTION statement in manuals and OEM products to alert users of FCC RF exposure
compliance:
If the OSDI modules are used in a portable application (i.e., the antenna is less than 20 cm from persons during operation), the integrator
is responsible for performing Specific Absorption Rate (SAR) testing in accordance with FCC rules 2.1091.
7.1.2 ApprovedExternalAntennaTypes
To maintain modular approval in the United States, only the antenna types that have been tested shall be used. It is permissible to use
different antenna manufacturer provided the same antenna type and antenna gain (equal to or less than) is used. Also, the antenna(s)
used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Testing of the OSDI module has been performed with the antenna types listed in Section 4.2 above.
7.1.3 HelpfulWebSites
Federal Communications Commission (FCC):
http://www.fcc.gov.
Canada
The OSDI module targets certification for use in Canada under Industry Canada (IC) Radio Standards Specification (RSS) RSS-247 and
RSS-Gen. Modular approval permits the installation of a module in a host device without the need to recertify the device.
Labeling Requirements for the Host Device (from Section 7.2, RSP-100, Issue 10, November 2014):
The host device shall be properly labeled to identify the module within the host device.
The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host
device must be labeled to display the Industry Canada certification number of the module, preceded by the words “Contains transmitter
module”, or the word “Contains”, or similar wording expressing the same meaning, as follows:
User Manual Notice for License-Exempt Radio Apparatus (from Section 8.4 RSS-Gen, Issue 4, November 2014):
User manuals for license-exempt radio apparatus shall contain the following or equivalent notice in a conspicuous location in the user
manual or alternatively on the device or both:
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more
should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer
than this distance is not recommended.
Contains transmitter module IC: 6028
A
-OSDI4W1
Or
Contains IC: 6028A-OSDI4W1
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
DT‐0237Apage24of24Rev:1.0
CONFIDENTIAL
DISTRIBUTED UNDER LICENSE
7.2.1 RFHumanExposure
All transmitters regulated by Industry Canada must comply with RF exposure requirements. RSS-102, Radio Frequency (RF) Exposure
Compliance of Radiocommunication Apparatus (All Frequency Bands), sets out the requirements and measurement techniques
used to evaluate radio frequency (RF) exposure compliance of radiocommunication apparatus designed to be used within the vicinity of
the human body.
If appropriate, compliance with exposure requirements for mobile and unlicensed devices can be accomplished by the use of warning
labels and by providing users with information concerning minimum separation distances from transmitting structures and proper
installation of antennas.
The following statement must be included as a CAUTION statement in manuals of OEM products to alert users of Industry Canada RF
exposure compliance:
If the OSDI modules are used in a portable application (i.e., the antenna is less than 20 cm from persons during operation), the integrator
is responsible for performing Specific Absorption Rate (SAR) testing in accordance with Industry Canada RSS-102.
7.2.2 ApprovedExternalAntennaTypes
The OSDI modules may operate with different types of antennas. However, it is not permissible to exceed the maximum equivalent
isotropically radiated power (e.i.r.p.) limits specified in the applicable standard (RSS) for the licence-exempt apparatus.
Testing shall be performed using the highest gain antenna of each combination of transmitter and antenna type, with the transmitter output
power set at the maximum level. When a measurement at the antenna connector is used to determine RF output power, the effective gain
of the device's antenna shall be stated, based on measurement or on data from the antenna manufacturer. User manuals for transmitters
equipped with detachable antennas shall also contain the following notice in a conspicuous location:
Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use with the transmitter,
indicating the maximum permissible antenna gain (in dBi).
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Projected approved external antenna types for the OSDI modules are listed in Section 4.2 above.
7.2.3 HelpfulWebSites
Industry Canada: http://www.ic.gc.ca/
To satisfy Industry Canada RF Exposure requirements for mobile and base station transmission devices, a separation distance of
20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance,
operation at closer than this distance is not recommended.
Pour satisfaire les requis d'industrie Canda sur les expositions aux radiofréquences pour les appareils mobiles et les stations de
transmission, une distance de 20 cm ou plus doit être maintenue entre l'antenne de cet appareil et les personnes durant l'opération.
Pour assurer la conformité, les opérations à des distances inférieures ne sont pas recommandées.
This radio transmitter TMB-OSDI4W1 has been approved by Industry Canada to operate with the antenna types listed below with the
maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated
for that type, are strictly prohibited for use with this device.
Le présent émetteur radio TMB-OSDI4W1 a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés
ci‑dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.