Trimble 99133 Smart Receiver Accessory User Manual

Trimble Navigation Limited Smart Receiver Accessory Users Manual

Users Manual

Download: Trimble 99133 Smart Receiver Accessory User Manual
Mirror Download [FCC.gov]Trimble 99133 Smart Receiver Accessory User Manual
Document ID2446477
Application IDmu/cdzBKPANoVrV8huCwhg==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize58.81kB (735113 bits)
Date Submitted2014-11-17 00:00:00
Date Available2015-05-16 00:00:00
Creation Date2014-10-28 14:26:46
Producing SoftwareAdobe PDF Library 10.0.1
Document Lastmod2014-11-17 11:02:53
Document TitleUsers Manual
Document CreatorAdobe InDesign CS6 (Windows)

Trimble PG200 GNSS receiver
Quick Start Guide
Download Trimble GNSS Status utility
• Windows, Windows Embedded Handheld: www.trimble.com
• Android: Google Play store
• iOS: iTunes
Trimble Support
TR
IMBLE
SU
PPORT
http://www.trimble.com/locator/locator.aspx
Made for
•
iPhone 6 Plus, iPhone 6
•
iPhone 5s, iPhone 5c, iPhone 5
•
iPad Air
•
iPad mini with Retina display
•
iPad (4th generation)
•
iPad mini
“Made for iPhone,” and “Made for iPad” mean that
an electronic accessory has been designed to connect
specifically to iPhone or iPad, respectively, and has
been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPhone or iPad may affect
wireless performance.
Trimble® PG200 GNSS Receiver
©2014. Trimble Navigation Limited. All rights reserved. This product
is protected by US and international copyright, trademark, and
patent law as described in "Legal Notices" in the Trimble PG200
GNSS Receiver User Guide. PN 102388-00-ENG, Revision A (10/2014)
*102388-00-ENG*
Trimble Navigation Limited
10368 Westmoor Drive
Westminster, CO 80021
USA
www.trimble.com
CAUTION: Please read the full user
guide including all safety warnings,
before operating this product.
PDF
102388-00-ENG
PG200_ENG_QSG_MCS_1014.indd 2
10/28/2014 2:26:51 PM
LED information and power off
Charging and operation
1. Charge battery
2. Turn on
1.
5h
Bluetooth / GNSS LED
GNSS
Hold Power button
LED =
LED =
- - -
Pairing mode
N/A
--- --- ----- --- ---
2.
--- --- ---
When LEDs = ,
release Power button.
After a few seconds,
------ ------ ------
LED = --- --- ---
3.
Bluetooth connection					
PDF
1.
Hold Power button for 5 seconds
until
LED = - - -
Solid
Power LED
Corrected
1.
Solid
<100%
Solid
100%
Off
2. Use the Trimble® GNSS Status utility for:
• Windows® 7, 8.x
• Trimble Juno® 3 handheld
(Windows Embedded Handheld 6.5)
• Android* 4.1.x and later
Use Settings > Bluetooth® for:
• iOS
Turn off
>50%
--- --- ---
<50%
--- --- ---
<15%
- - -
Hold Power button
LED =
LED =
2.
When
LED = Off
and
LED = ,
release the Power
button.
Both LEDs = Off
*On Android devices, enable Mock Locations. See the Trimble PG200 GNSS
Receiver User Guide for more information.
PG200_ENG_QSG_MCS_1014.indd 3-4
10/28/2014 2:27:02 PM
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired
operation.
The device and its antenna must not be co-located or operating in conjunction with any other
antenna or transmitter. Users are not permitted to make changes or modify the device in any way.
Changes or modifications not expressly approved by Samsung will void the user’s authority to
operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled
environment. This device and its
antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
Part 15.105 (B)
Note : This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications, However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void your authority to operate the
equipment under FCC rules.
Industry Canada Statment
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference and (2)this
device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Industry Canada RF Radiation Exposure Statement
This equipment complies with Industry Canada RF Radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with any other
antenna or transmitter.
RF de l'Industrie Canada d'exposition aux radiations: Cet équipement est conforme à l'exposition de
l'Industrie Canada rayonnements RF limites établies pour un
environnement non contrôlé. L’antenne pour ce transmetteur ne doit pas être meme endroit avec
d’autres émetteurs sauf conformément à l'Industrie Canada procedures de produits Multi-émetteur.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Create Date                     : 2014:10:28 14:26:46+13:00
Metadata Date                   : 2014:11:17 11:02:53+09:00
Modify Date                     : 2014:11:17 11:02:53+09:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:54e364ea-4118-4489-9dd6-c85245ba0744
Original Document ID            : adobe:docid:indd:66815205-756d-11dd-8d50-d891d9e9a92b
Document ID                     : xmp.id:206FE164415EE41186DF8F66484782D2
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:1F6FE164415EE41186DF8F66484782D2
Derived From Document ID        : xmp.did:4510E5A62750E411B56CE1DF224C0C98
Derived From Original Document ID: adobe:docid:indd:66815205-756d-11dd-8d50-d891d9e9a92b
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:10:28 14:26:46+13:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 5
Creator                         : Adobe InDesign CS6 (Windows)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: S9E99133

Navigation menu