Troybilt 24A 060F063 User Manual YARD VACUUM/CHIPPER/SHREDDER/HOSE Manuals And Guides L0401057
TROYBILT Chipper Shredder/Vacuum, Gas Manual L0401057 TROYBILT Chipper Shredder/Vacuum, Gas Owner's Manual, TROYBILT Chipper Shredder/Vacuum, Gas installation guides
User Manual: Troybilt 24A-060F063 24A-060F063 TROYBILT YARD VACUUM/CHIPPER/SHREDDER/HOSE - Manuals and Guides View the owners manual for your TROYBILT YARD VACUUM/CHIPPER/SHREDDER/HOSE #24A060F063. Home:Lawn & Garden Parts:Troybilt Parts:Troybilt YARD VACUUM/CHIPPER/SHREDDER/HOSE Manual
Open the PDF directly: View PDF .
Page Count: 20
Download | |
Open PDF In Browser | View PDF |
OPERATOR'S MANUAL Yard Vacuum \ Chi pper/Shredder/ Vacuum/Hose \ \ Model Number 24A-060F063 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark attester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. TROY-BILT PRINTED IN U.S.A. LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 FORM NO. 769-00169 (4/02) TABLEOFCONTENTS Content Page Important Safe Operation Practices ................................................................... 3 Assembling Your Yard Vacuum ......................................................................... 5 Know Your Yard Vacuum ................................................................................... 7 Operating Your Yard Vacuum ............................................................................ 8 Maintaining Your Yard Vacuum ......................................................................... 10 Troubleshooting ................................................................................................. 13 Parts List ............................................................................................................ 14 FINDINGMODELNUMBER This Operator's Manual is an important part of your new Yard Vacuum. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below. The information on the model plate is very important if you need help from our Customer Support Department or an authorized dealer. You can locate the model number by looking down at the rear of the Yard Vacuum. A sample model plate is explained below. For future reference, please copy the model number and the serial number of the equipment in the space below. Copy the model number here: O11"_.mll"ll'" mm_az,w_-_mm.m www.trovbiltcom -- • TROY-BILT LLC P.O. BOX 361131 CLEVELAND,OH 44136 330-558-7220 866-840-6483) Copy the serial number here: ENGINEINFORMATION The engine manufacturer is responsible for all engine-related issues with regards to performance, powerrating, specifications, warranty and service. Please refer to the engine manufacturer's Owner's/Operator's Manual packed separately with your unit for more information. CALLINGCUSTOMER SUPPORT If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, please call the Customer Support Department. Call 1- (330) 558-7220 or 1- (866)-840-6483 to reach a Customer Support representative. Please have your unit's model number and serial number ready when you call. See previous section to locate this information. You will be asked to enter the serial number in order to process your call. SECTION1: IMPORTANTSAFEOPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning. _ components contain or emit chemicals known to State of to cause cancer WARNING: Engine Exhaust, some of its constituents, andCalifornia certain vehicle and birth defects or other reproductive harm. DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. TRAINING 1. 2. 3. 4. 5. 6. 7. 8. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts. Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly. Never allow children under 16 years old to operate this machine. Children 16 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent. Never allow adults to operate this machine without proper instruction. Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. Never attempt to unclog either the feed intake or discharge opening, remove or empty vacuum bag, or inspect and repair the machine while the engine is running. Shut the engine off and wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine. PREPARATION 1. Thoroughly inspect the area where the equipment is to be used. Remove all rocks, bottles, cans, or other foreign objects which could be picked up or thrown and cause personal injury or damage to the machine. 2, 3, 4, 5, 6. Always wear safety glasses or safety goggles during operation or while performing an adjustment or repair, to protect eyes. Thrown objects which ricochet can cause serious injury to the eyes. Wear sturdy, rough-soled work shoes and closefitting slacks and shirts. Loose fitting clothes or jewelry can be caught in movable parts. Never operate this machine in bare feet or sandals. Wear leather work gloves when feeding material in the chipper chute. Before starting, check all bolts and screws for proper tightness to be sure the machine is in safe working condition. Also, visually inspect machine for any damage at frequent intervals. Maintain or replace safety and instructions labels, as necessary. To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately. a. Use only an approved gasoline container. b. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. c. Never fuel machine indoors. d. e. f. g. h. Never remove gas cap or add fuel while the engine is hot or running. Allow engine to cool at least two minutes before refueling. Never over fill fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion. Replace gasoline cap and tighten securely. If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes before starting the engine. i. Neverstorethemachineor fuelcontainer insidewherethereis anopenflame,spark, or pilotlight(e.g.furnace,waterheater, spaceheater,clothesdryer,etc.) j. Toreducea firehazard,keepmachinefree ofgrass,leaves,or otherdebrisbuild-up. Cleanupoilorfuelspillageandremoveany fuelsoakeddebris. k. Allowmachine tocoolatleast5 minutes beforestoring. 9. 10. 11. 12. OPERATION 1. 2. 3. 4. 5. 6. 7. 8. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris. Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine. If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps: a. Inspect fordamage. b. Repair or replace any damaged parts. c. Check for any loose parts and tighten to assure continued safe operation. Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening. Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result. Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris. Never operate without vacuum bag and discharge chute properly attached to the machine. Never empty or change vacuum bag while the engine is running. Zippered end of vacuum bag must be kept closed at all times during operation. 13. 14. 15. 16. Never operate without either the inlet nozzle or optional hose attachment properly attached to the machine. Never attempt to attach or change either attachment while the engine is running. Keep all guards, deflectors and safety devices in place and operating properly. Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries. Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Do not operate this machine on a gravel surface. Do not operate this machine while under the influence of alcohol or drugs. Muffler and engine become hot and can cause a burn. Do not touch. Never pick up or carry machine while the engine is running. MAINTENANCE ANDSTORAGE 1. Never tamper with safety devices. Check their proper operation regularly. 2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed. 3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. 4. Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine. 5. Maintain or replace safety and instruction labels, as necessary. 6. Follow this manual for safe loading, unloading, transporting, and storage of this machine. 7. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc. 8. Always refer to the operator's manual for proper instructions on off-season storage. 9. If the fuel tank has to be drained, do this outdoors. 10. Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment. ,_ understand the warnings and instructions in this manual and of onthis the power machine. WARNINGand -follow YOUR RESPONSIBILITY: Restrict the use machine to persons who read, ,' ,,," 0i_ '_%. ,,.... _'_ /.... SECTION2: ASSEMBLING YOURYARDVACUUM IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine. NOTE: Reference to right or left hand side of the Yard Vacuum is observed from the operating position. Blower Chute_ Upper Handle_ Wing Nuts Rope Guide_ RemovingUnitFromCarton • • • • Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton. Remove loose parts if included with unit (i.e., operator's manual, etc.) Cut along corners, lay carton down flat, and remove packing material. Roll or slide unit out of carton and check carton i wer thoroughly for loose parts. andre LoosePartsIn Carton(SeeFigure1) • • • • Handle Assembly Bag Blower Chute (If Equipped) Hose Assembly se sembly f_\\ /Bag / Disconnecting SparkPlugWire Before setting up your Yard Vacuum, disconnect the spark plug wire from the spark plug and ground to a stud on the engine. \ Figure 1 AttachingTheHandle • • • • • Unfold the upper handle until it aligns with the lower handle. Secure the two handles by tightening the wing nuts (carriage bolts must be seated properly into the handle). See Figure 1 Remove the hairpin clips from the handle brackets on the Yard Vacuum and remove the carriage bolts and wing nuts from the lower handle. See Figure 2. Place the bottom holes in lower handle over pins on handle brackets and secure with hairpin clips. Insert carriage bolts through upper hole in lower handle from the outside and secure with wing nuts. Hose Spring Pin Figure 3 Wing Nuts AttachingTheBag • • • • Figure 2 Grasp bag handle with one hand and slide locking rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as leverage when sliding the locking rod. See Figure 4. Slip bag over the rim of the discharge opening and release locking rod to secure bag in place. Place the straps on the bag over the lower handle, hooking them on the studs. Snap bag clip to the top of the lower handle. NOTE: The safety switch button attached to the mounting bracket must be fully depressed by the front tab on the bag handle when securing the bag or the engine will not start. Loosen the wing nut that secures the rope guide to the right side of upper handle. Pull the starter rope out of the engine slowly and slip the starter rope into the rope guide. Tighten the wing nut. AttachingTheHoseAssembly • • • • • Slide hose adapter of hose assembly into the base adapter located on the left front of the Yard Vacuum. See Figure 3. Pull spring loaded pin out on the base and align pin with the first hole in the hose adapter. Release the pin to lock the hose in place. Connect the hose handle near nozzle end of hose to the side bracket on the upper handle. Refer to Figure 6. Snap hose handle to the lower handle bracket to secure in place and lay hose tubing on side bracket hanger next to chipper chute. Refer to Figure 6. Figure 4 AttachingTheBlowerChute(IfEquipped) • • • Blower _Chute Grasp blower chute with one hand and slide locking rod on mounting bracket with other hand toward engine. Use end of mounting bracket as leverage when sliding the locking rod. See Figure 5. Slip blower chute over rim of the discharge opening and release locking rod to secure chute in place. Make sure the safety switch button is fully depressed by the front tab on the blower chute. Raise the nozzle height to the highest setting when using the blower chute. Refer to nozzle height adjustment in the OPERATION section. Front Tab Figure5 SECTION3: KNOWYOURYARDVACUUM Starter Handle \ \ Handle \ \ Handle Vac Handle Hose Assembly Blower Chute Nozzle Figure6 Read this operator's manual and safety rules before operating your Yard Vacuum. Compare the illustrations in Figure 6 with your unit to familiarize yourself with the location of various controls and adjustments. WARNING: The operation of any Yard Vacuum can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses, provided with the Yard Vacuum, for operating this equipment or while performing any adjustments or repairs on it. Starter Handle The starter handle is attached to the right upper handle. Stand behind unit and pull the starter handle to start engine. Bag Collects shredded material fed through the chipper chute or vacuumed through the nozzle or hose. Bag Handle Used to grasp bag in order to assist in attaching, removing, and emptying bag. Chipper Chute HoseHandle Allow twigs and small branches up to 1 1/2" in diameter to be fed into the impeller for chipping. Used to guide hose assembly when vacuuming. Blower Chute(if Equipped) When attached to unit the blower chute is used to blow or scatter yard waste such as leaves, pine needles, or small twigs across yard. The nozzle/hose vac handle is located on top of the nozzle and it is used to regulate the vacuum between the nozzle and the hose assembly. Nozzle Height AdjustmentLever Used to adjust the nozzle ground clearance ranging approximately 5/8" to 4 1/8". The throttle control lever is located on the engine. It controls the engine's speed and stops the engine. See separate engine manual packed with unit for details. Nozzle EngineControls See the separate engine manual for the location and function of the controls on the engine. Yard waste such as leaves or pine needles can be vacuumed up through the nozzle for shredding. HoseAssembly Used as an alternative to the nozzle to vacuum yard waste such as leaves or pine needles in hard to reach places. Nozzle/HoseVac Handle Throttle ControlLever (Not Shown) StoppingEngine • • Move throttle control lever to STOP or OFF position. Disconnect spark plug wire from spark plug and ground against the engine. SECTION4: OPERATING YOURYARDVACUUM WARNING: The operation of the Yard Vacuum can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses provided with this unit or eye shields before chipping or blowing and while performing any adjustments or repairs. GasAndOilFill-Up Service the engine with gasoline and oil as instructed in the separate engine manual packed with your Yard Vacuum. Read instructions carefully. WARNING: Never fill fuel tank indoors with engine running or until the engine has been allowed to cool for at least two minutes after running. • • • • • _r_ 411 StartingEngine • • • Attach spark plug wire to spark plug. Make certain the metal cap on the end of the spark plug is fastened securely over the metal tip on the spark plug. Make sure safety switch wire is connected to engine and properly grounded. Engines with choke lever: Move choke lever on engine to CHOKE position. (A warm engine may not require choking). Engines with primer: Prime engine as instructed in separate engine manual. The throttle control is located on the engine. Move engine throttle control lever to FAST or ON position. Stand behind unit, grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly. Repeat previous steps until engine fires. When engine starts, move choke control (if equipped) gradually to RUN position. WARNING: Never run the engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. ToEmptyBag • • • • Unhook bag straps from the lower handle and unsnap bag clip from the top of lower handle. See Figure 7. Grasp bag handle with one hand and pull lock rod on mounting bracket with other hand toward engine to release. Remove bag from rim of the discharge opening. Refer to Figure 4. Twist the two buttons on the back of the bag to unlock and empty contents. See Figure 7. • • • Holdbaghandleandbagclipwhileemptyingthe contents. Compress bagopeningandfoldinnerflapover opening. Foldouterflapoverinnerflapandinsertbuttonson thebagthroughmetaloutlets. Twistthebuttonsto lockbag. Nozzle/Hose Vac Handle (Top Position) 3u_ons Bag Inner Flap Spring Loaded Pin (First Hole) Bag Handle J Outer Flap_ Figure 8 IMPORTANT: The flail screen is located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in SECTION 5: MAINTAINING YOUR YARD VACUUM. For best performance, it is also important to keep the chipper blade sharp. Figure 7 ToRemoveBlowerChute • • Grasp blower chute with one hand and pull lock rod on mounting bracket with other hand toward engine to release. Refer to Figure 5. Remove blower chute from rim of the discharge opening. Usingthe NozzleVacuum • Place nozzle/hose vac handle in the top position on the nozzle to vacuum through nozzle. See Figure 8. • The spring loaded pin must be in the first hole of the hose adapter to operate the nozzle vac. • Place both hands on top of upper handle to push unit over yard waste. Yard waste such as leaves and pine needles can be vacuumed up through the nozzle for shredding. After material has been shredded by the flail blades on the impeller assembly, it will be discharged into catcher bag or through blower chute. Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e. branches, leaves, twigs, etc.) Avoid fibrous plants such as tomato vines until they are thoroughly dried out. Materials such as stalks or heavy branches up to 1 1/2" in diameter may be fed into the chipper chute. adjustments without first stopping engine WARNING: Do not at any time make any and disconnecting spark plug wire. Usingthe HoseAssembly • • • Place nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assembly. See Figure 9. The spring loaded pin must be in the second hole of the hose adapter to operate the hose assembly. Unhook the hose from upper handle bracket and grasp the hose handle to guide while vacuuming yard waste such as leaves or pine needles in hard to reach places. Nozzle/Hose Vac Handle (Bottom Position) / Spring Loaded Pin (Second Hole) Figure 9 NozzleHeightAdjustment The nozzle can be adjusted to any six positions, ranging from 5/8" to 4 1/8" ground clearance. The nozzle height has to be adjusted according to the conditions. Move the height adjustment levers forward or backward to adjust the nozzle upwards or downwards. See Figure 10. NOTE: In general, raise the nozzle height to vacuum a thick layer of lea ves or to operate with the blower chute and lower the nozzle height for smoother surfaces. Nozzle Height Adjustment Lever Nozzle j Figure 10 SECTION5: MAINTAININGYOURYARDVACUUM CustomerResponsibilities o.o,oO.J! MAINTENANCE SCHEDULE tO D Lubricate Wheels Lubricate Nozzle Levers O Lubricate Locking Rod _o,O _o_ &o_ e_ SERVICE ._e _o DATES Q_ Lubricate Nozzle/Hose Handle Check Chipper Blade Change Oil Check Air Filter Z Clean Engine Check Spark Plug Locking Rod: Lubricate the locking rod with light oil to ease the application of attaching on or removing bag or blower chute. Refer to Figure 6. Nozzle/Hose Vac Handle: Lubricate the nozzle/hose disconnect spark plug WARNING: Always stop wire engine before and cleaning, lubricating or doing any kind of maintenance on your machine. vac handle on top of nozzle once a season with light oil. Refer to Figure 6. Lubrication Wheels: Lubricate each wheel shoulder screw once a Engine: Follow the separate engine manual packed with you unit for lubrication instructions. season with light oil. Refer to Figure 6. Nozzle height adjustment levers: Lubricate the pivot points of the nozzle height adjustment levers once a season with light oil. Refer to Figure 6. 10 Maintenance Engine Refer to the separate engine manual for all engine maintenance instructions. • • • Check engine oil level before each use as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully. Clean air cleaner every 25 hours under normal conditions or once a season. Clean every few hours under extremely dusty conditions. To service the air cleaner, refer to the separate engine manual packed with your unit. The spark plug should be cleaned and the gap reset once a season. Check engine manual for correct plug type and gap specifications. Remove Hex Screw Figure 12 SharpeningOrReplacingChipperBlade RemovingTheFlailScreen Because the engine on this unit has a tapered crankshaft, a special impeller tool (part number 7530900) is required to remove the impeller assembly. For further assistance, contact your local service dealer. If the discharge area becomes clogged, remove the flail screen and clean area as follows: • • • Stop the engine and make certain the Yard Vacuum has come to a complete stop. Disconnect spark plug wire from spark plug and ground against the engine. Remove the bag or blower chute from the unit as instructed in the OPERATION section to obtain access to flail screen. See Figure 11. NOTE: When tipping the unit, empty the fuel tank and keep spark plug side up. • • • Disconnect the spark plug wire and ground it away from the spark plug. Remove the front hubcaps, lock nuts, front wheels, and wave washers that attach to the pivot arm assemblies. See Figure 13. Remove the shoulder screws and bell washers that go through the pivot arms and height bracket adjusters to the front support brace. i Pivot Arm Assembly Bell Washer Wave Washer Hubcap Figure 11 / Remove hex screw on right side of unit that attaches to the fail screen. It may be necessary to remove the hose bracket hanger to get access to the hex screw. See Figure 12. Remove hex screw and flat washer on top of rear housing mounting bracket and the lock nut that secures flail screen. See Figure 11. Remove and clean the screen by scraping or washing with water. Reinstall the flail screen. Height Adju_ment Bracket Shoulder Screw Lock Nut _ Figure 13 Remove the three screws on the upper housing that secure the nozzle cover and the nine screws that secure the lower housing to the upper housing. See Figure 14. 11 • Housing • Screws\ • • • • Lower Housing Screws • Screws Apply lubricant to the threads of impeller removal tool and then thread the tool into the crankshaft. Stop when the impeller assembly can move on the crankshaft. Remove the impeller assembly from the crankshaft. Unthread the impeller removal tool from the impeller assembly. Remove the blade using a 3/16" allen wrench on the outside of the blade and 1/2" wrench on the impeller assembly. Replace or sharpen chipper blade. When sharpening blade, protect hands by using gloves and follow the original angle of grind. Reassemble by performing the previous steps in reverse order. Tighten blade screws to 210-250 in-lbs. Tighten impeller bolt to 375-425 in-tbs. NOTE: Make certain chipper blade is reassembled with the sharp edge facing upward. See Figure 16. Figure 14 Remove lock nut that secures flail screen to the lower housing. The flail screen does not have to be removed. Refer to Figure 11. Remove the hex boll lock washer, and flat washer that secure the impeller assembly to the crankshaft. See Figure 15. Flail Chipper Blade _ _.._ _l_ _ Upper _lmpeller Assembly Figure 16 Impeller JAssembly StoringYourYardVacuum Hex Bolt Lock Washer Flat Washer _Flail Blade BOTTOM VIEW Figure 15 12 • • • Clean the equipment thoroughly. Wipe equipment with a oiled rag to prevent rust. Refer to engine manual for correct engine storage instructions. • Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. SECTION6: TROUBLESHOOTING Problem Engine fails to start Cause 1. 2. 3. Connect wire to spark plug. Fill tank with clean, fresh gasoline. Move throttle lever to FAST position. 4. 5. 6. Spark plug wire disconnected. Fuel tank empty or stale fuel. Throttle control lever not in correct starting position. (If Equipped) Choke not in CHOKE position. Blocked fuel line. Faulty spark plug. 4. 5. 6. Move choke to CHOKE position. Clean fuel line. Clean, adjust gap, or replace. 1. 2. Spark plug wire loose. Unit running on CHOKE. 1. 2. 3. Blocked fuel line or stale fuel. 3. 4. 5. 6. Water or dirt in fuel system. Dirty air cleaner. Carburetor out of adjustment. 4. 5. 6. Connect and tighten spark plug wire. Move choke lever (if equipped) to OFF position. Clean fuel line; fill tank with clean, fresh gasoline Drain fuel tank. Refill with fresh fuel. Clean or replace air cleaner. See authorized service dealer. Too much vibration 1. Loose parts or damaged impeller. 1. See authorized service dealer. Engine overheats 1. 2. 3. Engine oil level low. Dirty air cleaner. Carburetor not adjusted properly. 1. 2. 3. Fill crankcase with proper oil. Clean or replace air cleaner. See authorized service dealer. Occasional skip (hesitates at high speed 1. Spark plug gap too close. 1. Adjust gap to .030". Unit does not discharge 1. Discharge chute clogged. 1. 2. Foreign object lodged in impeller. 2. 3. 4. Lowengine RPM Vacuum bag is full. 3. 4. Stop engine immediately and disconnect spark plug wire. Clean flail screen and inside of discharge opening Stop engine and disconnect spark plug wire. Remove lodged object. Always run engine at full throttle. Empty bag. 1. 2. Low engine RPM. Chipper blade dull. 1. 2. Engine runs erratic Rate of discharge slows considerably or composition of discharged material changes. 1. 2. 3. Remedy Always run engine at full throttle. Replace chipper blade or see your authorized service dealer. NOTE: For repairs beyond the minor adjustments listed above, contacl zour nearest authorized service dealer. 13 Model24A-O60F063 17 5_ _o Y 13 12 7 15 16__ 22 48 33 47 46 31 t 30 45 49 _ ) 50_ 42 40 11 39 52 _. / J f / _J 54 14 34 35 Model24A-O60F063 Ref. No. Part No. Ref. No. Part Description Part No. Part Description 1. 712-0161 Hex Lock Nut #10 - 24 29. 710-3025 2. 749-0438D 3. 720-0279 Upper Handle Knob 30. 31. 710-0502A 710-0751 4. 712-3004A Flange Lock Nut 5/16-18 32. 731-2484 Hose Base Adapter 5. 710-1205 Eye Bolt 33. 716-0104 E Ring .500 Dia 6. 781-1056 Upper Handle Bracket 34. 732-3035 7. 710-0528 8. 720-0314 Hex Cap Screw 5/16-18 x 1.25 Handle Knob 5/16-18 35. 36. 711-1571 736-3020 Compression Clevis Pin 9. 710-1174 710-0604A 37. 38. 710-0969 710-0425 Screw #12-16 x 1.0 11. Carriage Bolt Hex Washer Screw 5/16-18 x.625 12. 681-0174 Lower Handle Bracket 39. 781-1042 Upper Housing 13. 749-0907B Lower Handle 40. 726-0454 U-Clip Lock Nut 5/16-18 14. 711-1293 Studs 41. 710-3008 Hex Cap Screw 5/16-18 x.75 15. 710-0703 Carriage Screw 1/4-20 x.75 42. 681-0122 16. 712-0397 17. 751B282175 Wing Nut 1/4-20 Shroud 43. 44. 738-1167 736-0371 Chipper Chute Assembly Stud 5/16-18 x .56 18. 725-1700 Switch Cover 45. 781-1058 Hose Bracket Hanger 19. 725-3166 Safety Switch 46. 712-3027 Hex Flange Nut 1/4-20 20. 731-1613 21. 710-0224 Safety Switch Cover Hex Washer Screw #10-16 x.50 47. 48. 748-0457 731-2478 Spacer Hose Nozzle 22. 629-0920 Wire Harness 49. 710-3288 Hex Cap Screw 1/4-20 x 2.625 23. 714-0104 Cotter Pin 50. 723-0295 24. 736-0264 Flat Washer.330 ID x.630 OD 51. 749-1270 Adjustment Clamp Nozzle Handle 25. 732-0962 Compression 52. 764-0648 Vacuum Hose 26. 781-0778A 747-1153 53. 54. 07071 731-2292 Handle Grip 27. Mounting Bracket Lock Rod 28. 710-3195 Hex Cap Screw 5/16-18 x 4.5 55. 736-0607 Spring 15 Hex Cap Screw 5/16-18 x.625 Hex Washer Screw 3/8-16 x 1.25 Hex Cap Screw 1/4-20 x .620 Spring Flat Washer ..271 ID x .630 OD Machine Screw #10 - 24 x .625 Flat Washer .343 ID x .880 OD Hose Adapter External L-Washer 5/16 Model24A-O60F063 58 1 59 2 3 4 5 60 6 7_ 14 "6 23 17 _18 _21 r _.dr_ _ _ 37 5 _ _22217 . q 41 44 43 38 __34 :40 46 49 _ \24 45 35 42 53 51 42 39 44 48 50 52 '54 16 55 Model24A-O60F063 Ref. No. Part No. Ref. No. Part Description 1. 664-0095 Bag Assembly 2. 3. 681-0154 710-1054 Screen Assembly Hex Screw 5/16-24 x 1.0 4. 781-0490 5. Part No. Part Description 32. 732-1150 33. 34. 731-2294 711-1582 Chipper Blade 35. 781-0725A Front Wheel Support Brace 681-0152 Impeller Assembly 36. Rear Wheel Support Brace 6. 781-0735 37. 7. 719-0329 Pin Clip Flail Blade 781-0777 681-0155 8. 9. 715-0166 711-1401 Spiral Pin 10. 736-0247 Clevis Pin Flat Washer.375 ID x 1.25 OD 11. 736-0217 Lock Washer 3/8 12. 13. 710-0818 710-3038 Hex Cap Screw 3/8-24 x 2.0 Hex Cap Screw 5/16-18 x .875 14. 781-0721A 15. 712-3004A 16. 712-3027 17. 736-0142 Hex Flange Nut 1/4-20 Flat Washer .281 ID x .50 OD 18. 714-0225 Cotter Pin 19. 711-1560 20. 731-2293 21. 781-1064 22. 732-1156 23. 726-0106 24. 711-1551 25. 26. 712-0161 736-0400 Hex Lock Nut #10-24 Flat Washer .194 ID x .62 OD 56. 27. 731-2485 57_ 58. Thrust Washer .375 ID x .70 OD 710-1156 Nozzle Door Lever Hex Screw #10-24 x 1.25 736-0314 28, OEM-290-012 Blower Chute (If Equipped) 29. 30, 750-1294 732-3118 Shoulder Spacer 59. 764-0632 Bag Extension Spring 60. 631-0083 Chute Assembly 31. 732-1151 Torsion Spring LH . Torsion Spring RH Nozzle Door Rod .25 x 1.25 Lg 681-0156 Handle Bracket Ass"y LH Handle Brkt Assay RH (Not Shown) 38. 714-0104 Cotter Pin 39. 40. 710-3025 Hex Cap Screw 5/16-18 x.625 Bell Washer.401 ID x.870 OD 41. 736-0105 734-04007 Wheel 9 x 2 42. 736-0232 Wave Washer .531 ID x .781 OD 43. 738-1015 Shoulder Screw 3/8-16 44. 45. 46. 731-0981A Hubcap 781-0785 738-1185 Height Adjustment Bracket Stud 5/16-18.56 x .75 47. 741-0751 Height Adjustment Bearing 48. 682-0113 Pivot Rod Nozzle 49. 50. 720-0426 732-1026 Pivot Arm Assembly Height Adjustment Knob Base Adapter Door Torsion Spring 51. 52. 736-0741 738-1173 Cap Speed Nut 1/4 Pivot Red 53. 54. 734-2004A 712-0431 55. 726-0453 712-0158 Lower Housing Flange Lock Nut 5/16-18 • . 17 Spring Lever Bell Washer .760 ID x .25 OD Shoulder Screw .750 ID x .625 OD Wheel 8 x 2 Flange Lock Nut 3/8-16 Lock Nut 3/8-16 Hex Lock Nut 5/16-18 Notes 18 19 MANUFACTURER'S LIMITED WARRANTY TRilI RILT The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. Troy-Bilt LLC warrants this product against defects for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator's Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment not approved by Troy-BiB LLC for use with the product(s) covered by this manual will void your warranty as to any resulting damage. Normal wear parts or components thereof are subject to separate terms as follows: All normal wear parts or component failures will be covered on the product for a period of 90 days regardless of cause. After 90 days, but within the two year period, normal wear part failures will be covered ONLY IF caused by defects in materials or workmanship of OTHER component parts. Normal wear parts and components include, but are not limited to: batteries, belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow thrower skid shoes, shave plates, auger spiral rubber, and tires. ROW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE, through your local authorized service dealer. To locate the dealer in your area, check your Yellow Pages, or contact Troy-Bilt LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call 1866-840-6483 or 1-330-558-7220, or log on to our Web site at www.t roybilt.com. This limited warranty does not provide coverage in the following cases: a. b. c. The engine or component parts thereof. These items carry a separate manufacturer's warranty. Refer to applicable manufacturer's warranty for terms and conditions. Log splitter pumps, valves, and cylinders have a separate one year warranty. Routine maintenance items such as lubricants, filters, blade sharpening, tune-ups, brake adjustments, clutch adjustments, deck adjustments, and normal deterioration of the exterior finish due to use or exposure. d. e. f. g. FOR: " Troy-Bilt LLC does not extend any warranty for products sold or exported outside of the United States, its possesions and territories, except those sold through Troy-Bilt LLC's authorized channels of export distribution. Parts that are not genuine Troy-Bilt parts are not covered by this warranty. Service completed by someone other than an authorized service dealer is not covered by this warranty. Transportation charges and service calls are not covered. No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty, whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product, shall bind Troy-Biit LLC. During the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above. The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. TroyBiit LLC shall not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the misuse or inability to use the product. This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift. HOW STATE LAW RELATES TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Troy-Bilt LLC, P.O. BOX361131CLEVELAND,OHIO44136-0019; Phone:1-866-840-6483,1-330-558-7220
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 20 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Aug 14 18:19:44 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools