True Fitness 350 750 Users Manual Treadmill Service

90c true_fitness_350-750_treadmills_om

350750 397b8feb-b124-4e43-a333-8d182307dfe4 True Fitness Treadmill 350-750 User Guide |

2015-02-03

: True-Fitness True-Fitness-350-750-Users-Manual-460460 true-fitness-350-750-users-manual-460460 true-fitness pdf

Open the PDF directly: View PDF PDF.
Page Count: 83

True Fitness Service
Manual
Treadmills
Models 350-750
True fitness technology, Inc. makes no representations or warranties regarding the
contents of this manual. We reserve the right to revise this document at any time or
to make changes to the product described within it without notice or obligation to
notify any person of such revisions or changes.
© 2004, True Fitness, Inc. All rights reserved. Printed in the United States of
America.
865 Hoff Road. O’Fallon, MO 63366. 1-800-426-6570. Fax 636-272-3026.
www.truefitness.com
Revision 9/2004
Treadmill Preventative Maintenance
Checklist
Run calibration or run a manual program and
watch and listen for anything out of the ordinary.
Perform a push off test (page T-7) to check for
proper lubrication. If excessive friction is found
and lubrication doesn’t correct the problem
perform the amp draw test (page T1-2)
Inspect the belt surfaces, topside should still have
texture for grip, bottom should be porous fabric-
not glazed, smooth or hard.
Inspect deck surface, should be free of scratches,
abrasions or blistering.
Listen for excessive bearing noise, from a
standing position, in the front and rear roller and
motor.
Check for front roller/belt slippage and belt
tension adjustment. Look for slippage on drive
pulley.
Inspect/ adjust tracking of belt.
Vacuum out motor area, being careful not to
damage PWM.
Inspect drive belt for wear and cracking.
Wipe down machine- leave it in better condition
than you found it.
True Fitness
Treadmill Service
Manual
START
Symptom guide
Calibration Procedures
Diagnostic Procedures
Test Procedures
Wiring Diagrams
Part Manuals
Page 1
SYMPTOM GUIDE
Error Code Definitions . . . . . . . . . . . . . . . . . . . . . . . . Page 3, 4
No Belt Movement . . . . . . . . . . . . . . . . . . . . . . . . Page 5, 6
Tread Belt Stops During Workout . . . . . . . . . . . . . . . . Page 7
Heart Rate Not Working / Erratic Readings . . . . . . . . Page 8
Elevation Not Functional . . . . . . . . . . . . . . . . . . . . .. . Page 9
Speed Fluctuation: E2 Cal . . . . . . . . . . . . . . . . . . . . . . Page 10
Speed Fluctuation: S4, E5, E2
E3: EPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . Page 11
No Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12
Circuit Breaker Trips at Start Up . . . . . . . . . . . . . .. . Page 13
Soft Select Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . Page 14, 15
Calibration Procedures . . . . . . . . . . . . . . . . . . . . . . . . Page 16
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. Page 17
Page 2
Symptom Probable Cause Corrective Action Recommended Tools
ERROR
MESSAGES:
S1 L LUBE
S2 C CLEAN
S3 M MOTOR
E5 S SPEED
SENSOR
E1 S STALL
E1 I INCLINE
E1 R RANGE
Indicates that the
accumulated distance
is such that the deck
needs to be lubed
Indicates that the
accumulated distance
is such that the
machine needs to be
cleaned.
Indicates that the
accumulated time on
the treadmill is such
that the motor brushes
need to be
changed/checked.
Cannot read speed
sensor
Incline reading not
changing when
commanded
Incline reading has
changed without the
incline being
commanded.
Maximum or
minimum elevation
out of calibrated
ranges
• Lube deck with True Fitness liquid
silicone lubricant. Inspect wax bar
assembly on commercial models, if
worn to less that ¼ inch in thickness-
replace wax bar.
• Remove motor cover and vacuum dust
from area. Wipe down the exposed area
of the deck beside the straddle covers
with a clean, dry cloth.
• Check/Replace motor brushes as
needed.
• Reset timer.
• Perform Speed Sensor Test page 21
• See Elevation Not Functional page 9.
• See Elevation Not Functional page 9.
• See Elevation Not Functional page 9.
Liquid silicone single
use pack
Liquid Silicone
Applicator.
Vacuum
Shop towel
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 3
Symptom Probable Cause Corrective Action Recommended Tools
ERROR
MESSAGES:
(cont’d)
E2 O
OVERSPEED
E2 C
CALIBRATE
E3 E EEPROM
E2 R
RECALIBRATE
Belt speed ramping
too fast.
Micro-controller
cannot adjust belt
speed to target.
Software error during
treadmill startup
diagnostics.
Treadmill has lost
calibration settings.
Perform Amp Draw Test – Page 20.
Perform Belt / Deck Wear Test – Page 24.
Calibrate Treadmill – Page 16.
See appropriate Symptom Guide – pages 10-11.
Restart Treadmill, if error persists- replace
control panel.
Recalibrate Treadmill – Page 16.
(If unit loses programs- replace control panel)
Multi-meter
Phillips head
screwdriver
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
Page 4
Symptom Probable Cause Corrective Action Recommended Tools
NO BELT
MOVEMENT
Treadmill in need of
calibration.
Missing command to
PWM.
Missing/incorrect
voltage to motor.
Damaged motor.
• Run calibration. (page 16)
--------
• Is PWM light blinking/ illuminated
when fast button is pushed?
NO- Check continuity on wire harness, if
harness has continuity breaks replace the
harness. If harness has continuity- replace
the upper panel. Refer to wiring harness
diagram for your model.
YES- move on to next step, wire harness and
control panel are OK.
--------
• With treadmill in calibration mode
(page 16)
• Set speed at 4 MPH
• Check VDC across MTR 1 and MTR 2
with the motor leads connected to the
motor the voltage should measure 10
VDC for every 1 MPH.
• If voltage is missing or low- Replace
PWM.
• If voltage is greater than 20 VDC/MPH
motor may have open windings.
--------
• With PWM LED Blinking/ Illuminated-
move the tread belt with your foot to see
if motor begins to move on its own.
• If motor begins to move, inspect the
condition of the brushes and the
commutator.
• If brushes are bad- replace brushes
• If motor doesn’t turn or has a damaged
com segment- replace motor.
Continue on next page…
Multi-meter
PWM / Motor test
cables
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 5
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Symptom Probable Cause Corrective Action Recommended Tools
NO BELT
MOVEMENT
(cont’d)
Motor turns but belt
does not.
Belt cannot be
moved manually-
foreign object under
belt.
• Check belt tension.
• Set belt tension to 1/8-inch deflection or
correct tension can be verified by
twisting the belt almost to a 90-degree
position.
--------
• Remove foreign object.
Perform the Amp Draw Test (page 20) to check
for excessive amp draw damage
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
Page 6
Symptom Probable Cause Corrective Action Recommended Tools
TREADBELT
STOPS
DURING
WORKOUT
Error Code
displays:
Go to page 3 &
Page 4.
Loose safety key
connection
Belt movement issue
Worn Deck / Belt
Occurs when making
changes to speed or
elevation
Overloaded house
circuit
Continuity,
connection to motor
Tread belt not
centered or
obstructed
• Check safety key to ensure that it is
seating properly.
• Check connection sensitivity.
--------
• If treadmill will not reset with cycling
the power go to NO BELT
MOVEMENT (pages 5 & 6)
--------
• Perform Belt / Deck Wear Test
(page 24).
• Perform Amp Draw Test (page 20).
• Apply silicone.
• Replace Deck and Belt.
--------
• May be related to electro static
discharge. Contact Technical support
for assistance.
--------
• Verify the treadmill is on a dedicated
circuit with at least a 15 amp breaker
• Have customer supply a dedicated
circuit
--------
• Reconnect or replace motor wires or
connectors
--------
• Tension tread belt (page 22)
• Center tread belt
• Remove obstruction
Liquid silicone
single use pack
Liquid silicone
Applicator
Multi-meter
Socket set
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 7
Symptom Probable Cause Corrective Action Recommended Tools
HEART RATE
NOT
WORKING /
ERRATIC
READINGS
Incorrect power
source
Improper treadmill
grounding
Improper heart rate
receiver mount
Defective Chest
Strap
Defective receiver
Radio Frequency
Interference
•
Verify that the treadmill is connected to
a dedicated line, 15-amp circuit, and not
on an extension cord.
• Move to proper outlet.
• Test 110 VAC outlet for proper ground
--------
• Proper grounding is vitally important.
• Ensure that the pedestal wire harness
ground lead is secure
--------
• Ensure that the HR receiver is not
touching metal and is mounted with the
wires in a vertical position with the blue
receiver facing the runner
--------
• Does the receiver pick up a signal from
the HR simulator?
• If yes, replace chest strap
--------
• Does the heart rate LED on the control
panel blink? If not then replace the
receiver.
--------
• Locate RF sources and use process of
elimination. Common sources of RF
interference are: Invisible fences for
pets; wireless networks; cordless
phones, Cell phones, radios, home
security sensors, etc.
Multi-meter
Double sided tape
Heart rate simulator
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
Page 8
Symptom Probable Cause Corrective Action Recommended Tools
ELEVATION
NOT
FUNCTIONAL
( E1 ERROR)
Improper grounding
/ Calibration
(May cause unit to
drift up & down
without command)
Unit is stuck at full
incline
Defective Start
Capacitor
Defective PWM
•
Test 110VAC outlet for proper
grounding
• If unit has not been calibrated –
calibrate
• Ensure that incline cables are secure on
PWM
--------
• Verify the lower limit switch is properly
connected to the PWM
• Remove the LLS wire from the PWM
and short the two posts of the connector
together with an alligator clip. Cycle the
power. If the treadmill lowers itself
then replace the lower limit switch.
• Perform Incline potentiometer
calibration procedure (page 16)
• If incline nut is stripped- replace incline
nut
--------
• Do Up/Down command LED’s light?
• If No- skip to defective PWM section.
• If yes- does motor hum with no
movement?
• If yes- check the leads to the capacitor
for breaks, if no breaks- replace
capacitor.
• If No- replace PWM.
--------
• If no Up/Down LED’s light check
continuity on data cables.
• If cables are good- replace Upper Panel.
• If cables bad- Replace data cables.
Multi-meter
Alligator clip
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 9
Symptom Probable Cause Corrective Action Recommended Tools
SPEED
FLUCTUATION
E2: CAL
Speed Fluctuation
(Due to high friction)
Speed Fluctuation
(Due to Voltage
fluctuation)
Bad Data Feedback
Incorrect Speed
Sensor Gap
• Perform Push Off Test (page 24)
• Perform Amp Draw Test (page 20)
--------
• Check Line voltage for fluctuations.
• Have customer take corrective action.
--------
• Verify tach feedback accuracy through
out the speed range.
• If inaccurate perform speed sensor test
(page 21)
--------
• Verify correct Speed sensor Gap.
• Gap should be equal to the thickness of
(3) credit cards pressed together
(approximately 1/8 to ¼ inch)
------
Multi-meter
Socket Set
Silicone Lubrication
Packet
Silicone Lubrication
Applicator
Note: All
trouble shootin
g
should be
performed in
Calibration
Mode:
See SG-12
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
Page 10
Symptom Probable Cause Corrective Action Recommended Tools
SPEED
FLUCTUATION
S4: Sensor
E5: Speed Sensor
E2: Overspeed
E3: EPROM Error
No Belt Movement
No/Intermittent
Tach Feedback
Overspeed Error
E3: EPROM Error
Software error
during treadmill
startup
• Go to page 5, 6.
--------
• Enter Calibration mode (page 16)
• Verify speed feedback in speed display
through out the speed range. [Speed
display should never show 0 mph when
belt is moving]
• If no tach feedback is available perform
speed sensor test (page 21).
• Check continuity of tach feedback
portion of the data cable (To identify
tach feed back lines see wiring diagram
section for specific model).
--------
• Check/Adjust tread belt tension (page
22)
• Perform speed sensor test (page 21) If
speed sensor fails adjust gap, if still
fails-replace speed sensor.
• Perform belt / deck wear test (page 24)
If badly worn, replace belt and deck.
• Replace PWM
--------
• Restart unit- if error persists, replace
control panel.
Multi-meter
Socket Set
Silicone Lubrication
Packet
Silicone Lubrication
Applicator
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 11
Symptom Probable Cause Corrective Action Recommended Tools
NO DISPLAY No power at the 110
VAC outlet.
No power to the
treadmill.
No power to the
control panel.
•
Check home circuit breaker. Reset as
necessary.
• Test for 110 VAC at outlet.
• Identify if outlet is a GFI.
Note: Some brands of GFI
outlets are too sensitive for
treadmill use. Call the help
line if encountering GFI
issues.
--------
• Check for AC light on PWM.
(See diagram pages 23-30)
• Check for 110 VAC at power cord.
Replace if no power.
• If Yes- Check for 110 VAC at tread
power switch. Replace if no power.
• If Yes-Check for 110 VAC at tread
circuit breaker. Replace/ reset if
necessary.
• If Yes- Check for 110 VAC at PWM
across AC1 & AC2.
• If Yes- Replace PWM.
--------
• Check status LED +11 VDC on PWM
(See diagram pages 23-30). If not
remove fuses and check continuity as
replace as needed.
• If Yes- Check wire harness connections
at PWM and Control Panel. Reconnect
as needed.
• If Yes- Check voltage on harness at
panel. Refer to wiring diagram for your
machine type in wiring diagram section.
If voltage is present– replace panel and
recalibrate (page 16). If voltage is not
present check voltage at PWM. If
voltage is present at PWM replace
pedestal wire harness. If 0 VDC
replace PWM and recalibrate (page 16).
Allen Key set.
Phillips head
screwdriver.
Multi-meter.
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
Page 12
Symptom Probable Cause Corrective Action Recommended Tools
CIRCUIT
BREAKER
TRIPS
Possible short in
treadmill wiring.
Motor issues.
Incline motor
drawing treadmill
down
Bad PWM
Too much tension
on belt or
obstruction under
belt.
Weakened circuit
breaker or High
belt/deck friction
• Power off the treadmill and inspect all
wiring for shorts or burned areas.
• Secure all connectors.
--------
• Disconnect motor leads from the PWM.
Power on treadmill, press start. If the
breaker does not trip check the motor
brushes and perform the motor test
procedure (page 22).
• Reconnect motor to the PWM, if the
breaker trips- replace the motor.
--------
• Unplug incline motor.
• Power on treadmill, if breaker does not
trip- replace incline motor.
--------
• Unplug PWM, power on machine. If
breaker doesn’t trip- replace PWM.
--------
• Check for correct tension adjustment
(page 22)
• Check for obstruction- remove
obstruction.
--------
• Perform AC Amp Draw Test (page 20)
at circuit breaker.
• If draw is less than 15 amps
continuously - replace breaker.
• Perform Amp Draw test (page 20) If
Amp draw is higher than recommended
try push test (page 24) procedure.
Allen Key set
Needle nose pliers
Socket set
Multi-meter
Note:
All trouble
shooting should
be performed in
calibration
mode.
Page 16
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 13
Symptom Probable Cause Corrective Action
Soft Select
Malfunctions
Control Panel Issues
Mechanical Issues
Incorrect/ Missing
Count Values
Defective Motor/
Start Capacitor
• Enter calibration mode
• Is there a count value displayed in the distance window? If No
replace control panel. If yes- continue to next step.
--------
• Press and hold the softer button, release. Press and hold the firmer
button to detect carriage movement in both directions. If the carriage
cannot go full range from –220 and consistently stops in the same
place, check for mechanical binding. Inspect the under pan for
damage or areas that cause mechanical binding. Also inspect the
carriage track in the side frame for binding. If the carriage cannot
move to its full range and back in the time limit, check for
mechanical binding.
• If the carriage is not moving and the motor is turning, check the set
screws holding the drive shaft to the motor shaft.
--------
• Threaded shaft turns when commanded but the pulse count does not
display/ or does not change. Physically check the hex cam located at
the front of the shaft and on the motor shaft. Hex cam should be
firmly attached. If hex cam slides freely super gluing it back onto the
shaft can repair it.
• Hex cam moves but counter does not register. Ensure that the micro
switch is properly adjusted and the switch is being made when the
hex cam points press against the roller.
• Disconnect the cable at J4 and check for continuity on cable. Cable
should have continuity if the switch roller is in a flat area of hex cam.
If no continuity- replace cable. If good continuity, place cable back
on J4 and continue
• While in calibration mode place the multi-meter leads on J4 and
check for 5 Volts. If no 5 Volts- replace board.
--------
• If command and count data/voltage are present and Led 1 indicates
AC voltage is good but soft select motor does not respond. Set
probes on TP 8 and TP3, press soft command (with soft select limit
switch not activated) result should be 120 VAC. Set probes on TP8
and TP2 and press firm command (with soft select limit switch not
activated) result should be 120 VAC. If no 120 VAC on either test
point- replace soft select board. If voltage is correct- continue to next
step.
• In calibration mode, place red lead on the larger red wire and post on
the start capacitor of the soft select system and the black lead on the
common black lead, press firm- the result should be 120 VDC. Next
place the white lead on the larger white wire and post on the start
capacitor of the soft select system and the black lead on the common
black lead; press soft- the result should be 120 VDC. If voltage is
correct- replace the motor. If voltage is incorrect- replace the start
capacitor.
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
Page 14
Symptom Probable Cause Corrective Action
Soft Select
Malfunctions
(continued)
AC Power Issues
Wire Harness
• Is AC power LED D3 lit?
• No- check F1 fuse. If F1 is good check for AC voltage between TP1
and TP5. If fuse and voltage are good- replace the board.
--------
• Yes- While in calibration mode Press the Softer button- LED D1
should light, press the Firmer button- LED D2 should light. If the
lights respond to the button then command is being sent from the
upper board and received at the soft select board. If lights do not
respond check or replace 6-pin data cable, if cable is ok- replace
upper panel.
-------
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 15
SOFT SELECT BOARD
ILLUSTRATION
Calibration Procedures
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
SS 100 PWM (5-xxxxx to 6-79999 serial numbers)
Entering Engineering Mode:
With safety key in, power up unit while holding Grade Up and Grade Down keys.
Incline will reset to zero.
Mode 1: Max Speed
Press Select/Enter- 01 (C1 for 450) appears in Distance.
Adjust speed using Fast and Slow buttons until 10 or 12 mph
Verify speed by counting belt revolutions: 10mph= 102 Belt revs/per min. 12mph= 121 Belt revs/per min.
Press Start/Reset to save max speed, wait for belt to stop.
Mode 2: Speed Table
Press Select/Enter-02 (C2 for 450) appears in Distance
Press Start/Reset to set speed table. Treadmill will speed up and slow down on its own. Wait for belt to
stop.
Mode 3: Incline
Press Select/Enter- 03 (C3 for 450) appears in distance
Press Grade Up to upper incline limit, then back down slightly
Save upper limit by pressing Start/Reset
Turn treadmill off and then back on and check operation
SS90 Calibration (6-8xxxx serial numbers and after)
Enter Calibration Mode by holding the Up and Down keys while inserting the safety key
In message center window displayed: Press Start to Calibrate
NOTE: In Calibration mode, it is possible to check if the speed sensor is reading all the front roller
magnets: the Met light will light when a magnet is in front of the sensor. Speed must be less than 1 mph.
Press Start/Reset to begin calibration
Treadmill will elevate and speed up/slow down. Wait for belt to stop.
Message center window will display: Successful, or will indicate error area.
Remove and re-insert safety key. Check operation of treadmill.
Page 16
DIAGNOSTICS
(
Available onl
y
in SS90 Machines
)
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
To enter diagnostic mode, press and hold the FAST and SLOW buttons while pushing in the safety key.
The control panel will show “Diagnostics”.
Press the UP button: Total Hours (in whole hours)
Press the UP button: Distance (in miles, two digits past decimal point)
Press the UP button: Average Speed (in mph)
Error List (This is an error log, but just a list of errors possible on the unit.)
S1: Lube
S2: Clean
S3: Motor
S4: Sensor
E1: Minimum
E2: Overspeed
E2: Cal
E3: EPROM
Remove Safety Key to exit Diagnostics
Page 17
Page 18
TEST PROCEDURES
Grounded Outlet Test Page 20
Amp Draw Test Page 20
Speed Sensor Test Page 21
Voltage to Drive Motor Test Page 21
Drive Motor Test Page 22
Drive Belt Tension Test Page 22
Tread belt Tension Test Page 22
Incline Potentiometer Calibration Test Page 23
Voltage to Incline Motor Test Page 23
Belt / Deck Wear Test (Push Off Test) Page 24
Page 19
TEST PROCEDURES
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
GROUNDED OUTLET TEST
This test is very important for optimal HRC and incline operation.
Set voltmeter for Volts AC
Place 1 lead in the right side of the outlet (hot)
Place 1 lead in the ground plug
A properly grounded outlet will read 110 VAC
AMP DRAW TEST
This test is a good indicator of the wear condition of the belt and deck, and the need for lubrication.
The treadmill circuit breaker will trip at 15 amps, so be sure the voltmeter you are using is rated for at least
15 amps when you are load testing the treadmill. This test can be performed either on one of the AC power
cord leads or on one of the DC motor leads from the PWM to the motor. Testing the amp draw at certain
speeds without load and with load will signal whether higher than normal amp draw is a result of PWM
failure or increased friction from belt and deck wear.
AC AMP DRAW PROCEDURE
This procedure requires an AC clamp-on ammeter. Place the clamp around either of the power cord
leads, black or white. Load test requires a person to walk on the tread belt for 5-10 minutes.
2.5 mph w/out load 2.0-2.5 AMPS AC
2.5 mph with load 2.75-3.75 AMPS AC
5.0 mph w/out load 3.5-4.0 AMPS AC
5.0 mph with load 5.0-7.0 AMPS AC
DC AMP DRAW PROCEDURE
This procedure can be performed with an ordinary voltmeter. (Note: Be sure the voltmeter is rated
to handle 15 DC amps.) Disconnect the red motor lead from MTR1 on the PWM. Connect the
voltmeter to MTR 1 on the PWM and the other voltmeter lead to the red motor lead so that the
voltmeter completes the connection of the PWM to the motor.
2.5 mph w/out load 4.5-5.0 AMPS DC
2.5 mph with load 7.0-8.0 AMPS DC
5.0 mph w/out load 5.0-5.5 AMPS DC
5.0 mph with load 8.5-9.0 AMPS DC
Higher than normal amp draws without load may signal that belt tension is too tight or there is a
problem in the Drive Motor or PWM. Perform the Drive Motor Test and visually check the motor
brushes before replacing the PWM. Higher than normal amp draws with load after normal readings
without load signal belt and deck friction which may require lubrication or replacement.
Page 20
TEST PROCEDURES
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
SPEED SENSOR TEST
This test is used to verify sensor operation in conditions of speed fluctuation, E2: Cal error, S4:
Sensor error, E2: Overspeed error or Unsuccessful Calibration.
SS100 (Serial numbers 5-xxxx to 6-7999)
Set voltmeter to Volts DC. Treadmill power on speed and speed at 0mph
Attach voltmeter leads across outside 2 contacts at P2 on PWM
With magnet in front of sensor, 0 VDC
With no magnet in front of sensor, 3.0 VDC
SS90 (Serial numbers 6-8000 and above)
Set voltmeter to volts DC. Treadmill power on and speed at 0 mph
Attach voltmeter leads across outside 2 contacts at J1 on PWM
With magnet in front of sensor, 0 VDC
With no magnet in front of sensor, 5 VDC
Check the sensor on every magnet, adjust sensor until voltage shows
In calibration mode before pressing Start, the tread belt can be moved manually and the Met light
will blink when a magnet is in front of the sensor.
VOLTAGE TO DRIVE MOTOR TEST
This test is used to diagnose conditions of NO Belt Movement, or Speed Fluctuations
Set voltmeter to volts DC and adjust speed on Control Panel to 4 mph
Attach red voltmeter lead to MTR1 on PWM with motor wires attached
Attach black voltmeter lead to MTR2 on PWM with motor wires attached
0 VDC signals no PWM output
166 VDC signals open circuit in motor or motor connection
Operating voltage will lay between 0 VDC and 166 VDC
NOTE: The reason that we do not narrow down PWM output voltage is that the PWM output is a pulse
signal. The sampling rate of the voltmeter used will determine what output voltage the voltmeter is able to
read.
Page 21
TEST PROCEDURES
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
DRIVE MOTOR TEST
This test is used in conditions of No Belt Movement.
Unplug treadmill and set voltmeter to volts DC
Disconnect motor leads from PWM
Place 1 voltmeter lead in each motor wire
Gently spin the motor flywheel and check for voltage DC
2-5 VDC means normal motor operation
0 VDC means motor malfunction
DRIVE BELT TENSION TEST
This test is used in front roller replacement and in conditions of belt slipping.
Place two fingers on top of the drive belt halfway between the front roller pulley and the drive motor
pulley.
With moderate pressure push down on belt
If belt deflects down more than 1/8 “, tighten motor mounts
If belt deflects down less than 1/8 “, loosen motor mounts.
It is also possible to twist the belt; you should be able to twist the belt almost to a vertical position
TREADBELT TENSION TEST
This test will address belt slipping and is used in any roller replacement or deck replacement. Ensure that
the drive belt is properly tensioned before adjusting tread belt tension. Belt and deck wear and/or lack of
lubrication can cause the tread belt to show symptoms similar to loose tread belt tension- check these
conditions before adjusting tread belt tension.
Turn treadmill on and adjust speed to 2 mph
Walk heavily on the belt pulling slightly against belt movement
If hesitation or slip is detected, tighten tread belt tension bolts ¼ turn
Repeat until no hesitation or slip is encountered. Check at higher speeds
Tread belt tension is too tight if the belt feels stiff to touch with no give or the belt groans against the rollers.
You should be able to insert your hand between the belt and deck palm up almost to your thumb when the
belt is at proper tension.
Page 22
TEST PROCEDURES
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
INCLINE POTENTIOMETER CALIBRATION TEST
This test can correct E1: Minimum conditions and aid in diagnosis of incline problems with finding zero or
target incline.
SS100 and SS90
Set voltmeter to Ohms (Ω) with treadmill unplugged from wall
Place 1 voltmeter lead on pin 3 (Blue) and 1 lead on pin 2 (Orange)
Check for 800 Ohms
SS90 Only: In calibration mode before pressing Start, the Distance window displays the incline number.
With the treadmill at zero, the number should be between 160 and 180. 0 often indicates a wire
harness misconnection or failure of signal to panel.
As the unit inclines during calibration, watch the numbers in the Distance window, if they do not
increase by at least 60 from the zero value, an E1: Minimum error will result. Then the zero value
may need to be rest to a lower value.
If incline potentiometer needs adjustment, remove swivel opines and twist incline motor shaft by hand for
SS100 or use Up and Down keys for SS90. (See diagram on T-6)
VOLTAGE TO INCLINE MOTOR TEST
This test is utilized in conditions of No Incline Movement, Incline Fluctuation, or E1: Minimum.
Set voltmeter to AC volts. To access incline plug, PWM screws may need to be removed.
Place voltmeter leads across White and Black while pushing UP button
10 VAC indicates normal PWM output, 0 VAC signals no output
Place voltmeter leads across Red and White while pushing Down button
110 VAC indicates normal PWM output, 0 VAC signals no output
Page 23
TEST PROCEDURES
Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148
Belt / Deck Wear Test
This is a simple physical test to gauge the general level of friction present between the deck and belt.
1. While the treadmill is not running, inspect the condition of the underside of the tread belt. The fabric
should be soft and porous. If the belt appears glazed- replace the belt.
2. While the treadmill is not running, slide your hand under the belt and feel the surface of the deck.
The deck should feel smooth with no abrasions or scratches.
If any abrasions or scratches are found- replace the deck.
Push Off Test
Place the machine in Calibration mode, elevate to the highest elevation- speed should be set to 0. Stand on
the tread belt positioning yourself close to the console; push off with moderate force. The elevation
combined with your weight and the force of the push should cause the belt to carry you all the way to the
end of the machine*. If the test does not carry you to the end of the machine lubricate the belt using True
Fitness liquid silicone. After lubricating the belt/deck perform the push off test again. If it does not pass the
test after lubricating replace the belt and deck
* Note: Residential treadmills may only carry about ¾ of the distance of the deck due to higher tension on
the belt.
Page 24
WIRING DIAGRAMS
350 Gray Page 26
350 Black Page 27
400 Page 28
450/500/700 Page 29
500CI/750CI Page 30
750 NON/P Page 31
750 Page 32
Page 25
Page 26
350 Gray
Wiring Diagram
Page 27
350 Black
Wiring Diagram
Page 28
400
Wiring Diagram
Page 29
450/500/700
Wiring Diagram
Page 30
500CI/750CI
Wiring Diagram
Page 31
500CI/750CI
Wiring Diagram
Page 32
750
Wiring Diagram
Model 350-450
Parts List
350, P, HRC Page 34
350PB, HRCB Page 37
400, P, HRC Page 39
450, P, HRC (SS100-SS90) Page 41
Page 33
350 P, HRC
PART # DESCRIPTION
CONTROL PANEL
350 Board Only 70186311 350 P Board Only
(98- Present) 70186310 350 HRC Board Only
(98-PRESENT) 70186401 350P CONTROL PANEL 98-now
70186402 350HRC CONTROL PANEL 98-NOW
(HARDWARE) 70185400 HRC RECEIVER ASSY.
70151900 5/8" DOME PLUG FOR HR RECEIVER
70176000 C.P. TAPE 3/8 DOUBLE COATED FOAM
70150000 SAFETY SWITCH ASSY.
70177400 SAFETY KEY ASSY.
OVERLAYS
70186411 350P GRAY OVERLAY
70186412 350HRC GRAY OVERLAY
PWM
LOWER BOARD (PWM)
70013500 PWM SCREW 10-32 X 3/8 PPHTF
70350300
SPEED SENSOR
70202600 SPEED SENSOR
70350300 EXTENDER WIRE FROM SENSOR -PWM
70190800 SPEED SENSOR SCREW
DATA CABLE
70138600 6- CONDUCTOR INTERFACE CABLE
70138700 8- CONDUCTOR INTERFACE CABLE
70190100 8- CONDUCTOR INTERFACE CABLE- HRC
DRV MTR
70187600 DRIVE MOTOR ASSY.
70166600 MOTOR DRIVE PULLEY
70173400 MOTOR COVER
DRV BELT
70127500 POLY-V-BELT
ELEVATION MTR
70186800 INCLINE MOTOR
70183600 CLEVIS PIN 3/8 X 1 3/4
70116700 COTTER PIN 1/16 X 1 5/16
70183700 CLEVIS PIN 3/8 X 2 1/8
70164800 COTTER PIN 3/32 X 1/2
70183200 INCLINE CAPACITOR
Page 34
350P, HRC
PARTS LIST
ELEVATION RACK
70184401 ELEVATION RISER ASSY.
70176700 MOLDED WHEEL
70182300 INCLINE RISER BOLT 5/16- 18 X 1 1/4
70115200 INCLINE RISER WASHER 3.8 I.D. X 7/8 O.D.
70209900 INCLINE RISER NUT 5/16- 18 AUTOMATION GR.
POWER CORD
70253100 9FT. POWER CORD
70008200 STRAIN RELEIF BUSHING
ON / OFF SWITCH
70251100 ROCKER ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70208500 TREADBELT 18" X 107"
DECK
70186700 FLEX DECK ASSY.
70020200 DECKSCREWS/BUMPER FEET 10- 32 X 1 1/4 PPH
FRONT ROLLER
70217500 FRONT ROLLER ASSY.
70188500 FR ROLLER BOLT 1/4- 20 X 2 Gr. 5 Hex Hd.
70185300 FR ROLLER NUT 1/4- 20 NYLOC NUT
REAR ROLLER
70188000 REAR ROLLER ASSY.
70175100 REAR ROLLER COVER-LEFT
70175200 REAR ROLLER COVER-RIGHT
70104000 R ROLLER SCREW 10 X 1/2 PPH Tek Screw
STRADDLE COVERS
70173301 STRADDLE COVER- L.H. 350P
70173302 STRADDLE COVER- R.H. 350P
70173303 STRADDLE COVER- L.H. 350 HRC
70173304 STRADDLE COVER- R.H. 350 HRC
70086700 STRADDLE COVER SCREW 6 X 1
70182400 INSIDE COVER SPACER
70030900 3/8 X 1/16 X Lg. DOUBLE STICK TAPE
70165400 OUTSIDE COVER SPACER
RAMRAILS
70188700 HANDRAIL ASSY. L.H. BLACK
70188800 HANDRAIL ASSY. R.H. BLACK
Page 35
70212300 HANDRAIL ASSY. L.H. GRAY
70212400 HANRAIL ASSY. R.H. GRAY
70185100 LOWER HANDRAIL BUSHING 1/4- 20 X 3 3/4
70198900 LOWER HANDRAIL BUSHING 3/8 OD X 1"
70183101 H/BAR NUT PLATE
PEDESTAL
70157000 PED. STAR WASHER 1/4 I.D.INTERNAL TOOTH WASHER
70186600 PEDESTAL WELDMENT
70179901 STRAP CLAMP PED.
70155900 PED. SCREW 1/4- 20 X 5/8 BHSCS
FRAME
70181901 FRAME WELDMENT
70160100 BUMPER ASSY
70155200 BUMPER- 1 1/2 X 2 X 1 1/8
Page 36
350PB, HRCB
PART # DESCRIPTION
CONTROL PANEL
(350B) Board Only 70237311 350PB Board Only
70237310 350HRCB Board Only
70242000 350PB CONTROL PANEL
70242001 350HRCB CONTROL PANEL
70150000 SAFETY SWITCH ASSY.
70185400 HEART RATE RECIEVER
70245100 PLASTIC HRC COVER
70177400 SAFETY KEY
OVERLAY
70242010 350PB DOT/OVERLAY
70242011 350HRCB DOT/OVERLAY
PWM
(99-PRESENT) 70244200 PWM MOTOR CONTROLLER
70013500 PWM SCREW 10-32X3/8
SPEED SENSOR
70243203 CIRCUIT BOARD SPEED SENSOR
70243300 SPEED SENSOR SCREW 4-40X1/4
DATA CABLE
70264100 6COND./CORD DATA CABLE 350PB, HRCB
70264000 8COND/CORD DATA CABLE 350PB
70190100 8-CONDUCTOR INTERFACE CABLE(HRC)
DRV MTR
70245600 DRIVE MOTOR Core charge included
DRV BELT
70127500 1687J10 POLY-V-BELT
ELEVATION MTR
70186800 ELEVATION MOTOR-HUBBLE
(HARDWARE) 70183200 ELEVATION MOTOR CAPACITOR
70183600 INCLINE MOTOR CLEVIS PINS 3/8X1 3/4
70116700 INCLINE MOTOR COTTER PIN 1/16X1-5/16
70183700 INCLINE MOTOR CLEVIS PIN 3/8X2-1/8
70164800 INCLINE MOTOR COTTER PIN 3/32X1/2
ELEVATION RACK
70184402 ELEVATION RACK
Page 37
350PB, HRCB
PARTS LIST
(NEW STYLE) 70176700 MOLDED WHEEL
70182300 INCLINE RISER BOLT 5/16X1 1/4
70115200 INCLINE RISER WASHER 3/8 I.D.
70209900 INCLINE RISER NUT 5/16-18
POWER CORD
70253100 9 FOOT POWER CORD
70008200 STRAIN RELIEF BUSHING
ON / OFF SWITCH
70251100 ON/OFF ROCKER SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70208500 TREADBELT 18" X 107"
DECK
70186700 FLEX DECK
70020200 DECK SCREWS
70232700 DECK BUMPERS
FRONT ROLLER
(ADJUSTABLE) 70260100 FRONT ROLLER W/8 MAGNETS
70188500 FRONT ROLLER BOLT 1/4-20X2 GR. 5
70185300 FRONT ROLLER NYLOK NUT 1/4-20
REAR ROLLER
70188000 REAR ROLLER
70220800 REAR ROLLER COVER LH BLACK
70220900 REAR ROLLER COVER RH BLACK
70104000 10X1/2 REAR ROLLER SCREW
STRADDLE COVERS
70173305 LH STRADDLE COVER BLACK
70173306 RH STRADDLE COVER BLACK
70086700 STRADDLE COVER SCREW 6X1
70030900 DOUBLE SIDED STICK TAPE
PEDESTAL
70157000 PEDESTAL STAR WASHER
70173401 MOTOR COVER
70155200 BUMPER FEET
70020200 BUMPER FEET SCREWS
70183101 H/BAR NUT PLATE
Page 38
Control Panels
7T007500 400P Control Panel assy w/ Electronics
7T007501 400HRC Control Panel assy W/ Electronics
7T007502 400P Electronics Only
7T007503 400HRC Electronics Only
7T008000 Upper Plastic Front and Rear (400HRC)
7T008001 Upper Plastic Front and Rear (400P)
Overlays
7T010201 Panel Overlay 400P
7T010200 Panel Overlay 400HRC
7T014200 Panel Overlay T-400HRC
PWM
7T007400 PWM W/O Hardware
7T008500 Speed sensor
7T013900 PWM W/O Hardware (230V)
Filter
7T014800 Filter, EMI 400 250V/10A CP6-1022C
7T014000 Bracket, Filter 400 (T=2.0)
7T014100 Bracket Screw Phillips Head M5X0.8X6L UCP
Choke
7T014400 Choke, 400 3MH 220V
Inductor
7T014900 Inductor (choke) 400 6MH 8A
Data Cable
7T007600 Wire Harness
Drive Motor
7T007800 2.75 HP Drive Motor
7T014300 2.75 HP Drive Motor 230V
Drive Belt
7T008400 Drive Belt
Elevation Motor
7T009600 Elevation Motor
7T009700 Front Wheel
7T014500 Elevation Motor 230V 1/6HP
Power Cord
7T009800 Power Cord
Page 39
400P, HRC
PARTS LIST
7T014600 Power Cord 400 AC220V 1.5MM 2800MM
On/Off Switch
7T009900 On/Off Switch
Circuit Breaker
7T010000 Circuit Breaker
7T014700 Circuit Breaker 400 10A 220V 400RFMB Series
Tread belt
7T008300 Tread belt
Deck
7T008600 Deck, pre drilled
Front Roller
7T008100 Front Roller
Rear Roller
7T008200 Rear Roller
7T009200 Roller Cover - L
7T009300 Roller Cover - R
Straddle Covers
7T009500 Straddle Cover Set
Hardware Kit
7T007900 Complete Hardware Kit
Heart Rate Strap
7TMC0608006 HRC Strap
Safety Key
7T010300 Safety Key
Page 40
PART # DESCRIPTION
CONTROL PANEL
(SS100) 70120000 450NON SS100CONTROL PANEL
70120100 450P SS100 CONTROL PANEL
70175900 450HRC SS100 CONTROL PANEL
(450's) Board Only 70132418 450NON SS90 CONTROL Board Only 97-98
70132417 450P SS90 CONTROL Board Only 97-98
70132416 450HRC SS90 CONTROL Board Only 97-98
(97-98 STYLE) 70161011 450NON SS90 OVERLAY 97-98
(OVERLAYS) 70161013 450P SS90 OVERLAY 97-98
70161012 450HRC SS90 OVERLAY 97-98
(99-PRESENT) 70242110 450NON DOT OVERLAY 99-PRESENT
70242111 450P DOT OVERLAY 99-PRESENT
70242112 450HRC DOT OVERLAY 99-PRESENT
PWM
(SS100) 70113900 MOTOR CONTROLLER (SS100)
(SS90) 70132500 MOTOR CONTROLLER SS90
70013500 PWM SCREW 10-32 X 3/8
SPEED SENSOR
(SS100 STYLE) 70104200 SPEED SENSOR (SS100)
70154800 SPEED SENSOR W/ WIRE AND BRACKE
(SS90 STYLE) 70243200 CIRCUIT BOARD SPEED SENSOR
70243300 SP. SENSOR SCREW 4-40 X 1/4
DATA CABLE
70337900 450NON AND PROG. DATA CABLE
70337800 450 HRC DATA CABLE
DRV MTR
70325500 3HP DRIVE MOTOR 10 MPH
DRV BELT
70006300 210J10 POLY-V DRIVE BELT
ELEVATION MTR
70113200
INCLINE MOTOR
(ELEVATION- 70115500 3/8 X 1 1/2 CLEVIS PIN
HARDWARE) 70116700 1/16 DIA. X 1 5/16 COTTER PIN
450P, HRC
(SS100-SS90)
PARTS LIST
Page 41
70118900 TORQUE ARM SWIVEL PIN
70183200 START CAPACITOR FOR INCLINE MOTOR
70013500 SCREW FOR START CAPACITOR
LLS
70121000 LOWER LIMIT SWITCH
70125700 LLS SCREW 10X 1/4
70120500 LLS TO PWM WIRE
ELEVATION RACK
70281001 ELEVATION RISER SUB ASSY.
WHEEL 70176700 BEFORE AUG 99
POWER CORD
70253100 9 FT. POWER CORD
70008200 STRAIN RELIEF BUSHING
ON / OFF SWITCH
70251100 ROCKER ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER SWITCH
TREADBELT
70159300 17 3/4" X 107 3/4" 2 PLY TREADBELT
DECK
70157700 FLEX DECK
70020200 DECK SCREW 10/32 X 1 1/4
FRONT ROLLER
(SS100-NARROW) 70123800 FRONT ROLLER (SS100)
(96-xxxx - 99) 70217000 450 FRONT ROLLER(6-8XXXX-99)
(99-81023G TO) 70359200 450 ADJ. ROLLER
(PRESENT)
REAR ROLLER
70359000 REAR ROLLER
70158900 ROLLER BOLT
70159000 5/16 INTERNAL TOOTH LOCK WASHER
STRADDLE COVERS
70162000 LT & RT STRADDLE COVERS
70030900 3/8 X 1/16 X 108 FT. DBL. STICK TAPE
70243400 BLUE TAPE 1/2 X 150 FT. ROLL
PEDESTAL
(98 style) 70176800 Pedestal Weldment, 450 W/ end caps
(99- 00 style) 70233200 ROUND PEDESTAL WELDMENT
70155900 PEDESTAL SCREWS
FRAME
70255903 FRAME WELDMENT ADJ. FRONT ROLLER
70155200 BUMPER FEET
70020200 BUMPER FEET SCREW 10/32X1 1/4PPH
Page 42
Model 500-550
Parts List
500, P, HRC (SS100-SS90) Page 44
500Z & ZT, P, HRC Page 48
540, P, HRC, CI (NON Z) Page 51
540Z, ZT, P, HRC, CI Page 54
550, P, HRC Page 57
550z, P, HRC, CI Page 59
550 ZTX, P, HRC, CI Page 61
Page 43
PART # DESCRIPTION
CONTROL PANEL
500 Boards Only (SS90) 70132415 500NON Board Only
Up to 98 with a letter 70132414 500P Board Only
70132413 500HRC Board Only
70176911 500CI Board Only
500 (99 Style Board Only) 70237523 500P Board Only
(98 with a letter) 70237522 500HRC Board Only
70237612 500CI Board Only
500A (2000) Style Board Only 70237415 500A NON Board Only
70237414 500A P Board Only
70237413 500A HRC Board Only
70018100 CHERRY SWITCH (SS100)
70150000 SAFETY SWITCH-ASSY
70177400 SAFETY KEY
70020400 SAFETY SWITCH SCREWS
70020600 SAFETY SWITCH NUTS
70185400 HEART RATE RECEIVER
70138500 POLAR HEART RATE CHEST STRAP
70284100 Old 500
70240503 EXTRUSION-PANEL CLIP 26 3/4"
OVERLAY
(SS100 OVERLAY) 70119301 500 NON OVERLAYS-SS100
70119901 500P OVERLAYS-SS100
70179701 500 HRC OVERLAYS-SS100
(98 OVERLAY) 70160811 500 NON SS90 OVERLAY 98 STYLE
70160813 500 P SS90 OVERLAY 98 STYLE
70160812 500 HRC SS90 OVERLAY 98 STYLE
(99 OVERLAY) 70242211 DOT/OVERLAY ASSY, 500P
(98 with a letter) 70242212 DOT/OVERLAY ASSY, 500HRC
(2000 STYLE) 70265100 DOT / OVERLAY ASSY, 500A
70265011 DOT / OVERLAY ASSY, 500A HRC
70265012 DOT / OVERLAY ASSY, 500A P
70242410 DOT / OVERLAY ASSY, 500CI
PWM
(SS100) 70113900 PWM MOTOR CONTROLLER-SS100
70132500 SS90 PWM MOTOR CONTROLLER
Page 44
500P, HRC
(SS100-SS90)
PARTS LIST
70183500 500CI PWM [96-80000]-[98-80000]SS95
SPEED SENSOR
70154800 SPEED SENSOR ASSY.-SS100
70243200 SS90 SPEED SENSOR NEW STYLE
DATA CABLE
(SS100) 70119400 DATA CABLE-SS100 NON, P, HRC
70120400 LOWER WIRE HARNESS-SS100
70337900 INTF. CABLE ASSY 500 N/P SS90
70337800 INTF. CABLE ASSY 500 HRC SS90
DRV MTR
(SS100) 70155101 DRIVE MOTOR-2.0 10MPH
70155102 DRIVE MOTOR-2.5 12MPH
70325500 DRIVE MOTOR 3HP SS90-Z SERIES
70125600 DRIVE MOTOR-CARRIAGE BOLT
DRV BELT
70006300 DRIVE BELT 210J10-V BELT
ELEVATION MTR
70113200 ELEVATION MOTOR
70118900 SWIVEL PIN
70183200 INCLINE START CAPACITOR
70115500 CLEVIS PIN 3/8 DIA. 1 1/2" LONG
70116700 COTTER HAIR PIN .062 DIA.
70022600 SET SCREW, INCLINE, SWIVEL PIN
LLS
70121000 LOWER LIMIT SWITCH
70120500 WIRE-PWM TO LOWER LIMIT SWITCH
ELEVATION RACK
70281002 ELEVATION RACK
70154600 INCLINE BEARING BLOCK
70126200 FLANGED INCLINE BEARING
WHEEL / BOLTS
70176700 MOLDED WHEEL, 2 1/4" DIA. 3/8 HOLE
70003100 SHOULDER BOLT-FRONT WHEEL 3/8 X 1"
(NEW STYLE) 70176701 MOLDED WHEEL, 2 1/4" DIA 1/2" HOLE
70174300 1/2" X 1" SHOULDER BOLT
POWER CORD
70253100 POWER CORD, 120 VAC
70013900 BUSHING-3/8"BLACK
70008200 STRAIN RELIEF BUSHING
Page 45
ON / OFF SWITCH
70251100 ON/OFF SWITCH
70261000 220V ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70159400 TREADBELT
70058100 STRETCH-TREADBELT
70058200 ORTHO-TREADBELT-20X108 ROL-TOP
70068500 ORTHO-STRETCH TREADBELT
DECK
(SS100) 70072800 DECK ASSY
70072700 STRETCH DECK ASSY
70157900 FLEX DECK ASSY. 500/WELDED
70157800 STRETCH DECK ASSY, 500S/WELDED
(DECK HARDWARE) 70232700 DECK BUMPER-ASSY.
70086700 DECK BUMPER SCREWS
70020200 DECK SCREW 10-32 X 1 1/4"
FRONT ROLLER
(SS100) 70119500 FRONT ROLLER-95 WIDE WITH 4 MAG.
70207800 ROLLER SCREW
70217300 FRONT ROLLER ASSY, '99 97
70255400 FRONT ROLLER ASSY, ADJ. '00
HARDWARE - ADJ. 70188500 BOLT 1/4-20 / ADJ. END
70185300 NUT 1/4-20
70256800 FLAT WASHER
70190900 FLANG BOLT 1/4-20 FIXED END
REAR ROLLER
(SS100) 70073600 REAR ROLLER ASSY SS100
70157400 REAR ROLLER ASSY, WELDED SS90
STRADDLE COVERS
(SS100) 70074700 STRADDLE COVER-RIGHT SIDE
70074900 STRADDLE COVER-LEFT SIDE
70162101 STRADDLE COVER ALM. '99 STYLE
70162102 STRETCH STRDL. CVR. ALM. '99 STYLE
70263900 STRADDLE COVER PLASTIC 500A,P,HRC
Page 46
PEDESTAL
(SS100) 70122200 PEDESTAL ASSEMBLY-VINYL
70070200 HANDLEBAR
70155900 PEDESTAL SCREW
70013500 HANDLEBAR SCREWS #10-32X3/8
('98 STYLE) 70179600 PED.-WELDMENT 500NON,P,HRC '98
70179500 PED.-WELDMENT 500CI '98
('99-'00 / '98 W/LETTER) 70233300 PED.-WELDMENT 500 NON,P,HRC '99-'00
70233400 PED.-WELDMENT 500CI '99-'00
70204200 RAM RAILS NON CHR
FRAME
70155200 BUMPER FEET
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
70204200 RAM RAILS NON CHR
FRAME
70155200 BUMPER FEET
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 47
CONTROL PANEL PART # DESCRIPTION
(500ZT's) Overlay Only 70327510 500ZT NON/P Overlay Only
Z also 70327511 500ZT HRC Overlay Only
(500ZT'S) BOARDS 70328016 500ZT NON CONTROL BOARD ONLY
ONLY 70328015 500ZT P CONTROL BOARD ONLY
70328014 500ZT HRC CONTROL BOARD ONLY
(500ZT EX'S) BOARDS 70328056 500ZTEX NON CONTROL BOARD ONLY
ONLY International 70328055 500ZTP EX CONTROL BOARD ONLY
70328054 500ZTHRC EX CONTROL BOARD ONLY
SAME PANELS 70328100 500Z,ZT NON PANEL
AS NEW 500ZT 70328101 500Z,ZT P PANEL
SERIES. 70328200 500Z,ZT HRC PANEL
70290601 PANEL, BOTTOM CONSOLE
70294301 PANEL LF.LWR. GRIP CLOSURE
70290801 PANEL RT.LWR. GRIP CLOSURE
70290701 HANDLE LT. CONSOLE
70290801 HANDLE RT. CONSOLE
70331000 MAGNET SAFETY KEY
PWM
70132500 PWM - MOTOR CONTROLLER
500 ZT SERIES 70342900 7/21/2003 PWM - MOTOR CONTROLLER
SPEED SENSOR
70243200 CIRCUIT BOARD SPEED SENSOR
70243300 SPEED SENSOR SCREW
DATA CABLE
70337900 500Z NON DATA CABLE ,P
70337800 500Z HRC DATA CABLE
500 ZT SERIES 70341300 20 PIN DATA CABLE
DRIVE MOTOR
70325500 3HP DRIVE MOTOR
70341500 500ZT DRIVE MOTOR
DRV BELT
70006300 DRIVE BELT 210J10
Page 48
500Z & ZT, P, HRC
PARTS LIST
ELEVATION MTR
70113200 ELEVATION MOTOR
70183200 ELEVATION START CAPACITOR
70115500 3/8X1 CLEVIS PIN
70116700 COTTER PIN
70013500 10-32 X 3/8 PPH SCREW
70118900 TORQUE ARM SWIVEL PIN
LLS
70121000 LLS
70120500 LLS wire assy. To PWM
ELEVATION RACK
70281002 ELEVATION RISER ASSY.
70154600 ELEVATION BLOCK ASSY.
POWER CORD
70253100 9FT. POWER CORD ER CORD
ON / OFF SWITCH
70251100 ROCKER ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70159400 22 X 119 3/4 2PLY TREADBELT
(ZT) 70321600 NEW ZT 20"X112 1/4" TREADBELT
DECK
70157900 FLEX DECK
(ZT) 70324300 500ZT FLEX DECK
FRONT ROLLER
70255400 ADJ. FRONT ROLLER
70352200 NEW NUMBER FOR ROLLER
70190900 ROLLER SCREW 1/4-20 X 2 GRD5 ZINC
REAR ROLLER
70157400 REAR ROLLER
STRADDLE COVERS
70162110 STRADDLE COVER/ALUM. 54 1/2"
(ZT) 70343700 500ZT STRAD. CVRS. RT.&LT.
(ZT) 70334000 500ZT STRAD CVR FRONT CAP Rt (Bullet lt (Bullet
70334100 500ZT STRAD CVR FRONT CAP LT (Bullet RT(bullet)
Page 49
70030900 DBL SIDE STICK TAPE 3/8 X 1/16 X 108FT
70243400 BLUE TAPE-STR. CVR. 1/2 X 150FT. ROLL
70086700 6X1 SRADDLE COVER SCREW
RAMRAILS
70330800 LEFT RAM RAIL
70330900 RIGHT RAM RAIL
PEDESTAL
70325000 PEDESTAL- WELDMENT/ROUNDED
(ZT) 70336900 500ZT PEDESTAL WELMENT
70304200 pedestal screw for zt
70156900 RUBBER WEAR STRIP FOR BASE-PED.
FRAME
70262401 FRAME WELDMENT/RND. ADJ. ROLLER
(ZT) 70322800 500ZT FRAME WLD/RND. ADJ. FR. ROLL
70155200 BUMPER FEET
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 50
CONTROL PANEL PART # DESCRIPTION
70237419 540 NON CONTROL BOARD
70237421 540 P CONTROL BOARD
70237420 540 HRC CONTROL BOARD
70237614 540 CI CONTROL BOARD
70290110 540non overlay
70289310 540p overlay
70289410 540hrc overlay
70290310 540ci overlay
70177400 SAFETY KEY ASSY.
70150000 SAFETY SWITCH
PWM
70132500 MOTOR CONTROLLER (PWM)
70013500 SCREW, 10-32x3/8 PPH TFS Bo
SPEED SENSOR
70243200 SPEED SENSOR
70243300 SCREW 4-40x1/4 PPH SELF TAPPING
DATA CABLE
70337900 540NON, P DATA CABLE
70337800 540 HRC DATA CABLE
70337700 540 CI DATA CABLE
70104000 SCREW #10x1/2 PPH
DRIVE MOTOR
70325500 3HP. DRIVE MOTOR
70125700 SCREW 10-32x1/4 PPH TFS Bo
70155200 BUMPER FEET 1 1/8 x1 1/2
70176000 3/8 Dbl Coated foam tape Tesa -49
70013500 SCREW10-32x1/4 PPH TFS Bo
70125500 5/16-18 NYLOC NUT
70115200 WASHER 3/8 1Dx7/8odx.083F
70125600 5/16-18x2 CARRIAGE BOLT
DRV BELT
70006300 POLY-V-BELT DRIVE BELT
ELEVATION MTR
70113200 ELEVATION MOTOR
540P, HRC, CI
(NON Z)
PARTS LIST
Page 51
70115500 CLEVIS PIN 3/8x1 1/2
70116700 COTTER PIN 1/16 Dia x 1 5/16
70013500 SCREW 10-32 x 3/8 PPH TFSBO
70118900 TORQUE ARM SWIVEL PIN
LLS
70121000 LLS
70125700 SCREW - 10-32x 1/4 PPH TFS BO
70120500 LLS WIRE ASSY. To PWM
ELEVATION RACK
70281003 ELEV. RISER ASSY.
70154600 ELEV. BLOCK ASSY.
70122800 SOCKET HD. CAP SCREWS 1/4-20x1
70183200 INCLINE START CAPACITOR
70013500 SCREW FOR CAP./10-32x3/8
POWER CORD
70253100 POWER CORD 12* 14/3 SJTW BLACK STRT
70125700 SCREW 10-32x1/4 PPH TFS Bo
ON / OFF SWITCH
70251100 ROCKER ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70290000 BELT 22x119 3/4 ST E5 2Ply-Lo
70289900 540 ORTHO TREADBELT
DECK
70288900 FLEX DECK
70020200 SCREW 10/32 x 1 1/4 PPH "F"
70158600 BELT GUIDE
70019300 SCREW 10x3/4
FRONT ROLLER
70275200 ADJ. FRONT ROLLER
70157000 WASHER INTERNAL TOOTH STAR 1/4 id
70185300 NYLOC NUT 1/4-10 2 nc
70190900 HEX BOLT-TAP1/4-20x2 Grd 5/21NC
70256800 FLAT WASHER .50x.26x.09 2n Pltd.
REAR ROLLER
70275500 REAR ROLLER ASSY.
70159000 INTERNAL TOOTH WASHER 5/16
70158900 BOLT HEX HEAD TAP, Grd 5-5/16
STRADDLE COVERS
70263900 Straddle cover / Plastic
Page 52
70030900 TAPE, 3/8x1/16x108ft. DBL stick-49
70243400 BLUE TAPE -STR. CVR. 1/2x150ft roll
70086700 6X1 DRYWALL SCREW
RAMRAILS
70274105 CHR RAM RAIL
70210600 #10x3/4 PPH TEK Screw-bo
70280600 NON CNR RAILS(RAM)
PEDESTAL
70288600 PEDESTAL- WELDMENT/ROUNDED
70156900 RUBBER WEAR STRIPS
FRAME
70289700 FRAME WELDMENT/RND. ADJ. FRONT
70155200 BUMPER FEET
70020200 SCREW 10/32x1 1/4
70019300 SCREW 10x3/4 PPHSMBO
70086700 6x1 DRYWALL SCREW
AUTO WAXER
70280800 AUTO WAXER
70019300 SCREW 10x3/4 PPHSMS Bo
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 53
CONTROL PANEL PART # DESCRIPTION
(540Z's) Overlay only 70292410 540Z CI Overlay only
(540ZT's)Overlays only 70327510 540ZT P Overlay Only
70327511 540ZT HRC Overlay Only
(540ZT'S)BOARDS 70328013 540ZT P CONTROL BOARD ONLY
ONLY 70328012 540ZT HRC CONTROL BOARD ONLY
70298612 540 Z CI CONTROL BOARD
540ZT EX'S BOARDS 70328053 540ZT PEX CONTROL BOARD ONLY
ONLY International 70328052 540ZT HRCEX CONTROL BOARD ONLY
ALL 540ZT PANEL 70328102 540Z,ZT P PANEL
ARE THE SAME 70328201 540Z,ZT HRC PANEL
AS THE REG, 70299201 540Z,ZT CI PANEL
540Z
70298900 PANEL SCREW
70331000 MAGNET SAFETY KEY
70290602 Panel Back Cover
OVERLAY
PWM
70132500 PWM MOTOR CONTROLLER
540 ZT SERIES 70342900 540 ZT MOTOR CONTROLLER
70013500 PWM SCREW
SPEED SENSOR
70243200 CIRCUIT BOARD SPEED SENSOR
70243300 SPEED SENSOR SCREW
DATA CABLE
ALSO FOR 540ZT 70341300 540ZT 20 pin Data Cable (Most ZT's)
70337900 540Z,ZT P DATA CABLE
70337800 540Z,ZT HRC DATA CABLE 6pin & 8pin
70337700 540Z,ZT CI DATA CABLE 2 pin & 8 pin
DRIVE MOTOR
70325500 3HP. DRIVE MOTOR
70341500 540ZT DRIVE MOTOR
70125700 Screw 10-32x1/4 PPH TFS Bo
70155200 BUMPER FEET 1 1/18 X 1 1/2
70176000 3/8 DBL. COATED FOAM TAPE
540Z, ZT, P, HRC, CI
PARTS LIST
Page 54
70013500 Screw 10-32x1/4 PPH TFS Bo
70125500 5/16-18 NYLOC NUT
70115200 WASHER 3/8 ID X 7/8 OD
70125600 5/16-18X2 CARRIAGE BOLT
DRV BELT
70006300 210J10 DRIVE BELT
ELEVATION MTR
70113200 ELEVATION MOTOR
70115500 3/8 X 1 1/2 CLEVIS PIN
70116700 COTTER PIN
70013500 Screw 10-32 x 3/8 PPH TFSBO
70118900 TORQUE ARM SWIVEL PIN
LLS
70121000 LLS
70120500 LOWER LIMIT SWITCH WIRE
ELEVATION RACK
(ZT) 70281003 540ZT ELEVATION RISER ASSY.
70154600 ELEVATION BLOCK ASSY.
POWER CORD
70253100 POWER CORD 9FT.
ON / OFF SWITCH
70251100 ROCKER ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70290000 540Z TREADBELT-22 X 108 3/4
70289900 540Z TREADBELT-22 X 108 3/4 Ortho
(ZT) 70321800 540ZT-22"X112 1/4" TREADBELT
zt 70321900 540ZT ORTHO BELT
DECK
70288900 540Z FLEX DECK
(ZT) 70324400 540ZT FLEX DECK
FRONT ROLLER
70275200
ADJ. FRONT ROLLER
70352400 NEW NUMBER ADJ. FRONT ROLLER Page 55
REAR ROLLER
70275500 REAR ROLLER
STRADDLE COVERS
70263900 STRADDLE COVER/ALUM. 54 1/2" 55
(ZT) 70343700 540ZT PLASTIC STRAD. CVRS.
70327002 Plastic Insert
70343901 540ZT Alum Side Covers
70030900 3/8X1/16X108FT ROLL DBL. SIDE STICK T
70243400 BLUE TAPE - STR. CVR. 1/2X150FT. ROLL
70329600 SILVER sst tape
70086700 STRADDLE COVER SCREW
RAMRAILS
70330800 LEFT RAM RAIL
70330900 RIGHT RAM RAIL
PEDESTAL
70325100 PEDESTAL-WELDMENT/ROUNDED
(ZT) 70337000 540ZT PEDESTAL WELDMENT
FRAME
70289701 FRAME WELDMENT/ROUNDED ADJ. RO
(ZT) 70322900 540ZT FRAME WELDMENT/RND.
70155200 BUMPER FEET
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET
Page 56
PART # DESCRIPTION
CONTROL PANEL
550 Board Only 70237519 550P Board Only
70237518 550HRC Board Only
70237610 550CI Board Only
70279200 550OP/ P DOT/ PANEL
70279100 550HRC DOT/PANEL
70279000 550CI DOT/PANEL
OVERLAY
70279201 550OP/ P DOT/OVERLAY
70279101 550HRC DOT/ OVERLAY
70150000 Safety Switch Assembly
70279001 550CI OVERLAY
PWM 70132500 MOTOR CONTROLLER
70183500 550ci pwm
SPEED SENSOR
70243200 CIRCUIT BOARD SPEED SENSOR
DATA CABLE
70337900 550 P INTERFACE CABLE
70337800 550 HRC INTERFACE CABLE
70337700 550 CI INTERFACE CABLE
DRV MTR
70325500 3HP DRIVE MOTOR
DRV BELT
70006300 210J10 POLY-V-BELT
ELEVATION MTR
70113200 ELEVATION MOTOR
LLS
70121000 LOWER LIMIT SWITCH
ELEVATION RACK
70281003 ELEVATION RISER ASSY.
POWER CORD
70253100 9FT. POWER CORD
70008200 STRAIN RELIEF BUSHING
ON/OFF SWITCH
70251100 ON/OFF ROCKER SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70276800 22X119 3/4" 2PLY TREADBELT
550CI BELT 70276900 22x119 3/4" 2PLY TREADBELT ORTHO
DECK
70276700 FLEX DECK
FRONT ROLLER
70352400 ADJ. FRONT ROLLER
REAR ROLLER
Page 57
550P, HRC
PARTS LIST
70352000 REAR ROLLER
STRADDLE COVERS
70162109 LT. AND RT.ALUM. STRADDLE COVER
PEDESTAL
70277600 PEDESTAL-WELDMENT/ROUNDED
FRAME
70276000 ADJ. FR. ROLLER FRAME/WELDMENT
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 58
PART # DESCRIPTION
CONTROL PANEL
BOARD ONLY 70298217 550Z P BOARD ONLY
550Z ONLY 70298218 550Z HRC BOARD ONLY
70298613 550Z CI BOARD ONLY
70292415 550Z P OVERLAY
70334400 550Z P PANEL
70334500 550Z HRC PANEL
70329900 550Z CI PANEL
70331000 MAGNET SAFETY KEY
PWM
70132500 PWM MOTOR CONTROLLER
70013500 PWM SCREW
SPEED SENSOR
70243200 CIRCUIT BOARD SPEED SENSOR
70243300 SPEED SENSOR SCREW
DATA CABLE
70337900 550Z P DATA CABLE
70337800 550Z HRC DATA CABLE
70337700 550Z CI DATA CABLE
DRIVE MOTOR
70325500 3HP DRIVE MOTOR
DRV BELT
70006300 210J10 DRIVE BELT
ELEVATION MTR
70113200 ELEVATION MOTOR
70183200 ELEV. MTR. START CAPACITOR
70115500 3/8 X 1 1/2 CLEVIS PIN
70116700 1/16 DIA X 1 5/16 COTTER PIN
70013500 Screw 10-32 x 3/8 PPH TFSBO
70118900 TORQUE ARM SWIVEL PIN
LLS
70121000 LLS
70120500 LOWER LIMIT SWITCH WIRE
ELEVATION RACK
70281003 ELEVATION RISER ASSY.
70154600 ELEVATION BLOCK ASSY. Page 59
550Z, P, HRC, CI
PARTS LIST
POWER CORD
70253100 POWER CORD 9FT.
ON / OFF SWITCH
70251100 ROCKER ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70276800 22X119 3/4 2PLY TREADBELT
70276900 Belt Seig 22x119 3/4 550 Ortho
DECK
70276700 FLEX DECK
FRONT ROLLER
70352400 ADJ. FRONT ROLLER
REAR ROLLER
70352000 REAR ROLLER
STRADDLE COVERS
70162110 STRADDLE CVR/ALUM 54 1/2"
70030900 3/8X1/16X108FT. DBL. STICK TAPE
70243400 1/2X150FT ROLL BLUE TAPE
70086700 6X1 STRADDLE COVER SCREW
RAMRAILS
70330800 LEFT RAM RAIL
70330900 RIGHT RAM RAIL
CARRIAGE ASSY. 550Z CI
70240900 ADJ. MOTOR ASSY 550Z CI
70241100 COVER PAN-WELDMENT
70239200 SHAFT
70250700 LIMIT SWITCH ASSY.-STOP 550CI
70249900 S.O.F.T. SELECT POWER CABLE
70280000 INTERFACE CABLE-ASSY.550Z CI
70280400 ADJ. CARRIAGE ASSY. 550Z CI
70252300 CIRCUIT BOARD INTERFACE 550Z CI
PEDESTAL
70325104 PED-WELDMENT/ROUNDED HRC
70325105 PED-WELDMENT/ROUNDED P
FRAME
70276000 FRAME WELDMENT/RND-ADJ ROLLER
70155200 BUMPER FEET
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 60
PART # DESCRIPTION
CONTROL PANEL
(550ZTX's) Overlay only 70292415 550ZTX P Overlay only
70292413 550ZTX HRC Overlay only
70292414 550ZTX CI Overlay Only
Control Board Only 70298216 550ZTX P CONTROL Board Only
70298215 550ZTX HRC CONTROL Board Only
70298611 550ZTX CI CONTROL Board Only
International Version 70298256 550ZTX PEX CONTROL Board Only
70298255 550ZTX HRCEX CONTROL Board Only
70298651 550ZTX CIEX CONTROL Board Only
Panel Assy. 70299007 550ZTX P CONTROL PANEL
70298707 550ZTX HRC CONTROL PANEL
70329900 550ZTX CI CONTROL PANEL
PWM
70342900 MOTOR CONTROLLER
Speed Sensor
70243200 Speed Sensor
DATA CABLE
500zt 70341300 DATA CABLE HRC
DRV MTR
70341500 3HP 10 MPH DRIVE MOTOR
70293002 MOTOR COVER
DRV BELT
70006300 210J10 POLY-V-BELT
ELEVATION MTR
70330100 INCLINE MOTOR ASSY
LLS
70309401 LOWER LIMIT SWITCH
70120501 LOWER LIMIT SWITCH WIRE TO PWM
ELEVATION RACK
70329300 INCLINE RACK ASSY
POWER CORD
70253100 9FT POWER CORD
70008200 STRAIN RELIEF BUSHING
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
Page 61
550 ZTX, P, HRC, CI
PARTS LIST
TREADBELT
70322000 22"X124" TREADBELT
70322100 ORTHO BELT FOR THE 550ZTX CI AND O
DECK
70324500 FLEX DECK
70232700 Bumper
FRONT ROLLER
70352400 ADJ. FRONT ROLLER
REAR ROLLER
70352000 REAR ROLLER
STRADDLE COVERS
70343800 ALUM. STRADDLE COVER RH & LH
RAMRAILS
70330800 LH RAM RAIL
70330900 RH RAM RAIL
70347500 INTERCHANGABLE RAM RAILS RT.&LT.
PEDESTAL
70325302 PEDESTAL WELDMENT - ARCHED 550ztx hrc
FRAME
70337100 FRAME WELDMENT
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 62
Model 600-750
Parts List
600, P, HRC Page 64
600Z / 700Z, P, HRC Page 67
700, P, HRC (SS100-SS90) Page 70
700A, P, HRC Page 73
725 P, HRC Page 76
750, P, HRC, CI Page 79
Page 63
PART # DESCRIPTION
CONTROL PANEL
(600) Board Only 70237412 600NON Board Only
70237411 600P Board Only
70237410 600HRC Board Only
70269900 600NON DOT PANEL 00-PRESENT
70269901 600P DOT PANEL 00-PRESENT
70150000 SAFETY SWITCH ASSY.
70182800 SAFETY KEY ASSY.
OVERLAY
70269910 600NON DOT OVERLAY 00-PRESENT
70269911 600P DOT OVERLAY 00-PRESENT
70265011 600HRC DOT OVERLAY 00-PRESENT
PWM
70219200 MOTOR CONTROLLER SS-92 DCI
70219201 MOTOR CONTROLLER 02-PRESENT
70013500 PWM SCREW
SPEED SENSOR
70243200 CIRCUIT BOARD SPEED SENSOR
70243300 SPEED SENSOR SCREW
DATA CABLE
70337900 NON HRC DATA CABLE
70337800 P DATA CABLE
DRV MTR
70325500 3HP DRIVE MOTOR
70282700 MOTOR CHOKE ASSY.
70125500 NYLOCK NUT- 5/16-18 DRIVE MTR.
70125600 CARRIAGE BOLT -5/16-18 X 2 3/4
DRV BELT
70006300 210J10 POLY-V-BELT
ELEVATION MTR
70113200 ELEVATION MOTOR
70115500 CLEVIS PIN 3/8 X 1 1/2
70118900 TORQUE ARM SWIVEL PIN
70116700 COTTER PIN 1/16 DIA. X1 5/16
70183200 ELEVATION START CAPACITOR
70013500 CAPACITOR SCREW 10-32 3/8 PPH
LLS
70121000 LOWER LIMIT SWITCH
Page 64
600P, HRC
PARTS LIST
70125700 10-32 X 1/4 PPH SCREW
70120500 LOWER LIMIT SWITCH WIRE TO PWM
ELEVATION RACK
70281002 ELEVATION RISER ASSY.
70154600 ELEVATION BLOCK ASSY.
70122800 1/4-20 X 1 SOCKET HD. CAP SCREW
POWER CORD
70282900 12 FT. POWER CORD
70303700 NEMA PLUG
ON / OFF SWITCH
70251100 ROCKER ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70159400 20" X 108" 2 PLY SEIGLING TREADBELT
DECK
70157900 FLEX DECK
70020200 DECK SCREW 10/32 X 1 1/4
BUMPER KIT
70155200 BUMPER FEET
70020200 10/32 X 1 1/4 PPH SCREW
70232700 FLEX BUMPER
70086700 BUMPER SCREW 6 X 1
FRONT ROLLER
(ADJUSTABLE) 70255400 ADJ. FRONT ROLLER
70188500 BOLT - ADJ. FR.
70185300 NYLOCK NUT - ADJ. FR.
70256800 FLAT WASHER
70190900 BOLT - FR. SOLID MOUNT END / ADJ. FR
REAR ROLLER
70157400 REAR ROLLER
70158900 REAR ROLLER BOLT
70159000 INTERNAL TOOTH WASHER 5/16
STRADDLE COVERS
70162101 STRADDLE COVERS RT. & LT. ALUM.
70086700 6 X 1 DRYWALL SCREW
70030900 DBL. STICK TAPE 3/8 X 1/16 X 108FT.
70243400 BLUE TAPE 1/2 X 150FT.
RAMRAILS
70274101 HANDLEBAR ASSY./ RAM - CHR
70210600 #10 X 3/4 PPH TEK SCREW
Page 65
REHAB RAILS
70274401 REHAB HANDRAIL ASSY. - CHR
REHAB HARDWARE
70157000 WASHER - INTERNAL STAR
70013500 SCREW 10-32 X 38 PPH
70104000 SCREW # 10 X 1/2 PPH TEK
70122800 SCREW 1/4-20 X 1 SOCKET HEAD CAP
70064500 PLASTIC PLUG
PEDESTAL
70264600 WELDED PEDESTAL 600 NON-CI
70155900 SCREW PED / 1/4-20 X 5/8
70157000 INTERNAL TOOTH STAR WASHER / PED
70269800 BOTTLE HOLDER / MOLDED PLASTIC
70019300 SCREW - BOTTLE HOLDER
FRAME
70262401 FRAME WELDMENT/ROUNDED ADJ. RO
AUTO WAXER
70280800 600 AUTO WAXER ASSY.
70019300 10 X 3/4 PPHSMS SCREW
70239800 REPLACEMENT WAX CHANNEL ASSY.
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 66
PART # DESCRIPTION
CONTROL PANEL
(600Z's) Overlays only 70327510 600Z NON/P Overlay Only
70327511 600Z HRCEX OVERLAY
Board Only 600Z 70328011 600Z NON Control Board Only
70328010 600Z P
International 70328051 600Z HRCEX Control Board Only
(700Z's) Overlays only 70292412 700Z Overlay only
70292411 700Z P Overlay only
70292413 700Z HRC Overlay only
Board Only 700Z 70298412 700Z NON Control Board Only
70298214 700Z P Control Board Only
70298213 700Z HRC Control Board Only
International 70298452 700Z NONEX Control Board Only
70298254 700Z PEX Control Board Only
70298253 700Z HRCEX Control Board Only
70290601 PANEL,BOTTOM CONSOLE
70294301 PANEL LF. HANDLEGRIP LOWER
70294302 PANEL RT. HANDLEGRIP LOWER
PWM
70343000 220 VOLT PWM
70342900 MOTOR CONTROLLER
SPEED SENSOR
70243200 CIRCUIT BOARD SPEED SENSOR
DATA CABLE
70341300 20 PIN DATA CABLE
DRV MTR
70260800 220 MOTOR
70341500 3HP 115V DRIVE MOTOR
DRV BELT
70006300 210J10 POLY-V-BELT
ELEVATION MTR
70260800 220 ELEVATION MOTOR
70113200 ELEVATION MOTOR
Page 67
600Z/ 700Z, P, HRC
PARTS LIST
LLS
70121000 LOWER LIMIT SWITCH
ELEVATION RACK
70281002 600Z ELEVATION RISER ASSY.
70281003 700Z ELEVATION RISER ASSY.
POWER CORD
70303700 12' POWER CORD
ON / OFF SWITCH
70251100 ON/OFF ROCKER SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70317300 600Z 20"X108" TREADBELT
70317400 700Z 22"X119 3/4" TREADBELT
DECK
70157900 600Z FLEX DECK
70276700 700Z FLEX DECK
FRONT ROLLER
70352200 600Z ADJ. FRONT ROLLER
70352400 700Z ADJ. FRONT ROLLER
REAR ROLLER
70351800 600Z REAR ROLLER
70352000 700Z REAR ROLLER
STRADDLE COVERS
70162111 600Z ALUM.STRADDLE CVRS.
70162110 700Z ALUM. STRADDLE COVERS
RAMRAILS
70330800 LH RAM RAILS
70330900 RH RAM RAILS
Page 68
PEDESTAL
70325100 PEDESTAL WELDMENT
FRAME
70262405 600Z WLD/RND ADJ. ROLLER FRAME
70276003 700Z FRAME W/ ADJ. FR. ROLLER
AUTO WAXER
70280800 AUTOWAXER
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Replacement Pedestal 70325103!
Page 69
PART # DESCRIPTION
CONTROL PANEL
(SS100) 70119300 700NON SS100 PANEL 95-96
70119900 700P SS100 PANEL 95-96
70179700 700HRC SS100 PANEL 95-95
(97-98 STYLE) 70132412 700NON SS90 Control Board Only 97-98
Board Only 70132411 700P SS90 Control Board Only 97-98
70132410 700HRC SS90 Control Board Only 97-98
(99-PRESENT) 70237515 700NON 15% DOT Control Board Only 99-Z
(DOT Control Board) 70237514 700P 15% DOT Control Board Only 99-Z
70237513 700HRC 15% DOT Control Board Only 99-Z
70185400 HEART RATE RECEIVER
70138500 POLAR CHEST STRAP-HEART RATE
70273800 CONTACT H R TRANSMITTER
70182800 SAFETY SWITCH ASSY. 700
70209700 PUSH BUTTON SAFETY SWITCH SS90 TON SAFETY SWITCH SS90
OVERLAY
(SS100 STYLE) 70119301 700NON SS100 OVERLAY 95-96
70119901 700P SS100 OVERLAY 95-96
70179701 700HRC SS100 OVERLAY 95-96
(97-98 STYLE) 70160815 700NON SS90 OVERLAY 97-98
70160816 700P SS90 OVERLAY 97-98
70160814 700HRC SS90 OVERLAY 97-98
(99-PRESENT) 70242310 700NON DOT OVERLAY 99-PRESENT
70242311 700P DOT OVERLAY 99-PRESENT
70242312 700HRC DOT OVERLAY 99-PRESENT
PWM
(SS100) 70113900 (SS100) MOTOR CONTROLLER
(96-800000-) 70219200 PWM MOTOR CONTROLLER
(PRESENT)
SPEED SENSOR
(SS90 STYLE-98-) 70162402 SPEED SENSOR SS90
Page 70
700P, HRC
(SS100-SS90)
PARTS LIST
(99-PRESENT) 70243201 SPEED SENSOR 700, P, HRC
DATA CABLE
70337900 700, P DATA CABLE
70337800 700 HRC DATA CABLE
DRV MTR
70325600 DRIVE MOTOR 3HP W/FLYWHEEL
70263500 220V DRIVE MOTOR
70155300 DRIVE PULLEY 1 11/16" DIA.
70146500 DRIVE PULLEY 12MPH
DRV BELT
70127600 DRIVE BELT 260J10 POLY-V-BELT
ELEVATION MTR
70171500 ELEVATION MOTOR 115V 700, P, HRC
(HARDWARE) 70126200 INCLINE BEARING (FLANGED)
70118900 SWIVEL PIN/TORQUE ARM
70115500 CLEVIS PIN 3/8 DIA. 1 1/2 IN. LONG
70116700 HAIR COTTER PIN .062 DIA.
70022600 SET SCREW, INCLINE, CONE POINT
LLS
70121000 LOWER LIMIT SWITCH
70018100 CHERRY SWITCH
70120500 LOWER LIMIT SWITCH WIRE
ELEVATION RACK
(BEFORE AUG99) 70176700 MOLDED WHEEL 3/8 BEF.AUG.99
70003100 WHEEL BOLT 3/8 BEFORE AUG, 99
AFTER AUG., 99) 70176701 MOLDED WHEEL 2 1/4 AFT.AUG, 99
70174300 WHEEL BOLT 1/2" AFTER AUG., 99
POWER CORD
70282900 POWER CORD 12 FT.
70008200 STRAIN RELIEF BUSHING
ON / OFF SWITCH
70251100 ON/OFF SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
TREADBELT
70214300 TREADBELT 700, P, HRC
DECK
Page 71
70158000 DECK
70086700 DECK SUSP. BLOCK SCREW6X1
70020200 DECK SCREWS 10/32X1 1/4"
FRONT ROLLER
70150800 FRONT ROLLER ASSY, 700 W/SS100
(NON-ADJ.) 70164700 FRONT ROLLER 8 MAGNET/NON ADJ
(ADJ. NOV.-00) 70265300 FRONT ROLLER ADJ.-NOV.2000
70005600 ROLLER SCREW 3/8-16X3/4
70005500 ROLLER BOLT 3/8X16X3 HX HD. BOLT
REAR ROLLER
70186000 REAR ROLLER SS90
70005600 ROLLER SCREW 3/8-16X3/4
70005500 ROLLER BOLT 3/8X16X3 HX HD. BOLT
70073900 OLD STYLE
STRADDLE COVERS
70162107 STRADDLE COVER-ALUM.-46 13/16"
70030901 3/8 X1/16 X 36YD. DBLE STK TAPE 16'
RAMRAILS
70204200 RAMRAIL HANDLE BAR
70104000 RAIL SCREWS #10-32X3/8
PEDESTAL
70233500 PEDESTAL-99-00 700,700P,700HRC
70207800 BOLT - PED 3/8" - 16 X 3/4"
AUTO WAXER
70167000 AUTOWAXER - ASSY
70239800 WAX CHANNEL (ONLY)
70342000 GRND. WIRE FOR WAXER
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 72
WEIGHT PART # DESCRIPTION
70298413 700A NON Board Only
70237517 700A P Board Only
70237516 700A HRC Board Only
70311700 700A DOT PANEL ASSY.
70312100 700A P DOT PANEL ASSY.
70312000 700A HRC DOT PANEL ASSY.
70240505 EXTRUSION PANEL CLIP28 3/4" LG
70020300 SCREW 6-32x3/8 PPHMS BLK OX
70182800 SAFETY SWITCH
70242313 700A DOT /OVERLAY
70279201 700A P DOT/OVERLAY
70279101 700A HRC DOT/OVERLAY
3lbs. 70219200 MOTOR CONTROLLER 5592/DCI (Green)
70219201 MOTOR CONTROLLER (02)
70013500 SCREW, 10-32x3/8 PPH TFS Bo
70282700 CHOKE ASSY.
1lbs. 70243200 SPEED SENSOR
70243300 SCREW 4-40x1/4 PPH SELF TAPPING
70337900 NON HRC DATA CABLE
70337800 AP, HRC
44lbs. 70325500 3HP. DRIVE MOTOR
70125700 SCREW 10-32x1/4 PPH TFS Bo
70176000 3/8 DBL. COATED FOAM TAPE TESA -49
70013500 SCREW 10-32x1/4 PPH TFS Bo
70125500 5/16-18 NYLOC NUT
70115200 WASHER 3/8 1Dx7/8odx.083F
70125600 5/16-18x2 CARRIAGE BOLT
Page 73
700A, P, HRC
PARTS LIST
70006300 DRIVE BELT
10lbs. 70113200 ELEVATION MOTOR
70183200 INCLINE START CAPACITOR
70013500 SCREW FOR CAP. /10-32x3/8
70115500 CLEVIS PIN 3/8x1 1/2
70116700 COTTER PIN 1/16 Diaz x 1 5/16
70013500 SCREW 10-32 x 3/8 PPH TFSBO
70118900 TORQUE ARM SWIVEL PIN
70121000 LLS
70125700 SCREW - 10-32x 1/4 PPH TFS BO
70120500 LLS WIRE ASSY. To PWM
26lbs. 70281003 ELEV. RISER ASSY.
70122800 SOCKET HD. CAP SCREW 1/4-20x1
70303700 POWER CORD 12* 14/3 SJTW Black STRT
70125700 SCREW 10-32x1/4 PPH TFS Bo
70013500 SCREW 10-32x3/8 PPH TFS Bo
70251100 ROCKER ON/OFF SWITCH
70017200 15 AMP CIRCUIT BREAKER
9lbs. 70317400 BELT 22x119 3/4 ST E5 2Ply-Lo
60lbs. 70276700 FLEX DECK
70020200 SCREW 10/32 x 1 1/4 PPH "F" z1
70158600 BELT GUIDE
70019300 SCREW 10x3/4
9lbs. 70275200 ADJ. FRONT ROLLER
70352400 NEW NUMBER ADJ. FRONT ROLLER
70157000 INTERNAL TOOTH STAR WASHER 1/4 id
70185300 NYLOC NUT 1/4-10 2 no
70256800 FLAT WASHER .50x.26x.09 2n Plod.
13lbs. 70275500 REAR ROLLER ASSY.
70159000 INTERNAL TOOTH WASHER 5/16
Page 74
70158900 BOLT HEX HEAD TAP, Gird 5-5/16
70162109 STRADDLE COVER/ALUM. 54 1/2" 55
70031200 TAPE 1/2"x18yd. Adhesive
70030900 TAPE, 3/8x1/16x108ft. DBL stick-49
70243400 BLUE TAPE -STR. CVR. 1/2x150ft roll
70086700 6x1 DRYWALL SCREW
70274105 CHR RAM RAIL
70280600 NON CHR RAIL (ram)
70210600 #10x3/4 PPH TEK Screw-boo
70277601 PEDESTAL- WELDMENT/ROUNDED
70156900 RUBBER WEAR STRIPS
70276003 FRAME WLDMNT.
70155200 BUMPER FEET
70020200 SCREW 10/32x1 1/4
70019300 SCREW 10x3/4 PPHSMBO
70086700 6X1 DRYWALL SCREW
1lbs. 70280800 AUTO WAXER
70019300 SCREW 10x3/4 PPHSMS Bo
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 75
PART # DESCRIPTION
CONTROL PANEL
(98 STYLE) 70132412 725 NON CONTROL Board Only-SS90 (98)
Board Only 70132411 725P CONTROL Board Only-SS90 (98)
70132410 725HRC CONTROL Board Only-SS90 (98)
(99-00 STYLE) 70237512 725 NON DOT CONTROL Board Only (99-00)
Board Only 70237511 725P DOT CONTROL Board Only (99-00)
70237510 725HRC DOT CONTROL Board Only (99-00)
70182800 SAFETY KEY ASSY.
70185400 HEART RATE RECEIVER
70138500 HEART RATE POLAR CHEST STRAP
70239800 HEART RATE TRANSMITTER
70245100 PLASTIC COVER -HR CONTROL
OVERLAYS
(98 STYLE) 70160815 725 NON OVERLAY-SS90 (98)
70160816 725P OVERLAY-SS90 (98)
70160814 725HRC OVERLAY-SS90 (98)
( 99- 00 STYLE) 70242310 725 NON DOT/OVERLAY (99-00)
70242311 725P DOT/OVERLAY (99-00)
70242312 725 HRC DOT/OVERLAY (99-00)
PWM
70219200 MOTOR CONTROLLER 5592/DCI(Green)
70219201 MOTOR CONTROLLER WITH CHOKE (02)
70013500 SCREW, 10-32x3/8 PPH TFS Bo
70282700 CHOKE ASSY.
SPEED SENSOR
70243201 SPEED SENSOR
70243300 SCREW 4-40x1/4 PPH SELF TAPPING
DATA CABLE
70337900 725, P DATA CABLE
70337800 725 HRC DATA CABLE
DRV MTR 70325800 MED. MOTOR
Page 76
725P, HRC
PARTS LIST
70325600 DRIVE MOTOR 3 HP.
70125700 MOTOR SCREW
70125600 CARRIAGE BOLT 5/16-18X2"
70125500 NYLOC NUT-5/16-18
70115200 WASHER-3/8 ID. X 7/8 OD.
70219601 MOTOR ISOLATION KIT (725)
DRV BELT
70127600 DRIVE BELT 260J10
ELEVATION MTR
70171500 INCLINE MOTOR (HUBBLE)
(HARDWARE) 70183600 CLEVIS PIN 3/8 X 1 3/4
70118900 SWIVEL PIN - TORQUE ARM
70183200 START CAPACITOR
70013500 CAPACITOR SCREW 10-32X3/8
LLS
70121000 LOWER LIMIT SWITCH
70125700 LOWER LIMIT SWITCH SCREW
70120500 LOWER LIMIT TO PWM WIRE
ELEVATION RACK
70281002 ELEVATION RACK
70122800 ELEV. SCREW 1/4-20X1 SOCKET HEAD
70116900 LOCK NUT 1/4-20 ZINC/COURSE-THREAD
70176700 MOLDED WHEEL 3/8 BEF. AUG., 99
70003100 MOLDED WHEEL BOLT BEF. AUG., 99
70176701 MOLDED WHEEL 1/2 AFTER AUG., 99
70174300 MOLDED WHEEL BOLT AFTER AUG., 99
POWER CORD
70282900 12 FT. POWER CORD
ON / OFF SWITCH
70251100 ON/OFF SWITCH
CIRCUIT BREAKER
70017200 CIRCUIT BREAKER 15 AMP
70213100 CIRCUIT BREAKER 10 AMP DUAL POLE
TREADBELT
70214400 SEIGLING TREADBELT E5X20X129
DECK
70159100 FLEX DECK
70020200 DECK AND BUMPER FEET SCREW
70155200 DECK BUMPER FEET
FRONT ROLLER
(BEFORE NOV.00) 70164700 FRONT ROLLER BEFORE NOV.,00
Page 77
(AFTER NOV.00) 70265300 FRONT ROLLER AFTER NOV.,00-ADJ.
70207800 ROLLER SCREW 3/8-16X3/4
70283700 ROLLER BOLT 3/8-16X3 LG.
70115200 ROLLER WASHER 3/8 IDX7/8 OD
70253700 3/8 NYLOC NUT
REAR ROLLER
70186000 REAR ROLLER
70188600 REAR ROLLER BOLT
STRADDLE COVERS
70162106 STRADDLE COVER
70086700 STRADDLE COVER SCREW
70030900 STRADDLE COVER TAPE-108FT.DBL.STK.
70243400 STRADDLE COVER BLUE TAPE150 FT.
RAMRAILS
70274101 RAM RAILS CONTACT HEART RATE
70210600 RAIL SCREW #10X3/4
PEDESTAL
70233501 PEDESTAL-WELDED
70156900 RUBBER WEAR STRIP
70207800 BOLT - PED. 3/8"-16 X 3/4"
70269800 BOTTLE HOLDER MOLDED PLASTIC
70019300 BOTTLE HOLDER SCREW 10X3/4
AUTO WAXER
70167000 AUTO WAXER
70019300 SCREW 10x3/4 PPHSMS BO
70342000 GROUNDING STRAP ASSY.
70239800 WAX CHANNEL (ONLY)
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 78
PART # DESCRIPTION
(99-PRESENT) 70237524 750 BOARD ONLY 99-PRESENT
BOARD ONLY 70237525 750P BOARD ONLY 99-PRESENT
70237613 750CI BOARD ONLY 99-PRESENT
GRAY MACHINES ONLY! 70219310 750 P Board Only
BOARD ONLY 70176910 750CI Board Only
70185400 HRC RECEIVER
70245100 PLASTIC HR COVER
70182800 SAFETY KEY/SWITCH
OVERLAY
(98 STYLE) 70216212 750NON OVERLAY 1998
70216211 750P OVERLAY 1998
70177011 750CI OVERLAY 1998
(99-PRESENT) 70242510 750NON DOT OVERLAY 99-PRESENT
70242511 750P DOT OVERLAY 99-PRESENT
70242610 750CI DOT OVERLAY 99-PRESENT
PWM
70183500 MOTOR CONTROLLER-BEFORE 08/00
70183502 PWM WITH CHOKE-AFTER-08/00
70264800 MOTOR CONTROLLER- 220V
70013500 10-32X3/8 SCREW (PWM)
SPEED SENSOR
70243201 CIRCUIT BOARD SPEED SENSOR
70243300 4-40 X 1/4 SELF TAPPING SCREW
DATA CABLE
Verify config. 70286700 750, P DATA CABLE BEFORE 08/00
70337700 750 CI DATA CABLE
Verify config. 70219500 750 non, p data cable '99
Verify config. 70271700 750B & PB DATA CABLE '00
DRV MTR
70172000 3HP DRIVE MOTOR Core charge added
70263400
3HP DRIVE MOTOR EX 220V Core charge added
70169600 DRIVE MOTOR TENSION PLATE
70159000 5/16 STAR WASHER
Page 79
750P, HRC, CI
PARTS LIST
70125700 10-32X1/4 SCREW
70219701 MOTOR ISOLATION KIT (750)
DRV BELT
70127600 260J10 POLY-V-BELT
TREADBELT
70214500 TREADBELT/SIEGLING E5X23X129
DECK
70169400 DECK 32 1/2 X 56
70020200 DECK SCREW 10 X 1 1/4
70183400 DECK BUMPER
ELEVATION MTR
70171500 HUBBLE ELEVATION MOTOR
(HARDWARE) 70183200 CAPACITOR-LIFT MOTOR
70183600 3/8 X 1 3/4 CLEVIS PIN
70118900 TORQUE ARM SWIVEL PIN
70013500 10-32 X 3/8 SCREW
70116700 1/16DIA. X 15/16 COTTER PIN
LLS
70121000 LLS
70125700 10- 32 X 1/4 Screw for LLS Bracket
70120500 LLS TO PWM WIRE
ELEVATION RACK
70281004 ELEVATION RISER ASSY.
70154600 ELEVATION BLOCK ASSY.
70122800 1/4-20 SOCKET HEAD CAP SCREW
70173900 MACHINED WHEEL 2 1/4" OD.
70174300 WHEEL BOLT 1/2" X 1 SHOULDER BOLT
POWER CORD
70282900 12 FT. POWER CORD
70008200 STRAIN RELIEF BUSHING
ON / OFF SWITCH
70251100 ON/OFF ROCKER SWITCH
CIRCUIT BREAKER
70017200 15 AMP CIRCUIT BREAKER
FRONT ROLLER
70168000 NON ADJ. FRONT ROLLER
70265400 ADJ. FRONT ROLLER
70207800 SCREW 3/8-16 X 3/4
REAR ROLLER
70168300 REAR ROLLER
70170800 1/2- 13 X 4" TAP BOLT
Page 80
70170900 1/2INTERNAL TOOTH STAR WASHER
STRADDLE COVERS
70171800 RT. AND LT. STRADDLE COVER
70243400 BLUE TAPE, STR CVR 1/2 X 150 FT ROLL
70086700 6 X 1 DRYWALL SCREW
70030900 DOUBLE STICK TAPE 3/8 X 1/16 X 108 Ft
RAMRAILS
70165100 RAM HANDLE BAR
70210600 #10 X 3/4 SCREW
PEDESTAL
70233601 ROUNDED PEDESTAL WELDMENT
70156900 RUBBER WEAR STRIP
70269800 BOTTLE HOLDER
70019300 BOTTLE HOLDER SCREW 10X3/4
FRAME
70227501 FRAME WELDMENT/ROUNDED GRAY
70155200 BUMPER FEET
70020200 BUMPER FEET SCREWS
70164500 BUMPON DECK BUMPER
AUTO WAXER
70167000 AUTOWAXER
70019300 AUTOWAXER SCREW, 10 X 3/4
70342000 GROUNDING STRAP ASSY.
WAX CHANNEL
LUBRICATION
70348900 LUBE STICK
70349000 SILICONE PACKET (1 APPLICATION)
Page 81

Navigation menu