Tunstall Healthcare 6460402 Radio Pull Cord type 64604/02 User Manual Installation guide

Download:
Mirror Download [FCC.gov]
Document ID	488560
Application ID	323GvvWcoV+6mrTZfwGFVg==
Document Description	Installation guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	147.82kB (1847718 bits)
Date Submitted	2004-11-16 00:00:00
Date Available	2004-11-16 00:00:00
Creation Date	2004-10-25 11:59:00
Producing Software	Acrobat 5.0 Image Conversion Plug-in for Windows
Document Lastmod	2004-10-25 12:01:08
Document Title	Installation guide
Document Creator	Acrobat 5.0 Image Conversion Plug-in for Windows

312MHz Radio Pullcord (Supervised) Installation Guide
This guide is for use with Tunslall Radic- Pullcord 64604/02
Confirm Functionality and Compatibility
The Radio Pullcord is a radio transmitter device activated by pulling an integral cord.
it is designed for installation into flushmount, recessed wall boxes- typically oiCarlon or m5 manufacture Viilh 3.3 inch mounting
centres.
Installation
a) Operate the power switch on the rear ofthe Pulicbrd using a narrow, but blunt, nun-conductive item (cg cocktail stick) Take care
not to damage components on the circuit board below.
b) Fix the puilcord to the recessed, flush mount back box (note if particularly damp environments are to cxisl for appreciable time.
then a impervious seal (cg silicone bead) is recommended to be provided.
c) Note that the pullcnrd must be mounted away from electrically conductive surfaces/ materials to ensure no impairment of radio
range. Walls might typically be plasterboard but should not be foil backed.
c) Program the puilcord into the appropriate Personal Emergency Response System (PERS). The PERS should be placed into radio
programming mode and a pullcord transmission initiated. Complete any configuration if necessary (cg non plug and play systems)
Refer to the relevant advanced user or programming guide
d) Test the installation by activating the associated equipment either via a test button or raising a full alarm condition,
l. Images
Not yet available
Label Interpretation
The product and packaging have a small labcl containing a bar codc,
This bar code (code 123) contains (reading left to right):
6 digits, decimal to represent the radio identity; 1 digit to represent the product type (=3 for Pullcord); 1 digit
chcoksum. (Eye readable version is printed undemealh)
Additionally on the label is the pan numbcr and issue (top right) and the week and year ufmanul'aclulc (bottom Icli)
On the packaging there is a larger label and barcndc.
This bar code contains:
a digit serial number (being week number, year, sequential serial), 7 digit pflrl number, 2 digits issue (Eye readable
version is printed underneath)
D6408033A draft Page 1 of2
Specification
Battery life: 10 years with over 25 operations per day.
Battery Monitoring; The battery status is also communicated to the PERS Equipment. The battery is checked upon manual activation or
within the supervision cycle,
Radio Range: 120 metres free space
Weight: 100grams.
Supervision interval: Every 4 hours a supervision transmission is made. The battery is checked at the same time. No indication of
transmission is given. (i.e 6 transmissions per day)
Environment: intended operating temperature between 0 to +40 Celsius.
Frequency: 312.000Ml—lz.
Programming: Plug and play (automatically configuring Pullcord product type) on compatible 34 bit systems only.
I. Approvals and Statements
Federal Communicltions Commission (FCC) notices
This equipment has been tested and found to comply with the limits [or a Class B digital device, pursuant to part 15 ofthe
FCC Rules. These limits are designed to provide reasonable prolcclion against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instmctions, may cause harmful interference to radio communications. However. there is no guarantee
that interference will not occur in a particular installation. lfthis equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more ofthe following measures:
- Reorient or relocate the receiving antenna,
- increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which thc receiver is connected,
0 Consult Ihc dealer or an experienced radio/TV technician for help.
312 Radio Pullcord (Part Number 64604/01) FCC ID: GZX-6460402
This Device complies with Pan 15 ofthc FCC Rules. Operation is subject to the following two conditions: (I) ‘l' s dcvicc
may not cause harmful interference, and (2) This device must accept any interference reserved, including interference that
may cause undesired operation. Warning Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment
Industry Cilmldl Notice This equipment meets the applicable Industry Canada Equipment Technical Spccit'lcation: 'l lt
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration w -
performed based on a Declaration ofConformity indicating that Industry Canada technical specifications were met. It does
not imply that industry Canada approved the equipment.
Service
This product contains no user serviceablc parts,
This product contains a lithium battery which must be disposed ofin suitable facilitics- do not incincralc.
It is recommended that regular testing of the system is carried out.
Development ftlename
K:\Systems and Produc|s\USA 312 Peripherals\phase l\design-pullmrd\d64080331! doc
Drafi Nas last save- 29/09/04 15:51
D8408033A draft Page 2 of2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2004:10:25 12:01:08+01:00
Create Date                     : 2004:10:25 11:59:00+01:00
Creator                         : Acrobat 5.0 Image Conversion Plug-in for Windows
Page Count                      : 2
Mod Date                        : 2004:10:25 12:01:08+01:00
Creation Date                   : 2004:10:25 11:59:00+01:00
Producer                        : Acrobat 5.0 Image Conversion Plug-in for Windows
Metadata Date                   : 2004:10:25 12:01:08+01:00

EXIF Metadata provided by EXIF.tools