Turbosound Tcs C35T Users Manual C Quickstart V1.0
TCS-C35T - Quick Start Guide TCS-C35T - Quick Start Guide
TCS-C50T - Quick Start Guide TCS-C50T - Quick Start Guide
TCS-C35T to the manual 041a4136-f543-4629-ac5b-4845124d4c8f
2015-02-03
: Turbosound Turbosound-Tcs-C35T-Users-Manual-460661 turbosound-tcs-c35t-users-manual-460661 turbosound pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Quick Start Guide TCS-C ceiling series Models covered by this Quick Start Guide TCS-C35T, TCS-C50T ceiling speakers. Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further information about this or any other TURBOSOUND product, please contact us. A detailed user manual on this product is available from our web site at www.turbosound.com. TCS-35T Tweeter Terminal cover plate Strain relief fitting Tap selector LF loudspeaker Attachment screws Rotating mounting tabs Input connector Strain relief fitting TCS-50T Terminal cover plate Tap selector Tweeter Steel fire can LF loudspeaker Rotating mounting tabs Attachment screws Unpacking the TCS series loudspeaker After unpacking the unit please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of future re-shipment. System Requirements TCS-C series ceiling loudspeakers are passive loudspeaker systems, and require only one amplifier channel for correct operation, the frequency splitting between the LF driver and the HF driver being accomplished by the internal passive crossover network. Using Ceiling Loudspeakers with Subwoofers If subwoofers are required, additional amplifier channels and external electronic crossovers will be required. The Turbosound LMS series digital management systems are recommended for this purpose. TCS-C series Quick Start Guide - Page - 1 Quick Start Guide TCS-C ceiling series Amplifier Considerations Turbosound ceiling speakers should be driven by high quality power amplifiers designed for true professional use. Amplifiers should be capable of delivering long term broadband power equal to the loudspeaker’s program power rating at the stated nominal impedance. Always operate your power amplifiers at maximum gain for the best headroom and signal/noise ratio, controlling the overall system volume from the mixing console. The use of under-powered amplifiers must be avoided as heavily clipped signals can cause permanent loudspeaker damage. In a distributed system the amplifiers must be capable of supplying broadband power equivalent to the sum of the power rating of the loudspeakers (taking into account the individual power taps selected) connected to that particular amplifier channel. Installation Procedure 1. Cut a hole in the ceiling tile using a circular cutter set the size listed below and pull the wiring through the hole. TCS-C35T cut-out diameter is 215mm TCS-C50T cut-out diameter is 240mm 2. Connect the wiring to the removable connector. A 4-way Phoenix-style connector is supplied with the loudspeaker. Strip the insulation back by 5mm (3/16”), insert the bare ends of the wire into the connector (do not tin the wire) and screw down the hold-down screw with a small flat blade screwdriver. 3. There are two possible connection strategies, depending on the desired circuit result when a single unit is disconnected for trouble shooting or servicing: Parallel Input Terminals. This allows the circuit to remain intact whenever a speaker is disconnected. Connect the outgoing pair of wires to the same terminals as the incoming pair of wires. Inp Link - + + - Power Amplifier + - Input Link Input Link Input Link - + + - - + + - - + + - Speaker 1 Speaker 2 Speaker 3 Loop-through Terminals. All loudspeakers after this unit will be disconnected, helping to isolate problems to a section of the distributed line while leaving the wires connected to the connector. Inp Link - + + - Power Amplifier TCS-C series Quick Start Guide - Page - 2 + - Input Link Input Link Input Link - + + - - + + - - + + - Speaker 1 Speaker 2 Speaker 3 Quick Start Guide TCS-C ceiling series 4. The mounting hardware consists of two tile rails and a ‘C’ plate (these are supplied with the TCS-C35T, and as an optional accessory for the TCS-C50T). Insert the tile rails through the hole in the ceiling tile and align them parallel to each other on either side of the hole, and with the ends positioned over the ceiling T grid. Insert the ‘C’ plate through the hole and snap the tabs onto the tile rails as shown. Position directly over the hole in the ceiling tile and secure with the fixing screws supplied. Note that the provision of multiple fixing holes in the tile rails allows the speaker to be positioned away from the centre of the tile if desired. 5. Plug the connector into the socket in the loudspeaker’s terminal cup. The connector is polarised to avoid the possibility of mis-connection. The terminal cover also acts as the strain relief. Rotate the cover and tighten the retaining screw. 6. Connect the safety tab to a separate support point. Consult construction codes in your region. 7. Insert the speaker into the ceiling and secure the fixing arms. Offer the loudspeaker into the ceiling until the back of the front baffle rim touches the ceiling tile. Turn the attachment screws to tighten the fixing arms. Note that the first 1/4 turn rotates the arm outwards and subsequent turns tighten the tab down onto the ceiling tile. DO NOT OVERTIGHTEN. 15 V 70 30 16 30 15 V 100 60 7.5 16 15 7.5 V 100 V 70 16 completed for all loudspeakers. 15 30 grilles off until final adjustment of the tap selectors has been 30 16 the grille. In some installations it may be preferable to leave 60 located on the front baffle, and should be adjusted before fitting TCS-35T 7.5 TCS-50T 3.75 8. Adjust the voltage tap selector for desired level. The selector is 9. Apply the logo badge to the grille in the desired location if required, and fit the loudspeaker grille by pressing the grille firmly into place until it is flush with the rim. Painting before Installation The loudspeaker’s white finish matches most décor schemes and does not need further finishing. However where interior design requires an alternative colour this can be easily accomplished. The loudspeaker can either be painted before installation, or where the rim needs to be finished at the same time as the ceiling the rim can be painted after locating in the ceiling. The speaker will accept almost any type of emulsion or oil-based paint. Two coats are recommended. Clean the rim and grille with a light solvent such as white spirit. Do not use gasoline, kerosene, acetone, MEK, paint thinner, harsh detergents or other chemicals, all of which may damage the loudspeaker. After cleaning, apply two coats of paint, using a roller or brush, or by spraying. Painting the Speaker with the Ceiling Using the paint shield provided, paint the speaker and remove the shield. To paint the grille, first remove the logo and grille cloth backing. It is advisable to spray the grille to avoid the mesh becoming clogged with paint from a roller or brush, which may impair the sound quality. Replace the grille cloth and the logo. TCS-C series Quick Start Guide - Page - 3 Quick Start Guide TCS-C ceiling series Technical Specifications TCS-C35T TCS-C50T 235mm (9.2”) dia x 112mm (4.4”) deep 268mm (10.5”) dia x 83mm (3.3”) deep 100mm (3.9”) minimum mounting depth 206mm (8.1”) minimum mounting depth Hole cut-out 215mm (8.5”) 240mm (9.5”) Net weight 2.3kg (5.1lbs) 3.4kg (7.5lbs) Components 1 x 3.5” (89mm) LF driver 1 x 5” (127mm) LF driver 1 x 1” (25mm) HF tweeter 1 x 1” (25mm) HF tweeter Frequency response 100Hz – 20kHz ±4dB 75Hz – 22kHz ±4dB Nominal dispersion 150ºH x 150ºV @-6dB points 180ºH x 180ºV @-6dB points Sensitivity 85dB (half space), 1w @ 1m 92dB (half space), 1w @ 1m Power handling 30 watts r.m.s., 60 watts program 75 watts r.m.s., 150 watts program Maximum SPL 100dB continuous, 106dB peak 110dB continuous, 116dB peak Transformer taps 30W, 15W, 7.5W (100 volt line) 60W, 30W, 15W (100 volt line) 30W, 15W, 7.5W, 3.75W (70 volt line) 60W, 30W, 15W, 7.5W (70 volt line) Nominal impedance 16 ohms nominal (low impedance) 16 ohms nominal (low impedance) Construction Paintable injection moulded ABS Paintable injection moulded ABS Grille Powder coated perforated steel backed Powder coated perforated steel backed with acoustic cloth with acoustic cloth Connector Phoenix 4-way connector Phoenix 4-way connector Protection Thermal fuse disconnects speaker from Thermal fuse disconnects speaker from distributed system distributed system Conforms to BS5839 part 8 1988 and Conforms to BS5839 part 8 1988 and IEC/EN 60849 fire prevention IEC/EN 60849 fire prevention Dimensions Standards Spares and Accessories LS-50 5” low frequency loudspeaker LS-35 3.5” low frequency loudspeaker TW-52 1” high frequency tweeter PX-TCS-C50T Passive crossover network PX-TCS-C35T Passive crossover network MG-C50 Metal grille MG-C35 Metal grille TCS-CTR Tile rail (supplied with TCS-C35T, optional for TCS-C50T) TCS-CCP35 C plate for TCS-C35T (supplied with TCS-C35T) TCS-CCP50 C plate for TCS-C50T (optional accessory for TCS-C50T) Turbosound Ltd., Star Road, West Sussex RH13 8RY, UK tel: +44 (0)1403 711447 fax: +44 (0)1403 710155 www.turbosound.com version 1.0 05/10 TCS-C series Quick Start Guide - Page - 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2010:07:16 15:46:53+01:00 Create Date : 2010:07:16 15:46:53+01:00 Format : application/pdf Title : Microsoft Word - TCS-C Quickstart v1.0 Creator : martinr Document ID : uuid:8c9cabc5-dc1f-4c80-b39b-ace0aa21c8fd Instance ID : uuid:fe46ea34-fdea-43ee-b3aa-79d35286c07d Page Count : 4 Author : martinrEXIF Metadata provided by EXIF.tools