Tyco Safety Canada 005132 WIRELESS RECEIVER User Manual pc5132 433 v3 12 in im eng 29004754 r002

Download:
Mirror Download [FCC.gov]
Document ID	85093
Application ID	ZjuqN42ObInWUhRGu8X9TA==
Document Description	Installation Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.46kB (180780 bits)
Date Submitted	2000-02-03 00:00:00
Date Available	2001-06-04 00:00:00
Creation Date	1910-00-20 11:03:21
Producing Software	Acrobat Distiller 3.0 for Windows
Document Lastmod	2000-02-01 10:37:00
Document Title	pc5132-433 v3-12 in im eng 29004754 r002
Document Creator	Adobe PageMaker 6.5
Document Author:	neumannl

• W A R N I N G •
This manual contains information on limitations regarding
product use and function and information on the limitations as to
liability of the manufacturer.
Installation
Manual
PC5132-433
Please see page ii for a description of new
features for the PC5132-433 v3.12.
Version 3.12
WARNING
Please Read Carefully
Note to Installers
This warning contains vital information. As the only individual in
contact with system users, it is your responsibility to bring each
item in this warning to the attention of the users of this system.
System Failures
This system has been carefully designed to be as effective as
possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide
protection. Any alarm system of any type may be compromised
deliberately or may fail to operate as expected for a variety of
reasons. Some but not all of these reasons may be:
■ Inadequate Installation
A security system must be installed properly in order to provide
adequate protection. Every installation should be evaluated by a
security professional to ensure that all access points and areas
are covered. Locks and latches on windows and doors must be
secure and operate as intended. Windows, doors, walls, ceilings
and other building materials must be of sufficient strength and
construction to provide the level of protection expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or police department is highly
recommended if this service is available.
■ Criminal Knowledge
This system contains security features which were known to be
effective at the time of manufacture. It is possible for persons
with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain
effective and that it be updated or replaced if it is found that it
does not provide the protection expected.
■ Access by Intruders
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through
an area of insufficient coverage, disconnect a warning device, or
interfere with or prevent the proper operation of the system.
■ Power Failure
Control units, intrusion detectors, smoke detectors and many
other security devices require an adequate power supply for proper
operation. If a device operates from batteries, it is possible for
the batteries to fail. Even if the batteries have not failed, they
must be charged, in good condition and installed correctly. If a
device operates only by AC power, any interruption, however
brief, will render that device inoperative while it does not have
power. Power interruptions of any length are often accompanied
by voltage fluctuations which may damage electronic equipment
such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure
that the system operates as intended.
■ Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The
expected battery life is a function of the device environment,
usage and type. Ambient conditions such as high humidity, high
or low temperatures, or large temperature fluctuations may reduce the expected battery life. While each transmitting device
has a low battery monitor which identifies when the batteries
need to be replaced, this monitor may fail to operate as expected.
Regular testing and maintenance will keep the system in good
operating condition.
■ Compromise of Radio Frequency
(Wireless) Devices
Signals may not reach the receiver under all circumstances which
could include metal objects placed on or near the radio path or
deliberate jamming or other inadvertent radio signal interference.
■ System Users
A user may not be able to operate a panic or emergency switch
possibly due to permanent or temporary physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is important that all system users be trained in
the correct operation of the alarm system and that they know
how to respond when the system indicates an alarm.
■ Smoke Detectors
Smoke detectors that are a part of this system may not properly
alert occupants of a fire for a number of reasons, some of which
follow. The smoke detectors may have been improperly installed or positioned. Smoke may not be able to reach the smoke
detectors, such as when the fire is in a chimney, walls or roofs,
or on the other side of closed doors. Smoke detectors may not
detect smoke from fires on another level of the residence or
building.
Every fire is different in the amount of smoke produced and
the rate of burning. Smoke detectors cannot sense all types of
fires equally well. Smoke detectors may not provide timely
warning of fires caused by carelessness or safety hazards such
as smoking in bed, violent explosions, escaping gas, improper
storage of flammable materials, overloaded electrical circuits,
children playing with matches or arson.
Even if the smoke detector operates as intended, there may be
circumstances when there is insufficient warning to allow all
occupants to escape in time to avoid injury or death.
■ Motion Detectors
Motion detectors can only detect motion within the designated
areas as shown in their respective installation instructions. They
cannot discriminate between intruders and intended occupants.
Motion detectors do not provide volumetric area protection.
They have multiple beams of detection and motion can only
be detected in unobstructed areas covered by these beams.
They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material
on the lenses, mirrors, windows or any other part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes
in temperature. However their effectiveness can be reduced when
the ambient temperature rises near or above body temperature
or if there are intentional or unintentional sources of heat in or
near the detection area. Some of these heat sources could be
heaters, radiators, stoves, barbeques, fireplaces, sunlight, steam
vents, lighting and so on.
■ Warning Devices
Warning devices such as sirens, bells, horns, or strobes may
not warn people or waken someone sleeping if there is an
intervening wall or door. If warning devices are located on a
different level of the residence or premise, then it is less likely
that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such
as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however
loud, may not be heard by a hearing-impaired person.
■ Telephone Lines
If telephone lines are used to transmit alarms, they may be out of
service or busy for certain periods of time. Also an intruder may
cut the telephone line or defeat its operation by more sophisticated means which may be difficult to detect.
■ Insufficient Time
There may be circumstances when the system will operate as
intended, yet the occupants will not be protected from the emergency due to their inability to respond to the warnings in a
timely manner. If the system is monitored, the response may
not occur in time to protect the occupants or their belongings.
■ Component Failure
Although every effort has been made to make this system as
reliable as possible, the system may fail to function as intended
due to the failure of a component.
■ Inadequate Testing
Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested weekly and
immediately after a break-in, an attempted break-in, a fire, a
storm, an earthquake, an accident, or any kind of construction
activity inside or outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating
devices and any other operational devices that are part of the
system.
■ Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is
not a substitute for property owners, renters, or other occupants to act prudently to prevent or minimize the harmful effects of an emergency situation.
Table of Contents
Introduction
1.1
1.2
1.3
1.4
PC5132 Set up & Wiring
2.1
2.2
2.3
2.4
10
Test the Reception of Wireless Devices ........................................................... 10
Mount the PC5132 and Wireless Devices ........................................................ 11
Additional Notes
6.1
6.2
6.3
Program Zones and Partitions ............................................................................ 7
Enable PC5132 Supervision ............................................................................... 7
Enable Supervision of Wireless Zones ............................................................... 8
Jamming Signal Detection .................................................................................. 8
PC5132 Software Default .................................................................................... 9
Deleting Wireless Devices .................................................................................. 9
Testing & Mounting
5.1
5.2
A Note about Electronic Serial Numbers ............................................................ 4
Enrolling Wireless Devices (WLS904NB433, WLS907NB433) .......................... 4
Enroll & Program Wireless Keys (WLS909NB433) ............................................. 5
Identified Wireless Keys ..................................................................................... 6
Other Programming
4.1
4.2
4.3
4.4
4.5
4.6
Unpack the PC5132 ............................................................................................ 3
Choose a Mounting Location for the PC5132 .................................................... 3
Antennas ............................................................................................................. 3
Connect the PC5132 Receiver ........................................................................... 3
Enrolling Wireless Devices
3.1
3.2
3.3
3.4
How to use this Manual ....................................................................................... 1
Specifications and Features ............................................................................... 1
Compatible Wireless Devices ............................................................................. 2
Batteries .............................................................................................................. 2
12
Trouble Conditions ............................................................................................ 12
Jamming Signal Detection ................................................................................ 12
Wireless Zone Low Battery Transmission ......................................................... 12
Troubleshooting
13
Programming Worksheets
14
Index
18
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could
void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in
strict accordance with the manufacturer’s instructions, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for Class B device in accordance
with the specifications in Subpart “B” of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference in any residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to television or radio reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the FCC helpful: “How to
Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S.
Government Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4.
T
hank you for purchasing the PC5132 Wireless Receiver. This product
is the result of several years of development and will allow you to connect
up to 8 wireless detection devices to the PC585, PC1565 and PC5008,
and up to 32 detection devices to the PC5015.
The PC5132 uses 433 MHz. It provides several advantages:
• supervisory transmissions are sent every 12 minutes, as opposed to every
50-60 minutes
• programmable supervisory window can be as little as one hour, or as long
as 24 hours
• devices use standard alkaline batteries as opposed to specialized
batteries
• diversity antenna arrangement for better RF reception
In addition, the PC5132 features:
• 6 digit serial numbers for all wireless devices: These new serial
numbers include hexadecimal digits. Please read Section 3.1 “A note on
Electronic Serial Numbers (ESN)” for more information on enrolling 6-digit
devices.
This product introduces these new features:
• Wireless key support: Up to sixteen WLS909NB433 wireless keys can be
enrolled.
• RF jamming detection: Two different RF jamming detection sensitivity
settings.
We are confident you will find the PC5132 Wireless Receiver a unique and useful
control panel enhancement.
Introduction
This manual describes how to install, program and maintain the PC5132.
Before you install the PC5132 module, you should have completed the following
steps in your system installation:
1. Plan the installation and wiring of the security system (see your system
Installation Manual)
2. Install the control panel, and install and enroll at least one keypad to use
for programming.
3. Install and enroll any hardwired zone expander modules (PC5108) you
plan to use.
NOTE: PC5108 zone expander modules occupy zones in 2 groups of 4 (e.g.
zones 9-12 and zones 13-16). None of the zones assigned to a PC5108 module
may be used for wireless devices.
Program the PC5132 from a system keypad or using downloading software on
a remote computer (e.g. DLS-1). Read your system Installation Manual for more
information.
1.1 How to use this Manual
Read this manual before you begin installing the PC5132. To install and set up
the PC5132 and wireless devices, follow these steps. Refer to the sections listed
below.
1. Temporarily mount and wire the PC5132 module (see Section 2)
2. Enroll and program wireless devices (see Section 3)
3. Complete zone and other programming on the system (see Section 4)
4. Test the placement of all the wireless devices (see Section 5)
5. Permanently mount the PC5132 receiver and wireless devices (see
Section 5)
For additional information on trouble conditions, RF jamming signal detection
and battery replacement, see Section 6.
For help with troubleshooting, see Section 7.
1.2 Specifications and Features
•
•
•
•
•
Current Draw: 80 mA
Frequency: 433 MHz
Zones - receiver can receive signals from up to 32 wireless zones
Antenna - diversity design for enhanced performance
Supervisory - programmable supervisory window, 1 to 24 hours, in 15
minute increments
• Location
- can be wired up to 750 ft. / 230 m from the main panel with 22 gauge wire
- connects to Keybus
- for longer wire runs, thicker gauge wire must be used.
• Compatibility: The PC5132 v3.12 can be connected to the following
panels: PC501X, PC5008, PC1565, PC585
I
1.3 Compatible Wireless Devices
Please refer to the Instruction sheets of the following devices for more information.
The PC5132 v3.12 can receive signals from the following devices:
• WLS904NB433 Motion Detector
• WLS907NB433 Universal Transmitter
• WLS909NB433 Wireless Key
1.4 Batteries
The wireless devices are designed to use only Energizer Alkaline batteries (by
Eveready).
NOTE: Do not use other brands of batteries. Using any other brand may affect
system operation.
PC5132 Set up & Wiring
This section describes how to set up and wire the PC5132 module.
2.1 Unpack the PC5132
Check that the following parts are in your PC5132 package:
· PC5132 PCB
· PC5132 plastic cabinet
2.2 Choose a Mounting Location for the PC5132
NOTE: Mount the PC5132 receiver and wireless devices after you have done
placement tests with the wireless devices (see sections 5.1 and 5.2).
Find a place that is:
• Dry
• Central to the proposed placement of all wireless devices
• As high as possible
• Far from sources of interference, including: electrical noise such as
computers, televisions and electric motors in appliances and heating and
air conditioning units; large metal objects like heating ducts and plumbing
which may shield the antenna.
Make sure that electrical wires will not run over the antenna(s) of the module
when it is mounted.
When mounting the PC5132 in a basement, place the module as high and as
close to the underside of the first floor as possible. The range of the module will
be reduced if the unit is mounted below ground level.
2.3 Antennas
The antennas have been installed at the factory.
They do not need any adjustment.
2.4 Connect the PC5132 Receiver
CAUTION: Remove all power from the system while connecting modules to the
Keybus.
Connect the PC5132 to the four-wire
Keybus of the control panel according
to the following diagram.
After you have completed the wiring,
reconnect the power to the security
system.
Now that you have wired the PC5132,
you should enroll and program the
wireless devices. See section 3 for
instructions.
Enrolling Wireless Devices
This section describes how to enroll wireless devices (WLS904NB433,
WLS907NB433), and wireless keys (WLS909NB433). For more information on
these devices, read the instruction sheet included with each device.
3.1 A Note about Electronic Serial Numbers
An electronic serial number (ESN) is printed on the back of each wireless device.
ESNs are used to enroll the wireless devices with the PC5132 receiver.
In order to reduce the occurrence of wireless devices with the same serial
number, 6-digit serial numbers are now printed on the back of each wireless
device. The 6-digit serial numbers include hexadecimal digits. For instructions
on programming hexadecimal numbers, see your system Installation Manual,
section 4: How to Program.
NOTE: 6-digit serial numbers are only supported on the following control panels:
PC501X, PC5008, PC1565 and PC585 v2.0 and higher.
The WLS904NB433 and WLS907NB433 devices have both a 5-digit and a 6digit serial number printed on them. When connecting the PC5132 to a PC5015
v1.x panel, enter 5-digit serial numbers only. When connecting the PC5132 to
a PC5015 v2.x and higher, PC5008, PC1565 or PC585 panel enter the 6-digit
serial number.
3.2 Enrolling Wireless Devices (WLS904NB433,
WLS907NB433)
1. At a system keypad, enter [✱][8][Installer’s code] to go to the installer’s
programming section.
2. Enter programming section [804].
3. Enter the 2-digit number corresponding to the zone the device is to
occupy ([01] to [32]).
NOTE: Hardwired and wireless devices cannot be assigned to the same zone.
PC5108 zone expander modules occupy zones in 2 groups of 4 (e.g. zones 912 and zones 13-16). None of the zones assigned to a PC5108 module may be
used for wireless devices. For more information on zone assignment, consult
your system Installation Manual.
4. Enter the device’s ESN. Follow the instructions in section 3.1 above.
5. Record the serial number and the assigned zone number in the
programming worksheets in the back of this manual.
6. Continue with steps 3 - 5 until you have enrolled all wireless devices.
7. To exit press [#]. The device is now enrolled on the system.
NOTE: The devices will not work properly until you complete zone and partition
programming (see section 4).
W
3.3 Enroll & Program Wireless Keys (WLS909NB433)
For wireless keys to work on the system, you need to enroll them and then
program the function buttons. Wireless keys are not assigned to zones and
require no zone programming. You can enroll up to 16 wireless keys on the
system.
Enroll Wireless keys
1. At a system keypad, enter [✱][8][Installer’s code] to go to the Installer’s
Programming section.
2. Enter programming section [804].
3. Enter a 2-digit number [41]-[56] to assign the wireless key a slot. These
numbers correspond to wireless key numbers 01-16.
4. Enter the key’s ESN. The entry must be six digits. If an older key with a 5digit ESN is being enrolled, add the digit [0] to the beginning of the ESN.
(E.g. ESN=61234, enter 061234)
5. The key is now enrolled on the system. Record the serial number and the
assigned slot number in the programming worksheets in the back of this
manual.
6. Repeat steps 3 - 5 until all wireless keys have been enrolled.
7. (PC5015 only) By default, all wireless keys are assigned to Partition 1.
To assign keys to Partition 2, enable the appropriate options in
programming sections [91] and [92].
NOTE: A wireless key can only be assigned to one partition.
8. To exit press [#].
Program the WLS909NB433 Function Buttons
WLS909NB433 wireless keys have four programmable function buttons. You
must program a set of four functions for the buttons before any keys will work.
After the functions are programmed, when you press and hold one of the four
buttons for two seconds, the system will execute the programmed function.
For systems not using partitions: program the function buttons in section
[59]. All wireless keys will have the same four functions.
For systems using 2 partitions (PC5015 only): all wireless keys assigned to
Partition 1 will have the four functions programmed in section [59]. All wireless
keys assigned to Partition 2 will have the four functions programmed in section
[60]. For example, if function button 1 in Section [59] is programmed for Stay
arming, then pressing the first button on wireless keys assigned to Partition 1 will
Stay arm Partition 1.
NOTE: Wireless keys will not work when the partition they are assigned to is
being accessed for zone bypassing or programming.
1. At a system keypad, enter [✱][8][Installer’s code].
2. Enter programming section [804].
3. Enter programming section [59] for keys assigned to partition 1, or [60]
for keys assigned to partition 2.
W
4. For each of the 4 function buttons, enter the 2-digit number of the
function you want to select. See the programming worksheets for a list of
function key options.
5. Record your programming choices in the worksheets in the back of the
manual.
6. To exit press [#].
3.4 Identified Wireless Keys
Reporting by the system of openings/closings by individual wireless keys and
command output [✱][7] activation by wireless key buttons may be supported on
certain control panels. To do this, the system will reserve access codes 17 – 32
for wireless keys 01-16 respectively. You must program one access code for
each wireless key (using [✱][5] access code programming) for this feature to
work correctly.
NOTE: Program these access codes on the system after you have connected
the PC5132 to the Keybus (see section 2.4).
Refer to your system Installation Manual for information on access code
programming.
Opening/Closing By Wireless Key Reporting
NOTE: The Identified Wireless Key Closing option is only available with the
PC501X, PC5008, PC1565, PC585 v2.0 and higher by turning section [015] option
4 off.
To enable the reporting of openings and closings by identified wireless keys:
• Make sure the control panel is v2.0 or higher
• Program a valid access code for each key
• Program a closing and opening reporting code for each key’s access
code
• Turn off the Quick Arm option in section [015] option [4] of the control
panel programming
To ensure that an unidentified wireless key cannot disarm the system, turn off
section [017], option [1] (in the control panel programming). This option is
available in control panels with software version 2.1 or higher.
Command Output Activation
NOTE: The Identified Wireless Key Command Output Activation feature is only
available with the PC5010, PC5015, PC5008, PC1565 and PC585 v2.0 and higher.
To enable command output activation by wireless keys, ensure that:
• Make sure the control panel is v2.0 or higher
• Program a valid access code for each key
• Enable the PGM output attribute Requires Access Code for each PGM
output programmed as [✱][7][1-4] in sections [141] to [154].
Now that you have enrolled all the wireless devices, you will need to program
the system to work properly with the devices. See section 4 for more information.
Other Programming
4.1 Program Zones and Partitions
Now that you have enrolled the wireless devices, you should complete all zone
programming on the system. Although the exact programming required varies
depending on which control panel the PC5132 is connected to, you should
check that the following programming areas are completed correctly for each
wireless zone:
• Enable zones and/or assign zones to one or more partitions (programming
sections [201]-[209]).
• Program the definition for each zone (programming sections [001]-[004]).
• Enable the wireless zone attribute for each wireless zone (PC585, PC1565,
PC5008, PC501X v2.0 and up only) (sections [101]-[132]).
See your system Installation Manual, for more information on each of the above
programming sections.
4.2 Enable PC5132 Supervision
The control panel will supervise the PC5132 receiver via the Keybus after at
least one device has been enrolled on the module (see section 3.2 “Enrolling
Wireless Devices”).
To activate module supervision, after you enroll the first device(s):
1. Exit and then re-enter installer’s programming
2. Enter programming section [902].
The system will generate a General System Supervisory trouble if the module is
removed from the Keybus. If you need to remove the PC5132 module from an
existing system, you will have to disable supervision of the PC5132.
NOTE: Deleting all devices from the PC5132 or defaulting the PC5132 will cause
a PC5132 supervisory fault
To
1.
2.
3.
disable PC5132 supervision:
Disconnect the PC5132 from the Keybus
Enter [✱][8][Installer Code]
Enter [902]. The control panel will clear all supervision and re-scan the
system for connected modules. The scan will take approximately one
minute.
4. To exit press [#].
To review which modules the control panel is currently supervising:
1. Enter [✱][8][Installer’s Code]
2. Enter [903] to display all modules. On LED keypads, light [17] will
indicate that the PC5132 is present on the system. On LCD keypads,
scroll until the module name appears on the display.
3. To exit press [#].
If the PC5132 module does not show on the keypad, one of the following
conditions may be present:
• the module is not connected properly to the Keybus
• there is a problem with the Keybus wiring run
• the module does not have enough power
• no devices have been enrolled on the PC5132
O
4.3 Enable Supervision of Wireless Zones
NOTE: (for PC501X v1.x control panels only) In order for wireless zones to be
supervised, you must enable Double End of Line (DEOL) supervision in the
PC5015 control panel. For more information, refer to your Installation Manual.
NOTE: (PC501X, PC5008, PC1565, PC585 v2.0 and higher only) For wireless
supervision to work, you must enable the wireless zone attribute on all wireless
zones (sections [101] to [132], option [8] ON).
Wireless Supervisory Window
Each wireless zone (WLS904NB433 or WLS907NB433) will send a supervisory
signal every 12 minutes. If the receiver does not receive a signal within the time
programmed for the Wireless Supervisory Window, it will generate a supervisory fault.
To program the wireless supervisory window:
1. Enter [✱][8][Installer Code] to enter Installer Programming.
2. Enter [804] to enter the PC5132 Module Programming.
3. Enter section [81].
4. Enter the time period for the supervisory window. The window is
programmed in 15 minute increments. The default programming is 10
(x15minutes), which is equal to 150minutes (2.5 hours). Valid entries are
(04) - (96), equal to 1 - 24 hours.
5. To exit press [#].
Disable/Enable Zone Supervision
All wireless zones have supervision enabled by default. To disable supervision
for any zone, enter the following at any system keypad:
1. Enter [✱][8][Installer Code] to enter Installer Programming.
2. Enter [804] to enter the PC5132 Module Programming.
3. Enter sections [82], [83], [84] and [85]. Enable or disable supervision for
each wireless zone by turning each relevant option on or off.
4. To exit press [#].
4.4 Jamming Signal Detection
The PC5132 receiver detects jamming signals that can prevent the receiver
from properly receiving transmissions from enrolled devices. When jamming
signals are detected for 5 seconds, the control panel will generate a General
System Tamper trouble, which will be reported immediately. Jamming signal
detection is turned ON by default.
To turn OFF jamming signal detection:
1. Enter [✱][8][Installer Code] to enter Installer Programming.
2. Enter [804] to enter the PC5132 Module Programming.
3. Turn ON section [90], option [7].
4. To exit press [#].
O
RF Jamming Detection Sensitivity
There are two RF jamming detection settings for sensitivity: Normal and
Sensitive. Use the Sensitive setting for installations in rural areas, or for
installations where the zones are located at the far end of their range from the
PC5132 receiver. Use the Normal setting for all other applications.
To change the RF jamming detection sensitivity:
1. Enter [✱][8][Installer Code] to enter Installer Programming.
2. Enter [804] to enter the PC5132 Module Programming.
3. For Sensitive detection, turn ON section [90], option [6]. For Normal
detection, turn OFF section [90], option [6]. (Option is set to OFF by
default.)
4. To exit press [#].
4.5 PC5132 Software Default
Returning the PC5132 programming to factory default settings is a quick way to
remove all the enrolled devices from the system and reset all the programming
in section [804].
NOTE: Performing this procedure will not change any programming sections
except [804]. Resetting the control panel to factory default settings will not return the PC5132 module to factory default settings.
To restore the PC5132 programming to the factory default settings:
1. Enter [✱][8] [Installer’s Code].
2. Enter programming section [996].
3. Enter the Installer’s Code, followed by [996] again. The software for the
PC5132 will be restored to its factory default settings.
4. To continue programming the unit, exit installer’s programming by
pressing [#] and then re-enter installer’s programming by entering [✱][8]
[Installer’s Code].
For instructions on restoring the default programming of the control panel or any
other connected module, see your system Installation Manual.
4.6 Deleting Wireless Devices
To remove a wireless device from the system, follow the guideline for enrolling
a wireless device (see section 3.2). Program the ESN as [000000]. The wireless
device for the zone will be removed.
NOTE: You may need to remove power from the panel in order to clear troubles
caused by deleted zones.
Now that you have completed all PC5132 related programming, you can test
and mount the receiver and devices. See section 5 for more information.
Testing & Mounting
5.1 Test the Reception of Wireless Devices
It is very important to test the proposed placement of each wireless device before
it is mounted. Following these steps will test the signal strength between the
PC5132 and the wireless devices.
You can test all of the devices together (global placement testing) or test each
device individually. To test all the devices together, see Testing All Wireless
Devices Together. To test wireless devices individually, see Testing Individual
Devices.
NOTE: After you have enrolled the wireless devices, you must exit and then reenter installer’s mode at least once before you can perform a placement test.
Testing All Wireless Devices Together:
1. Temporarily put the WLS904NB433 and WLS907NB433 devices in the
places you want to mount them.
2. At a system keypad, enter [✱][8][Installer Code].
3. Enable the Global Module Placement test by entering section [804]. Then
enter sub-section [90] and turn on option [8].
4. Press [#] twice.
5. Enter programming section [904], then enter [01].
6. Activate one of the devices being tested until a result is displayed on the
keypad or sounded by the keypad or bell:
WLS904NB433: Remove the detector from the backplate and then
replace it. Once the detector is replaced on the backplate the panel will
show and/or sound the result of the placement test at the keypad.
WLS907NB433: Open the contact by moving the magnet away from the
unit. The keypad will show/sound the test result. After the first test result
has been generated (about 10 seconds) close the contact to generate
another test result. If the unit is attached to a door or a window, open and
close the door or window to activate the device.
WLS909NB433: Press any function key at several different locations.
Read the test results at the keypad:
Result
LED Keypad
LCD Keypad Buzzer/Bell
Good
Light 1 On Steady “Good”
1 Beep/Squawk
Fair
Light 2 On Steady “Fair”
2 Beeps/Squawks
Bad
Light 3 On Steady “Bad”
3 Beeps/Squawks
Activate the device until you get 3 good or fair results in a row.
You may mount WLS904NB433 and WLS907NB433 devices where
results were good or fair.
Devices indicating a bad result must be moved to another location. You
may only have to move the device a few inches to correct a bad result.
NOTE: Do not mount any device where a “bad” test result was indicated.
10
T
7. Go to the next device to be tested and activate it until the test result is
displayed/sounded.
NOTE: Wait until the placement test of one device is shown/sounded before
beginning to test the next device.
Continue to test the devices until both the PC5132 and the devices are in
good locations. If several wireless devices produce BAD test results, you
may need to move the PC5132 to a better location. (See section 2.2 for
tips on finding a location for the PC5132.)
8. To exit the placement test and return to installer programming, press [#]
twice.
Testing Individual WLS904NB433 and WLS907NB433 Devices:
1. Temporarily place the WLS904NB433 or WLS907NB433 you want to test
in the place you want to mount it.
2. At a system keypad, enter [✱][8][Installer Code].
3. Enter programming section [904].
4 Enter the 2-digit zone number for the device to be tested.
5. Activate the device being tested until a result is displayed on the keypad
or sounded by the keypad or bell. (Same as step 5 in the Global
Placement Test section, previous page.)
6. To test another device, press [#] once, then repeat steps 4 - 5. Continue
to test the devices until both the PC5132 and the devices are in good
locations.
If several wireless devices produce BAD test results, you may need to
move the PC5132 to a better location. (See section 2.2 for tips on finding
a location for the PC5132.)
7. To exit the placement test and installer programming, press [#] twice.
Testing Individual Wireless Keys:
You cannot use the individual device test described above to test WLS909NB433
wireless keys. To ensure that the PC5132 receiver is receiving transmissions
from the devices, use the function keys on the WLS909NB433 at several
different points in the installation.
5.2 Mount the PC5132 and Wireless Devices
When you have tested reception of the PC5132 with all the wireless devices (see
section 5.1) and you have a good mounting location, mount the PC5132:
1. Pull the Keybus wires through the hole at the bottom of the cabinet.
2. Mount the cabinet securely to the wall.
Mount the Devices
If you have conducted the placement test described in section 5.1 and got 3
“Good” or “Fair” results in a row for each device, you can mount the wireless
devices. See the Installation sheet for each device for mounting instructions.
Now that your PC5132 and wireless devices are mounted and working properly,
read section 6 for information on potential wireless trouble conditions, RF
jamming signals, and battery replacement.
11
Additional Notes
6.1 Trouble Conditions
The control panel always watches for possible trouble conditions. If a trouble
condition occurs, the keypad “Trouble” light will turn on and the keypad will
beep. Press [✱][2] to display the trouble conditions.
The following trouble conditions apply to the PC5132 and/or any enrolled
devices. For a description of all troubles, please see your system Installation
Manual.
• General System Tamper
• General System Trouble • Zone Tamper
• General System Supervisory • Device Low Battery
• Zone Fault
Tamper Switches
There are two tamper switches on the PC5132 board. Both removing the plastic
cover and/or removing the PC5132 from its mounting location will cause a
general system tamper.
6.2 Jamming Signal Detection
The PC5132 receiver detects jamming signals that can prevent the receiver
from properly receiving transmissions from enrolled devices. See section 4.4
“Jamming Signal Detection” for information on jamming signal detection programming.
6.3 Wireless Zone Low Battery Transmission
Within any transmission, the device will indicate the status of the battery. If a
battery is low, the system will indicate a Device Low Battery trouble.
The system will delay reporting the event to the central station for the number
of days programmed for Zone Low Battery Transmission Delay in section
[370]. This will prevent unnecessary reporting of the event if the user has been
instructed on how to replace batteries.
Replacing Batteries in Wireless Devices
1. Remove the cover of the device from its back plate. This creates a
tamper condition on the zone.
2. Refer to the battery installation instructions on the installation sheet of
each component. Be sure to note the proper orientation of the batteries
as you install them.
3. When the fresh batteries are in place, re-attach the cover to the back
plate. The tamper is restored and the zone sends a battery trouble
restoral signal to the PC5132. The battery trouble is now clear and the
device should function normally.
NOTE: When batteries in one device need to be replaced, the batteries in all
devices may need to be replaced at the same time.
12
Troubleshooting
1. When I enter the 2-digit zone number when adding a wireless
device, the keypad gives me a long beep.
You cannot enter ESNs unless a PC5132 wireless receiver is connected to the
Keybus. See section 2 for instructions on setting up and wiring the PC5132
module.
2. I have entered the ESN for the device but when I violate the
device, the zone does not show open on the keypad.
Check the following:
• Ensure the ESN has been entered correctly
• Ensure that the zone is enabled for the partition (if partition programming
is used).
• Ensure that the wireless zone is not assigned to a zone used by PC5108
modules, an on-board zone, or a keypad zone.
• Ensure that the zone is programmed for something other than “Null
Operation”, and that the wireless zone attribute is turned on.
3. When I try a module placement test I get no result or “Bad”
results.
Check the following (see sections 5.1 and 5.2 for more information on testing
devices):
• Verify that you are testing the correct zone
• Verify that the correct ESN was entered when the device was enrolled
• Verify that the device is in range of the PC5132. Try testing the device in
the same room as the receiver.
• Confirm that the PC5132 is properly connected to the Keybus (see section
2 for PC5132 set up and wiring instructions).
• Check that you are testing the zone correctly (see sections 5.1 and 5.2 for
testing instructions)
• Check that the batteries are working and installed correctly.
• Look for large metal objects that may be preventing the signal from
reaching the PC5132.
The device must be located where consistent “Good” results are obtained. If
several devices show “Bad” results, move the receiver. See section 2.2 for tips
on choosing a mounting location for the PC5132.
4. The LED on the motion detector does not turn on when I walk in
front of the unit.
The LED is for walk test purposes only. See your WLS904NB433 instruction
sheet for walk test instructions.
13
Programming Worksheets
[804] 5132--433 Wireless Expansion Programming
• 6-digit entry is required. See Section 3.1 “A note on Electronic Serial
Numbers” for details on programming 6-digit serial numbers.
Zone Serial Numbers
Default = 000000
[01] Zone 1
l_____l_____l_____l_____l_____l_____l
[17] Zone 17
l_____l_____l_____l_____l_____l_____l
[02] Zone 2
l_____l_____l_____l_____l_____l_____l
[18] Zone 18
l_____l_____l_____l_____l_____l_____l
[03] Zone 3
l_____l_____l_____l_____l_____l_____l
[19] Zone 19
l_____l_____l_____l_____l_____l_____l
[04] Zone 4
l_____l_____l_____l_____l_____l_____l
[20] Zone 20
l_____l_____l_____l_____l_____l_____l
[05] Zone 5
l_____l_____l_____l_____l_____l_____l
[21] Zone 21
l_____l_____l_____l_____l_____l_____l
[06] Zone 6
l_____l_____l_____l_____l_____l_____l
[22] Zone 22
l_____l_____l_____l_____l_____l_____l
[07] Zone 7
l_____l_____l_____l_____l_____l_____l
[23] Zone 23
l_____l_____l_____l_____l_____l_____l
[08] Zone 8
l_____l_____l_____l_____l_____l_____l
[24] Zone 24
l_____l_____l_____l_____l_____l_____l
[09] Zone 9
l_____l_____l_____l_____l_____l_____l
[25] Zone 25
l_____l_____l_____l_____l_____l_____l
[10] Zone 10
l_____l_____l_____l_____l_____l_____l
[26] Zone 26
l_____l_____l_____l_____l_____l_____l
[11] Zone 11
l_____l_____l_____l_____l_____l_____l
[27] Zone 27
l_____l_____l_____l_____l_____l_____l
[12] Zone 12
l_____l_____l_____l_____l_____l_____l
[28] Zone 28
l_____l_____l_____l_____l_____l_____l
[13] Zone 13
l_____l_____l_____l_____l_____l_____l
[29] Zone 29
l_____l_____l_____l_____l_____l_____l
[14] Zone 14
l_____l_____l_____l_____l_____l_____l
[30] Zone 30
l_____l_____l_____l_____l_____l_____l
[15] Zone 15
l_____l_____l_____l_____l_____l_____l
[31] Zone 31
l_____l_____l_____l_____l_____l_____l
[16] Zone 16
l_____l_____l_____l_____l_____l_____l
[32] Zone 32
l_____l_____l_____l_____l_____l_____l
14
P
Wireless Key Serial Numbers
Default = 000000
[41] Key 01
l_____l_____l_____l_____l_____l_____l
[42] Key 02
l_____l_____l_____l_____l_____l_____l
[43] Key 03
l_____l_____l_____l_____l_____l_____l
[44] Key 04
l_____l_____l_____l_____l_____l_____l
[45] Key 05
l_____l_____l_____l_____l_____l_____l
[46] Key 05
l_____l_____l_____l_____l_____l_____l
[47] Key 07
l_____l_____l_____l_____l_____l_____l
[48] Key 08
l_____l_____l_____l_____l_____l_____l
[49] Key 09
l_____l_____l_____l_____l_____l_____l
[50] Key 10
l_____l_____l_____l_____l_____l_____l
[51] Key 11
l_____l_____l_____l_____l_____l_____l
[52] Key 12
l_____l_____l_____l_____l_____l_____l
[53] Key 13
l_____l_____l_____l_____l_____l_____l
[54] Key 14
l_____l_____l_____l_____l_____l_____l
[55] Key 15
l_____l_____l_____l_____l_____l_____l
[56] Key 16
l_____l_____l_____l_____l_____l_____l
Wireless Key Function Key Options
Entry
00
01-02
03
Key Description
Entry
Key Description
Null Key
16
[✱][0] Quick Exit
For Future Use
17
[✱][1] Reactivate Stay/Aways
Stay Arm
18
For Future Use
04
Away Arm
19
[✱][7][3] Command Output #3
05
[✱][9] No-Entry Arm
20
For Future Use
06
[✱][4] Chime ON/OFF
21
[✱][7][4] Command Output #4
07
[✱][6][——][4] System Test
22-26
For Future Use
For Future Use
27
Disarm (OFF)
13
[✱][7][1] Command Output #1
28
Fire Alarm
14
[✱][7][2] Command Output #2 /
Sensor Reset
29
Auxiliary Alarm
15
For Future Use
30
Panic Alarm
08-12
15
P
Partition 1 Wireless Key Options
Default = 00
[59] Function Key 1
Function Key 2
l____l____l
Function Key 3
l____l____l
l____l____l
Function Key 4
l____l____l
l____l____l
Function Key 3
l____l____l
l____l____l
Function Key 4
l____l____l
Partition 2 Wireless Key Options
[60] Function Key 1
Function Key 2
Supervision
[81] Wireless Supervisory Window
l____l____l
Default = 10
The window is programmed in 15 minute increments. The
default programming is 10 (x 15minutes), which is equal to
150minutes (2.5 hours). Valid entries are (04) - (96), equal to 1
- 24 hours.
[82] Zone Device Supervision Options (1-8)
Default = ON
Option ON
Option OFF
l________l
Option 1
Zone 01 Supervision enabled
Disabled
l________l
Option 2
Zone 02 Supervision enabled
Disabled
l________l
Option 3
Zone 03 Supervision enabled
Disabled
l________l
Option 4
Zone 04 Supervision enabled
Disabled
l________l
Option 5
Zone 05 Supervision enabled
Disabled
l________l
Option 6
Zone 06 Supervision enabled
Disabled
l________l
Option 7
Zone 07 Supervision enabled
Disabled
l________l
Option 8
Zone 08 Supervision enabled
Disabled
[83] Zone Device Supervision Options (9-16)
Default = ON
Option ON
Option OFF
l________l
Option 1
Zone 09 Supervision enabled
Disabled
l________l
Option 2
Zone 10 Supervision enabled
Disabled
l________l
Option 3
Zone 11 Supervision enabled
Disabled
l________l
Option 4
Zone 12 Supervision enabled
Disabled
l________l
Option 5
Zone 13 Supervision enabled
Disabled
l________l
Option 6
Zone 14 Supervision enabled
Disabled
l________l
Option 7
Zone 15 Supervision enabled
Disabled
l________l
Option 8
Zone 16 Supervision enabled
Disabled
16
P
[84] Zone Device Supervision Options (17-24)
Default = ON
Option ON
Option OFF
l________l
Option 1
Zone 17 Supervision enabled
Disabled
l________l
Option 2
Zone 18 Supervision enabled
Disabled
l________l
Option 3
Zone 19 Supervision enabled
Disabled
l________l
Option 4
Zone 20 Supervision enabled
Disabled
l________l
Option 5
Zone 21 Supervision enabled
Disabled
l________l
Option 6
Zone 22 Supervision enabled
Disabled
l________l
Option 7
Zone 23 Supervision enabled
Disabled
l________l
Option 8
Zone 24 Supervision enabled
Disabled
[85] Zone Device Supervision Options (25-32)
Default = ON
Option ON
Option OFF
l________l
Option 1
Zone 25 Supervision enabled
Disabled
l________l
Option 2
Zone 26 Supervision enabled
Disabled
l________l
Option 3
Zone 27 Supervision enabled
Disabled
l________l
Option 4
Zone 28 Supervision enabled
Disabled
l________l
Option 5
Zone 29 Supervision enabled
Disabled
l________l
Option 6
Zone 30 Supervision enabled
Disabled
l________l
Option 7
Zone 31 Supervision enabled
Disabled
l________l
Option 8
Zone 32 Supervision enabled
Disabled
[90] Other Options
Default = OFF
Option ON
Option OFF
l________l
Options 1-5
For future use
l________l
Option 6
Sensitive RF
jamming detection
l________l
Option 7
RF Jam Detect Disabled RF Jam Detect Enabled
l________l
Option 8
Global Placement Test Individual Placement Test
17
Normal RF
jamming detection
Index
add
device 4
wireless key 4
antenna 1
global placement
test 10
removing
device 9
module 7
RF jamming 8, 12
batteries
replacing 12
type 2
buttons
programming 5
individual placement
test 11
interference 3
jamming signal
detection 8, 12
connect
Keybus 3
receiver 3
Keybus
default
module 9
panel 9
delete device 9
devices 2
adding 4
removing 9
distance from control
panel 1
electronic serial
number 4
enroll
device 4
PC5132 7
wireless key 4
ESN 4
factory default 9
frequency 1
function keys 5
location
choosing 3
low battery
devices 12
testing
door/window
contact 10
global 10
individual 11
motion detector 10
PC5132 10
placement 10
trouble 12
troubleshooting 13
mount
devices 11
PC5132 11
number
electronic, serial
partition programming 7
wireless keys 5
placement
PC5132 3
test 10
power 3
problems 12
serial number 4
slot number
wireless key 5
supervision
DEOL 8
device 8
disable 7
module 7
window 8
wireless key
access codes 6
activating outputs 6
arming/disarming 6
enrolling 4
identifying 6
programming 4
zone
adding 4
attribute 7
numbers 4
programming 7
wireless 7
LIMITED WARRANTY
Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months
from the date of purchase, the product shall be
free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return
of the product to its factory, at no charge for labour
and materials. Any replacement and/or repaired
parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is
longer. The original owner must promptly notify
Digital Security Controls Ltd. in writing that there
is defect in material or workmanship, such written notice to be received in all events prior to expiration of the warranty period.
International Warranty
The warranty for international customers is the
same as for any customer within Canada and the
United States, with the exception that Digital Security Controls Ltd. shall not be responsible for
any customs fees, taxes, or VAT that may be due.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized distributors and dealers have
a warranty program. Anyone returning goods to
Digital Security Controls Ltd. must first obtain
an authorization number. Digital Security Controls Ltd. will not accept any shipment whatsoever for which prior authorization has not been
obtained.
Conditions to Void Warranty
This warranty applies only to defects in parts and
workmanship relating to normal use. It does not
cover:
• damage incurred in shipping or handling;
• damage caused by disaster such as fire, flood,
wind, earthquake or lightning;
• damage due to causes beyond the control of
Digital Security Controls Ltd. such as excessive
voltage, mechanical shock or water damage;
• damage caused by unauthorized attachment, alterations, modifications or foreign objects;
• damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.);
• defects caused by failure to provide a suitable
installation environment for the products;
• damage caused by use of the products for purposes other than those for which it was designed;
• damage from improper maintenance;
• damage arising out of any other abuse, mishandling or improper application of the products.
Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty af-
ter a reasonable number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach of warranty. Under
no circumstances shall Digital Security Controls
Ltd. be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages
include, but are not limited to, loss of profits,
loss of the product or any associated equipment,
cost of capital, cost of substitute or replacement
equipment, facilities or services, down time,
purchaser’s time, the claims of third parties, including customers, and injury to property.
Disclaimer of Warranties
This warranty contains the entire warranty
and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability
or fitness for a particular purpose) And of all
other obligations or liabilities on the part of
Digital Security Controls Ltd. Digital Security
Controls Ltd. neither assumes nor authorizes
any other person purporting to act on its behalf to modify or to change this warranty, nor
to assume for it any other warranty or liability concerning this product.
This disclaimer of warranties and limited warranty are governed by the laws of the province
of Ontario, Canada.
WARNING: Digital Security Controls Ltd. recommends that the entire system be completely
tested on a regular basis. However, despite frequent testing, and due to, but not limited to,
criminal tampering or electrical disruption, it is
possible for this product to fail to perform as
expected.
Out of Warranty Repairs
Digital Security Controls Ltd. will at its option
repair or replace out-of-warranty products
which are returned to its factory according to
the following conditions. Anyone returning
goods to Digital Security Controls Ltd. must
first obtain an authorization number. Digital
Security Controls Ltd. will not accept any shipment whatsoever for which prior authorization
has not been obtained.
Products which Digital Security Controls Ltd. determines to be repairable will be repaired and returned. A set fee which Digital Security Controls
Ltd. has predetermined and which may be revised
from time to time, will be charged for each unit
repaired.
Products which Digital Security Controls Ltd. determines not to be repairable will be replaced by
the nearest equivalent product available at that
time. The current market price of the replacement
product will be charged for each replacement
unit.
© 2000 Digital Security Controls Ltd., Toronto, Canada
Tech. Line: 1-800-387-3630 • www.dscgrp.com
Printed in Canada
29004754 R002

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 1910:00:20 11:03:21
Producer                        : Acrobat Distiller 3.0 for Windows
Title                           : pc5132-433 v3-12 in im eng 29004754 r002
Subject                         : pc5132-433 v3-12 in im eng 29004754 r002
Creator                         : Adobe PageMaker 6.5
Author                          : neumannl
Modify Date                     : 2000:02:01 10:37:00-05:00
Page Count                      : 24
Page Mode                       : UseOutlines

EXIF Metadata provided by EXIF.tools