Tyco Safety Canada 00NB907 Wireless Door/Window Contact User Manual wls907 inis eng 29001837 r3 kp

Digital Security Controls Ltd. Wireless Door/Window Contact wls907 inis eng 29001837 r3 kp

Installation instructions

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSRemove CoverTo remove the cover of the WLS907 universal transmitter, insert a smallscrewdriver in the slot on the end of the unit. Push the tab to release the cover.Install BatteriesUse care when installing the batteries. Follow the guidelines below:1. Observe the correct polarity (see Figure 1).2. Install the batteries positive (+) side first (see Figure 2).Use only Eveready Alkaline Energizer batteries. Only replace low batteries withfresh ones. Always replace all three batteries at the same time.Figure 1 Figure 2Find a Location for the TransmitterLocate where the transmitter is to be mounted. Performthe Module Placement Test to ensure that the selectedlocation is in range of the wireless receiver (seereceiver Installation Manual for instructions).Determine where the magnet will be placed. In order toactivate the reed switch, the magnet must line up with theend of the transmitter OR the dot on the magnet must lineup with the dot on the edge of the cover(see Figure 3).Remove Circuit BoardBefore mounting the unit, remove the circuit board. Pull the tab located next to thebattery compartment. Gently lift the circuit board out of the plastic (see Figure 1).NOTE: Do not touch the coils on the circuit board as this may damage the unit.Mount Transmitter and MagnetMount the backplate of the transmitter using the screwsprovided and replace the circuit board. The head of thescrew must be below the circuit board so that the sensor isnot shorted out. Use flat-headed screws only. Use wallanchors if necessary. Replace the cover carefully, so as notto damage the antenna.Mount the magnet no more than ¼” from the transmitter. Usethe spacers provided (see Figure 4). Once the unit and magnet are mounted, openand close the window/door to ensure that none of the parts interfere with thismovement. Only one magnet can be used per transmitter.Metal will block/reflect a wireless signal. DO NOT mount the WLS907, or anyother wireless component, on or near large metal objects (i.e. metal doors, metalwindow blinds). Instead, find a close location that provides ‘good’ test resultsand use the external contacts instead of the built-in reed switch. Try to avoidmounting the wireless receiver in a basement or near large metal surfaces (i.e.metal ductwork) as this can reduce the range.Using External ContactsThe external contact terminals can be used to connect external contacts or otherswitches/devices to the universal transmitter. Install the additional device as perthe manufacturer’s instruction. Connect the device to the contact terminals of theWLS907. The input is normally closed and is not supervised.The wires connecting the external device to the input terminals can be anylength provided that the resistance of the wire does not exceed 100WWWWW.Only one contact can be used. If an external contact is used, do not install themagnet.Tamper SwitchesThere are two tamper switches on the WLS907 board. Both removing the cover and/orremoving the WLS907 from its mounting location will cause a zone tamper. See yourpanel installation manual for more information on trouble conditions.Enrolling a WLS907On the back of the door contact housing, there will be two serial numbers, a fivedigit and six digit. Please refer to your receiver installation manual for informationon which serial number should be enrolled.FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority touse this equipment.This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with themanufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found tocomply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules, whichare designed to provide reasonable protection against such interference in any residential installation. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause interference to television orradio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:•Re-orient the receiving antenna•Relocate the alarm control with respect to the receiver•Move the alarm control away from the receiver•Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.If necessary, the user should consult the dealer or an experienced radio/television technician for additional sugges-tions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington,D.C. 20402, Stock # 004-000-00345-4.Limited WarrantyDigital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shallbe free of defects in material and workmanship under normal use and that in fulfillment of any breach of such warranty,Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of theequipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to damageincurred in shipping or handling, or damage due to causes beyond control of Digital Security Controls Ltd. such aslightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improperapplication of the equipment.The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties,whether express or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Thiswarranty contains the entire warranty. Digital Security Controls Ltd. neither assumes, nor authorizes any other personpurporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liabilityconcerning this product.In no event shall Digital Security Controls Ltd. be liable for any direct , indirect or consequential damages, loss ofanticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installationor operation or failure of this product.Warning: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis.However, despite frequent testing, and due to but not limited to, criminal tampering or electrical disruption, it ispossible for this product to fail to perform as expected.Figure 3• W A R N I N G •Please refer to the System Installation Manual for information onlimitations regarding product use and function and information on thelimitations as to liability of the manufacturer.Figure 4WLS907NB433Wireless Door/Window Contact© 2000 Digital Security Controls Ltd., Toronto, CanadaTech. Line: 1-800-387-3630 • www.dscgrp.comPrinted in Canada 29003039 R005

Navigation menu