Tyco Safety Canada 00NB925 User Manual wls907 inis eng 29001837 r3 kp

Digital Security Controls Ltd. wls907 inis eng 29001837 r3 kp

Users guide

WLS925-433Mini Door/Window ContactINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS© 2000 Digital Security Controls Ltd.Toronto, Canada1-800-387-3630 • www.dscgrp.comPrinted in Canada 29005100 R001Remove CoverAt the notched location on the cover, insert the flat blade of a small screwdriverbetween between between between between the base and the cover and twist the screwdriver to pop the cover off.Install BatteryUse care when installing the battery and observe the correct polarity (seediagram below). Use only Eveready Lithium Energizer No. EL123AP battery.NOTE: Battery replacement must only be done by a qualified technician.Locate TransmitterLocate where the transmitter is to be mounted. Perform theModule Placement Test Module Placement Test Module Placement Test Module Placement Test Module Placement Test to ensure that the selected locationis in range of the wireless receiver (see receiver InstallationManual for instruction).Determine where the magnet will be placed. In order toactivate the reed switch, the magnet must line up with theend of the transmitter.Remove Circuit BoardBefore mounting the unit, remove the circuit board. At thenotched location on the base which is on the same side as the reed switch, insertthe blade of a small screwdriver between the base wall and the bottom of thecircuit board and pry the circuit board up.NOTE: Do not touch the coils on the circuit board as this may damage the unit.Mount Transmitter and MagnetMount the backplate of the transmitter using the screws provided and replace thecircuit board. The head of the screw must be below the circuit board so that thesensor is not shorted out. Use flat-headed screws only.Mount the magnet no more than ¼” from the transmitter. Use the spacersprovided . Once the unit and magnet are mounted,open and close the window/door to ensure that noneof the parts interfere with this movement. Only onemagnet can be used per transmitter.Using External ContactsThe external contact terminals can be used toconnect external contacts or other switches/devicesto the universal transmitter. Install the additionaldevice as per the manufacturer’s instruction.Connect the device to the contact terminals of the WLS925-433.The input is normally closed and is not supervised.For UL installations, the wires connecting the external device to the inputterminals must not exceed 36" (90.5 cm) in length. The contact and transmittermust also be in the same room.For non-UL installations, the wires connecting the external device to the input terminalscan be any length provided that the resistance of the wire does not exceed 100ΩΩΩΩΩ.Only one contact can be used. If an external contact is used, do not install the magnet.Tamper SwitchThere is one tamper switch on the WLS925 board. Removing the cover will cause azone tamper.Enrolling a WLS925On the back of the door contact housing, there will be two serial numbers, a fivedigit and six digit. Please refer to your receiver installation manual for informationon which serial number should be enrolled.FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority touse this equipment.This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with themanufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found tocomply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules, whichare designed to provide reasonable protection against such interference in any residential installation. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause interference to television orradio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:•Re-orient the receiving antenna•Relocate the alarm control with respect to the receiver•Move the alarm control away from the receiver•Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.If necessary, the user should consult the dealer or an experienced radio/television technician for additionalsuggestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and ResolveRadio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office,Washington, D.C. 20402, Stock # 004-000-00345-4.Limited WarrantyDigital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shallbe free of defects in material and workmanship under normal use and that in fulfillment of any breach of such warranty,Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of theequipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to damageincurred in shipping or handling, or damage due to causes beyond control of Digital Security Controls Ltd. such aslightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improperapplication of the equipment.The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties,whether express or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Thiswarranty contains the entire warranty. Digital Security Controls Ltd. neither assumes, nor authorizes any other personpurporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liabilityconcerning this product.In no event shall Digital Security Controls Ltd. be liable for any direct , indirect or consequential damages, loss ofanticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installationor operation or failure of this product.WarningDigital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis. However, despitefrequent testing, and due to but not limited to, criminal tampering or electrical disruption, it is possible for this product to failto perform as expected.WARNING!WARNING!WARNING!WARNING!WARNING!: Battery mayexplode if mistreated. Donot recharge, disassembleor dispose of in fire.

Navigation menu