Tyco Safety Canada 00SS929 Wireless 929 Spread Spectrum Transmitter User Manual wls909 is eng 29002095 r002

Digital Security Controls Ltd. Wireless 929 Spread Spectrum Transmitter wls909 is eng 29002095 r002

Users guide

FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use thisequipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:■Re-orient the receiving antenna.■Increase the separation between the equipment and receiver.■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.■Consult the dealer or an experienced radio/television technician for help.The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/TelevisionInterference Problems”. This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock #004-000-00345-4.Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device maynot cause interference, and (2) this device must accept any interference, including interference that may cause undesired operationof the device.Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-210. son utilisation est autoriséeseulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à acceptertout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.WLS929Wireless KeyOPERATING INSTRUCTIONS© 2000 Digital Security Controls Ltd.Printed in Canada 29004986 R001The WLS929 wireless key allows you to armand disarm your alarm system, as well asperform other keypad functions, from a unitsmall enough to keep in your pocket.Together with your installer, you can decidewhich functions you wish to have accessiblefrom your portable key.To activate any one of the four selectedfunctions, press and hold the appropriatebutton for two seconds. Your installer willindicate each function by applying a circularlabel on the rear of the unit or by installing pre-printed buttons.Signals will not be received if the key is not within the rangeof the wireless receiver.The default functions are as follows:Stay ArmingPress this button to arm your system in the Stay mode. All perimeter zones will bearmed, such as all window and door contacts, but the interior zones will remaininactive, allowing you to stay on the premises without setting off an alarm.Away ArmingPress this button to arm your system in the Away mode. Both the interior andexterior zones will be armed, allowing you to exit the premises.DisarmPress this button to disarm your system. You do not have to enter your accesscode when you use the key to disarm the system.PanicPress this button to notify your central monitoring station of a situation requiring thepolice, such as a break-in.Other available functions (to be programmed by the installer):• Fire • Command Outputs 1, 3, 4• Auxiliary • Command Output 2• No-Entry Delay Arming • Quick Exit• Chime ON/OFF • Reactivate Stay/Aways• System TestPlease discuss these options with your installer in order to program the bestpossible combination to suit your needs.Testing the WLS929 KeyTo test the batteries on your key, press and hold one of the arm or disarm buttons for fiveseconds. If the batteries are low, the Trouble light on any of your system’s keypads will turn ON.If the Trouble light turns ON, the key’s batteries must be replaced.NOTE: Pressing another button after completing the test may clear the trouble condition.The key’s batteries must still be replaced.Do not use a Fire, Auxiliary or Panic key to test your WLS929 unit as pressing thesebuttons will always notify your monitoring station of a non-medical emergency.To replace the batteries, remove the screw on the back of the keyand carefully separate the two sides of the key’s plastic casing.Remove the old batteries from between the two metal clips. Insertthe new batteries according to the diagram at right and reattachthe two sides of the key’s plastic casing. The WLS929 requiresthree batteries of type LR44.NOTE: The polarity of the batteries must be observed.TM–+LIMITED WARRANTYDigital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shallbe free of defect in materials and workmanship under normal use and that in fulfilment of any breach of such warranty,Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipmentto its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred inshipping or handling, or damage due to causes beyond the control of Digital Security Controls Ltd. such as lightning,excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper applica-tion of the equipment.The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties,whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Thiswarranty contains the entire warranty. Digital Security Controls Ltd. neither assumes, nor authorizes any other personpurporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liabilityconcerning this product.In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss ofanticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installationor operation or failure of this product.WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regularbasis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption,it is possible for this product to fail to perform as expected.backfront
FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use thisequipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:■Re-orient the receiving antenna.■Increase the separation between the equipment and receiver.■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.■Consult the dealer or an experienced radio/television technician for help.The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/TelevisionInterference Problems”. This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock #004-000-00345-4.Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device maynot cause interference, and (2) this device must accept any interference, including interference that may cause undesired operationof the device.Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-210. son utilisation est autoriséeseulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à acceptertout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.WLS929Wireless KeyOPERATING INSTRUCTIONS© 2000 Digital Security Controls Ltd.Printed in Canada 29004986 R001The WLS929 wireless key allows you to armand disarm your alarm system, as well asperform other keypad functions, from a unitsmall enough to keep in your pocket.Together with your installer, you can decidewhich functions you wish to have accessiblefrom your portable key.To activate any one of the four selectedfunctions, press and hold the appropriatebutton for two seconds. Your installer willindicate each function by applying a circularlabel on the rear of the unit or by installing pre-printed buttons.Signals will not be received if the key is not within the rangeof the wireless receiver.The default functions are as follows:Stay ArmingPress this button to arm your system in the Stay mode. All perimeter zones will bearmed, such as all window and door contacts, but the interior zones will remaininactive, allowing you to stay on the premises without setting off an alarm.Away ArmingPress this button to arm your system in the Away mode. Both the interior andexterior zones will be armed, allowing you to exit the premises.DisarmPress this button to disarm your system. You do not have to enter your accesscode when you use the key to disarm the system.PanicPress this button to notify your central monitoring station of a situation requiring thepolice, such as a break-in.Other available functions (to be programmed by the installer):• Fire • Command Outputs 1, 3, 4• Auxiliary • Command Output 2• No-Entry Delay Arming • Quick Exit• Chime ON/OFF • Reactivate Stay/Aways• System TestPlease discuss these options with your installer in order to program the bestpossible combination to suit your needs.Testing the WLS929 KeyTo test the batteries on your key, press and hold one of the arm or disarm buttons for fiveseconds. If the batteries are low, the Trouble light on any of your system’s keypads will turn ON.If the Trouble light turns ON, the key’s batteries must be replaced.NOTE: Pressing another button after completing the test may clear the trouble condition.The key’s batteries must still be replaced.Do not use a Fire, Auxiliary or Panic key to test your WLS929 unit as pressing thesebuttons will always notify your monitoring station of a non-medical emergency.To replace the batteries, remove the screw on the back of the keyand carefully separate the two sides of the key’s plastic casing.Remove the old batteries from between the two metal clips. Insertthe new batteries according to the diagram at right and reattachthe two sides of the key’s plastic casing. The WLS929 requiresthree batteries of type LR44.NOTE: The polarity of the batteries must be observed.TM–+LIMITED WARRANTYDigital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shallbe free of defect in materials and workmanship under normal use and that in fulfilment of any breach of such warranty,Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipmentto its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred inshipping or handling, or damage due to causes beyond the control of Digital Security Controls Ltd. such as lightning,excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper applica-tion of the equipment.The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties,whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Thiswarranty contains the entire warranty. Digital Security Controls Ltd. neither assumes, nor authorizes any other personpurporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liabilityconcerning this product.In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss ofanticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installationor operation or failure of this product.WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regularbasis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption,it is possible for this product to fail to perform as expected.backfront

Navigation menu