Tyco Safety Canada 06RFK55XX4 ASK Receiver User Manual 29007367R001 PK55xx RFK55xx 5 0 INIS EN
Digital Security Controls Ltd. ASK Receiver 29007367R001 PK55xx RFK55xx 5 0 INIS EN
Contents
- 1. Users Manual
- 2. User Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 784883 |
| Application ID | fv0LiDBmmSAsZSvrFI6nKA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 100.48kB (1256043 bits) |
| Date Submitted | 2007-04-25 00:00:00 |
| Date Available | 2007-04-25 00:00:00 |
| Creation Date | 2007-01-22 10:40:03 |
| Producing Software | Acrobat Distiller 8.0.0 (Windows) |
| Document Lastmod | 2007-04-19 11:07:45 |
| Document Title | 29007367R001_PK55xx_RFK55xx_5-0_INIS_EN.fm |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | tvecchiarelli |
PK55XX/RFK55XX-433 Installation Instructions, Instructions d’Installation, Installatiehandleiding, Asennusohjeet English, Français, Nederlands, Suomi PK5500 RFK5500 PK5501 RFK5501 PK5508 RFK5508 PK5516 RFK5516 WARNING: Please refer to the System Installation Manual for information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. NOTE: These instructions shall be used in conjunction with the system Installation Manual of the Control Panel with which this equipment is intended to be used. ATTENTION: Ce manuel contient des informations sur les restrictions concernant le fonctionnement et l’utilisation du produit et des informations sur les restrictions en ce qui concerne la responsabilité du fabricant. La totalité du manuel doit être lu attentivement. NOTE: Ce manuel doit être utilisé en conjonction avec le Manuel d'installation du Panneau de contrôle. WAARSCHUWING: Raadpleeg de installatiehandleiding van het systeem voor informatie over beperkingen m.b.t. productgebruik en functie en informatie over de beperkingen m.b.t. aansprakelijkheid van de fabrikant. OPMERKING: Deze instructies dienen te worden gebruikt in combinatie met de installatiehandleiding van het systeem van de centrale waarmee deze apparatuur gebruikt wordt. ADVARSEL: Vennligst se manualen for installasjon av systemet for informasjon om begrensningene angående bruk og funksjon av produktet og informasjon om begrensningene hva angår produsentens ansvar. LEGG MERKE TIL: Disse instruksene skal brukes sammen med manualen til kontrollpanelet for installasjon av systemet som dette utstyret er ment å brukes med. Disasembling (Free-standing) English 2. 1. Hooks Installation Instructions The PK55XX\RFK55XX keypads can be used on security systems with up to 64 zones. These keypads are compatible with the following DSC security systems: •PC580 •PC585 •PC1555MX •PC1565 •PC1616 •PC1832 •PC1864 •PC5005 •PC5008 •PC5010 •PC5015 •PC5016 •PC5020 The RFK55XX keypads combine a wireless receiver with the respective PK55XX keypad. Specifications • Temperature range: -10°C to +55°C (14°F to 131°F), Temperature range for UL/ULC: 0°C to +49°C (32°F to 120°F) • Humidity (MAX): 93%R.H. • Plastic enclosure protection degree: IP30, IK04 • Voltage rating: 12VDC nominal • Connects to control panel via 4-wire Keybus • 1 keypad zone input/PGM output* • PK55XX Current draw: 50mA (standby)/125mA (maximum) • RFK55XX Current draw: 75mA (standby)/135mA (maximum) • Wall mount tamper • 5 programmable function keys • Ready (Green LED), Armed (Red LED), Trouble (Yellow LED), AC (Green LED) • Low temperature sensor • Frequency: 433.92MHz (RFK55XX-433 Only) • Up to 32 wireless zones (RFK55XX Only) NOTE: * Zone not to be programmed as Fire type or 24h type. 2. Rotate 90° 3. Repeat steps 1. and 2. for left side Mounting You should mount the keypad where it is accessible to designated points of entry and exit. Once you have selected a dry and secure location, perform the following steps to mount the keypad. Disassemble Keypad 1. Removing the keypad from the backplate for the first time. (a) Position the keypad as indicated, insert screwdriver and rotate. 3. 4. Tamper 1. Insert the screwdriver into slot at an angle and push 2. Removing the keypad from backplate once mounted. (a) Open door, holding it 90° to the keypad, as shown below. (b) Insert screwdriver into slot located under the door hinge and rotate the screwdriver. Disasembling (Wall-Mounted) 3. Repeat steps 1. and 2. for right side 1. Insert the screwdriver into slot at an angle and push Wiring Knock Out Wiring Slot Knock Out Knock Out Tamper Hooks Press to snap 1. Secure Keypad to wall using mounting holes. Use all 4 screws provided unless mounting on a single gang box. 2. Place keypad into hooks on the backplate and swing down to engage. 3. Run wire through wiring slot or knockouts. Connect Keybus and PGM/Zone wiring to keypad. Place tamper switch into tamper hole on backplate. 4. Remove keypad from hooks. Place keypad into backplate, ensure the wire is pushed back into the wall as much as possible. Route the wire inside the keypad ensuring high components are avoided. Snap the front assembly closed, ensuring that there is no pressure to the keypad from the wire below. NOTE: If any tension found between the front keypad assembly and wiring, please open the keypad reroute the wire and close again. Repeat these steps until the keypad is closed properly. 2. Rotate 90° Mount and Wire Keypad Unpacking The Power keypad package includes the following parts: •One Power keypad •Keypad inner door labels •Four mounting screws •1 tamper switch •2 end-of-line resistors •Installation Instructions Swing to engage 1. Before wiring the unit, ensure that all power (AC transformer and battery) is disconnected from the control panel. 2. Connect the four Keybus wires from the PK55XX\RFK55XX control panel (red, black, yellow and RED green) to the keypad terminals. Refer to BLK diagram: YEL 3. If programmed as an input, you can GRN connect a device - such as a door contact To zone or P/Z - to the ‘P/Z’ terminal of the keypad. PGM output This eliminates the need to run wires back to the control panel for the device. To connect the zone, run one wire from the device to the ‘P/Z’ terminal and the other wire from the device to the B (black) terminal. For powered devices, run the red wire to the R (positive) terminal and the black wire to the B (negative) terminal. When using end of line supervision, connect the zone according to one of the configurations outlined in your system’s Installation Manual. 4. If the ‘P/Z’ terminal is programmed as an output, the output follows the PGM programmed in Section [080]. A small relay, buzzer or other DC operated device may be connected between the positive supply voltage and the ‘P/Z’ terminal (maximum load is 50mA). Applying Power Once all wiring is complete, and the equipment is secured to the building structure with at least two screws apply power to the control panel: 1. Connect the battery leads to the battery. 2. Connect the AC transformer. For more information on control panel power specifications, see the control panel Installation Manual. Programming the Keypad There are several program1 ming options available for the keypad. These are described below. Programming the keypad is similar to programming Toggle Option the rest of the system. When 1_ _ 4 _ _ _ _ you are in the keypad programming sections, the keypad will display which options are turned on along the top of the display. To turn an option on or off, press the number corresponding to the option on the number pad. The numbers of the options that are currently turned ON will be displayed. For example, if options 1 and 4 are on, the display will look like this on the different keypad displays: For information on programming the rest of your security system, please refer to your system’s Installation Manual. Broadcasting LCD Labels All LCD programming is done per keypad. If more than one LCD keypad is present on the system, labels programmed at one keypad can be broadcast to all other LCD keypads. Perform the following procedure in order to broadcast labels: Step 1 - Program one LCD keypad completely. Step 2 - Make sure all LCD keypads are connected to the Keybus. Step 3 - Enter keypad programming by pressing [,][8][Installer Code][,], then enter section [998] at the keypad that was programmed. The keypad will now broadcast all the information programmed to all the other LCD keypads on the system. Step 4 - When the keypad is finished press the [#] key to exit. NOTE: Label broadcast from this keypad is only compatible with other PK5500 and RFK5500 Keypads. Language Programming (PK5500\RFK5500 Only) Hold (<>) keys for 2 seconds to enter language programming, scroll to the desired language and Press [,] to select. NOTE: If section [077] option 4 is OFF, language programming can only be performed while in installers programming. Enrolling the Keypad The keypad will need to be assigned to a partition and slot if supervision or keypad zones are being used. Keypad assignments and keypad option programming must be done at each keypad individually. The 1st digit of keypad assignment is used to determine partition assignment (1 to 8). If partitioning is not used, enter [1]. For Global Keypads, enter [0]. 3. Press the number keys [1] to [9] corresponding to the letter you require. The first time you press the number the first letter will appear. Pressing the number key again will display the next letter. [1] - A, B, C, 1 [4] - J, K, L, 4 [7] - S, T, U, 7 [0] - Space [2] - D, E, F, 2 [5] - M, N, O, 5 [8] - V, W, X, 8 [3] - G, H, I, 3 [6] - P, Q, R, 6 [9] - Y, Z, 9,0 4. When the required letter or number is displayed use the arrow keys (<>) to scroll to the next letter. 5. When you are finished programming the Zone Label, press the [,] key, scroll to “Save,” then press [,]. 6. Continue from Step 2 until all Labels are programmed. NOTE: Label Programming can also be accessed from the [,][6] User Functions Menu ASCII Characters NOTE: LED and ICON keypads cannot be programmed as Global Keypads The 2nd digit of keypad assignment is used to determine slot assignment for keypad supervision. Each keypad will be assigned a different slot number from 1 to 8. PK5500 and RFK5500 LCD keypads come defaulted in slot 8. If LCD keypads are used one LCD keypad must remain in slot 8. NOTE: The RFK55XX enrolls as two modules: Light 1 = keypad section of the RFK55XX Light 17 = receiver section of the RFK55XX NOTE: Deleting all wireless devices from the RFK55XX or defaulting the RFK55XX will cause a supervisory fault. Enter the following at each keypad installed on the system: 1. Enter Installer Programming by pressing [,][8][Installer’s Code] 2. Press [000] for Keypad Programming 3. Press [0] for Partition and Slot Assignment 4. Enter the 1st digit (0 to 8 for partition assignment) 5. Enter the 2nd digit (1 to 8 for slot assignment supervision) 6. Press the [#] key twice to exit programming. 7. After assigning all keypads, perform a supervisory reset by entering [,][8][Installer’s Code][902] and wait for 60 seconds. 8. Press the [#] key to exit programming after 60 seconds. Programming Labels (PK5500\RFK5500 Only) 1. Enter keypad programming by pressing [,][8][Installer Code][,]. Enter the 3-digit section number for the label to be programmed. 2. Use the arrow keys (<>) to move the underline bar underneath the letter to be changed. Changing Brightness/Contrast LCD Keypads 1. 2. 3. 4. Press [,][6][Master code]. Use the [<][>] keys to scroll to either Brightness Control or Contrast Control. Press [,] to select the setting you want to adjust. a) ‘Brightness Control’: There are multiple backlighting levels. Use the [<][>] keys to scroll to the desired level. 5. b) ‘Contrast Control’: There are 10 different display contrast levels. Use the [<][>] keys to scroll to the desired contrast level. 6. To exit, press [#]. LED/ICON Keypads 1. Press [,][6][Master Code]. 2. Use the [>] key to move through the 4 different backlighting levels. 3. The level is automatically saved when you press [#] to exit. Changing the Buzzer Level LCD Keypads 1. 2. 3. 4. Press [,][6][Master Code]. Use the [<][>] keys to scroll to Buzzer Control. There are 21 different levels, use the [<][>] keys to scroll to the desired level. To exit, press [#]. LED/ICON Keypads 1. Press [,][6][Master Code]. 2. Use the [<] key to move through the 21 different buzzer levels. 3. The level is automatically saved when you press [#] to exit. Keypad Enrollment [065] Fire Alarm Label (28 Characters) (PK5500\RFK5500 Only) Enter keypad programming by pressing [,][8][Installer’s Code][000]. [0] Partition / Slot Assignment Digit 1st 2nd Option Valid Range Default Partition Assignment (0=Global Keypad) 0 to 8 I_____I Slot Assignment 1 to 8 LED,ICON=1/LCD=8 I_____I [1]-[5] Function Key Assignment Function Key Button Valid Range Default Function [1] Function Key 1 Assignment 00 to 32 03 Stay Arm I_____I_____I [2] Function Key 2 Assignment 00 to 32 04 Away Arm I_____I_____I [3] Function Key 3 Assignment 00 to 32 06 Chime On/Off I_____I_____I [4] Function Key 4 Assignment 00 to 32 14 [5] Function Key 5 Assignment 00 to 32 16 Command Output 2 I_____I_____I Quick Exit I_____I_____I Keypad Function Keys Please see your system installation manual for a complete list of all the function key options available for your system. [00] - Null [08] - Bypass Mode [17] - Activate Stay/Away [28] - Partition 4 Select [01] - Partition 1 Select [09] - Trouble Display [19] - Command Output 3 [29] - Partition 5 Select [02] - Partition 2 Select [10] - Alarm Memory [21] - Command Output 4 [30] - Partition 6 Select [03] - Stay Arm [11] - User Programming [22] - Activate Camera [31] - Partition 7 Select [04] - Away Arm [12] - User Functions [23] - Bypass Recall [32] - Partition 8 Select [05] - No Entry Arm [13] - Command Output 1 [24] - Bypass Group Recall [06] - Chime On/Off [14] - Command Output 2 [26] - Time & Date Program [07] - System Test [16] - Quick Exit [27] - Partition 3 Select Default:“Fire Zone” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [065] I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [066] Fail to Arm Event Message (PK5500\RFK5500 Only) Default: “System Has Failed to Arm” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [066] I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [067] Alarm When Armed Event Message (PK5500\RFK5500 Only) Default: “Alarm Occurred While Armed < >” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [067] I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [071] First User Display Mask Default ON ON ON ON OFF OFF OFF OFF I____I I____I I____I I____I I____I I____I I____I I____I Option ON 1 Hold [P]anic Key prompt ON 2 Auto-arm Control/Time prompt ON 3 Quick Arm prompt ON 4 Interior Arm prompt ON 5 Quick Exit prompt ON 6 Thermostat Control prompt ON 7 ACK All Trouble Prompt ON 8 Music Input prompt ON OFF Hold [P]anic Key prompt OFF Auto-arm Control/Time prompt OFF Quick Arm prompt OFF Interior Arm prompt OFF Quick Exit prompt OFF Thermostat Control prompt OFF ACK All Trouble Prompt OFF Music Input prompt OFF [072] Second User Display Mask Default ON OFF OFF ON ON OFF OFF OFF Option ON OFF 1 User-initiated Call-up prompt ON User-initiated Call-up prompt OFF 2 For Future Use 3 Walk Test prompt ON Walk Test prompt OFF 4 Command Output#1 prompt ON Command Output#1 prompt OFF Keypad Programming 5 Command Output#2 prompt ON Command Output#2 prompt OFF Enter keypad programming by pressing [,][8][Installer Code][,] [001]-[064] Zone Label 1 to 64 (PK5500\RFK5500 Only) 6 Command Output#3 prompt ON Command Output#3 prompt OFF ex. For Zone 1 enter section [001], for Zone 2 enter section [002] etc. Default: “Zone 1” - “Zone 64” 7 Command Output#4 prompt ON Command Output#4 prompt OFF 8 For Future Use Section Zone Label [073] Download LCD Message Duration (PK5500\RFK5500 Only) I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I Default: 003 I_____I_____I_____I (Valid entries are 000-255), 000=Unlimited Message Disp. [001] to [064] 1 to 64 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I This number represents the number of times the Downloaded message is cleared by pressing any key while the message is up after timeout). I____I I____I I____I I____I I____I I____I I____I I____I [074] Key Options Default ON ON ON OFF I____I I____I I____I I____I Option ON 1 [F]ire Key Enabled 2 [A]uxiliary Key Enabled 3 [P]anic Key Enabled 4-8 For Future Use OFF [F]ire Key Disabled [A]uxiliary Key Disabled [P]anic Key Disabled I____I I____I I____I I____I I____I I____I I____I I____I Option ON 1 Display Code when Programming 2 Local Clock Display ON 3 Local Clock Displays 24-hr Time 4 Auto Alarm Memory Scroll Enabled 5 Local Display of Temperature ON 6 Bypass Options prompt ON 7 For Future Use 8 Auto-Scroll Open Zones ON OFF Display “Xs” when Programming Local Clock Display OFF Local Clock Displays AM/PM Auto Alarm Memory Scroll Disabled Local Display of Temperature OFF Bypass Options prompt OFF Auto-Scroll Open Zones OFF [077] Second Keypad Options Default ON ON OFF ON OFF ON ON OFF I____I I____I I____I I____I I____I I____I I____I I____I Option ON 1 Chime Enabled for Zone Openings 2 Chime Enabled for Zone Closings 3 5th Terminal is Keypad PGM Output 4 Language Selection from Any Menu 5 Power LED Enabled 6 Power LED indicates AC present 7 Alarms always Displayed When Armed 8 Low Temperature Warning Enabled For Partition 1 Command O/P 1 to 4 enter [120] to [123] For Partition 2 Command O/P 1 to 4 enter [124] to [127] For Partition 3 Command O/P 1 to 4 enter [128] to [131] For Partition 4 Command O/P 1 to 4 enter [132] to [135] For Partition 5 Command O/P 1 to 4 enter [136] to [139] For Partition 6 Command O/P 1 to 4 enter [140] to [143] For Partition 7 Command O/P 1 to 4 enter [144] to [147] For Partition 8 Command O/P 1 to 4 enter [148] to [151] Cmd. Section Part Output [076] First Keypad Options Default ON ON OFF ON OFF ON OFF OFF [120]-[151] Command Output Labels (PK5500\RFK5500 Only) Default: “Command_O/P_1” - “Command_O/P_4” OFF Chime Disabled for Zone Openings Chime Disabled for Zone Closings 5th Terminal is Keypad Zone Input Language Selection From Installer's Power LED Disabled Power LED indicates AC absent Alarms not Displayed When Armed Low Temperature Warning Disabled [120]-[151]1to8 1to4 Label I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [201]-[264] Door Chime Sound Programming You can program the keypad to make up to four different door chime sounds for individual zones. ex. For Zone 1 enter section [201], for Zone 2 enter section [202] etc. Default Option ON OFF ON I____I 1 6 Beeps Disabled OFF I____I 2 “Bing-Bing” Sound Disabled OFF I____I 3 “Ding-Dong” Sound Disabled OFF I____I 4 Alarm Tone Disabled OFF I____I 5-8 For Future Use [995][,] Reset Keypad Options to Factory Default [996][,] Label Default (PK5500\RFK5500 Only) [997] View Software Version (PK5500\RFK5500 Only) [998][,] Initiate Global Label Broadcast (PK5500\RFK5500 Only) [999][,] Reset Keypad EEPROM to Factory Defaults Keypad Display Symbols – Indicates that there are zones automatically or 8 Bypass manually bypassed. 9 For Future Use 10 Arm Mode – Indicates the mode the panel is armed in. Stay – Indicates that the panel is armed in the Stay 12 11 10 8 7 [080] PGM Terminal 1 Mode. It will turn on at the beginning of the Exit Default: 01 I_______I_______I PGM Output Number 1 Fire – Indicates that there are fire alarms in memory. Delay [101]-[108] Partition Labels (PK5500\RFK5500 Only) 2 Memory – Indicates that there are alarms in memory. Away – Indicates that the panel is armed in the Away Mode. It will turn on at the beginning of the Exit Light (green) – If the Ready light is on, the system ex. For Partition 1 enter section [101], for Partition 2 enter section [102] etc. 3 Ready Delay is ready for arming. Light (red) – If the Armed light is on, the system 11 Chime – This icon turns on when Door Chime is enabled on Section Partition Label 4 Armed has been armed successfully. the system and will turn off when Door Chime is disabled. I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I 5 System Trouble – Indicates that a system trouble is active. Open – When zones are opened, this icon will turn on, and [101] to [108] 1 to 8 6 AC – Indicates that AC is present at the main panel. 12 7 segment displays 1 and 2 will scroll through the open I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I – Indicates that the system is in Installer’s Prozones. 7 Program NOTE: Partition 1 Label is also used as the System Label gramming, or the keypad is busy. Wireless Integration (RFK55XX Only) Compatible Wireless Devices (RFK55XX-433 Only) The RFK55XX can receive signals from the following devices: •WLS914-433 Pet Immune PIR •WS4965 Tri-Zone Contact •WS4938 Panic Button •WS4916 Smoke Detector •WLS912L-433 Glass Break Detector •WLS904(P)L-433 Pet Immune PIR •WLS925L-433 Mini Door/Window Contact •WS49X9 Wireless Keys Downloading The RFK55XX product has an integrated wireless receiver. When downloading to this keypad, please select the PC5132-433 v5.1 file. DLS2002 and greater must be used in order to have the capability of downloading to this keypad. Testing Wireless Devices 1. Temporarily put the wireless devices in the places you want to mount them. 2. At a system keypad, enter [,][8][Installer Code]. 3. Enter programming section [904], then enter the two digit zone number. NOTE: If global placement test is enabled (Section [90], option 8 ON) enter [01] to test all zones. 4. Activate the device being tested until a result is displayed on the keypad or sounded by the keypad or bell Result LED/ICON Keypad LCD Keypad Bell/Buzzer Good Light 1 ON Steady Good 1 Beep/Squawk Bad Light 3 ON Steady Bad 3 Beeps/Squawks Activate the device until you get 3 good results in a row. Wait 10 seconds between each test on the same device. You may mount wireless devices where results were good. Devices indicating a bad result must be moved to another location. You may only have to move the device a few inches to correct a bad result. NOTE: Do not mount any device where a “bad” test result was indicated. Testing Portable Device Reception To test portable devices (e.g., WS4938, WS4939) press the button(s) at several different points in the installation, to confirm the coverage area. If these devices do not operate from all points in the installation, you will need to move the RFK55XX. Replacing Wireless Device Batteries 1. Remove the cover of the device from its backplate. This creates a tamper condition on the zone. 2. Refer to the battery installation instructions on the Installation Sheet of each component. Be sure to note the proper orientation of the batteries as you install them. 3. When the fresh batteries are in place, re-attach the cover to the backplate. The tamper is restored and the zone sends a battery trouble restoral signal to the receiver. The battery trouble is now clear and the device should function normally. NOTE: When batteries in one device need to be replaced, the batteries in all devices should be replaced at the same time. Troubleshooting 1. When I enter the 2-digit zone number when adding a wireless device, the keypad gives me a long beep. • You cannot enter ESNs unless the RFK55XX is properly connected to the Keybus. 2. I have entered the ESN for the device but when I violate the device, the zone does not show open on the keypad. Check the following: • Ensure the ESN has been entered correctly • Ensure that the zone is enabled for the partition (if partition programming is used). • Ensure that the wireless zone is not assigned to a zone used by PC5108 modules, an on-board zone or a keypad zone. • Ensure that the zone is programmed for something other than “Null Operation” and that the wireless zone attribute is turned on. 3. When I try a module placement test I get no result or “Bad” results. Check the following: • Verify that you are testing the correct zone • Verify that the correct ESN was entered when the device was enrolled • Verify that the device is in range of the RFK55XX. Try testing the device in the same room as the receiver. • Confirm that the RFK55XX is properly connected to the Keybus. • Check that you are testing the zone correctly. Refer to the instructions that came with the zone. • Check that the batteries are working and installed correctly. • Look for large metal objects that may be preventing the signal from reaching the RFK55XX. • The device must be located where consistent “Good” results are obtained. If several devices show “Bad” results, or if panic pendants and wireless keys operate inconsistently, move the receiver. 4. The LED on the motion detector does not turn on when I walk in front of the unit. • The LED on the motion detector is for walk test purposes only. See your WLS904-433/WLS904P(L)-433 Instruction Sheet for walk test instructions. Notes: Wireless Programming (RFK55XX Only) Enter Wireless programming by pressing [,][8][Installer’s Code][804] [01]-[32] Wireless Device Serial Number Zone Serial Numbers Default = 000000 [01] Zone 1 I_____I_____I_____I_____I_____I_____I [17] Zone 17 I_____I_____I_____I_____I_____I_____I [02] Zone 2 I_____I_____I_____I_____I_____I_____I [18] Zone 18 I_____I_____I_____I_____I_____I_____I [03] Zone 3 I_____I_____I_____I_____I_____I_____I [19] Zone 19 I_____I_____I_____I_____I_____I_____I [04] Zone 4 I_____I_____I_____I_____I_____I_____I [20] Zone 20 I_____I_____I_____I_____I_____I_____I [05] Zone 5 I_____I_____I_____I_____I_____I_____I [21] Zone 21 I_____I_____I_____I_____I_____I_____I [06] Zone 6 I_____I_____I_____I_____I_____I_____I [22] Zone 22 I_____I_____I_____I_____I_____I_____I [07] Zone 7 I_____I_____I_____I_____I_____I_____I [23] Zone 23 I_____I_____I_____I_____I_____I_____I [08] Zone 8 I_____I_____I_____I_____I_____I_____I [24] Zone 24 I_____I_____I_____I_____I_____I_____I [09] Zone 9 I_____I_____I_____I_____I_____I_____I [25] Zone 25 I_____I_____I_____I_____I_____I_____I [10] Zone 10 I_____I_____I_____I_____I_____I_____I [26] Zone 26 I_____I_____I_____I_____I_____I_____I [11] Zone 11 I_____I_____I_____I_____I_____I_____I [27] Zone 27 I_____I_____I_____I_____I_____I_____I [12] Zone 12 I_____I_____I_____I_____I_____I_____I [28] Zone 28 I_____I_____I_____I_____I_____I_____I [13] Zone 13 I_____I_____I_____I_____I_____I_____I [29] Zone 29 I_____I_____I_____I_____I_____I_____I [14] Zone 14 I_____I_____I_____I_____I_____I_____I [30] Zone 30 I_____I_____I_____I_____I_____I_____I [15] Zone 15 I_____I_____I_____I_____I_____I_____I [31] Zone 31 I_____I_____I_____I_____I_____I_____I [16] Zone 16 I_____I_____I_____I_____I_____I_____I [32] Zone 32 I_____I_____I_____I_____I_____I_____I [41]-[56] Wireless Key Serial Number Wireless Key Serial Numbers Default = 000000 [41] Key 1 I_____I_____I_____I_____I_____I_____I [49] Key 9 I_____I_____I_____I_____I_____I_____I [42] Key 2 I_____I_____I_____I_____I_____I_____I [50] Key 10 I_____I_____I_____I_____I_____I_____I [43] Key 3 I_____I_____I_____I_____I_____I_____I [51] Key 11 I_____I_____I_____I_____I_____I_____I [44] Key 4 I_____I_____I_____I_____I_____I_____I [52] Key 12 I_____I_____I_____I_____I_____I_____I [45] Key 5 I_____I_____I_____I_____I_____I_____I [53] Key 13 I_____I_____I_____I_____I_____I_____I [46] Key 6 I_____I_____I_____I_____I_____I_____I [54] Key 14 I_____I_____I_____I_____I_____I_____I [47] Key 7 I_____I_____I_____I_____I_____I_____I [55] Key 15 I_____I_____I_____I_____I_____I_____I [48] Key 8 I_____I_____I_____I_____I_____I_____I [56] Key 16 I_____I_____I_____I_____I_____I_____I [61]-[68] Wireless Function Key Options Function Key [61] Partition 1 [62] Partition 2 [63] Partition 3 [64] Partition 4 [65] Partition 5 [66] Partition 6 [67] Partition 7 [68] Partition 8 Key 1 Default I_____I_____I 03 I_____I_____I 03 I_____I_____I 03 I_____I_____I 03 I_____I_____I 03 I_____I_____I 03 I_____I_____I 03 I_____I_____I 03 Key 2 Default I_____I_____I 04 I_____I_____I 04 I_____I_____I 04 I_____I_____I 04 I_____I_____I 04 I_____I_____I 04 I_____I_____I 04 I_____I_____I 04 Key 3 Default I_____I_____I 27 I_____I_____I 27 I_____I_____I 27 I_____I_____I 27 I_____I_____I 27 I_____I_____I 27 I_____I_____I 27 I_____I_____I 27 Key 4 Default I_____I_____I 30 I_____I_____I 30 I_____I_____I 30 I_____I_____I 30 I_____I_____I 30 I_____I_____I 30 I_____I_____I 30 I_____I_____I 30 Keypad Function Keys Please see your system installation manual for a complete list of all the function key options available for your system. [00] - Null [03] - Stay Arm [04] - Away Arm [05] - No Entry Arm [06] - Chime On/Off [16] - Quick Exit [07] - System Test [17] - Activate Stay/Away [13] - Command Output 1 [19] - Command Output 3 [14] - Command Output 2 [21] - Command Output 4 [69] Wireless Keys (1-16) Partition Assignments Default = 01 Key 1 I_____I_____I Key 5 I_____I_____I Key 9 I_____I_____I Key 2 I_____I_____I Key 6 I_____I_____I Key 10 I_____I_____I Key 3 I_____I_____I Key 7 I_____I_____I Key 11 I_____I_____I Key 4 I_____I_____I Key 8 I_____I_____I Key 12 I_____I_____I [27] - Disarm [28] - Fire Alarm [29] - Auxiliary Alarm [30] - Panic Alarm Key 13 Key 14 Key 15 Key 16 I_____I_____I I_____I_____I I_____I_____I I_____I_____I [81] Wireless supervisory Window Default: [NA] 96 = 24 hours / [EU] 10 =2.5 hours I_____I_____I The window is programmed in 15 minute increments. Valid entries are 10 to 96, equal to 2.5 to 24 hours. [82]-[85] Zone Device Supervision Options Default ON [82] Zone Option 1 Option 2 Option 3 Option 4 Option 5 Option 6 Option 7 Option 8 Supervision [83] ON/OFF Zone I_____I I_____I 10 I_____I 11 I_____I 12 I_____I 13 I_____I 14 I_____I 15 I_____I 16 Supervision [84] ON/OFF Zone I_____I 17 I_____I 18 I_____I 19 I_____I 20 I_____I 21 I_____I 22 I_____I 23 I_____I 24 Supervision [85] ON/OFF Zone I_____I 25 I_____I 26 I_____I 27 I_____I 28 I_____I 29 I_____I 30 I_____I 31 I_____I 32 Supervision ON/OFF I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I [90] Other Options NA Default EU Default Option ON OFF OFF OFF I____I 1-4 For Future Use ON OFF I____I 5 RF Delinquency Disabled RF Delinquency Enabled OFF OFF I____I 6 For Future Use ON OFF I____I 7 RF Jam Detect Disabled RF Jam Detect Enabled OFF OFF I____I 8 Global Placement Test Individual Placment Test NOTE: For UL Listed installations, the RF Jam detect feature must be enabled. NOTE: For DD243 installations, the RF delinquency feature should be enabled. NOTE: Supervision must be enabled for RF Delinquency. [93] RF Jam Detect Zone Default: 00 I_____I_____I Valid entries = 01 - 32, 00 = No RF Jam tone selected. Select an unused zone that will be set to the tamper state when a jamming signal is detected. Limited Warranty Digital Security Controls warrants that for a period of 12 months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product. Warning: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected. Important Information:Changes or modifications not expressly approved by Digital Security Controls could void the user’s authority to operate this equipment. ©2007 Digital Security Controls, Toronto, Canada • www.dsc.com FCC Compliance Statement Caution: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Re-orient the receiving antenna • Relocate the alarm control with respect to the receiver • Move the alarm control away from the receiver • Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. IC:160A-RFK55XX4 The term IC before the radio certification number signifies that the Industry Canada technical specifications were met. EN5131-1 Grade2/Class II Operating Instructions shall be made available to the user.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2007:01:22 10:40:03-05:00 Modify Date : 2007:04:19 11:07:45-03:00 Producer : Acrobat Distiller 8.0.0 (Windows) Mod Date : 2007:04:19 11:07:45-03:00 Creation Date : 2007:01:22 10:40:03-05:00 Author : tvecchiarelli Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2007:04:19 11:07:45-03:00 Document ID : uuid:740c9530-df15-413b-9045-b0f5f1fbf19f Instance ID : uuid:e99b729f-dd56-44b1-950b-2729642765bc Format : application/pdf Title : 29007367R001_PK55xx_RFK55xx_5-0_INIS_EN.fm Creator : tvecchiarelli Page Count : 8 Has XFA : NoEXIF Metadata provided by EXIF.tools