Tyco Safety Canada 09WS4985 Wireless Flood Sensor User Manual

Digital Security Controls Ltd. Wireless Flood Sensor

User Manual

WS4985 One-Way Wireless Flood Detector(English) Installation InstructionsUse this installation sheet along with the associated DSC wireless receiver and control panel installation manuals. All instructions specified within those manuals must be observed.The WS4985 is a one-way wireless flood detector intended for use with compatible DSC Security Systems. Multiple WS4985 can be enrolled on and supervised by the same security panel up to the maximum supported by that panel.The flood detector consists of a flood sensor and a wireless transmitter that are connected by a 6ft (1.82m) wire cable, see below. This device continuously monitors for flood conditions. If flood conditions are detected, the WS4985 wirelessly communicates this alarm condition to the control panel receiver.Specifications:Operating Humidity: xx% RH (non-condensing) at xx°COperating Temperature: -10°C to 60°COperating Frequency: 433MHzWireless Range: xxx (show in translations only ) outdoor, line of sightBattery: CR2 Lithium (Panasonic/Duracell)Battery Life: xx years (under typical use)Compatible with receivers: RF5132-433/868, SCW9045/47-433/868, and RFK55XX-433/868 (keypads with receivers)Out of Box: WS4985, Hardware pack, Installation SheetACTIVATION, LOCATION and OPERATIONThe WS4985 comes with the battery pre-installed. To activate it, hold the WS4985 transmitter firmly in one hand and pull the plastic tab in the direction indicated. Then, select the locations where the transmitter and sensor will be mounted. For detailed operation of your alarm system, refer to the Alarm System user manual. ENROLLMENT, PROGRAMMING and PLACEMENTThe one-way wireless flood detector must be enrolled on the security panel before it can transmit system events, supervi-sory signals, or provide the local WS4985 status (e.g., case and wall tamper switch state, battery state, and line cut state).STEP 1 – ENROLLINGThe WS4985 can be automatically enrolled (Quick Enroll) or manually enrolled (Serial Number Programming). Perform one of the following:QUICK ENROLL - Steps 1-41. Enter [*8] [Installer Code] [898] on any system keypad.2. Place the Flood Detector near the Control panel.3. Tamper the WS4985 by closing the circuit between the probes of the flood sensor with a screwdriver.4. The Keypad will displays the ESN (electronic serial number). Press [*] to confirm it. Flood Detector # Serial Number[xxx] #1[xxx] #2[xxx] #3[xxx] #4
NOTE: The electronic serial number is a 6-digit alphanumeric number located on a sticker on the wireless device. 5. Repeat steps 2 to 4 to enroll additional WS4985.SERIAL NUMBER PROGRAMMING1. Enter [*][8] [Installer Code] on a system keypad to enter installer programming on any system keypad.2. Enter [804] to enter ESN (electronic serial number) programming.3. Scroll to the desired subsections [01]-[32] (e.g., [01] zone 1... [32] zone 32).4. Enter the 6-digit ESN located on the back of the unit in the next available zone slot. 5. Repeat steps 3 and 4 to enroll additional devices. 6. Press [#] to exit the current programming section. STEP 2 – PROGRAM ZONE DEFINITION1. Enter Section [001] - [004] zone definition.2. Define the corresponding zone with the appropriate zone type (e.g., delay (01), instant (03), ...).3. Press [#] to exit the current programming section.STEP 3 – ENABLE WIRELESS ZONE ATTRIBUTE1. Enter Section [101] - [132] wireless zone atttribute. 2. Toggle ON/OFF the desired option (e.g., 1, 2, ...)3. Press [#] to exit the current programming section. Note: Turn Option [8] ON (wireless zone attribute) in the corresponding zone attribute section for PowerSeries Sys-tems.STEP 4 – DEVICE PLACEMENT TESTTo ensure there is good signal strength from where they are positioned, all wireless devices must be tested.1. Enter [904] followed by the wireless zone to test (e.g., [01]-[32]).2. Tamper the WS4985 by closing the circuit between the probes of the flood sensor with a screwdriver.3. The control panel is programmed to respond with 1 beep if the location is “Good”, and 3 beeps if the location is “Bad”.DEVICE MOUNTINGThe installer is responsible for ensuring that the WS4985 is securely mounted in the intended location. If mounting the sensor portion onto the floor, locate it where the water will first run to and accumulate. The contacts should touch the floor completely.Note: DO NOT mount the transmitter portion of the device behind a metal object such a washing machine, refrigerator, or freezer.1. Sensor Portion: Secure the sensor to the mounting surface with all the screws provided. If surface conditions are unsuitable, the sensor can be attached with silicone.2. Transmitter Portion: Remove the backplate from the transmitter by inserting a flathead screwdriver into either side of the transmitter. Carefully twist to separate the top and bottom plastic. If using the provided screws, mount the back of the transmitter with them. Otherwise, apply the VHB tape supplied to the back of transmitter and apply it to the sur-face using firm pressure.Note: Test the unit at least once yearly. BATTERY REPLACEMENTTo replace the battery, insert a flathead screwdriver into either side of the transmitter end and carefully twist to separate the top and bottom plastic. Once separated, the battery will be visible. Remove the old battery and install the new battery in the polarity indicated by the engraving. If the batteries are installed incorrectly, in the reverse polarity, the flood detec-tor will not work. Under typical use the WS4985 is capable of operating on battery power alone without having to change the batteries for xx years. REPLACE ONLY WITH THE TYPE RECOMMENDED BY THE MANUFACTURER. Do not try to recharge these batteries. Disposal of used batteries must be made in accordance with the waste recovery and recycling regulations in your area.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is purchased under the following license terms:• This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the manufacturer of the integrated security systems and the developer of the software and any related products or components (“HARDWARE”) which You acquired. • If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials, and “online” or electronic documentation. • Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You under the terms of that license agreement. • By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.SOFTWARE PRODUCT LICENSEThe SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold. 1. GRANT OF LICENSE This EULA grants You the following rights:(a)Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed. (b)Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different computers, including a workstation, ter-minal or other digital electronic device (“Device”). In other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used.(c)Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFT-WA R E .2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS (a)Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and condi-tions of this EULA.(b)Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one HARDWARE unit.(c)Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated prod-uct. In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA..(d)Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.(e)Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of this EULA. In such event, You must destroy all cop-ies of the SOFTWARE PRODUCT and all of its component parts.(g)Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorporated into the SOFT-WARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompa-nying the SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers.4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export restrictions. 5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall be Toronto, Canada, and the language of the arbitration shall be English.7. LIMITED WARRANTY(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIRE-MENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREE-MENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFT-WARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCI-DENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICU-LAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PER-SON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PROD-UCT.(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPI-TAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected. ,FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IC: 160A-WS4985 The term ‘IC:’ before the radio certification number only signifies that Industry Canada technical specifications were met. This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Limited WarrantyDigital Security Controls warrants that for a period of 12 months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product. Warning: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tamper-ing or electrical disruption, it is possible for this product to fail to perform as expected.Important Information:Changes or modifications not expressly approved by Digital Security Controls could void the user’s authority to operate this equipment.29007537R001The complete R&TTE Declaration of Conformity can be found at http://www.dsc.com/listings_index.aspx. ©2008 Digital Security Controls, Toronto, Canada Technical Support: 1-800-387-3630 • www.dsc.comPrinted in Canada

Navigation menu