Tyco Safety Canada 09WT4911 Wireless Outdoor Siren User Manual

Digital Security Controls Ltd. Wireless Outdoor Siren

User Manual

Use this installation sheet along with the associated alarm system installation manual forinstallation instructions and programming details. All instructions specified within thatmanual must be observed.The WT4911 is a two-way wireless outdoor siren. Siren sounds and the strobe light areactivated when an alarm condition is received via DSC wireless protocol from a compatible,two-way enabled security panel (e.g., PC9155). The WT4911 must be enrolled on thesecurity panel before it can receive commands from the panel for sounding alarms, strobeactivation and communicating a required response, such as the WT4911 status or the localoutdoor temperature. The outdoor siren is capable of sounding different alarm cadences(e.g., carbon monoxide, continuous burglary, pulsating fire, or temporal three fire), bellsquawks, and buzzer tones to suit the type of command it receives. Up to four WT4911 canbe enrolled on the same security panel and supervised as separate units. To ensure two-way contact between the siren and the security panel, the WT4911 regularly sends supervi-sory signals to the security panel. With each supervisory signal sent to the panel, the sirenprovides the outdoor temperature. In addition, the WT4911 monitors for the case and walltamper switch states, and the battery state. In the event of a low battery or a tamper acti-vation, the WT4911 will transmit the appropriate signal to the security panel, and (if con-figured) provide an audible and visual indication that a local event has occurred.Specifications Two-Way Wireless Outdoor Siren EnrollmentSetting up the WT4911 consists of enrolling and powering up the device. Enrolling theWT4911 permits the siren to communicate with the security panel. The installer can acti-vate the outdoor siren by Quick Enrollment or Serial Number Programming, see below.Quick EnrollmentWARNING: The LEDs will flash brightly on power up.1. Enter the enrollment mode through installer programming, see section [898].2. Power up the outdoor siren by activating the pre-installed battery (plug the batterycable into the battery connector located inside the backplate to activate the battery.) Ifit is already powered up, press and release the tamper switch.3. The outdoor siren sends a request to the security panel to enroll on the system.4. The keypad displays the electronic serial number which must be confirmed by keying in[*]. If the electronic serial number is incorrect, Press [#] and repeat this step.5. Select the module number that the device should be enrolled as.NOTE: The electronic serial number is a 8-digit alphanumeric number located on asticker on the wireless device. 6. Repeat starting from step 2. to enroll each additional outdoor siren.Serial Number Programming1. Enter the enrollment mode through installer programming, see section [804].2. Select the module number that the device will be enrolled as. Sections [301]-[304] forsirens.3. Enter the serial number using the keypad. Placement TestPerform a placement test to ensure there is sufficient signal strength at the desired mount-ing location for proper communication between the security panel and the siren.1. Place the security panel into placement test, see section [906].2. Start the placement test by tampering the outdoor siren being tested.3. The siren will respond with 1 strobe flash and 1 beep if the location is “Good”. If thesiren is at a “Bad” location then it will respond with 3 strobe flashes and 3 beeps.WARNING: Wear hearing protection when installing the outdoor siren.Physical InstallationThe outdoor siren is mounted onto a flat surface, such as the outside of a building. A widevariety of mounting surfaces are acceptable but the mounting material must be able tosupport the weight of the siren.NOTE: The wall tamper switch must remain closed when the outdoor siren ismounted.1. Open the WT4911 by lifting the frontcover up from the siren bottom until itseparates from the backplate.2. If the battery is not already activated,plug the battery cable into the batteryconnector, see figure 2.3. Position the backplate on a flat mount-ing surface and mark this location.4. Secure the backplate to the mountingsurface with all the screws provided forthis purpose (4 screws). A screw must be installed in the tamper switch portion ofthe backplate.5. Carefully hinge then snap the front cover back onto the backplate, making sure it iscorrectly aligned, see figure 1.6. Secure the front cover to the backplate with 2 front cover screws. The remainingscrews are spares.Battery ReplacementNOTE: Please contact your local distributor to obtain a replacement battery.The security panel will indicate when the battery is low and requires replacement. The bat-tery must be replaced by a TRAINED SERVICE PERSON ONLY. REPLACE ONLY WITHTHE TYPE RECOMMENDED BY THE MANUFACTURER. Open the front cover and installthe battery, observing the polarity as indicated by the engraving. If the battery is installedincorrectly, in the reverse polarity, the outdoor siren will not work. Under typical use theWT4911 is capable of operating on battery power alone for 4 years without having toreplace the battery (under normal operating conditions). Do not try to recharge thebattery. Disposal of used batteries must be made in accordance with the wasterecovery and recycling regulations in your area.Configuration and TestingUse the keypad interface to setup the WT4911 siren options supported by the main panel(see table below).NOTE: The wireless keypad receives the temperature from the outdoor sirenenrolled in the lowest slot.IMPORTANT: The equipment is FIXED, WALL MOUNT and shall be installedin the position specified in these instructions. The equipment enclosure must beFULLY ASSEMBLED and CLOSED, with all the necessary screws/tabs andsecured to a wall before operation. Internal wiring must be routed in a manner thatprevents: Excessive strain on wire and on terminal connections; Loosening of termi-nal or connections; Damage of conductor insulation. • WARNING: Never installthis equipment OR replace the battery pack during a lightning storm! Never touchuninsulated wires or terminals unless the battery pack has been disconnected. •Instruct the END USER to: DO NOT attempt to service this product; Opening orremoving covers may cause exposure to dangerous voltages or other risks. ANY ser-vicing shall be referred to TRAINED service personnel only. • DO NOT THROWthe battery pack into a fire or water. Disposing the battery pack in a fire will causerupture and explosion; DO NOT DISPOSE of the waste battery as unsorted Thy-onil Chloride waste. Consult your local rules and/or laws regarding recycling of thisLithium battery pack; It will help protect the environment by reducing the number ofbatteries consumed. Some of the materials that are found within the battery couldbecome toxic if not disposed of properly and may affect the environment, and indi-rectly everybody’s health. This product contains a Lithium Thionyl Chloride non-rechargeable battery pack; Due to this fact, the equipment shall be Installed, Main-tained and Services by SERVICE PERSONS ONLY; ONLY TRAINED TECHNI-CIANS have the mandate to replace the battery pack! Risk of fire OR explosion ifthe battery pack is not properly connected; Avoid short circuit; Do not expose batter-ies to temperatures above 100 C; Do not use water in case of battery leakage. Referto the MSDS of battery for more details.WT4911 Two-Way Wireless Outdoor SirenInstallation InstructionsHumidity (max): 93% R.H. Operating Temperature: -35°C to 70°C (-31°F to 158°F)Operating Frequency: 433.92 MHz Temperature Range for UL/ULC: -35°C to 66°C Battery Life: 3-5 years (typical usage) Low Battery Level: 3.15V pre-determinedAlarm Signals-Output Level:105dB @1m Weight: 1.8lbs and IP rating: 34Battery: D size 3.6V Lithium Thionyl Chloride (ER34615M, Able) (WT4911-BATTERY, Custom Made Battery Pack lithium PTC protected)Compatible control panels: PC9155-433, PC9155D-433, PC9155G-433Siren # Serial Number[301]#1[302]#2[303]#3[304]#429007530R002DG009055Figure 1. Open (Close) Front CoverFigure 2. Outdoor Siren Backplate1 Front cover mounting screws (x4)2Backplate hinge (x2)3 Tamper (siren test button)4 Battery pack – custom made5 Battery cable6 Battery connector7 Mounting hole (x5)8 Front cover screw hole (x2)1245638++-7DG009051Programming Section OptionsSiren:Siren#1[311]Siren#2[312]Siren#3[313]Siren#4[314]1. Alarm sounds Enabled2. to 4. Not Available5. Bell Squawks Enabled6. Strobe Enabled7. Strobe follows BTO8. Siren Tamper Enabled1. Alarm sounds Disabled2. to 4. Not Available5. Bell Squawks Disabled6. Strobe Disabled7. Strobe follows Alarm Condi-tion8. Siren Tamper DisabledGlobal Siren:Sirens#1-4 [320]1. Tamper Activates Siren/Strobe2. Pre-Alarm Signal Enabled3. Strobe Squawks Enabled4 to 8. For Future Use1. Tamper does not Activate Siren/Strobe2. Pre-Alarm Signal Disabled3. Strobe Squawks Disabled4. to 8. For Future UseMax. Siren Time:Sirens#1-4 [330] Maximum Siren Activation Time |_|_|_| Valid entries are 000-255 minutes, Default 010NOTE: For UL/ULC residential fire and burglary installations setmaximum activation time to 5 minutes.
FCC Compliance StatementCAUTION: Changes or modifications not expressly approved by DigitalSecurity Controls could void your authority to use this equipment. Thisdevice complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.IC: 160A-WT4911 The term ‘IC:’ before the radio certification numberonly signifies that Industry Canada technical specifications were met.This Class B digital apparatus complies with Canadian ICES-003. Cetappareil numérique de la classe B est conforme à la norme NMB-003 duCanada.Limited WarrantyDigital Security Controls warrants that for a period of 12 months from thedate of purchase, the product shall be free of defects in materials andworkmanship under normal use and that in fulfilment of any breach ofsuch warranty, Digital Security Controls shall, at its option, repair orreplace the defective equipment upon return of the equipment to its repairdepot. This warranty applies only to defects in parts and workmanshipand not to damage incurred in shipping or handling, or damage due tocauses beyond the control of Digital Security Controls such as lightning,excessive voltage, mechanical shock, water damage, or damage arisingout of abuse, alteration or improper application of the equipment. Theforegoing warranty shall apply only to the original buyer, and is and shallbe in lieu of any and all other warranties, whether expressed or impliedand of all other obligations or liabilities on the part of Digital Security Con-trols. Digital Security Controls neither assumes responsibility for, norauthorizes any other person purporting to act on its behalf to modify or tochange this warranty, nor to assume for it any other warranty or liabilityconcerning this product. In no event shall Digital Security Controls be lia-ble for any direct, indirect or consequential damages, loss of anticipatedprofits, loss of time or any other losses incurred by the buyer in connectionwith the purchase, installation or operation or failure of this product.Warning: Digital Security Controls recommends that the entire sys-tem be completely tested on a regular basis. However, despite fre-quent testing, and due to, but not limited to, criminal tampering orelectrical disruption, it is possible for this product to fail to performas expected. Important: Changes or modifications not expresslyapproved by Digital Security Controls could void the user’s authorityto operate this equipment.IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Prod-ucts and Components is copyrighted and is purchased under the following license terms:• This End-User License Agreement (“EULA”) is a legal agreement betweenYou (the company, individual or entity who acquired the Software and anyrelated Hardware) and Digital Security Controls, a division of Tyco SafetyProducts Canada Ltd. (“DSC”), the manufacturer of the integrated securitysystems and the developer of the software and any related products or com-ponents (“HARDWARE”) which You acquired. • If the DSC software product (“SOFTWARE PRODUCT” or “SOFT-WARE”) is intended to be accompanied by HARDWARE, and is NOTaccompanied by new HARDWARE, You may not use, copy or install theSOFTWARE PRODUCT. The SOFTWARE PRODUCT includes com-puter software, and may include associated media, printed materials, and“online” or electronic documentation. • Any software provided along with the SOFTWARE PRODUCT that isassociated with a separate end-user license agreement is licensed to Youunder the terms of that license agreement. By installing, copying, downloading, storing, accessing or otherwise using theSOFTWARE PRODUCT, You agree unconditionally to be bound by the termsof this EULA, even if this EULA is deemed to be a modification of any previ-ous arrangement or contract. If You do not agree to the terms of this EULA,DSC is unwilling to license the SOFTWARE PRODUCT to You, and Youhave no right to use it.SOFTWARE PRODUCT LICENSEThe SOFTWARE PRODUCT is protected by copyright laws and international copy-right treaties, as well as other intellectual property laws and treaties. The SOFTWAREPRODUCT is licensed, not sold. 1. GRANT OF LICENSE This EULA grants You the following rights:(a) Software Installation and Use - For each license You acquire, You may have onlyone copy of the SOFTWARE PRODUCT installed. (b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed,accessed, displayed, run, shared or used concurrently on or from different computers,including a workstation, terminal or other digital electronic device (“Device”). In otherwords, if You have several workstations, You will have to acquire a license for eachworkstation where the SOFTWARE will be used.(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT,but You may only have one copy per license installed at any given time. You may use theback-up copy solely for archival purposes. Except as expressly provided in this EULA,You may not otherwise make copies of the SOFTWARE PRODUCT, including theprinted materials accompanying the SOFTWARE.2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS (a) Limitations on Reverse Engineering, Decompilation and Disassembly - You maynot reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, exceptand only to the extent that such activity is expressly permitted by applicable law not-withstanding this limitation. You may not make any changes or modifications to theSoftware, without the written permission of an officer of DSC. You may not remove anyproprietary notices, marks or labels from the Software Product. You shall institute rea-sonable measures to ensure compliance with the terms and conditions of this EULA.(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a singleproduct. Its component parts may not be separated for use on more than one HARD-WARE unit.(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE withHARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE asa single integrated product. In this case, the SOFTWARE PRODUCT may only be usedwith the HARDWARE as set forth in this EULA.(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You maynot make it available to others or post it on a server or web site.(e) Software Product Transfer - You may transfer all of Your rights under this EULAonly as part of a permanent sale or transfer of the HARDWARE, provided You retain nocopies, You transfer all of the SOFTWARE PRODUCT (including all component parts,the media and printed materials, any upgrades and this EULA), and provided the recipi-ent agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, anytransfer must also include all prior versions of the SOFTWARE PRODUCT.(f) Termination - Without prejudice to any other rights, DSC may terminate thisEULA if You fail to comply with the terms and conditions of this EULA. In such event,You must destroy all copies of the SOFTWARE PRODUCT and all of its componentparts.(g) Trademarks - This EULA does not grant You any rights in connection with anytrademarks or service marks of DSC or its suppliers.3. COPYRIGHT - All title and intellectual property rights in and to theSOFTWARE PRODUCT (including but not limited to any images, photo-graphs, and text incorporated into the SOFTWARE PRODUCT), the accom-panying printed materials, and any copies of the SOFTWARE PRODUCT, areowned by DSC or its suppliers. You may not copy the printed materialsaccompanying the SOFTWARE PRODUCT. All title and intellectual propertyrights in and to the content which may be accessed through use of the SOFT-WARE PRODUCT are the property of the respective content owner and maybe protected by applicable copyright or other intellectual property laws andtreaties. This EULA grants You no rights to use such content. All rights notexpressly granted under this EULA are reserved by DSC and its suppliers.4. EXPORT RESTRICTIONS - You agree that You will not export or re-export theSOFTWARE PRODUCT to any country, person, or entity subject to Canadian exportrestrictions. 5. CHOICE OF LAW - This Software License Agreement is governed by the laws ofthe Province of Ontario, Canada.6. ARBITRATION - All disputes arising in connection with this Agreement shall bedetermined by final and binding arbitration in accordance with the Arbitration Act, andthe parties agree to be bound by the arbitrator’s decision. The place of arbitration shallbe Toronto, Canada, and the language of the arbitration shall be English.7. LIMITED WARRANTY(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUTWARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEETYOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BEUNINTERRUPTED OR ERROR-FREE. (b) CHANGES IN OPERATING ENVI-RONMENT - DSC shall not be responsible for problems caused by changes in theoperating characteristics of the HARDWARE, or for problems in the interaction of theSOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OFRISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDI-TIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABIL-ITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BELIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TOLICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS(CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THEEXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL ORINCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TOYOU. (d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINSTHE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALLOTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDINGALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILI-TIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSCNEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTINGTO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY,NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CON-CERNING THIS SOFTWARE PRODUCT. (e) EXCLUSIVE REMEDY AND LIMI-TATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BELIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECTDAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CON-TRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THE-ORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OFPROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATEDEQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENTEQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME,THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURYTO PROPERTY. WARNING:DSC recommends that the entire system be completely tested on a regularbasis. However, despite frequent testing, and due to, but not limited to, crimi-nal tampering or electrical disruption, it is possible for this SOFTWAREPRODUCT to fail to perform as expected.The complete R&TTE Declaration of Conformity can be found at http://www.dsc.com/listings_index.aspx. © 2009 Digital Security Controls, Toronto, Canada Technical Support: 1-800-387-3630 (Canada & U.S.) or 905-760-3036 • www.dsc.comPrinted in CanadaThis equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules.

Navigation menu