Tyco Safety Canada 09WT4989 Wireless Security Access Key User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1052757
Application ID	PmeaD11S4I5rTjCodPpmhg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	194.84kB (2435526 bits)
Date Submitted	2009-01-07 00:00:00
Date Available	2009-01-07 00:00:00
Creation Date	2005-04-18 16:30:37
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2008-11-28 14:19:40
Document Title	DRAFT1B-29007536R001_WT4989 2-WAY KEY FOB_INIS_ENG.fm
Document Creator	FrameMaker 8.0
Document Author:	ElChan

Operating Instructions
IMPORTANT: This equipment shall be used in an environment that provides
the pollution degree max. 2 in NON-HAZARDOUS locations ONLY.
The WT4989 is a five-button two-way wireLCD ICONS
less key with an LCD icon display and a
built-in buzzer. The LCD provides display
icons that come on to show the system status when the Status Request button is
pressed. In addition, the buzzer will “beep”
to audibly indicate a button was pressed, or
that the wireless key has sent a command to
the control panel. The wireless key communicates with compatible wireless receivers
(i.e., 9155 security systems) to allow you to
arm, disarm and confirm your requested actions, as well as other keypad functions
with the convenience of wireless portability. Together with your installer, you can
decide which functions you wish to have accessible from your portable key. To activate, press and hold a button for approximately 1 second*. Note that some key
functions require a 3 second** press. The LCD display backlighting and antenna
icon turn on and the buzzer beeps once, indicating that a button has been pressed.
These actions also confirm that a signal has been sent to the control panel receiver.

Specifications
How to Enroll the WT4989
Control Panel System Status Display
This section describes how to set up and program your remote, this should be
done by the installer. The following outlines the basic steps for programming and
enrolling this device on PowerSeries receivers. For additional options, or for other
receivers, please refer to the specific receiver Installation Manual.
The table below summarizes the possible main system statuses that can be shown
by the WT4989 LCD display.
Step 1-Enroll the Device
Quick Enrollment
Section [898], enter through installer programming.
Press any key on the wireless device to activate it.
The Keypad will display the 8-digit ESN, confirm by pressing [*].
Repeat from step 2 to enroll additional remotes.
Program Electronic Serial Number (ESN)
1. Section [804], subsections [101]- [101]Key 1
[116].
2. Enter the 8-digit ESN located on the [102]Key 2
back of the unit.
Section [804], subsections [141] - [156]
3 0 Button 4 Panic
0 4 Button 2 Away Arming
1 3 Buttons (1+2) Command Output 1
The Default Button Functions
2 7 Button 3 Disarm
1 4 Buttons (3+4) Command Output 2
angle icon ( ) flashes briefly before the keyfob turns off. To unlock the keys,
press this button for 3 seconds.
Away Arming: Press to arm your sysStay Arming: Press to arm
your system in Stay mode. All
tem. Interior and exterior zones will be
perimeter zones are active but
armed.
interior zones remain inactive.
Panic Alarm**: Press to notify your
Disarm: Press to disarm your central monitoring station of a situation
requiring police.
system.
Command Output 1**
Command Output 2** Press
Press both at the same time to acti- both at the same time to activate the
assigned output.
vate the assigned output.
Device Programming
Transmit Default Serial
Mode** Press all at the same time to proNumber** Press both at the same gram optional button functions. This should be
done
by
the
installer.
the battery icon flashes.
time to send the serial number.
Other WT4989 options are available in order to program the best possible combination to suit specific needs. For UL Listed installations, refer to the control panel's
Installation Manual for details.
How to Program the WT4989 Options
Changing the programming will affect operation. This should be done by the installer. To program WT4989 Options: (1) Press and hold all 4 buttons at the same time until the
icon comes on and begins to flash. (2) Choose a WT4989 Programmable Option from the
table. These options have toggle features, to return to the default, repeat steps 1 and 2.
To Program this Option
Do This
Remove the Keypress Beeps.
Press the (
Remove the 3-Second Delay on (
Turn off the System Disarm (
) key. Press the (
) key.
) key.
) key.
Press the (
) key.
Turn off the (
) key.
Press the (
) key.
Turn off the (
)key.
Press the (
) key.
Turn off the Backlighting function.
(F) Disarmed - Not Ready
(S) Away - Armed
(S) Stay - Armed
(S/F=Steady or Flashing, icon state will
(S) Night - Armed
depend on the system state)
Keyfob Status
(S/F)Exit Delay-Away Arming
(S) WT4989 Low Battery
(S/F) Exit Delay-Stay Arming
(F) Device Programming
(F) Critical Low Battery
(S/F) Exit Delay-Night Arming
Replacing the Batteries
0 3 Button 1 Stary Arming
Keylock** Press and hold this button for 3 seconds to lock the keys. The Tri-
(F) Active Alarm
(F) *9 Armed - Away
(F) *9 Armed - Stay
(F) *9 Armed - Night
(S) Disarmed - Ready
(F) Keylock enable
Step 2-Program Function Buttons
Operating Frequency: 433 MHz; Wireless Range: (n/a)m (outdoor, line of sight);
Batteries: (2) 3V Lithium (CR2032); Dimensions (LxWxH): 75mm x 40mm x
14mm; Weight: 41g; Water Resistant
Status Request Press this button for 1 second to view the control panel
system status via the LCD display icons.
(S) Alarm in Memory
(S) System Trouble
The WT4989 is enrolled by Quick Enrollment or Serial Number Programming.
1.
2.
3.
4.
ICON (S=Steady, F=Flashing) SYSTEM STATUS
Press the ( )+(
keys at the same time.
NOTE: Do not press any other button while in Programming mode.
NOTE: For UL Listed installations, the 'Arm/Disarm Bell Squawk' feature of
the control panel must be enabled. The 3-second delay on the Panic key must
not be disabled. The Bell Squawk must be heard from outside the premises.
Arming/Disarming confirmations must be indicated by the keyfob LCD display. Refer to the control panel's Installation Manual for details.
Under normal conditions the batteries last 3 years. During each button press the keyfob sends the status of its
battery to the control panel receiver. If the battery is low,
the battery icon on the LCD display comes ON. If the battery has reached a critically low state the battery icon
flashes. To replace the battery, remove the top cover by
inserting a coin into the slot located on the center bottom
and twist to expose the batteries. Replace both batteries
with lithium 3V batteries (CR-2032), see diagram. 9043
NOTE: The polarity of the battery must be observed, as
shown in the diagram. REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER. Keep away from
small children. If batteries are swallowed, promptly see a doctor. Do
not try to recharge these batteries. Disposal of used batteries must
be made in accordance with the waste recovery and recycling regulations in your area
Belt Clip Assembly
Compatibility
The WT4989 is compatible
with the following receivers:
PC9155-433, PC9155D-433
and PC9155G-433
Limited Warranty
Digital Security Controls warrants that for a period of 12 months from the
date of purchase, the product shall be free of defects in materials and
workmanship under normal use and that in fulfilment of any breach of
such warranty, Digital Security Controls shall, at its option, repair or
replace the defective equipment upon return of the equipment to its repair
depot. This warranty applies only to defects in parts and workmanship
and not to damage incurred in shipping or handling, or damage due to
causes beyond the control of Digital Security Controls such as lightning,
excessive voltage, mechanical shock, water damage, or damage arising
out of abuse, alteration or improper application of the equipment. The
foregoing warranty shall apply only to the original buyer, and is and shall
be in lieu of any and all other warranties, whether expressed or implied
and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor
authorizes any other person purporting to act on its behalf to modify or to
change this warranty, nor to assume for it any other warranty or liability
concerning this product. In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of anticipated
profits, loss of time or any other losses incurred by the buyer in connection
with the purchase, installation or operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or
electrical disruption, it is possible for this product to fail to perform
as expected. Important: Changes or modifications not expressly
approved by Digital Security Controls could void the user’s authority
to operate this equipment.
FCC Compliance Statement
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls could void your authority to use this equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IC: 160A-WT4989 The term ‘IC:’ before the radio certification number
only signifies that Industry Canada technical specifications were met.
This Class B digital apparatus complies with Canadian ICES-003. Cet
appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
This product meets the requirements of Class II, Grade 2 equipment as per EN50131-1 and EN50131-4 Standards. The power
supply is Type C as per EN50131-6 Standard.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is purchased under the following license terms:
• This End-User License Agreement (“EULA”) is a legal agreement between
You (the company, individual or entity who acquired the Software and any
related Hardware) and Digital Security Controls, a division of Tyco Safety
Products Canada Ltd. (“DSC”), the manufacturer of the integrated security
systems and the developer of the software and any related products or components (“HARDWARE”) which You acquired.
• If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT
accompanied by new HARDWARE, You may not use, copy or install the
SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials, and
“online” or electronic documentation.
• Any software provided along with the SOFTWARE PRODUCT that is
associated with a separate end-user license agreement is licensed to You
under the terms of that license agreement.
©2008 Digital Security Controls, Toronto, Canada • www.dsc.com
By installing, copying, downloading, storing, accessing or otherwise using the
SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms
of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this EULA,
DSC is unwilling to license the SOFTWARE PRODUCT to You, and You
have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE
PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only
one copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed,
accessed, displayed, run, shared or used concurrently on or from different computers,
including a workstation, terminal or other digital electronic device (“Device”). In other
words, if You have several workstations, You will have to acquire a license for each
workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT,
but You may only have one copy per license installed at any given time. You may use
the back-up copy solely for archival purposes. Except as expressly provided in this
EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including
the printed materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may
not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except
and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the
Software, without the written permission of an officer of DSC. You may not remove
any proprietary notices, marks or labels from the Software Product. You shall institute
reasonable measures to ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single
product. Its component parts may not be separated for use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with
HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE as
a single integrated product. In this case, the SOFTWARE PRODUCT may only be used
with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may
not make it available to others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA
only as part of a permanent sale or transfer of the HARDWARE, provided You retain no
copies, You transfer all of the SOFTWARE PRODUCT (including all component parts,
the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any
transfer must also include all prior versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this
EULA if You fail to comply with the terms and conditions of this EULA. In such event,
You must destroy all copies of the SOFTWARE PRODUCT and all of its component
parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any
trademarks or service marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the
SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PRODUCT,
are owned by DSC or its suppliers. You may not copy the printed materials
accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which may be accessed through use of the
SOFTWARE PRODUCT are the property of the respective content owner and
may be protected by applicable copyright or other intellectual property laws
and treaties. This EULA grants You no rights to use such content. All rights
not expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the
SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export
restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the laws of
the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement shall be
determined by final and binding arbitration in accordance with the Arbitration Act, and
the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall
be Toronto, Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT
WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL
MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE
WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible
for problems caused by changes in the operating characteristics of the HARDWARE, or
for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF
RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL
BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY
YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE
ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER
WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES
ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO
ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR
TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING
THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO
CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH
OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT
ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES,
DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES,
INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING:
DSC recommends that the entire system be completely tested on a regular
basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE
PRODUCT to fail to perform as expected.
Printed in Canada

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : DRAFT1B-29007536R001_WT4989 2-WAY KEY FOB_INIS_ENG.fm
Creator                         : ElChan
Create Date                     : 2005:04:18 16:30:37Z
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2008:11:28 14:19:40-05:00
Metadata Date                   : 2008:11:28 14:19:40-05:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:6462c03f-d63d-487b-9340-15572d76304c
Instance ID                     : uuid:72b825a2-27ec-4940-8c4c-a7507e64d9e2
Page Count                      : 2
Author                          : ElChan

EXIF Metadata provided by EXIF.tools