Tyco Safety Canada 10WS4920 Wireless Alarm Repeater User Manual 29007856R001 WS4920 1 0 INS ENG

Digital Security Controls Ltd. Wireless Alarm Repeater 29007856R001 WS4920 1 0 INS ENG

User Manual

NOTE: Use these instructions in conjunction with the installation manual of the alarm panel with which this equipment is intended to be used.WARNING: READ and SAVE These Instructions! Follow All WARNINGS AND INSTRUCTIONS specified within these instruction and/or on the equipment.WS4920 v1.0Installation Instructions29007856R001
SAFETY INSTRUCTIONS for WS4920 WIRELESS REPEATERIMPORTANT:This equipment, WS4920 WIRELESS REPEATER 1.0 shall be used installed and used within an environment that provides the pollution degree max 2 and overvoltages category II NONHAZARDOUS LOCATIONS, indoor only. The equipment is FIXED and DIRECT PLUG IN powered from the mains; it is designed to be installed by Service Persons only; [Service Person isdefined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and of mea-sures to minimize the risks to that person or other persons. 1. The equipment is installed in a FIRE ENCLOSURE.2. If during the installation a knockout is removed, it is the installer's responsibility to ensure that the same degree of protection for the enclosure is provided by the use of bushings,fittings, etc.3. The enclosure must be secured to the building structure before operation.4. Internal wiring must be routed in a manner that prevents:•Excessive strain on wire and on terminal connections;•Loosening of terminal; connections;•Damage of conductor insulation5. It is the end-user and/or installer's responsibility to ensure that the disposal of the used batteries (battery pack) is made according to the waste recovery and recycling regulationsapplicable to the intended market.WARNING: When using equipment connected to the MAINS, always follow basic safety instructions. Refer to the SAFETY INSTRUCTIONS provided with this product; save them for(future) reference. Instruct the end-user regarding the safety precautions that shall be observed when operating this equipment.SAFETY precautions required during installation:• NEVER install this EQUIPMENT during A Lightning Storm!• NEVER touch uninsulated wires or terminals unless the Direct Plug In transformer has been disconnected • Ensure that Cables are positioned so that accidents cannot occur. Connected Cables must NOT be subject to excessive mechanical strain• Use Only the Power Supply supplied with this equipment. Use of unauthorized power supplies may cause damage the repeater!!!• The AC Socket/Outlet powering the equipment shall be located near the equipment and shall be easily accessible. • Do NOT locate this product where persons will walk on the secondary circuit cable(s). • Do NOT use extension cords to PLUG-IN the Power Supply of this equipment.• AVOID setting up the equipment near heaters, air conditioners, ventilators, and/or refrigerators • Do NOT connect to electrical outlets on the same circuit as large appliances.• Do NOT select a place exposed to direct sunlight, excessive heat, moisture, vapors, chemicals or dust.• Do NOT install this Equipment near water. (e.g., bath tub, wash bowl, kitchen/laundry sink, in a wet basement, or near swimming pool, etc.).• Do NOT install this equipment and its accessories in areas where there is a risk of explosion.• Do NOT connect this equipment to electrical outlets controlled by wall switches or automatic timers; avoid interference sources.WARNING: THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS INTENDED TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENTMUST BE QUICKLY DISCONNECTED. IT IS IMPERATIVE THAT ACCESS TO THE MAINS PLUG AND ASSOCIATED MAINS SOCKET/OUTLET, IS NEVER OBSTRUCTED.
The WS4920 is a wireless repeater designed toextend the range of DSC one-way wirelesstransmitters and to improve signal qualitybetween the transmitter and the receiver. Usethe WS4920 to remedy transmission problemscaused by excessive noise or other interference,or by long distances between devices andreceivers. Up to 4 repeaters can be installed peralarm system.The WS4920 is compatible with all DSC 433MHz one-way wireless transmitters, receivers andalarm panels. It can also be used with 2-wayalarm panels, but only for 1-way devices.Specifications• Temperature range: 0°C to +50°C (32°F-122°F)• Humidity (Max): 5% - 93% R.H. non condensing• Transformer: 16VAC, 20VA• Battery backup time: 24 hours• Battery charging rate: 80% within 24 hours• Operating frequency: 433.92 MHz• Dimensions: H6.96, W4.47, D1.33 in.• Weight: 2 lb.UnpackingEnsure your package includes the following:Controls and IndicatorsThe WS4920 has three LEDs on the front usedto communicate information. The LEDs indicate the following:In addition, the WS4920 has an internal Pro-gramming button to place the repeater intoEnroll/Placement modes. It also includes ajumper to prevent RF jam troubles from beingsent to the panel. When the jumper is open, RFjam troubles are not transmitted.Install the WS4920 in the following order:A.Temporarily mount in preferred locationB.Connect power (battery first then AC)C. Receiver placement test (detects interferencebetween repeater and wireless devices)Introduction• One WS4920• One direct plug-in transformer (kit dependant)• Mounting hardware pack, including plastic wall plugs and screws• Installation instructionsLED Normal Mode(cover on)Installer Mode(cover off)Green On: AC presentFlashing: No AC, battery goodOff: No AC, low or dead battery1 flash: EnrolledFlashing: Placement test activeRed On: Battery not connectedFlashing: Low batteryOff: Battery good (if AC on)Flashing: Zone not enrolledYellow On: RF jam presentOff: No RF jamOn: Receiver place-ment test “bad”Off: Receiver place-ment test “good”Green YellowRedInstallationProgrammingButton
D.Enroll with alarm panelE. Placement test with alarm panel (Detects interfer-ence between repeater and panel)F. Enroll/Placement test wireless devices with repeater G. Permanently mount WS4920.NOTE: When enrolling and placement testing theWS4920 with the alarm panel, refer to the panelinstallation instructions for the appropriate pro-gramming sections.A: Temporarily Mount WS4920Select a suitable location for the repeater. Usethe following list as a guide:•Locate device near a power outlet•Location should be free from vibration and shock•Mount on a flat, stable surface•Ideal location is mid-way between the wire-less transmitter and receiverDo not permanently mount the repeater until ithas been placement tested.Temporarily mount the unit using tape or othernon-permanent method. If the selected locationfails the placement test, the device must berepositioned.B: Connect Power Connect back-up battery first then AC.To connect the battery:1.Gently pry front cover from chassis using smallslotted screwdriver in holes provided.2.Connect battery cable to connector on PC board. NOTE: Low Battery Transmission Delay program-ming option (section 377 on alarm panel) must beno more than 1 day as battery backup time is 24hours. To connect the AC adaptor:1.Run AC wire through wiring channel on back ofrepeater and pass through hole in chassis.2.Connect AC wires to terminals on PC board.3.Route wire around retaining bracket to secure.4.Plug AC adaptor into wall outlet.C: Placement Testing the WS4920 Receiver Receiver placement test ensures the WS4920 islocated in an area with low noise and interfer-ence and can successfully receive signals fromone-way wireless devices. To perform a Receiver Placement test:1.Press and hold Programming button for 3seconds to enter Programming mode. The“Mode Entered” tone sounds. Receiver Place-ment Test is continuously active until Pro-gramming mode is exited, times out or thecover is put back on the unit. 2.If RF traffic level or noise floor level is toohigh, yellow LED turns on. If this occurs,reposition WS4920 until yellow LED turns off.3.To exit Enroll/Placement mode, press Pro-gramming button again for 3 seconds orplace cover back on WS4920. The “ModeExited” tone sounds.BatteryConnectorAC Terminals
D: Enrolling the WS4920The WS4920 has two Electronic serial numbers(ESN) that must be entered into the alarm panelduring enrollment. The first communicates super-visory and tamper status. The second identifiesbattery status (see note below).To quick enroll the WS4920 (available onselected alarm panels):1.Enter Wireless Enrollment mode on alarm panel(see panel installation instructions). 2.Tamper WS4920 to transmit first ESN.3.Confirm ESN on alarm panel. The panelprompts for zone number.4.Select and accept zone number for repeater.5.Press Programming button on WS4920 totransmit second ESN.6.Confirm ESN on alarm panel and select zonewhen prompted. Once zone is confirmed,WS4920 is enrolled.To manually enroll the WS4920, consult the alarmpanel installation manual.NOTE: Disable tamper transmission programming(options ([330]-[336] on control panel) for thesecond zone. This prevents low battery troubles/restores, caused by momentary AC loss, from beingreported to the monitoring station. A tamper islogged in the event buffer. Both zones should beprogrammed as a non-alarm zone type.E: Placement Testing the WS4920For optimal performance between the WS4920and the alarm panel, the repeater should belocated in an area of low RF interference. To test the RF link between the WS4920 andthe alarm panel:1.Place alarm panel into placement test (seepanel installation instructions) and select zonewhere first serial number is enrolled.2.Tamper the WS4920.•If alarm panel receives a strong signal, thepanel squawks the siren once and “Locationis Good” is displayed on alarm keypad.•If alarm panel receives a weak signal, the panelsquawks the siren three times and “Location isBad” is displayed on alarm keypad.3.If alarm system indicates no response, repo-sition WS4920 and repeat test. Repeatershould only be placed in a location wheremultiple good results are received.F: Quick Enroll/Placement Testing DevicesUp to 164 1-way wireless devices can beenrolled on the WS4920. During the first 4hours of power up, the WS4920 can be placedinto Enroll/Placement test modes. After the 4hour time-out, access to these modes is deniedand the unit must be powered up again to enterEnroll/Placement mode.To both enroll and placement test a device atthe same time:1.Press and hold Programming button for 3 sec-onds. “Mode Entered” tone sounds. TheWS4920 is now in Enroll/Programming mode.2.Trip and restore zone to be enrolled 3 times:•Door and window contact open/close or tam-per/restore•PIR and other stationary devices tamper/restore•Panic pendant 3 to 4 button presses •Wireless key 3 separate button presses3.Once repeater has received signal from zone,Green LED lights for 1 second and sounderemits “Zone Enrolled” tone.NOTE: •If another zone is tripped during the enrollsequence, the enroll process must be restarted.•A repeater can not enroll another repeater.•Stationary (permanently mounted) devicesshould only be enrolled on one repeater. Theonly exception is in Residential Fire Installa-tions, where smoke detectors must be enrolledwith at least 2 repeaters.•Fobs and panic pendants may be enrolledwith multiple repeaters.•If an enrollment is attempted after all 164device slots have been filled, the repeateremits the “Error” tone to indicate that no fur-ther devices may be enrolled.4.After zone is enrolled, trip zone again to per-form placement test. Green LED flashes if sig-nal is received. •If “GOOD Zone Placement” tone sounds,device location is satisfactory and unit maybe permanently mounted. NOTE: If the repeater tone can not be heard whiletesting the device, set the alarm panel into place-
ment test mode using the first repeater serial num-ber. The repeater placement test results aresounded through the alarm panel siren.•If “BAD Zone Placement” tone sounds, reposi-tion device and trip zone again. Continue until“GOOD Zone Placement” tone sounds.NOTE: Although good results may be obtained onthe repeater, bad results are still possible from thealarm panel due to collisions.5.Use above procedure to enroll and placementtest other zones.6.To exit, press Programming button again for3 seconds or place cover back on WS4920.“Mode Exited” tone sounds.Global Placement Testing DevicesTo placement test a 1-way wireless device afterthe initial enroll/placement test process:1.Press and hold Programming button for 3seconds. “Mode Entered” tone sounds. TheWS4920 is now in Global Placement Testmode. Each zone enrolled on repeater givesplacement test result when tripped.•If “GOOD Zone Placement” tone sounds,device location is satisfactory and unit maybe permanently mounted.•If “BAD Zone Placement” tone sounds, reposi-tion device and trip zone again. Continue until“GOOD Zone Placement” tone sounds.2.To exit, press Programming button again for3 seconds or place cover back on theWS4920. “Mode Exited” tone sounds.G: Mounting the WS4920Permanently mount the WS4920 only aftercompleting multiple successful placement tests.To mount the WS4920:1.Ensure AC wire is run through channel onback of repeater.2.Remove front cover and secure unit to wallthrough mounting holes using screws pro-vided. Use all 4 screws.3.Place cover back on WS4920.4.Plug AC adaptor into unswitched AC outlet.Restoring the WS4920 to Factory Defaults To restore factory default settings:1.Within 1 minute of power up, press and holdProgramming button for 10 seconds. Sounderbeeps after first second to indicate WS4920is in Installer mode. After 10 seconds,Repeater emits long tone and all LEDS light.2.Release Programming button and immedi-ately press and hold again for 10 seconds.After 10 seconds, WS4920 emits a long toneand all three LED’s flash.NOTE: The second button press must occur within30 seconds of the first or the WS4920 will exitEnroll/Placement mode.3.WS4920 beeps three times indicating Installermode exit. If installer mode exits before thereset is complete, due either to time-out ortamper, repeat the reset procedure.Replacing the BatteryReplace the backup battery when it no longerholds its charge.To replace the battery:1.Disconnect WS4920 from AC.2.Remove front cover from device.3.Disconnect battery cable from connector.4.Loosen screw on battery retention arm androtate arm aside. 5.Lift battery out of holder and insert new one.6.Reposition retention arm and tighten screw.7.Snap front cover back into place.8.Re-connect WS4920 to AC.ACMounting HoleMounting Hole
Limited Warranty Digital Security Controls warrants that for a period of 12 months from the date of purchase, theproduct shall be free of defects in materials and workmanship under normal use and that infulfilment of any breach of such warranty, Digital Security Controls shall, at its option, repair orreplace the defective equipment upon return of the equipment to its repair depot. This warrantyapplies only to defects in parts and workmanship and not to damage incurred in shipping orhandling, or damage due to causes beyond the control of Digital Security Controls such aslightning, excessive voltage, mechanical shock, water damage, or damage arising out ofabuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of anyand all other warranties, whether expressed or implied and of all other obligations or liabilitieson the part of Digital Security Controls. Digital Security Controls neither assumes responsibil-ity for, nor authorizes any other person purporting to act on its behalf to modify or to changethis warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall Digital Security Controls be liable for any direct, indirect or consequentialdamages, loss of anticipated profits, loss of time or any other losses incurred by the buyer inconnection with the purchase, installation or operation or failure of this product. Warning: Digital Security Controls recommends that the entire system be completely testedon a regular basis. However, despite frequent testing, and due to, but not limited to, criminaltampering or electrical disruption, it is possible for this product to fail to perform as expected.Important Information: Changes or modifications not expressly approved by Digital Secu-rity Controls could void the user’s authority to operate this equipment.FCC Compliance StatementCaution: Changes or modifications not expressly approved by Digital Security Controls couldvoid your authority to use this equipment.This equipment generates and uses radio frequency energy and if not installed and used prop-erly, in strict accordance with the manufacturer’s instructions, may cause interference to radioand television reception. It has been type tested and found to comply with the limits for ClassB device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules, whichare designed to provide reasonable protection against such interference in any residentialinstallation. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause interference to television or radio reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to cor-rect the interference by one or more of the following measures:• Re-orient the receiving antenna• Relocate the alarm control with respect to the receiver• Move the alarm control away from the receiver• Connect the alarm control into a different outlet so that alarm control and receiver are on dif-ferent circuits.If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4.IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Compo-nents is copyrighted and is purchased under the following license terms:• This End-User License Agreement (“EULA”) is a legal agreement between You (the com-pany, individual or entity who acquired the Software and any related Hardware) and DigitalSecurity Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the manufac-turer of the integrated security systems and the developer of the software and any relatedproducts or components (“HARDWARE”) which You acquired. • If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended tobe accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, Youmay not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCTincludes computer software, and may include associated media, printed materials, and“online” or electronic documentation. • Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You under the terms of that license agreement. • By installing, copying, downloading, storing, accessing or otherwise using the SOFT-WARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA,even if this EULA is deemed to be a modification of any previous arrangement or con-tract. If You do not agree to the terms of this EULA, DSC is unwilling to license theSOFTWARE PRODUCT to You, and You have no right to use it.SOFTWARE PRODUCT LICENSEThe SOFTWARE PRODUCT is protected by copyright laws and international copyrighttreaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCTis licensed, not sold. 1.GRANT OF LICENSE This EULA grants You the following rights:(a)Software Installation and Use - For each license You acquire, You may have only onecopy of the SOFTWARE PRODUCT installed. (b)Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed,displayed, run, shared or used concurrently on or from different computers, includinga workstation, terminal or other digital electronic device (“Device”). In other words, ifYou have several workstations, You will have to acquire a license for each workstationwhere the SOFTWARE will be used.(c)Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but Youmay only have one copy per license installed at any given time. You may use theback-up copy solely for archival purposes. Except as expressly provided in this EULA,You may not otherwise make copies of the SOFTWARE PRODUCT, including theprinted materials accompanying the SOFTWARE.2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS (a)Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.(b)Separation of Components - The SOFTWARE PRODUCT is licensed as a singleproduct. Its component parts may not be separated for use on more than oneHARDWARE unit.(c)Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE,then the SOFTWARE PRODUCT is licensed with the HARDWARE as a single integratedproduct. In this case, the SOFTWARE PRODUCT may only be used with theHARDWARE as set forth in this EULA.(d)Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not makeit available to others or post it on a server or web site.(e)Software Product Transfer - You may transfer all of Your rights under this EULA onlyas part of a permanent sale or transfer of the HARDWARE, provided You retain nocopies, You transfer all of the SOFTWARE PRODUCT (including all component parts,the media and printed materials, any upgrades and this EULA), and provided therecipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade,any transfer must also include all prior versions of the SOFTWARE PRODUCT.(f)Termination - Without prejudice to any other rights, DSC may terminate thisEULA if You fail to comply with the terms and conditions of this EULA. In suchevent, You must destroy all copies of the SOFTWARE PRODUCT and all of itscomponent parts.(g)Trademarks - This EULA does not grant You any rights in connection with anytrademarks or service marks of DSC or its suppliers.3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWAREPRODUCT (including but not limited to any images, photographs, and textincorporated into the SOFTWARE PRODUCT), the accompanying printed materials,and any copies of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. Youmay not copy the printed materials accompanying the SOFTWARE PRODUCT. Alltitle and intellectual property rights in and to the content which may be accessedthrough use of the SOFTWARE PRODUCT are the property of the respective contentowner and may be protected by applicable copyright or other intellectual propertylaws and treaties. This EULA grants You no rights to use such content. All rights notexpressly granted under this EULA are reserved by DSC and its suppliers.4. EXPORT RESTRICTIONS - You agree that You will not export or re-export theSOFTWARE PRODUCT to any country, person, or entity subject to Canadianexport restrictions. 5. CHOICE OF LAW - This Software License Agreement is governed by the lawsof the Province of Ontario, Canada.6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall be Toronto, Canada, and the language of the arbitration shall be English.7. LIMITED WARRANTY(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY.DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOURREQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BEUNINTERRUPTED OR ERROR-FREE.(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible forproblems caused by changes in the operating characteristics of theHARDWARE, or for problems in the interaction of the SOFTWARE PRODUCTwith non-DSC-SOFTWARE or HARDWARE PRODUCTS.(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - INANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOTSTATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANYPROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THEGREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THESOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSESOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OFLIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVELIMITATION MAY NOT APPLY TO YOU.(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIREWARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES,WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIEDWARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PARTOF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMESNOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITSBEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUMEFOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THISSOFTWARE PRODUCT.(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCESSHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL ORINDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT,NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGESINCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWAREPRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OFSUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME,PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, ANDINJURY TO PROPERTY. WARNING: DSC recommends that the entire system be completely tested on aregular basis. However, despite frequent testing, and due to, but not limited to,criminal tampering or electrical disruption, it is possible for this SOFTWAREPRODUCT to fail to perform as expected.
FCC COMPLIANCE STATEMENTCAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLYAPPROVED BY DIGITAL SECURITY CONTROLS COULDVOID YOUR AUTHORITY TO USE THIS EQUIPMENT. Thisequipment generates and uses radio frequency energyand if not installed and used properly, in strict accor-dance with the manufacturer’s instructions, may causeinterference to radio and television reception. It has beentype tested and found to comply with the limits for ClassB device in accordance with the specifications in Subpart“B” of Part 15 of FCC Rules, which are designed to pro-vide reasonable protection against such interference inany residential installation. However, there is no guaran-tee that interference will not occur in a particular installa-tion. If this equipment does cause interference totelevision or radio reception, which can be determined byturning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the fol-lowing measurers: Re-orient the receiving antenna, relo-cate the alarm control with respect to the receiver, Movethe alarm control away from the receiver, connect thealarm control into a different outlet so that alarm controland receiver are on different circuits. If necessary, theuser should consult the dealer or an experienced radio/television technician for additional suggestions. The usermay find the following booklet prepared by the FCC help-ful: “How to Identify and Resolve Radio/Television Inter-ference Problems.” This booklet is available from theU.S. Government Printing Office, Washington, D.C.20402, Stock # 004-000-00345-4.This Class B digital apparatus complies with CanadianICES-003.Cet appareil numérique de la classe B est conforme à lanorme NMB-003 du Canada.IC:160A-WS4920The term IC before the radio certification number signifiesthat the Industry Canada technical specifications were met.© 2010 Tyco International Ltd. and its Respective Com-panies. All Rights Reserved.The trademarks, logos, and service marks displayed onthis document are registered in the United States [orother countries]. Any misuse of the trademarks is strictlyprohibited and Tyco International Ltd. will aggressivelyenforce its intellectual property rights to the fullest extentof the law, including pursuit of criminal prosecutionwherever necessary. All trademarks not owned by TycoInternational Ltd. are the property of their respectiveowners, and are used with permission or allowed underapplicable laws.Product offerings and specifications are subject to changewithout notice. Actual products may vary from photos.Not all products include all features. Availability varies byregion; contact your sales representative.www.dsc.comPrinted in Canada

Navigation menu