Tyco Safety Canada 12WS4928 Wireless Holdup Switch User Manual

Digital Security Controls Ltd. Wireless Holdup Switch

user manual

WS4928 Holdup SwitchInstallation Instructions - For Service Persons OnlyThese instructions shall be used with the Installation Manual of the DSC wireless receiver and control panel with which this device is intended to be used.The WS4928 wireless holdup switch is intended for installation under a counter, desktop, switchboard or other concealed location.SpecificationsOut of the Box• 1 WS4928 module• 1 reset tool• 4 mounting screwsPowering the WS4928The WS4928 comes with the battery pre-installed. To activate, hold the WS4928 firmly in one hand and pull the plastic tab in the direction indicated.Locate TransmitterSelect the location where the WS4928 is to be mounted. NOTE: RF signals can be affected by metal objects, including metal doors or large mirrors. Such locations should be avoided, they can interfere with proper operation. Enrolling, Programming and PlacementEnroll the WS4928 by programming the 6-digit serial number (located on the WS4928) into the receiver. Once the WS4928 is enrolled, you must perform a Module Placement test to ensure the location you have chosen is suitable. Thefollowing outlines the basic steps for programming and enrolling this device on PowerSeries receivers. For additional options or for other receivers please refer to the specific receiver installation manuals.Step 1 – Program Electronic Serial Number (ESN) Section [804], subsections [01] – [64][01] Zone 1 ... [64] Zone 64Enter the 6 digit ESN located on the WS4928 into the next available zone slot.Step 2 – Program Zone DefinitionSection [001] – [004]Define corresponding zone with appropriate zone type [i.e., Holdup (12)].Step 3 – Enable Wireless Zone AttributeSection [101] – [164]Turn Option [8] ON (wireless zone attribute) in corresponding zone attribute section.All wireless devices must be tested for good signal strength from where they are positioned.Step 4 – Device Placement TestSection [904], subsections [01] – [64]Activate the switch. The panel will indicate the test result through the siren (and also through the keypad):1 bell squawk/beep on LCD keypad/LED 1 on LED keypad) indicates GOOD placement3 bell squawks/beeps on LCD keypad/LED 3 on LED keypad) indicates BAD placementIf the transmitter tests BAD, move the transmitter and repeat the Placement Test.Mounting the DeviceSecure the holdup switch to the mounting surface using the 4 mounting screws provided. NOTE: The WS4928 may be mounted horizontally or vertically. In horizontal installations, position the unit so that the finger-operated slide is acti-vated by pulling toward the user. In vertical installations, position the unit so that the finger-operated slide is activated by pulling downward by the user.OperationActivation - The WS4928 holdup switch is activated by placing a finger in the access hole and pulling the slide toward the user (downward in vertical mount installations). The alarm activation will be indicated locally at the device by thered tab on the unit. The device will remain latched in the alarm state until a manual reset is performed. Restoral - To restore the device, insert the reset tool into the two rectangular slots next to the alarm indicating tab. Ensure the flat (unbevelled) side is facing the red tab (see Figure A).Testing1. Notify the central station prior to testing the switch.2. Activate the switch.3. Reset the switch.4. Verify receipt of the alarm and restoral signal at the central station and provide notification that the test is completed.Tamper Switch & Wall TamperThe WS4928 comes equipped with case tamper detection. If the case is removed, the WS4928 will report a zone tamper to the control panel. For added security the WS4928 was designed to provide wall tamper monitoring as well.When using the wall tamper please do not install the device on surfaces made of soft materials.NOTE: A tamper switch is required for UL Listed commercial burglary/holdup installations.Replacing the BatteryTo replace the battery, insert a flathead screwdriver into either side of the transmitter unit and carefully twist to separate the top and bottom plastic (see Figure B). Once separated, the battery will be visible (please see Figure C). Removethe old battery and install new battery. Ensure correct polarity is observed. Dispose of used battery promptly. CAUTION: The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100C (212F) or dispose of in fire. Replace battery with one 3V lithium bat-tery, Panasonic CR2 or Duracell CR2 only. Use of another battery may present a risk of fire or explosion. Dispose of the used batteries as per local regulations. Keep away from children. NOTE: Model WS4928 is UL listed for commercial burglary/holdup applications in accordance with the following standards: UL636, UL1610.NOTE: Test unit at least once yearly. Dimensions: 95mm × 121mm × 38mm (3¾”x 4¾” x 1½”)Operating Temperature: UL/ULC: 0oC to 49oC (32oF to 120oF)Operating Humidity: 85% RHOperating Frequency: 433 MHzBattery: Duracell/Panasonic CR2 Lithium (2.2V low battery indication threshold)Battery Life: 5-8 years *Compatible Receivers: RF5132-433 with DSC control panel models PC1616, PC1832, PC1864* Not tested by UL/ULC. AlarmStateIndicatorHoldupSwitchResetToolWirelessTransmitterFigure ATo remove cover, insert screwdriver here and gently twist. Figure BTamper SwitchBATTERYExternal Contact TerminalsFigure C
FCC Compliance Statement CAUTION: Changes or modifications not expressly approved by DSC could void your authority to use thisequipment.This equipment generates and uses radio frequency energy and if not installed and used properly, in strictaccordance with the manufacturer’s instructions, may cause interference to radio and television reception. It hasbeen type tested and found to comply with the limits for Class B device in accordance with the specifications inSubpart “B” of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interfer-ence in any residential installation. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause interference to television or radio reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:• Re-orient the receiving antenna• Relocate the alarm control with respect to the receiver• Move the alarm control away from the receiver• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.If necessary, the user should consult the dealer or an experienced radio/television technician for additional sug-gestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and ResolveRadio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office,Washington, D.C. 20402, Stock # 004-000-00345-4.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.IC:160A-WS4928: The term ‘IC’ before the radio certification number only signifies that Industry Canada tech-nical specifications were met.This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including interfer-ence that may cause undesired operation of the device.Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-210. son utilisationest autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur dudispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible decompromettre le fonctionnement du dispositif.IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components iscopyrighted and is purchased under the following license terms:• This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired theSoftware and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”),the manufacturer of the integrated security systems and the developer of the software and any related products or components(“HARDWARE”) which You acquired. • If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and isNOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCTincludes computer software, and may include associated media, printed materials, and “online” or electronic documentation. • Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement islicensed to You under the terms of that license agreement. • By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally tobe bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. IfYou do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right touse it.SOFTWARE PRODUCT LICENSEThe SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual propertylaws and treaties. The SOFTWARE PRODUCT is licensed, not sold. 1. GRANT OF LICENSE This EULA grants You the following rights:(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCTinstalled. (b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or usedconcurrently on or from different computers, including a workstation, terminal or other digital electronic device (“Device”). Inother words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE willbe used.(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per licenseinstalled at any given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in thisEULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying theSOFTWARE.2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS (a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, ordisassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable lawnotwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permissionof an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institutereasonable measures to ensure compliance with the terms and conditions of this EULA.(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not beseparated for use on more than one HARDWARE unit.(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT islicensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with theHARDWARE as set forth in this EULA..(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a serveror web site.(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer ofthe HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, themedia and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If theSOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms andconditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or itssuppliers.3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to anyimages, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies ofthe SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWAREPRODUCT. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWAREPRODUCT are the property of the respective content owner and may be protected by applicable copyright or other intellectual propertylaws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved byDSC and its suppliers.4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, orentity subject to Canadian export restrictions. 5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration inaccordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall beToronto, Canada, and the language of the arbitration shall be English.7. LIMITED WARRANTY(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THESOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operatingcharacteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE orHARDWARE PRODUCTS.(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIESWARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OFTHIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THESOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THEEXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOTAPPLY TO YOU.(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY ANDALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY ORFITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NOOTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TOMODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THISSOFTWARE PRODUCT.(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANYSPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT,NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OFPROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE ORREPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES,INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that the entire system be completelytested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electri-cal disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected.© 2012 Tyco International Ltd. and its Respective Companies. All Rights Reserved. Toronto, Canada • www.dsc.com Tech Support : 1-800-387-3630 (Canada, U.S.) 905-760-3000 Printed in Canada

Navigation menu