Tyco Safety Canada 16WS90029 Wireless Security System User Manual My
Digital Security Controls Ltd. Wireless Security System My
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3075570 |
| Application ID | kfoaKgjQ0aecAKzVqvDikA== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 94.87kB (1185906 bits) |
| Date Submitted | 2016-07-25 00:00:00 |
| Date Available | 2016-07-27 00:00:00 |
| Creation Date | 2016-06-23 16:52:02 |
| Producing Software | madbuild |
| Document Lastmod | 2016-07-22 09:26:38 |
| Document Title | My Document |
| Document Author: | ncurrie |
WS900 Self-Contained Wireless Security System V1.0 User Manual WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. Read the entire manual carefully. Table of Contents 1.0 About Your Security System 1.1 Fire Detection 1.2 Carbon Monoxide Detection 1.3 Testing 1.4 Monitoring 1.5 Maintenance 2.0 General System Operation 2.1 Integrated Keypad 2.2 Panel Indicators 2.3 Important Notice 2.4 Language Selection 2.5 System Models 3.0 Arming the System 3.1 Stay Arming 3.2 Silent Exit Delay 3.3 Away Arming 3.4 Quick Exit 3.5 Arming Errors and Exit Faults 3.5.1 Arming Error 3.5.2 Audible Exit Fault 3.6 Alarm Cancel Window 3.7 Bypass Zones 3.8 Bypass Group 4.0 Disarming the System 4.1 Disarming Error 5.0 Using Wireless Keys 6.0 Emergency Keys 6.1 Two-Way Audio Operation 6.2 Intrusion (Burglary) Alarm Continuous Siren 6.3 When Alarm Sounds 6.4 Fire Alarm Pulsed Siren (Temporal 3) 6.5 Carbon Monoxide (CO) Alarm 7.0 Managing Users 7.1 Access Code Types 7.2 Level 1 Access (Supervisor/Administrator) 7.3 Level 2 Access (Basic/Standard User) 7.4 Level 3 Access (Maintenance/Guest) 8.0 Viewing Troubles on the Integrated Keypad 8.1 Alarm Memory 9.0 Testing Your System 9.1 System Test 10.0 Safety Instructions 10.1 Regular Maintenance and Troubleshooting 10.2 Cleaning and Maintenance 11.0 Locating Detectors and Escape Plan 11.1 Smoke Detectors 11.2 Fire Escape Planning 11.3 Carbon Monoxide Detectors 12.0 Installer Warning 12.0 Regulatory Agency Statements 13.0 Reference Sheets 13.1 System Information 13.2 Service Contact Information -2- 10 10 10 10 11 11 11 11 11 12 12 13 13 14 15 15 15 16 16 16 17 17 17 18 18 19 20 21 21 22 23 23 24 24 25 26 27 28 30 30 30 Chapter 1.0 About Your Security System 1.0 About Your Security System Read this manual carefully and have your installer instruct you on your system's operation and on which features have been implemented in your system. All users of this system should be fully instructed in its use. Fill out the System Information page with all of your zone information and access codes, and store this manual in a safe place for future reference. Note: The WS900 security system includes specific false alarm reduction features and is classified in accordance with ANSI/SIA CP-01-2014 Control Panel Standard - Features for False Alarm Reduction. Consult your installer for further information regarding the false alarm reduction features built into your system, as this manual does not cover all features. 1.1 Fire Detection This system can monitor fire detection devices, such as smoke detectors, and provide a warning if a fire condition is detected. Good fire detection depends on having an adequate number of detectors placed in appropriate locations. This equipment must be installed in accordance with NFPA 72 (N.F.P.A., Batterymarch Park, Quincey MA 02269). Carefully review the Family Escape Planning guidelines in this manual. Note: Your installer must enable and configure this feature. 1.2 Carbon Monoxide Detection This system can monitor carbon monoxide detectors and provide a warning if carbon monoxide is detected. Read the Family Escape Planning guidelines in this manual and the instructions for the carbon monoxide detector. Note: Your installer must enable and configure this feature. 1.3 Testing Test your system weekly to ensure that your system functions as intended. Refer to the Testing your System section in this manual. If your system does not function properly, call your installation company for service. 1.4 Monitoring This system can transmit alarms, troubles and emergency information. If you initiate an alarm by mistake, immediately call the central station to prevent an unnecessary response. Note: Your installer must enable the monitoring function before it is functional. Consult with your installer to determine if your system is configured with a communicator delay. A communicator delay prevents a report to the central station if the control panel is unset within 30-45 seconds after an intrusion alarm is triggered. Note that fire-type alarms are normally reported without a delay. Ensure that your installer verifies that your system is compatible with the Central Station Receiver format at yearly intervals. -3- Chapter 1.0 About Your Security System 1.5 Maintenance With normal use, the system requires minimum maintenance. Note the following points: Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened cloth removes normal accumulations of dust. Replace the standby battery every 3-5 years. WARNING! Do not attempt to replace the battery or open the enclosure, as there is a risk of electric shock or fire. For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion detectors, or glass break detectors, consult the manufacturerâs literature for testing and maintenance instructions. -4- Chapter 2.0 General System Operation 2.0 General System Operation Your security system comprises an integrated alarm control/panel and various sensors and detectors. The panel is mounted by the main entry/exit location. The system is self-contained; electronics and standby battery are housed within the unit. Note: Ensure that only the installer or a service professional has access to the system. The security system has several zones of area protection. Each of these zones communicates to one or more wireless sensors, such as motion detectors, glass break detectors, door contacts, etc. A sensor in alarm is indicated by messages on the WS900 mobile phone user application. Additional features include Automatic Inhibit (Swinger Shutdown) for alarm, Tamper and Trouble signals after three occurrences in a given set period, and a programmable Keypad Lockout option. For SIA CP-01 classified installations, the swinger shutdown feature is programmed such that one or two trips shuts down the zone. The zone is restored after a manual reset by entering the access code at the time of disarming the alarm system, or it is reset automatically after 48 hours with no trips on any zones. 2.1 Integrated Keypad The WS900 system includes a capacitive touch integrated keypad with 16 keys: numbers 0 thru 9, *, #, Fire, Auxiliary, Panic (FAP), and shift (up arrow). In normal operation, the keypad remains dim when not in use. When a user is in close proximity, the number keys illuminate. Note: The FAP keys do not illuminate unless the shift key is tapped. See the Emergency Keys section for more information. Note: The keypad can only be used for arming, disarming, and the local FAP. The same functions are available when switching between partitions. 2.2 Panel Indicators The WS900 system includes a series of illuminated point source status indicators. There is a minimum of seven indicators: Four single-color LEDs Three bi-color LEDs (red and green) -5- Chapter 2.0 General System Operation Item Description Power Status Light Power LED Ready to Arm LED Armed LED Trouble LED WiFi Signal Strength LED Cellular Signal Strength LED Remote Connection LED Microphone LED indicator Description ON Steady AC power is currently connected to the system. Flashing System Test All status LEDs flash at the same time. OFF This indicates the following conditions: The system is not powered ON. NO AC is connected and the system is operating on the backup battery. NO AC is connected and the backup battery is discharged.. Ready to Arm Status Light LED indicator Description ON Steady The partition is ready to arm. OFF The system is not ready to arm. Flashing System Test All status LEDs flash at the same time. Installer Walk Test Ready, Trouble, and Arm LEDs flash at the same time. -6- Chapter 2.0 General System Operation Armed Status Light LED indicator Description ON Steady The partition is armed.. Flashing The system in Alarm. Note: Silent alarms or panic do not flash the Alarm LED. System Test All status LEDs flash at the same time. Installer Walk Test Ready, Trouble, and Arm LEDs flash at the same time. Trouble Status Light OFF The partition is disarmed LED indicator Description ON Steady A system trouble is present. Flashing [cadence of 500ms On/500ms OFF] [*][2] The Trouble menu is accessed. Flashing [cadence of 250ms ON/250ms OFF/250ms ON/750ms OFF] The system is in the second-level submenu. Flashing [cadence of 250ms ON/250ms OFF/250ms ON/250ms OFF/250ms ON/750ms OFF] The system is in the third-level submenu. Flashing System Test All status LEDs flash at the same time. Flashing Installer Walk Test Ready, Trouble, and Arm LEDs flash at the same time. OFF System troubles are cleared. WiFi Signal Strength Status Light LED indicator Description ON Steady (green) The radio is active with a strong signal connection. ON Steady (yellow) The radio is active with a weak signal connection. ON Steady (red) There is no signal. ON Flashing (red). There was hardware network reset. Flashes red for several seconds, then flashes green System Test All status LEDs flash at the same time. OFF Client Mode is OFF. -7- Chapter 2.0 General System Operation Cellular Signal Strength Status Light LED indicator Description ON Steady (green) Cellular is active with a strong signal connection. ON Steady (yellow) Cellular is active with a weak signal connection. ON Steady (red) There is no signal or no connection, but a connection is expected. Flashes red for a few seconds, then flashes green System Test All status LEDs flash at the same time. Remote Connection Status Status Light LED indicator Description ON Steady (green) The link is active with Tyco On or third party server. ON Flash (red) The link activates but fails to communicate with Tyco On or third party server. OFF The link is not yet active with Tyco On or third party server.. ON Flash (green) The link is activeTyco On or third party server and Installer Access is available. Flashes red for a few seconds, then flashes green System Test All status LEDs flash at the same time. -8- Chapter 2.0 General System Operation 2.3 Important Notice A security system cannot prevent emergencies. It is only intended to alert you and your central station, if applicable, to an emergency situation. Security systems are generally very reliable, but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance. Your security system must be installed and serviced by qualified security professionals. These professionals can instruct you on the level of protection that has been provided and on system operations. Note: When the panel is in Sleep Mode, it is saving battery life. The panel will not be turned on until there is a specific reason, such as a hand wave in front of the panel, or the start of an entry delay. In this mode the keypad is still functioning and nothing will be visible; however if desired, your installer can enable the armed status to be visible while in Sleep Mode. 2.4 Language Selection The system supports the following three languages: English French Spanish You can select the language from the tablet user interface or the user app. 2.5 System Models The reference to WS900 in this manual covers the following models: WS900-29* Alarm system with two-way audio support, operating in 912-919 MHz band WS900-19* Alarm system with two-way audio support, operating in 912-919 MHz band 3G7090* 3G Cellular Alarm Communicator LT7090* Verizon LTE Only Cellular Communicator (*) These devices are UL/ULC listed. WS900-28 Alarm system operating in 868 MHz band WS901-18 Alarm system operating in 868 MHz band WS901-24EU Alarm system operating in 433 MHz band WS901-14 Alarm system operating in 433 MHz band 3G7090-EU 3G Cellular Alarm Communicator -9- Chapter 3.0 Arming the System 3.0 Arming the System You can arm the system using the following options: Integrated keypad Tablet User app Wireless key (Refer to section 5.0 for a list of UL/ULC listed compatible wireless keys.) 3.1 Stay Arming Stay Arming arms the perimeter of the premises while permitting movement inside. To arm the system in Stay mode, do the following steps: 1. Ensure all protected doors and windows are secure or bypassed and that the Ready indicator is on. 2. Enter a valid user code and do not leave the premises. The system will automatically ignore bypassed zones. Exit delay begins. 3. When exit delay is active , the Armed and Ready indicators turn on and the keypad is silent. When the exit delay has expired, the system is armed and indicated by the following conditions: The Ready indicator turns off. The Armed indicator stays on. Note: For SIA CP-01 listed panels, the Stay Arming exit delay will be twice as long as the Away Arming exit delay. If your system is installed in accordance with SIA CP-01 Standard for False Alarm Reduction, the security system arms in the Stay Armed mode if the exit delay time expires and there is no exit. 3.2 Silent Exit Delay If the system is armed in Stay mode or using the No-Entry arming method, the keypad buzzer is silenced and the exit time is doubled for that exit period only. (SIA CP-01 only.) 3.3 Away Arming Away Arming arms the entire system, including the perimeter and interior devices. To arm the system in Away mode, do the following steps: 1. Ensure all protected doors and windows are secure or bypassed and that the Ready indicator is on. 2. Enter a valid user code and exit the premises through a door programmed as entry/exit type. Exit delay begins. 3. When exit delay is active , the Armed and Ready indicators turn on and the keypad beeps once per second. Depending on your system configuration, you have ____ seconds to exit the premises. Your installer can program this time. 4. The keypad buzzer emits a distinct pulsating rate during the last 10 seconds of the exit delay to indicate that the time is expiring. 5. To cancel the arming sequence, enter your access code. - 10 - Chapter 3.0 Arming the System When the exit delay has expired, the system is armed and indicated by the following conditions: The Ready indicator turns off. The Armed indicator stays on. The keypad is silent. Note: In Away Arming mode, manually bypassed zones are logged and communicated to the central station. If your system is installed in accordance with SIA CP-01 Standard for False Alarm Reduction, the following condition applies: Violation and restoral, followed by a second violation of the entry/exit zone before the end of the exit delay, restarts the exit delay. Note: This function is available on the tablet and user app. 3.4 Quick Exit If the system is armed and you must exit, use the Quick Exit function to avoid disarming and rearming the system. Using this function gives you 2 minutes to exit the premises. When the door is closed after exiting, the remaining exit time is cancelled. 3.5 Arming Errors and Exit Faults Your security system audibly notifies you of any errors when you are attempting to arm the system or exit the premises. 3.5.1 Arming Error An error tone (long beep) sounds if the system is unable to arm. Arming errors occur under the following conditions: The system is not ready to arm, i.e. sensors are open The entered user code is incorrect. A present trouble condition. Ensure all sensors are secure and the system is ready to arm, then try again. 3.5.2 Audible Exit Fault To reduce false alarms, the Audible Exit Fault notifies you of an improper exit when arming the system. If the entry/exit door is not securely closed during the programmed exit delay, the system will sound the alarm to indicate an improper exit. Note: Your installer must enable this feature. To correct and exit fault, do the following steps: 1. Re-enter the premises. 2. Enter your access code to disarm the system before the entry delay timer expires 3. Ensure all sensors are secure and the system is ready to arm. 4. Repeat the Away arming procedure. 3.6 Alarm Cancel Window There is a period of time in which you can cancel the alarm transmission. When the programmed alarm transmission delay expires, cancelling an alarm sends a message to the central monitoring station. When the cancellation message is successfully transmitted, the system beeps six times. Note: Your installer can enable and configure this feature. - 11 - Chapter 3.0 Arming the System 3.7 Bypass Zones Use the zone bypassing feature when you need access to a protected area while the system is armed, or when a zone is temporarily out of service, but you need to arm the system. Bypassed zones are not able to sound an alarm. As a result, bypassing zones reduces the level of security. If you are bypassing a zone because it is not working, call a service technician immediately to resolve the problem an restore your system to proper working order. Ensure that no zones are unintentionally bypassed when arming your system. Zones cannot be bypassed once the system is armed. Bypassed zones, except for 24-hour zones, are automatically cancelled each time the system is disarmed and must be bypassed again before the next arming. Note: Two-hour zones can only be unbypassed manually. This function is available on the tablet and user app. For UL listed installations, zones can only be bypassed manually. 3.8 Bypass Group A bypass group is a selection of zones programmed into the system. If you bypass a group of zones on a regular basis, you can program them into a bypass group, so that you do not have to bypass each zone individually. Note that you can only program one bypass group at a time. Note: This feature is not to be used in UL Listed installations. This function is available on the tablet. For UL listed installations, zones can only be bypassed manually. - 12 - Chapter 4.0 Disarming the System 4.0 Disarming the System You can arm the system using the following options: Integrated keypad Tablet User app Wireless key (Refer to section 5.0 for a list of UL/ULC listed compatible wireless keys.) To disarm the system on the integrated keypad, do the following steps: 1. Enter your access code. 2. If you open the entry/exit door, a continuous tone indicates that entry delay has started. Enter your access code within ____ seconds to avoid an alarm condition. Your installer can program this time. 4.1 Disarming Error If your code is invalid, the system will not disarm and the system emits a 2-second error tone. If this happens, press [#] and try again. - 13 - Chapter 5.0 Using Wireless Keys 5.0 Using Wireless Keys In addition to the keypad, you can control your system with two-way wireless keys. All wireless key buttons are programmable. Your installer can verify the functions for each key. Using a two-way wireless key, you can arm or disarm the system while you are in close proximity to your house, or you can call for help. The following wireless keys are compatible with the WS900 system: PG4929/PG8929/PG9929 PG4939/PG8939/PG9939 1. 2. 3. 4. 5. 6. 7. Away Arm Stay Arm Disarm Panic Command Output 1 Message LED Status LEDs 1. 2. 3. 4. 5. 6. Away Arm Stay Arm Disarm Panic Command Output 1 LED To arm the system with a wireless key, press the desired arming mode button when the Ready indicator is on. Note: When arming the system with a two-way wireless key, the system squawks once to indicate the system is armed. To disarm the system with a two-way wireless key, do the following steps: 1. Press the disarm button. 2. If you walk through the entry door, the keypad will beep. Press the disarm button within __ __ seconds to avoid an alarm condition. Note: When disarming the system with a two-way wireless key, the system squawks twice to indicate the system is disarmed. - 14 - Chapter 6.0 Emergency Keys 6.0 Emergency Keys IMPORTANT: EMERGENCY USE ONLY! The emergency keys generate a fire, auxiliary, or panic alarm and alerts the central monitoring station. To use the emergency keys, do the following steps: 1. Tap the shift key on the keypad. The emergency keys illuminate. Fire Alarm Auxiliary Alarm Panic Alarm 2. Touch the Fire, Auxiliary, or Panic key for 2 seconds, as needed. The system beeps to indicate that the alarm input has been accepted and sent to the monitoring station. 3. To return to the number keypad without using the emergency keys, tap the [#] key. Note: Depending on your system configuration, your installer can disable any of the emergency keys. 6.1 Two-Way Audio Operation This feature is used to verify the nature of an alarm and to determine the type of assistance the occupant needs. When the central monitoring station receives an alarm, they initiate a two-way audio session. Note: Only the central monitoring station can initiate a two-way audio session when they receive an alarm.; the user cannot initiate a session. 6.2 Intrusion (Burglary) Alarm Continuous Siren If you are unsure of the source of the alarm, proceed with caution! If the alarm was accidental, enter your access code to silence the alarm. If the alarm system is disarmed within the programmed transmitter delay time, no alarm transmission is sent to the central - 15 - Chapter 6.0 Emergency Keys monitoring station. Check with your installer to see if this option has been enabled on your system and for the transmitter delay time. Following the transmitter delay time, you have 5 minutes to enter your user code to cancel an alarm that has been previously transmitted. A cancel signal is sent to the central monitoring station and the system indicates that the cancel signal was transmitted. Call your central monitoring station to avoid a dispatch. 6.3 When Alarm Sounds The system can generate the three different alarm sounds in this order of priority: 1. Fire Alarm = Temporal/pulsed siren 2. Carbon Monoxide Alarm = four beeps, 5-second pause, four beeps 3. Intrusion (Burglary) Alarm = Continuous siren Note: The Auxiliary Alarm is silent and only results in an alarm transmission to the central monitoring station. 6.4 Fire Alarm Pulsed Siren (Temporal 3) In the event of a fire alarm, follow your emergency evacuation plan immediately! The fire alarm temporal/pulsed siren sounds of three short pulses followed by a 1.5-second pause, then repeats. . If the fire alarm was accidental, e.g. burnt toast, bathroom steam, etc., enter your access code to silence the alarm and call your central monitoring station to avoid a dispatch. Note: Verify with your alarm company that your system is equipped with fire detection. For information on resetting smoke detectors see Resetting Smoke Detectors. 6.5 Carbon Monoxide (CO) Alarm WARNING! Carefully review your Carbon Monoxide Alarm Installation/User Guide to determine the necessary actions required to ensure your safety and ensure that the equipment is operating correctly. Incorporate the steps outlined in the guide into your evacuation plan. Activation of your CO alarm indicates the presence of carbon monoxide (CO), which can be fatal. An alarm is indicated by the following conditions: The red LED on the CO detector flashes rapidly and buzzer sounds with a repeating cadence of 4 quick beeps, 5-second pause, 4 quick beeps. The siren connected to the control panel produces the same cadence as above. The system provides audible and visual indication of the CO alarm. If the CO alarm sounds, do the following steps: 1. Press the button on the CO detector to silence the alarm. 2. Call emergency services or your fire department. 3. Immediately move outdoors or to an open door/window. - 16 - Chapter 7.0 Managing Users 7.0 Managing Users The WS900 system supports up to 100 users, including the Master user. By default, user #1 is the Master user. You cannot disable or delete this user from the system. The system also supports an additional two duress codes, one for each partition. From the user app, you can program and configure attributes for users 2 thru 100. You can assign a user to one or both partitions and enable or disable system interaction. User codes are 4-digits and must be unique; the system does not recognize duplicate codes. If you program a duplicate code, the system errors and the code is rejected. If you try to change an existing user code to a one that is already programmed, the system errors and the code is unchanged. 7.1 Access Code Types The WS900 system provides the following user access code types: Master Code This is the system master code. You cannot disable or delete this code, but you can change it in the user app. Use this code to program all other access codes, including the duress codes. You can use this code to do all user-level functions, except to access Installer mode. User Codes There are three access levels for user codes: Level 1 - Supervisor/Administrator Level 2 - Basic/Standard User Level 3 - Maintenance/Guest Each level has different permissions. See User Code Access Levels for descriptions of each level. Duress Codes Use duress codes to disarm the system only in an emergency situation. When used, an emergency disarm event transmits to the central monitoring station. The system supports two duress codes, one for each partition. These codes are excluded from the total number of available codes. They have the access level of a Level 2 Basic User. 7.2 Level 1 Access (Supervisor/Administrator) Users at this level have similar privileges to the master user but are limited based on their partition assignment. Users can do the following actions on their partitions: Arm/disarm Bypass/unbypass Chime enable/disable View troubles View alarm memory Level 1 users can also do any user level functionality on the keypad or user app, as follows: Initiate system test Enable installer or remote access Language selection View event buffer View images Program zone and partition labels Schedule Auto Arming - 17 - Chapter 7.0 Managing Users Initiate firmware updates Update the system WiFi SSID and password Create new users and user labels Program duress codes Note: Users can only add, edit, or delete users that are assigned to the same partition as they are. 7.3 Level 2 Access (Basic/Standard User) Users at this level have access to basic security functions but are limited based on their partition assignment. Users can do the following actions on their partitions: Arm/disarm Bypass/unbypass Chime enable/disable View system troubles View alarm memory 7.4 Level 3 Access (Maintenance/Guest) Users at this level are limited to reduced system access on their partition assignment. Users can do the following actions on their partitions: Arm/disarm Chime enable/disable View system troubles View alarm memory - 18 - Chapter 8.0 Viewing Troubles on the Integrated Keypad 8.0 Viewing Troubles on the Integrated Keypad When the system detects a trouble condition, the Trouble indicator turns on and the system beeps once every 10 seconds. Tap the [*] key to silence the beeps. Note: For UL Listed installations, your access code is required to view system troubles. To view troubles on the integrated keypad, do the following steps: 1. When the keypad illuminates, tap [*][2]. 2. Enter your access code, if required. The Trouble indicator flashes if an access code is required. The system indicates top-level trouble codes by illuminating the corresponding numbers on the keypad, and the Trouble indicator flashes once with a pause, then repeats. 3. Tap one of the numbers to see the next level code. At the second level, the Trouble indicator flashes twice with a pause, then repeats. 4. Repeat step 3 to go to the next level. The system beeps if there is no third-level trouble condition. At this level, the Trouble indicator flashes three times with a pause, then repeats. If there is more than one zone in trouble, each zone number will flash in sequence until you exit the trouble menu or when the time expires. At this level, the Trouble indicator flashes three times with a pause, then repeats. 5. Tap [#] to return to the previous level trouble code or to exit the trouble menu. Top Level Device Type Second Level Trouble Type Third Level Device ID 01 01 AC Not applicable 02 Battery Trouble 03 Tamper 04 RF Jam 01 AC 02 Battery Trouble 03 Tamper 04 Fault (supervision) 05 Not Networked 06 Fire/CO Trouble 01 AC 02 Battery Trouble 03 Tamper 04 Fault ( supervision) 05 Not Networked 01 AC 02 Battery Trouble 03 Tamper 04 Fault ( supervision) 05 Not Networked 02 03 04 System Trouble Zone Siren Keypad 1-128 1 to 16 1 to 4 - 19 - Chapter 8.0 Viewing Troubles on the Integrated Keypad Top Level Device Type Second Level Trouble Type Third Level Device ID 05 01 AC 1 to 8 02 Battery Trouble 03 Tamper 04 Fault ( supervision) 05 Not Networked 01 AC 02 Battery Trouble 03 Tamper 04 Fault ( supervision) 05 Not Networked 01 Receiver not available 02 FTC 03 Receiver supervision trouble 04 Cellular Trouble 05 Ethernet/WiFi Trouble 06 Remote shutdown 06 07 Repeater Wireless key Communication 1 to 32 Not applicable 8.1 Alarm Memory When an alarm occurs while the system is armed, it is stored in the alarm memory when you disarm the system. The system sounds a different tone than normal during entry delay. After disarming the system, the zone number on the keypad flashes for 5 minutes to indicate an alarm in memory. Note: If disarming the system with a 2-way wireless key, the system squawks three times to indicate an alarm in memory. Proceed with caution, as an intruder can still be within the premises. To arm the system again, wave your hand in front of the keypad. The zone numbers stop flashing and you can then arm the system. The alarm memory clears the next time you arm and disarm the system. - 20 - Chapter 9.0 Testing Your System 9.0 Testing Your System Inform your Monitoring Station when you begin and end system testing. Household fire alarm systems shall be tested by a qualified service technician at least every 3 years in accordance with NFPA72. It is the userâs responsibility to test the system weekly (excluding smoke detectors). Ensure you follow all the steps identified in the following sections. Should the system fail to function properly, call your installer immediately for service. 9.1 System Test The system test activates a 4-second check of the system status indicators, keypad lights, buzzer, and siren. It is a partition-based test must be done when the system is disarmed. To start a system test, do the following steps: The following conditions indicate a system test is in progress: All system status indicator lights flash for 4 seconds. A system test transmits to the central monitoring station The system checks the backup battery level. The keypad lights illuminate for 4 seconds. The system buzzer sounds for 4 seconds, or the partition buzzer and siren sound for 2 seconds each in series. - 21 - Chapter 10.0 Safety Instructions 10.0 Safety Instructions This equipment is stationary-DIRECT PLUG-IN and must be installed by Service Persons only (Service Person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons). It must be installed and used within an environment that provides the pollution degree max 2, over voltages category II, in non-hazardous, indoor locations only. WARNING! This equipment has no mains on/off switch; if the equipment must be quickly disconnected, the plug of the direct plug-in power supply is intended to serve as the disconnecting device; it is imperative that access to the mains plug and associated mains socket/outlet, is never obstructed. When using equipment connected to the mains and/or to the telecommunication network, there are basic safety instructions that shall always be followed. Refer to the safety instructions provided with this product and save them for future reference. To reduce the risk of fire, electric shock and/or injury, observe the following: Do not attempt to service this product yourself. Opening or removing the cover may expose you to dangerous voltage or other risk. Refer servicing to service persons. Never open the device yourself. Use authorized accessories only with this equipment! DO NOT leave and/or deposit ANY object on the top of the cabinet of this equipment! The cabinet as it is installed on the wall, is not designed to support any supplementary weight! Do not touch the equipment and its connected cables during an electrical storm; there may be a risk of electric shock. Never touch un-insulated wires or terminals unless the equipment has been disconnected from the mains supply and from the telecommunication network! Ensure that cables are positioned so that accidents cannot occur. Connected cables must not be subject to excessive mechanical strain. Do not spill any type of liquid on the equipment. Do not use the Alarm system to report a gas leak if the system is near a leak. These safety instructions should not prevent you from contacting the distributor and/or the manufacturer to obtain any further clarification and/or answers to your concerns. - 22 - Chapter 10.0 Safety Instructions 10.1 Regular Maintenance and Troubleshooting Keep your Alarm Controller in optimal condition by following all the instructions that are included within this manual and/or marked on the product. It is the end-user and/or installerâs responsibility to ensure that the disposal of the used batteries is made according to the waste recovery and recycling regulations applicable to the intended market. 10.2 Cleaning and Maintenance Clean the units by wiping with a damp cloth only. Do not wipe the front cover with alcohol. Do not use any water or any other liquid. Do not use abrasives, thinners, solvents or aerosol cleaners (spray polish) that may enter through holes in the Alarm Controller and cause damage. Use the system test described in âTesting Your Systemâ to check the battery condition. We recommend, however, that the standby batteries be replaced every 3-5 years. For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion detectors or glass break detectors, consult the manufacturerâs literature for testing and maintenance instructions. - 23 - Chapter 11.0 Locating Detectors and Escape Plan 11.0 Locating Detectors and Escape Plan The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke and CO alarms. 11.1 Smoke Detectors Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent. Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each sleeping area and on each storey of the home. The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke alarms. It is recommended that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that should be protected include: the basement; bedrooms, especially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not protected by the required units. On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-02 or other appropriate national standards for installation recommendations. Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may prevent the unit from detecting smoke. Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector may prevent smoke from entering the unit. Do not locate detectors in areas of high humidity. Do not locate detectors in areas where the temperature rises above 38ÂşC (100ÂşF) or falls below 5ÂşC (41ÂşF). Smoke detectors must always be installed in USA in accordance with Chapter 29 of NFPA 72, the National Fire Alarm Code: 29.5.1.1. Where required by applicable laws, codes, or standards for a specific type of occupancy, approved single- and multiple-station smoke alarms shall be installed as follows: 1. In all sleeping rooms and guest rooms. 2. Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft) of any door to a sleeping room, the distance measured along a path of travel. 3. On every level of a dwelling unit, including basements. 4. On every level of a residential board and care occupancy (small facility), including basements and excluding crawl spaces and unfinished attics. 5. In the living area(s) of a guest suite. 6. In the living area(s) of a residential board and care occupancy (small facility). Figure 1 Figure 2 - 24 - Figure 3 Chapter 11.0 Locating Detectors and Escape Plan Figure 3a Figure 4 11.2 Fire Escape Planning There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed. 1. Every family member should participate in developing the escape plan. 2. Study the possible escape routes from each location within the house. Since many fires occur at night, special attention should be given to the escape routes from sleeping quarters. 3. Escape from a bedroom must be possible without opening the interior door. Consider the following when making your escape plans: Make sure that all border doors and windows are easily opened. Ensure that they are not painted shut, and that their locking mechanisms operate smoothly. If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue should be developed. This includes making sure that those who are to perform the rescue can promptly hear the fire warning signal. If the exit is above the ground level, an approved fire ladder or rope should be provided as well as training in its use. Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in winter; outdoor furniture or equipment should not block exits. Each person should know the predetermined assembly point where everyone can be accounted for (e.g., across the street or at a neighbor's house). Once everyone is out of the building, call the fire department. A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings as this can waste valuable time. Once outside, do not re-enter the house. Wait for the fire department. Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know what to do. Revise the plan as conditions change, such as the number of people in the home, or if there are changes to the buildingâs construction. Make sure your fire warning system is operational by conducting weekly tests. If you are unsure about system operation, contact your installer. We recommend that you contact your local fire department and request further information on fire safety and escape planning. If available, have your local fire prevention officer conduct an in-house fire safety inspection. - 25 - Chapter 11.0 Locating Detectors and Escape Plan Figure 5 11.3 Carbon Monoxide Detectors Carbon monoxide is colorless, odorless, tasteless, and very toxic, it also moves freely in the air. CO detectors can measure the concentration and sound a loud alarm before a potentially harmful level is reached. The human body is most vulnerable to the effects of CO gas during sleeping hours; therefore, CO detectors should be located in or as near as possible to sleeping areas of the home. For maximum protection, a CO alarm should be located outside primary sleeping areas or on each level of your home. Figure 5 indicates the suggested locations in the home. Do NOT place the CO alarm in the following areas: Where the temperature may drop below -10ÂşC or exceed 40ÂşC Near paint thinner fumes Within 5 feet (1.5m) of open flame appliances such as furnaces, stoves and fireplaces In exhaust streams from gas engines, vents, flues or chimneys Do not place in close proximity to an automobile exhaust pipe; this will damage the detector PLEASE REFER TO THE CO DETECTOR INSTALLATION AND OPERATING INSTRUCTION SHEET FOR SAFETY INSTRUCTIONS AND EMERGENCY INFORMATION. - 26 - Chapter 12.0 Installer Warning of flammable materials, overloaded electrical circuits, children playing with matches or arson. Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. 12.0 Installer Warning Warning Please Read Carefully Note To Installers: This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. Motion Detectors Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric System Failures area protection. They have multiple beams of detection and motion can only be This system has been carefully designed to be as effective as possible. There detected in unobstructed areas covered by these beams. They cannot detect are circumstances, however, involving fire, burglary, or other types of emermotion which occurs behind walls, ceilings, floor, closed doors, glass pargencies where it may not provide protection. Any alarm system of any type may titions, glass doors or windows. Any type of tampering whether intentional or be compromised deliberately or may fail to operate as expected for a variety of unintentional such as masking, painting, or spraying of any material on the reasons. Some but not all of these reasons may be: lenses, mirrors, windows or any other part of the detection system will impair Inadequate Installation its proper operation. A security system must be installed properly in order to provide adequate proPassive infrared motion detectors operate by sensing changes in temperature. tection. Every installation should be evaluated by a security professional to However their effectiveness can be reduced when the ambient temperature rises ensure that all access points and areas are covered. Locks and latches on win- near or above body temperature or if there are intentional or unintentional dows and doors must be secure and operate as intended. Windows, doors, sources of heat in or near the detection area. Some of these heat sources could walls, ceilings and other building materials must be of sufficient strength and be heaters, radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lightconstruction to provide the level of protection expected. A reevaluation must be ing and so on. done during and after any construction activity. An evaluation by the fire and/or Warning Devices police department is highly recommended if this service is available. Warning devices such as sirens, bells, horns, or strobes may not warn people or Criminal Knowledge This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected. waken someone sleeping if there is an intervening wall or door. If warning devices are located on a different level of the residence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired person. Telephone Lines Access by Intruders If telephone lines are used to transmit alarms, they may be out of service or Intruders may enter through an unprotected access point, circumvent a sensing busy for certain periods of time. Also an intruder may cut the telephone line or device, evade detection by moving through an area of insufficient coverage, dis- defeat its operation by more sophisticated means which may be difficult to connect a warning device, or interfere with or prevent the proper operation of the detect. system. Insufficient Time Power Failure Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC power, any interruption, however brief, will render that device inoperative while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended. There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the emergency due to their inability to respond to the warnings in a timely manner. If the system is monitored, the response may not occur in time to protect the occupants or their belongings. Component Failure Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended due to the failure of a component. Inadequate Testing Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested weekly and immediately after a break-in, an attempted break-in, a This systemâs wireless transmitters have been designed to provide several fire, a storm, an earthquake, an accident, or any kind of construction activity years of battery life under normal conditions. The expected battery life is a func- inside or outside the premises. The testing should include all sensing devices, tion of the device environment, usage and type. Ambient conditions such as keypads, consoles, alarm indicating devices and any other operational devices high humidity, high or low temperatures, or large temperature fluctuations may that are part of the system. reduce the expected battery life. While each transmitting device has a low batSecurity and Insurance tery monitor which identifies when the batteries need to be replaced, this monRegardless of its capabilities, an alarm system is not a substitute for property itor may fail to operate as expected. Regular testing and maintenance will keep or life insurance. An alarm system also is not a substitute for property owners, the system in good operating condition. renters, or other occupants to act prudently to prevent or minimize the harmful Compromise of Radio Frequency (Wireless) effects of an emergency situation. Failure of Replaceable Batteries Devices Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jamming or other inadvertent radio signal interference. System Users A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is important that all system users be trained in the correct operation of the alarm system and that they know how to respond when the system indicates an alarm. Smoke Detectors Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence or building. Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage - 27 - Chapter 12.0 Regulatory Agency Statements 12.0 Regulatory Agency Statements FCC MODIFICATION STATEMENT Digital Security Controls has not approved any changes or modifications to this device by the user. Any changes or modifications could void the userâs authority to operate the equipment .Digital Security Controls nâapprouve aucune modification apportĂŠe Ă lâappareil par lâutilisateur, quelle quâen soit la nature. Tout changement ou modification peuvent annuler le droit dâutilisation de lâappareil par lâutilisateur. ISED CANADA INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules and ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prĂŠsent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisĂŠe aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioĂŠlectrique subi, ĂŞme si le brouillage est susceptible d'en compromettre le fonctionnement. FCC CLASS B DIGITAL DEVICE NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or experienced radio/television technician for help. CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numĂŠrique de classe B est conforme Ă la norme canadienne ICES-003. The reference to the WS900-xx throughout this manual is applicable to the following model numbers: WS900-19 and WS900-29. FCC ID:F5316WS90019 FCC ID:F5316WS900-29 IC: 160A-WS90019 IC: 160A-WS90029 FCC/ISED CANADA WIRELESS NOTICE This equipment complies with FCC and ISED Canada radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 m between the radiator and your body. Antenna gain must be below: Frequency band 3G4000 GSM 850 / FDD V x.xx dBi PCS 1900 / FDD II x.xx dBi LTE B4 (1700 MHz) x.xx dBi LTE B13 (700 MHz) x.xx dBi The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except as described in this user manual. Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement on contrĂ´lĂŠ. L'antenne doit ĂŞtre installĂŠ de façon Ă garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps. Gain de l'antenne doit ĂŞtre ci-dessous: Frequency band 3G4000 GSM 850 / FDD V x.xx dBi PCS 1900 / FDD II x.xx dBi LTE B4 (1700 MHz) x.xx dBi LTE B13 (700 MHz) x.xx dBi L'antenne (s) utilisĂŠe pour cet ĂŠmetteur ne doit pas ĂŞtre situĂŠ ou opĂŠrant en conjonction avec une autre antenne ou ĂŠmetteur, sauf tel que dĂŠcrit dans ce mode d'emploi. The reference to the Cellular Communicator xx7090 throughout this manual is applicable to the following model numbers: 3G7090 and LT7090. FCC ID:F53163G7090 FCC ID:F5316LT7090 IC: 160A-3G7090 IC: 160A-LT7090 WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20cm or more must be maintained between the antenna of this device and persons during device operation. FCC/IC LABEL The modular transmitter 3G7090 or LT7090 is labeled with its own FCC ID and IC number. When the module is installed inside the host device WS900-19 or WS90029 and the FCC ID/IC of the module is not visible, the host device displays the provided label referring to the FCC ID and IC of the enclosed module. This label is shipped together with the module and it is the responsibility of the integrator to apply it to the exterior of the enclosure, as displayed in the following figure. Label Placement - 28 - Chapter 12.0 Regulatory Agency Statements +HUHE\ '6& GHFODUHV WKDW WKLV GHYLFH LV LQ FRPSOLDQFH ZLWK WKH HVVHQWLDO UHTXLUHPHQWVDQGRWKHUUHOHYDQWSURYLVLRQVRI'LUHFWLYH (& 7KH FRPSOHWH 5 77( 'HFODUDWLRQ RI &RQIRUPLW\ FDQ EH IRXQG DW KWWS ZZZGVFFRPOLVWLQJVBLQGH[DVS[ &=( '6& MDNR YÂżUREFH SURKODÄŁXMH ĹH WHQWR YÂżUREHN MH Y VRXODGX VH YÄŁHPL UHOHYDQWQÂŻPLSRĹDGDYN\VPĂUQLFH (& '$1 '6&HUNO¨UHUKHUYHGDWGHQQHNRPSRQHQWHQRYHUKROGHUDOOHYLNWLJHNUDYVDPW DQGUHEHVWHPPHOVHUJLWWLGLUHNWLY (& '87 +LHUELM YHUNODDUW '6& GDW GLW WRHVWHO LQ RYHUHHQVWHPPLQJ LV PHW GH HLVHQ HQ EHSDOLQJHQYDQULFKWOLMQ (& ),1 '6&YDNXXWWDDODLWWHHQWÂŚ\WWÂŚYÂŚQGLUHNWLLYLQ (&ROHQQDLVHWYDDWLPXNVHW )5( 3DU OD SUÂŤVHQWH '6& GÂŤFODUH TXH FH GLVSRVLWLI HVW FRQIRUPH DX[ H[LJHQFHV HVVHQWLHOOHVHWDXWUHVVWLSXODWLRQVSHUWLQHQWHVGHOD'LUHFWLYH (& *(5 +LHUGXUFKHUNOÂŚUW'6&GDÂĄGLHVHV*HUÂŚWGHQHUIRUGHUOLFKHQ%HGLQJXQJHQXQG 9RUUDXVHW]XQJHQGHU5LFKWOLQLH (&HQWVSULFKW *5( ËËË˹ˏ˲ËËˎ˚˪˹ˏ˯ˤ'6&˥ˤ˨˝˪ˢˌ˚˹ˌË˲˹Ëˤ˰˲˰˧ˢ˲ËˢËËŞËˌ˰˺ˊ˳˜˪ˤˊˢ˹ˌ˯ ˏ˲˰ˌ˝˥ˤ˯ËËËËŚËąË˰ˢˌ˯˧Ëˌˊˢ˚˨ˢ˯˹ˌ˯Ë˨˨ˢ˯˰˴ˢ˹ˌ˧ËËŻËËŞË˳ˏˎË˯˹ˤ˯ËËĄË¤Ë ËËËŻ (& ,7$ &RQ OD SUHVHQWH OD 'LJLWDO 6HFXULW\ &RQWUROV GLFKLDUD FKH TXHVWR SURGRWWR ÂŞ FRQIRUPH DL UHTXLVLWL HVVHQ]LDOL HG DOWUH GLVSRVL]LRQL ULOHYDQWL UHODWLYH DOOD 'LUHWWLYD &( 125 '6&HUNO¨UHUDWGHQQHHQKHWHQHULVDPVYDUPHGGHJUXQQOHJJHQGHNUDYRJ ÂşYULJHUHOHYDQWHNUDYLGLUHNWLY () 32/ '6&RÄZLDGF]DÄžHXU]ĂG]HQLHMHVWZ]JRGQRÄFL]]DVDGQLF]\PLZ\PDJDQLDPL RUD]SR]RVWDÄ\PLVWRVRZQ\PLSRVWDQRZLHQLDPL'\UHNW\Z\ :( 325 3RUHVWHPHLRD'6&GHFODUDTXHHVWHHTXLSDPHQWRHVWÂŁHPFRQIRUPLGDGH FRP RV UHTXLVLWRV HVVHQFLDLV H RXWUDV GHWHUPLQDŠ¡HV UHOHYDQWHV GD 'LUHFWLYD (& 63$ 3RUODSUHVHQWH'6&GHFODUDTXHHVWHHTXLSRHVWÂŁHQFRQIRUPLGDGFRQORV UHTXLVLWRVHVHQFLDOHV\RWURVUHTXLVLWRVUHOHYDQWHVGHOD'LUHFWLYD (& 6:( '6&EHNUÂŚIWDUKÂŚUPHGDWWGHQQDDSSDUDWXSSI\OOHUGHYÂŚVHQWOLJDNUDYHQRFK DQGUDUHOHYDQWDEHVWÂŚPPHOVHUL'LUHNWLYHW (& - 29 - Chapter 13.0 Reference Sheets 13.0 Reference Sheets Fill out the following information for future reference and store this guide in a safe place. 13.1 System Information Mark if Buttons are Enabled [F] FIRE [M] Medical [P] PANIC The Exit Delay Time is _______ seconds. The Entry Delay Time is _______ seconds. 13.2 Service Contact Information Central Station Information Account #: ___________________ Telephone #: __________________ Installer Information: Company: ___________________ Telephone #: __________________ Battery Installation / Service Date: _____________________ _____________________ _____________________ IMPORTANT: If you suspect a false alarm signal has been sent to the central monitoring station, call the station to avoid an unnecessary response. - 30 - Š 2016 Tyco Security Products. All Rights Reserved. Tech Support: 1-800-387-3630 (Canada & U.S.) or 905-760-3000 ⢠www.dsc.com The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security Products will aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco Security Products are the property of their respective owners, and are used with permission or allowed under applicable laws. Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative. 29009783R001
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : ncurrie Create Date : 2016:06:23 16:52:02+01:00 Modify Date : 2016:07:22 09:26:38-04:00 Subject : Has XFA : No Language : en-us Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : ncurrie Description : Title : My Document Metadata Date : 2016:07:22 09:26:38-04:00 Keywords : Producer : madbuild Document ID : uuid:a28155e2-2b93-411d-912c-89f15bc7c408 Instance ID : uuid:3ac8a905-502b-40b9-8764-df41a5daa092 Page Layout : TwoColumnLeft Page Mode : UseOutlines Page Count : 31EXIF Metadata provided by EXIF.tools