Tyco Safety Sensormatic UMEXCAL Anti Theft Device User Manual

Tyco Safety Products/Sensormatic Anti Theft Device Exhibit 11 User s s

a href="https://usermanual.wiki/Tyco-Safety-Sensormatic" itemprop="url"> Tyco Safety Sensormatic >

users manual

Preliminary AMS-1070 CONTROLLER INSTALLATION GUIDE (8200-0127-06, REV. 0) 1 of 13 AMS-1070 Controller Installation Guide  ZEDEX-1070 Contents About this Guide ................................................ 1 About the Product .............................................. 2 Installation Requirements .................................. 2 Installing the Controller ...................................... 4 Connecting the Antennas and Remote Alarm Module ............................................................... 5 Connecting a tall and a short antenna ........ 5 Connecting two short antennas and a remote alarm module .............................................. 5 Connecting a split-receiver (dual-aisle) configuration................................................ 6 Connecting the Noise Canceling Antennas....... 6 Connecting to Relays in the Controller .............. 6 Connecting Power to the Controller................... 7 Connecting a Service Laptop to the Controller.. 7 Connecting a Modem to the Controller.............. 8 Connecting a Controller to an RS-485 Network 9 Connecting a Modem to an RS-485 Network.. 10 Specifications................................................... 10 Declarations..................................................... 13 Regulatory Compliance............................. 13 Other Declarations .................................... 13   © Sensormatic 2002 About this Guide This installation guide explains how to install the controller for an AMS-1070 system. This document only describes how to install the controller and connect the antenna cables. Information on how to mount the antennas is in the antenna documents. Other related documents are: •  Install Guide, AMS-1070 Antenna, P/N 8200-0127-01 •  Quick Install Guide, AMS-1070 Remote Alarm Module, P/N 8200-0127-02 •  Installation Guide, Digital 216 Noise Coils 8000-2693-05 •  Quick Install Guide, AMS-1070 Antenna Flush-Mount Brackets, P/N 8200-0127-07 •  Quick Install Guide, AMS-1070 Antenna Cantilever-Mount Brackets, P/N 8200-0127-08 •  Quick Install Guide, AMS-1070 Antenna Pole-Mount Brackets, P/N 8200-0127-09 •  Installation Guide, AMS-1070 Controller EMI Shield 8200-0127-12 •  Installation Guide, AMS-1070 Controller Under Counter Installation Guide 8200-0127-13 •  Installation Guide, AMS-1070/ScanMax Pro Deactivator Mounting Plate 8200-0127-14 Note: Because customer requirements dictate the placement of system components, your Sensormatic representative will supply this information separately.
Preliminary AMS-1070 CONTROLLER INSTALLATION GUIDE (8200-0127-06, REV. 0) 2 of 13 About the Product An AMS-1070 controller is part of an Ultra•Max® security label detector. The controller powers and controls up to four transceiver antennas, two optional remote alarm modules, and two noise canceling antenna kits. Figure 1 shows the system components. Figure 1. System components   Installation Requirements Verifying Equipment and Unpacking ❑  Verify that all equipment has arrived. Make sure the system configuration is the right one for the installation site. ❑  Unpack major components in a back room. At the install site, lay out parts in the order you will need them. Do not clutter the aisle or cause a trip hazard. Installer/Contractor ❑  Shall have electrical work comply with the latest national electrical code, national fire code, and all applicable local codes and ordinances. ❑  Shall coordinate all work with other trades to avoid interference. ❑  Shall verify existing site conditions and coordinate with the owner’s representative and appropriate utilities as required. ❑  Shall obtain copies of all related plans, specifications, shop drawings and addenda to schedule and coordinate related work. ❑  Shall thoroughly review the project to ensure that all work meets or exceeds the above requirements. Any alleged discrepancies shall be brought to the attention of Sensormatic Electronics.  !WARNING!  Do not install this product in hazardous areas where highly combustible or explosive products are stored or used.  Site Requirements Refer to Figure 2 for description of site requirements and placement considerations. ❑  Connect the controller to a 100-240Vac source. No fuse exchange is required for the controller.  ❑  Use the appropriate power cord based on the country of use. ❑  Replace the controller’s slow-blow fuses only with a fuse of the same type and rating. Tools and Equipment Required For all controller installations: •  Phillips and slotted screwdrivers •  Wire strippers •  Cordless drill and phillips-head screwdriver bits  Ranger Remote Alarm ModuleController Antenna
Download:
Mirror Download [FCC.gov]
Document ID275589
Application ID6iF5iAuy9M3CXQMR9gPQ6w==
Document Descriptionusers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize51.37kB (642106 bits)
Date Submitted2002-10-09 00:00:00
Date Available2002-10-09 00:00:00
Creation Date2002-09-25 16:39:01
Producing SoftwareAcrobat Distiller 4.05 for Windows
Document Lastmod2002-10-04 15:44:54
Document TitleExhibit 11--User's Documents
Document CreatorMicrosoft Word 9.0
Document Author: hornbeck
FCC ID Filing: BVCUMEXCAL

Navigation menu