Tyco Door Interface Unit Diu 210 Users Manual
DIU 210 to the manual 1ab7b428-5104-4748-bcae-e87504453c7f
2015-02-03
: Tyco Tyco-Door-Interface-Unit-Diu-210-Users-Manual-460835 tyco-door-interface-unit-diu-210-users-manual-460835 tyco pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
DIU 210 Door Interface Unit FEATURES OVERVIEW • Door Interface Electronics held on one board The Door Interface Unit (DIU 210) is designed primarily to provide power to a door lock, as well as local power to a CEM reader when a high level of security is required. It has onboard inputs which can be used to monitor conditions such as a fire alarm or activated Break-glass condition. The DIU 210 improves door security, by allowing the installer to locate lock controls on the secure side of a door, with an intelligent CEM reader on the unsecured side. The DIU 210 communicates with an intelligent CEM reader over a single pair RS485 cable. Upon a valid swipe at the card reader, the reader will instruct the DIU (over the RS485 communications channel) to activate the appropriate output to release the lock using a coded data signal (i.e. coded lock). As an added benefit, the DIU 210 monitors the status of all standard door monitoring inputs; inputs on an intelligent CEM reader are free for use as general purpose inputs The DIU 210 is supplied in a steel enclosure complete with power supply backplane and an output for an additional door holder. • Provides ‘coded lock’ serial interface between door hardware and card reader • On site selectable for 12V or 24V lock output • Fire alarm and break glass inputs for emergency door release • Designed for ease of installation and maintenance using 2 part connectors throughout • Compliant with EN55022 (emissions) and EN55024 (access control immunity) • Backup battery connection for emergency power DIU 210 www.cemsys.com 1. 2. 3. 4. 5. 6. 7. 8. 9. DIU Unit Enclosure CEM Reader Sounder Break Glass Unit REX/ Exit Reader or Secure side push button Door Holder Door Lock Lock Sense Door Position sensor CEM/B/045 Product Highlights Interfaces The DIU 210 provides direct interfaces to the following devices: • • • • • • can be sent directly to the door controller or to the host, via the card reader, for central alarm notification. Board Protection The DIU 210 has been designed to meet the UL294 standard providing resistance to power supply tamper, limiting the current to a reader so that shorting together the 12 Volt terminals prevents the lock from opening. CEM Card Reader Electric Door Lock Fire Alarm System Break Glass Unit Exit Push Button Inputs from alarm devices Reader Inputs The DIU 210 can also monitor the status of all the door furniture inputs, freeing up the inputs on the intelligent CEM reader for general purpose input monitoring. Up to 8 inputs can be wired from alarm/status monitoring devices directly to the DIU 210. These devices are used to monitor door sensors, DIU tamper and battery alarms and fire/ break glass emergency conditions. If an input from the fire alarm system or break glass unit changes state, the power to the door lock is automatically dropped; this hardware-controlled facility ensures that the door opens in an emergency situation. Details of alarm conditions PSU Backplane Board and Enclosure The DIU 210 is supplied with a steel enclosure and backplane board providing a mains input PSU, battery charging capabilities and door holder connections. TECHNICAL SPECIFICATIONS Physical Size 300 x 250 x 150 mm (11.8 x 9.84 x 5.9in) Weight Power - Voltage 4.3Kg 100-240VAC, 50/60Hz Current 0.6A (excluding locks and heads) Consumption Environmental - Temperature - Humidity -10º to 40ºC (14º to 104ºF) 95% non condensing LED Indicators +12 Volts OK, Lock supply OK, Lock Status, Watchdog, Fault, Battery Low, RS485 Rx and TX. Functionality Inputs * Door Position * Lock Status * Exit Push Button * General Purpose Break Glass Sense Fire Alarm Sense Power Fail Tamper Battery Low (reported internally) Dedicated Power Fail Input * = 4 state tamper protected inputs Outputs Three 12V or 24V open collector outputs limited to 1.5A (Door Lock, Door Holder and External Sounder) Reader Output 12V, limited to 800mA Memory 32kB Flash memory Communication Interface To Card Reader - Connection RS485 multidrop cable runs using copper wire with maximum length of 1.2km without repeater 2 part screw terminals Product Codes DIU/700/000 DIU 210 (Complete with PSU Backplane and Enclosure. Product specifications and availability is subject to change without notice. Certain product names mentioned herein may be trade names and/or registered trademarks of their companies. CEM Systems Ltd Unit 4 Ravenhill Business Park Ravenhill Road Belfast BT6 8AW Northern Ireland Tel: +44 (0)28 9045 6767 Fax: +44 (0)28 9045 4535 email: cem.sales@tycoint.com www.cemsys.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c006 1.236519, Wed Jun 14 2006 08:31:24 Instance ID : uuid:0d72330b-cf91-2048-937d-48cab72cb0f9 Document ID : adobe:docid:indd:237734ba-5938-11db-9784-be49e74b1a5a Rendition Class : proof:pdf Derived From Instance ID : 93b33b04-55ec-11db-9862-ca4e1a52b407 Derived From Document ID : adobe:docid:indd:41eb4a81-55e9-11db-9862-ca4e1a52b407 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 600.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 600.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:2373AE0A09D611DB80B8E236F2BC9E68, uuid:3C2E4FD15C3D11DBB4F2FBB55DF3D2F8, uuid:CFD1C23836BD11DC9459E4717F92A223, uuid:2373AE0A09D611DB80B8E236F2BC9E68 Manifest Reference Document ID : uuid:2373AE0909D611DB80B8E236F2BC9E68, uuid:3C2E4FD05C3D11DBB4F2FBB55DF3D2F8, uuid:B9E646A036B911DC9459E4717F92A223, uuid:2373AE0909D611DB80B8E236F2BC9E68 Create Date : 2008:06:03 11:58:46+01:00 Modify Date : 2008:06:03 11:58:47+01:00 Metadata Date : 2008:06:03 11:58:47+01:00 Creator Tool : Adobe InDesign CS3 (5.0.2) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 10250 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CS3 (5.0.2)EXIF Metadata provided by EXIF.tools