U S Telemetry USTC-TED-002I RTU Meter Telemetry Device User Manual 00 0589 internal

Download:
Mirror Download [FCC.gov]
Document ID	140600
Application ID	VRpot3YYweuzaAq4/OuL2Q==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.02kB (12754 bits)
Date Submitted	2001-03-16 00:00:00
Date Available	2001-03-08 00:00:00
Creation Date	2001-03-05 15:53:03
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	00-0589-internal.PDF
Document Creator	Microsoft Word
Document Author:	Workstation

FCC ID: OZ9USTC-TED-0002I
SECTION 7
USER'S MANUAL
FCC ID: OZ9USTC-TED-0002I
Axonn Corporation
U.S. Telemetry
Transmit Endpoint Device
Users Manual
RF Transmitter Installation Instructions
The USTC TED transmitter should only be installed by qualified service personnel.
The transmitter detects status or other data signals from the external binary inputs and low
battery and broadcasts that data to the system's CTS sites.
MOUNTING LOCATION
The USTC TED Transmitter is an RTU as defined by the FCC.
INSTALLATION INSTRUCTIONS
1. Supply the transmitter with DC power by inserting three 3-Volt batteries into the battery
holder inside the transmitter.
2. The unit will come pre-programmed with Transmitter ID. There will be field programming
of the unit for other parameters.
3. As the TED will be used to transmit utility-meter information to the CTS, the TED will be
located next to electric, water, or gas meters.
4. When installing the TED you should avoid areas near screens, metal window frames,
circuit breaker boxes, air conditioners and heaters if a suitable location for the unit may be
found elsewhere.
TESTING THE TRANSMITTER
Following system installation, system testing is mandatory. This should be performed by
locating the TED in its final location and powering up the unit. On initial power-up, the TED
will send out RF messages every 4 seconds or more depending on programming. This will
establish communications with the CTS receiver and the information collected will then be
used to judge system performance
FCC NOTICE
The USTC TED transmitter generates and uses radio frequency energy. If not installed and
used in accordance with the manufacturer's instructions, it may cause interference to radio
and television reception. The transmitter has been tested and found to comply with the
specifications in Part 95 of the FCC Rules.
If this equipment causes interference to radio or television reception - which can be
determined by turning the equipment on and off - the installer is encouraged to correct the
interference by one or more of the following measures: 1) Reorient the antenna of the
radio/television. 2) Connect the AC transformer to a different outlet so the TED and
radio/television are on different branch circuits. 3) Relocate the TED with respect to the
radio/television.
FCC ID: OZ9USTC-TED-0002I
If necessary, the installer should consult an experienced radio/television technician for
additional suggestions, or send for the "Interference Handbook" prepared by the Federal
Communications Commission. This booklet is available from the U.S. Government Printing
Office, Washington, D.C., 20402, stock number 004-000-00450-7.
CAUTION: Axonn Corporation does not support field changes or modifications to any of the
Axonn Corporation RF equipment unless they are specifically covered in this manual. All
adjustments must be made at the factory under the specific guidelines set forth in our
manufacturing processes. Any modification to the equipment could void the user's
authority to operate the equipment and render the equipment in violation of FCC Part 95.
This device complies with Part 95 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
CAUTION:
This device is required to comply with FCC RF exposure requirements for mobile transmitting
devices. A separation of 20 cm (8 inches) or more must be maintained between the
antenna and all persons during device operations to satisfy RF exposure compliance.
LIMITED WARRANTY
THERE ARE NOT WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no case shall Seller be liable to anyone for any consequential or incidental damages
for breach of this or any other warranty, express or implied, or upon any other basis of liability
whatsoever, even if the loss or damage is caused by Seller's own negligence or fault.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 3
Creator                         : Microsoft Word
Create Date                     : 2001:03:05 15:53:03
Title                           : 00-0589-internal.PDF
Author                          : Workstation
Producer                        : Acrobat PDFWriter 4.0 for Windows

EXIF Metadata provided by EXIF.tools