UNION COMMUNITY AC-2100PLUS Access controller User Manual VIRDI Safe 100 200 Manual

UNION COMMUNITY Access controller VIRDI Safe 100 200 Manual

User Manual

Copyright 2000 By Union Community Co., LTD.   AC-2100 Plus. USER GUIDE  Version ENG-1.00
AC-2100 Plus  사용자 가이드                                                               2 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   <Revison History>    Version Date Description Firmware Version 1.00 2016-12-28 -Initial Release 10.61.00-000.00
AC-2100 Plus  사용자 가이드                                                               3 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   <Glossaries>   Administrator (Admin) - The  administrator  can  access  to  the  terminal  menu  mode.  He/she  has  the  authority  to add/modify/delete  terminal  users  and  to  change  the  operating  environment  by  changing settings. - If there is no registered administrator in the terminal, anybody can access to the terminal menu and  change  settings.  It  is  recommended  that  more  than  one  administrator  will  be necessarily registered in the terminal. - The administrator has the authority to change critical environmental settings of the fingerprint reader. So, special attention is required to its registration and operation.   1:1 Authentication (One-to-one, Verification) - The user fingerprint is verified after entering User ID or Card. - Only User ID or the user fingerprint registered to the card is compared. This is called One-to-One Authentication.   1:N Authentication (One-to-many, Identification) - The user is identified only by the fingerprint. - The same fingerprint as the input fingerprint is identified among the registered fingerprints without User ID or Card entered. This is called One-to-N Identification.   Authentication Level - As a level used for fingerprint authentication, it is displayed in Step 1 to 9. Authentication cannot be allowed before the degree of match between two fingerprints is higher than the set authorization level. - The higher authentication level may ensure the higher security. But it requires the relatively high concordance rate. So it high likely to deny authentication when trying to authenticate. - 1:1 Level: Authentication level used for One-to-one authentication - 1:N Level: Authentication level used for One-to-N authentication   Authentication Method - This  refers  to  various  types  of  authentication  methods  composed  of  each  combination  of FP(Fingerprint) and RF(Card) and so forth. Ex) Card or FP: Authenticated by either card or fingerprint   Function Key - This refers to [F1], [F2], [F3], and [F4] keys, which enable users to access the menu or change the mode such as Attend or Leave.
AC-2100 Plus  사용자 가이드                                                               4 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Table of Contents <Revison History> .................................................................................................... 2 <Glossaries> ............................................................................................................... 3 Table of Contents ........................................................................................................ 4 1. Before Getting Started ............................................................................................. 6 1.1. Safety Notes .................................................................................................... 6 1.2. Product Details ............................................................................................... 7 1.3. Buttons displayed during operation ................................................................. 8 1.4. ViRDI logo LED signals displayed during operation ........................................ 8 1.5. Screens displayed during operation ................................................................. 8 1.5.1. Icon Information ...................................................................................... 9 1.5.2. Message Information ................................................................................ 9 1.6. Voice guide announced during operation ....................................................... 13 1.7. Buzzer guide announced during operation ..................................................... 13 1.8. How to register and enter correct fingerprint ................................................ 13 2. Product Description ............................................................................................... 15 2.1. Product Features........................................................................................... 15 2.2. Configuration Diagram ................................................................................. 17 2.2.1. Standalone Use (Access) ......................................................................... 17 2.2.2. Connecting the PC server (Access, T&A, Food Service Control) ................ 17 2.3. Product Specification .................................................................................... 18 3. Environment Setting .............................................................................................. 19 3.1. Checkpoints before environment setting ........................................................ 19 3.1.1. Enter the menu ...................................................................................... 19 3.1.2. Modify settings ...................................................................................... 20 3.1.3. Save after completion of environment setting ............................................ 20 3.2. Menu Configuration ..................................................................................... 21 3.3. User Management ......................................................................................... 25 3.3.1. Add User ............................................................................................... 25 3.3.2. Delete User ........................................................................................... 28 3.3.3. Modify User .......................................................................................... 29 3.3.4. Add Administrator .................................................................................. 32 3.3.5. Delete All Users ..................................................................................... 32 3.4. Network Setting ............................................................................................ 33 3.4.1. Terminal ID ........................................................................................... 33 3.4.2. IP Setting .............................................................................................. 35 3.4.3. Server IP Setting .................................................................................... 36 3.5. Option Setting ............................................................................................... 40 3.5.1. Application Setting ................................................................................. 40 3.5.2. Authentication Method Setting ................................................................ 45 3.5.3. Door Setting .......................................................................................... 49 3.5.4. Volume Setting ...................................................................................... 50 3.5.6. Current Time Setting .............................................................................. 51 3.5.7. RS485 Set ............................................................................................. 53 3.6. Terminal Information Inquiry ....................................................................... 54 3.7. Additional Function (Extra Function) ............................................................ 55 3.7.1. Terminal Lock Setting ............................................................................ 56
AC-2100 Plus  사용자 가이드                                                               5 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 3.7.2. Card Number Inquiry ............................................................................. 56 3.7.3. Monitor Input Port Setting ...................................................................... 57 3.7.4. Duress FP Setting ................................................................................... 58 3.8. Device Setting ............................................................................................... 59 3.8.1. System Configuration ............................................................................. 59 3.8.2. Card Reader Format Setting .................................................................... 60 3.8.3. Fingerprint Sensor Setting ....................................................................... 60 3.8.4. Wiegand Speaker Output ........................................................................ 62 3.8.5. Terminal Initialization ............................................................................ 64 3.8.6. External Device Setting .......................................................................... 66 4. How to Use Terminal ............................................................................................. 69 4.1. When operating to [1.Access] ........................................................................ 69 4.1.1. Authentication Mode .............................................................................. 69 4.1.2. Authentication Using Fingerprint ............................................................. 69 4.1.3. Authentication Using Card ...................................................................... 70 4.2. When operating to [2.T&A] .......................................................................... 72 4.2.1. Authentication Mode .............................................................................. 72 4.2.2. Fingerprint Authentication ...................................................................... 72 4.2.3. Authentication Using Card ...................................................................... 72 4.3. When operating to [2.Cafeteria] .................................................................... 72
AC-2100 Plus  사용자 가이드                                                               6 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   1. Before Getting Started  1.1. Safety Notes   Warning Do not operate the terminal with wet hands, and pay attention not to let any liquid such as water enter inside the terminal. →  Otherwise, malfunction or electric shock may be caused.  Keep the terminal away from inflammables. → Otherwise, it may cause a fire.  Do not disassemble, repair or remodel the terminal at your disposal. → Otherwise, it may cause malfunction, electric shock, or a fire.  Do not allow children to touch the terminal carelessly. → Otherwise, it may cause safety accidents of children or malfunction.  - Non-compliance of safety notes may cause death or serious injury for users.  Cautions Do not install the terminal in a place exposed to direct sunlight. → Otherwise, it may cause malfunction, deformation and discoloration.  Do not install the terminal in humid or dusty places. → Otherwise, it may cause malfunction.  Do not clean this terminal by sprinkling water, nor wipe it with benzene, thinner, and alcohol. → Otherwise, it may cause electric shock or a fire.  Keep the terminal away from magnets. → Otherwise, it may cause failure and malfunction.  Keep the fingerprint input section clean. → Otherwise, the fingerprint cannot be recognized correctly.  Do not spray insecticides or inflammables on the terminal. → Otherwise, it may cause deformation and discoloration.  Keep the terminal away from shock or sharp objects. → Otherwise, it may damage the terminal and result in malfunction.  Do not install the terminal in a place where there is a severe change in temperature. → Otherwise, it may cause malfunction.  - Non-compliance of safety notes may cause personal injury or property damage for users.  ※  We are not responsible for any accidents and damage that may arise from non-compliance of the information in this manual.
AC-2100 Plus  사용자 가이드                                                               7 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 1.2. Product Details  1.77inch TFT LCD (128*160) Touch Key Status LED FP Sensor Smart Card
AC-2100 Plus  사용자 가이드                                                               8 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  1.3. Buttons displayed during operation  F1 - Switch to ‘Attend’ mode from the default screen. - Used to move up or increase [↑] in the menu mode F2 - Switch to ‘Leave’ mode from the default screen. - Used to move down or decrease [↓] in the menu mode. F3 - Switch to ‘Outdoor’ mode from the default screen. - When pressing for more than 2 seconds, you enter the menu mode: [F3~] - Used to escape [ESC] or move left [] in the menu mode. When pressing for more than two seconds, this is used to [ESC] button: [ESC~] F4 - Switch to ‘Return’ mode from the default screen. Pressing it again in the ‘Return’ mode is changed to ‘Access’ mode. - Used to enter [ENT] or move right [] in the menu mode. When pressing for more than two seconds, this is used to [ENT] button: [F4~]  1.4. ViRDI logo LED signals displayed during operation  ViRDI Power Blue On: Normal Flickering: Under Bluetooth communication ViRDI Door Green On: Door Open Off: Door Close ViRDI Alarm Red Off: Normal Flickering: Case Open or Lock Controller Communication Error  ※  The LED may light on simultaneously in some cases. (Ex. Red and Blue flicker)  1.5. Screens displayed during operation      Displays the current time - When access control: Displays access  mode (F1, F2, F3, F4, Access) - When T&A control: Displays Attend/Leave mode (Attend, Leave, Outdoor, Return) - When food service control: Displays the menu and current meal time countdown Displays Status icon and Access mode
AC-2100 Plus  사용자 가이드                                                               9 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  1.5.1. Icon Information  ① Fire Detection  A fire is detected by the fire detection sensor. ② Door Status  Doors open state (forced open door or open the door when leaving). ③ Server Connection Status    The LAN cable is not connected.  Only Link is connected. ④ USB Connection    The USB is connected.   1.5.2. Message Information   - The default screen of AC2100  - The fingerprint is being input or on standby.  - When authentication is successful
AC-2100 Plus  사용자 가이드                                                               10 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  - When authentication fails  - When fingerprint input fails - If your finger is released too early before your fingerprint is entered  - When an unregistered card is swiped - When 1:N Authentication is attempted under the condition that authentication priority is SN and there is no user who has been allowed for 1:N Authentication  - When anti-passback is in error  - When the server cannot handle too many authentication requests from the terminal
AC-2100 Plus  사용자 가이드                                                               11 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  - When the terminal is set to the food service control and users attempt more than two times authentication in the same food time zone  - When there is no response from the server during authentication attempt - When the network is disconnected during authentication attempt to the server  - The card input is on standby.  - When the card is registered but its authentication is not attempted in the access control time  - When the terminal waits for a response after requesting authentication to the server,
AC-2100 Plus  사용자 가이드                                                               12 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  - When the terminal is locked - When the food service control is set in the non-meal time  - When the terminal program is upgraded (Do not power off the terminal when this message is displayed.)
AC-2100 Plus  사용자 가이드                                                               13 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   1.6. Voice guide announced during operation  Item Voice Guide When the fingerprint is entered Please enter your fingerprint. When authentication is successful You are authorized. When authentication fails Please try again.   1.7. Buzzer guide announced during operation  Ppik When button or card is operated - If the button is pressed or if the terminal reads the card - If your finger may be released because your fingerprint has been successfully entered Ppibik When failure If authentication fails or the user’s input is wrong Ppiriririk When input standby When it is notified that fingerprint input is on standby Ppiririk When success If authentication is successful or if the current user finishes settings   1.8. How to register and enter correct fingerprint   Correct fingerprint input method  Enter your fingerprint as if you take a thumbprint by using your forefinger if possible.   The fingerprint cannot be correctly registered and entered only by your fingertips. The center of the fingerprint should be touched with the fingerprint input section.     Enter the fingerprint of your forefinger if possible.  When using your forefinger, you can enter your fingerprint correctly and safely.   Make sure that the fingerprint is unclear or wounded.  Too  dry,  wet,  blurry  or  wounded  fingerprints  are  difficult  to  recognize.  In  this  case,  the fingerprint of another finger should be registered.
AC-2100 Plus  사용자 가이드                                                               14 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr      Precautions subject to your fingerprint status  The availability of the fingerprint may vary subject to your fingerprint status.  This  product  consists  of  a  fingerprint  recognition  system  and  cannot  recognize  the damaged or unclear fingerprints. They should be registered using a password.   If your hands are dry, you can blow your breath on the system to operate it more smoothly.   For  children,  too  small  or unclear  fingerprints  may  be  difficult  or  impossible to  use. They need to register a new fingerprint every six months.   For seniors, the fingerprint with too many lines may not be registered.   It is recommended that you will register more than two fingerprints if possible.   In order to increase the fingerprint authentication rate, it is recommended to use six of the ten fingers as illustrated above. (Both thumbs, forefingers, middle fingers)
AC-2100 Plus  사용자 가이드                                                               15 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  2. Product Description   2.1. Product Features   Access control system using the network (LAN) - The fingerprint reader communicates with the authentication server using a UTP cable and TCP/IP protocol. This terminal can be applied to the existing LAN network and has easy expandability.  It  ensures  a  fast  speed  by  10/100  Mbps  Auto  Detect  and  facilitates management and monitoring via the network.   Convenient Auto Sensing function - The  authentication  function  can be  simply  operated  by entering the  fingerprint  without separate keys entered.   Easy to verify your ID via fingerprint - The use of the fingerprint recognition technology (Biometrics) can prevent forgetting your password, losing your card or  key,  or avoid the risk of  their theft. The use of personal fingerprints enhances the security of authentication.   Convenient information message using LCD and voice - The information message is voiced or displayed on the LCD display for each operation to receive  certification  so  that  you  can  easily  input.  In  particular,  thanks  to  a  built-in backlight for the LCD display, you can easily identify the screen and operate keys in the dark room. The voice is stored in the memory and it can be changed to a desired voice from the server.   Diverse and flexible access control function - Easy to use it without the risk of rental, counterfeit and loss of your key or card; - Provide the  complete access  control function  by granting  access authority according  to user groups; - Provide the flexibility of access control by allowing the access time restrictedly; - Economical maintenance and development costs compared to other access control devices; - Remove the inconvenience that visitors are registered in the management office and then separate cards are issued.   Diverse utilization for operating systems such as security, access, T&A, and food service - Various operating methods can be supported depending on how the terminal menu is set.   Large processing capacity of server - When  the  entrant  information  is  managed  using the  server,  it  can  be  processed  almost infinitely.   Provide the Printer Interlock function   - Provide the output function for the authentication information through the printer at every time you authenticate.
AC-2100 Plus  사용자 가이드                                                               16 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   Various registration and authentication methods There are a total of four registration and authentication methods for general users. Before registering users or administrators, you should determine how to register and authenticate.  FP Fingerprint Registration Fingerprint Authentication Card Card Registration Card Authentication Card or FP Card or Fingerprint Registration Card or Fingerprint Registration Card and FP Card and Fingerprint Registration Card Authentication and then Fingerprint Authentication
AC-2100 Plus  사용자 가이드                                                               17 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  2.2. Configuration Diagram  2.2.1. Standalone Use (Access)             2.2.2. Connecting the PC server (Access, T&A, Food Service Control)                   DC12V Adapter 전기정 (Lock+, Lock-, Monitor) TCP/IP     Internet / WAN / LAN TCP/IP  TCP/IP TCP/IP TCP/IP TCP/IP Food Service Control Program   Attendance Control Program Fingerprint Authentication Server (Static IP) UDB Sever Database (MDB or MSSQL) Remote Administrator Program (User and Terminal Setting Management)
AC-2100 Plus  사용자 가이드                                                               18 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  2.3. Product Specification  구  분 SPEC REMARK CPU 32 bits RISC CPU(400MHz)  MEMORY 64M SDRAM  32M NOR FLASH 128M NAND FLASH 1,500 User 1,500 Finger 10,000 Log Fingerprint Sensor Optical  Authentication Speed Less than 1 second  Scan Area / Resolution 12.6 * 14.8mm / 500 DPI  FRR / FAR 0.1% / 0.0001%  Communication Port TCP/IP Authentication Server Communication RS-232 Printer RS-485 External Device Communication Wiegand In/Out Card Reader or External Device Communication Temperature / Humidity -20 ~ 60 / Lower than 90% RH  LCD 1.77’’ Color LCD  SIZE 58mm(W) * 191mm(H) * 62mm(D)  AC / DC Adapter INPUT : Universal AC 100 ~ 250V  OUTPUT : DC 12V   (Option : DC 24V)  UL, CSA, CE Approved  Card Reader Smart Card Reader 14443A type, 13.56MHz
AC-2100 Plus  사용자 가이드                                                               19 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3. Environment Setting  3.1. Checkpoints before environment setting  3.1.1. Enter the menu  When pressing [F3] button  for more than 2 seconds, the  administrator  authentication screen will be displayed.    The  administrator  is  verified  by  either  card  or  fingerprint  depending  on  the  authentication method. Upon successful authentication, the screen goes to the following menu.    Select the menu you want to change using [↑](F1) and [↓](F2) buttons, and press [ENT] (F4) button to go to the submenu.       The description of function buttons such as F1, F2, F3, and F4 is  in numerical order on the bottom of the screen as shown above. Go up and down the screen, you can press [ENT](F4) button to select the desired menu, or press [ESC] (F3) for more than 2 seconds to return to the upper menu.
AC-2100 Plus  사용자 가이드                                                               20 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  ※ The administrator authentication menus is displayed only when there is any registered administrator.  Once  it  is  authenticated  to  enter  the  menu  mode,  you  can  access  to  all menus until you escape completely from the main menu.   3.1.2. Modify settings  Modify the existing settings by pressing [↑][↓] buttons. If the set value is greater than or equal to 2 digits, press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the value up or down.  Press [ENT] button to check the set value or go to next setting. If you want to cancel during the setting and move to the upper menu, press [ESC] button for more than 2 seconds.  If only [←][↑][↓][→] buttons are displayed except [ESC] and [ENT] buttons, [ESC] is enabled by pressing [F3] for more than 2 seconds, and [ENT] by pressing [F4] for more than 2 seconds.  3.1.3. Save after completion of environment setting  After changing settings, press [ESC] button on the main menu screen to save the changes, and the following screen will be displayed.    Select [Yes] button to save modifications, [No] button to cancel modifications, and then press [ENT] button. If there is any modified information, the terminal will be rebooted.   If  there  is  no  change  information,  the  screen  exits  from  the  environment  setting  menu without the “Save?” process.   If no data is input in the main menu for a certain time during changing environment setting, the screen will exit from the environment setting menu. In this case, if there is any change in the menu, the screen performs the “Save?” process. If there is no change in the menu, the screen goes to the main screen without saving changes.
AC-2100 Plus  사용자 가이드                                                               21 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.2. Menu Configuration  1. User 1. Add User 2. Delete 3. Modify 4. Add admin 5. Delete All 2. Network 1. Terminal ID <Terminal ID> <Auth Mode>:NS/SN/NO/SO 2. Terminal Net <Net Type> <Terminal IP> <Subnet Mask> <Gateway> 3. Server Net <Server Type> <Server IP> <Server Port> 3. Option 1. Application <WorkMode> 1. Access 2. T&A 3. Cafeteria When setting to Access <F1 Time> <F2 Time> <F3 Time> <F4 Time> <Access Time> <Multi Fn-Key> <Use Printer> When setting to T&A < Attend> <Leave > < Out> < In> <Access Time> <Multi Fn-Key> <Use Printer> When setting to Cafeteria <Breakfast> <Lunch> <Dinner> <Supper> <Snack> <No Limit> <Use Printer>
AC-2100 Plus  사용자 가이드                                                               22 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 2. Verify <Show User> <Only Card> <Use TOC> <Blocking Time> <Global Block> <NetErr TimeOut> 3. Doorlock <Open Duration> <Open Alarm> 4. Sound <Voice> <Beep> <Case Open> 5. Time <Sync Time> <Calendar> <System Time> <Time Display> 6. RS485 Set <RS485 ID>
AC-2100 Plus  사용자 가이드                                                               23 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 4. Terminal Info   Version Firmware version of the terminal WorkMode Terminal operating modes (T&A + security/T&A/food service) Language Language setting Auth Mode Authentication priority 1:1 Level Authentication level applied when 1:1 authentication 1:N Level Authentication level applied when 1:N authentication Terminal Id Terminal ID Net Type Network connection methods (Static IP/DHCP) Terminal IP Terminal IP address Gateway Terminal gateway address Subnet Mask Terminal subnet mask address Server Type Network server connection mode setting Server IP IP address of the network server connected to the terminal Server Port Port number of the network server program MAC Address Terminal MAC address Card Ver Card reader module firmware version Card Format Card data display format All User The total number of users registered in the terminal, including administrators All Admin The number of administrators registered in the terminal Max User The maximum number of users who can be registered in the terminal All FP The total number of fingerprints saved in the terminal Max FP The maximum number of fingerprints that can be registered in the terminal All Log The number of the authentication results saved in the terminal Max Log The maximum number of the authentication results that can be saved in the terminal Serial Num Serial number notation
AC-2100 Plus  사용자 가이드                                                               24 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 5. Ext Function 1. Lock Term <Lock Term> 2. Read Card <Read Card> 3. Monitor <Monitor 1> <Monitor 2> 4. Duress FP <Duress FP> 6. Device 1. Sys Config <ID Length> <Language> 2. Card Format <Card Reader> <Card Format> 3. FP-Sensor <1:1 Level> <1:n Level> <LFD Level> <Check FP> 4. Wiegand <Wiegand Out> 5. Initialize <Init Config> <Delete Log> <Init Terminal> <DB Backup> 6.Ext Device <External Device> <Local AntiPB> <Auth Mode> <Lock Ctrl>
AC-2100 Plus  사용자 가이드                                                               25 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.3. User Management  Select [1.User] on the main menu, and the following screen will appear.    Press  [↑][↓] buttons  to  select the  menu  you  want to change, and press [ENT] button.   3.3.1. Add User  Select [F3~]→[1.User]→[1.Add User] on the main screen, and the following screen will appear.     Enter the ID of the new user you wish to register, and press [F4] button long.   When registering, the available user ID is automatically displayed on the LCD so that you can register it conveniently. If necessary, you can change the ID using function keys. If other user has been already registered in the entered ID, the message of “Duplicated User ID” with “Fail” buzzer is displayed on the LCD and then the screen goes to the upper menu. If the entered ID is not registered, the following authentication type selection screen appears.    By  using  [↑][↓]  buttons,  select  the  authentication method and “And” or “Or”, and press “Next” button.
AC-2100 Plus  사용자 가이드                                                               26 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.3.1.1. Register as “1. FP”  Register and authenticate using the fingerprint.    Default Setting: ‘0’  This screen is available to determine the authentication level for each user to be registered. By changing this value, the different authentication level may be set for each registered user. If this value is  set to ‘0’, the 1:1 Level set  in  the terminal  is  used instead of the user-specific authentication level.  After completion of setting, press the [ENT] button to move to the next setting.    Enter your fingerprint referring to “1.8. How to register and enter the fingerprint” as aforesaid.  When the fingerprint sensor lights on, place your finger on the fingerprint input window. When “Ppik” buzzer occurs, wait for about 2~3 seconds until the light turns off, and lift your finger. When the first fingerprint is successfully entered, the message of “Please try again” is displayed. Enter the fingerprint entered just now once again.    Enter the fingerprint entered just now once again.
AC-2100 Plus  사용자 가이드                                                               27 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  It should be noted that when entering the second fingerprint after entering the first fingerprint, you  must  release  your  finger  from  the  fingerprint  input  window  and  then  enter  the  second fingerprint again.  When the  registration is  completed,  select  “Add  FP”.  If  it  fails,  the  screen returns to the “1. User” screen.  The followings show LCD prompts that may appear during the registration process. Register Success! When registration is successful Fail! When registration fails If the fingerprint image is unclear, or if no fingerprint is entered for ten seconds after the FP sensor lights off Duplicated FP! If the fingerprint registered already is registered again  If  registration  fails  even  if  you  try  to  repeat  2-3  times  depending  on  the  correct  fingerprint registration method, it is recommended to authenticate using the card.   3.3.1.2. Register as “2. FP”  Register and authenticate using the card only.    Place the card to register on the LCD. To cancel and exit the registration, press [ESC] button.  When  the  registration  is  completed,  select  “Add  FP”.  If  it  fails,  the  screen  returns  to  the  “1. User” menu.  The followings show LCD prompts that may appear during the registration process. Register Success! When registration is successful Fail! When registration fails Duplicated Card! If the card registered already is registered again   3.3.1.3. Register as “FP or Card”  The user can be registered using both card and fingerprint and then authenticated using either card or fingerprint.  The user should register his/her fingerprint (see Fingerprint Registration) and then his/her card (see Card Registration).
AC-2100 Plus  사용자 가이드                                                               28 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.3.1.4. Register with “FP and Card”  The user can be registered using card and fingerprint. Authentication is performed for the card and then for the fingerprint.  The user should register his/her fingerprint (see Fingerprint Registration) and then his/her card (see Card Registration).   3.3.2. Delete User  Select [F3~]→[1.User]→[2.Delete] on the main screen, and the following screen will appear.     Enter the ID of the new user you wish to delete, and press [F4] button long.   Enter the ID of the user you want to delete from the registered users of the terminal and press [F4] button long, the successful buzzer will sound and all the information will be deleted from the terminal. However, data deletion from the terminal does not mean data deletion from the server. To delete the data permanently, it must be deleted from the server as well.  If the ID of an unregistered user  is entered, the message of “Unregister” with “Fail” buzzer is displayed on the LCD and then the screen goes to the “1. User” menu.  When  deleting,  both  general  users and  administrators are  deleted without  distinction. So  you have to watch out the deletion of administrator unknowingly. If users who are not exist in the network server but registered in the terminal are deleted, the data cannot be recovered. Therefore, special cautions are required.
AC-2100 Plus  사용자 가이드                                                               29 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.3.3. Modify User  Select [F3~]→[1.User]→[3.Modify] on the main screen, and the following screen will appear.    Enter the ID of the user you wish to change, and press [ENT] button long.  Both  general  users  and  administrators  can  be  changed  without  distinction.  If  the  ID  of  an unregistered user (or administrator) is entered, the message of “Unregister” with “Fail” buzzer is displayed on the LCD and then the screen goes to the “1. User” menu.  The changeable items of users are different according to the user authentication method and are classified as below.    Select [1] to change the authentication method; [2] to modify the authentication level; [3] to add the fingerprint to the relevant ID; and [4] to add the card.  ※Up  to  10  fingerprints/cards  per  ID  can  be  registered.  If  you  try  to  register  more  than  10 fingerprints/cards, when selecting [3] or [4], “Fail” buzzer occurs and the message of “User FP/Card Full !” is displayed on the LCD.      [1] When selecting “Auth Type”    By using [↑][↓] buttons, select the authentication method and “And” or “Or”, and press “Next” button.
AC-2100 Plus  사용자 가이드                                                               30 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  To modify, select the authentication methods referring to the aforementioned process of [3.3.1.1] to [3.3.1.4].  [2] When selecting “1:1 Level”    Recommended Setting: ‘0’  To modify, the new set value should be entered. If this value is  set to ‘0’, the 1:1 Level set  in  the terminal  is  used instead of the user-specific authentication level.   [3] When selecting “Add FP”    Enter your fingerprint referring to “1.8. How to register and enter the fingerprint” as aforesaid.  When the fingerprint sensor lights on, place your finger on the fingerprint input window. When “Ppik” buzzer occurs, wait for about 2~3 seconds until the light turns off, and lift your finger. When the first fingerprint is successfully entered, the message of “Please try again” is displayed. Enter the fingerprint entered just now once again.    Enter the fingerprint entered just now once again.  It should be noted that when entering the second fingerprint after entering the first fingerprint, you  must  release  your  finger  from  the  fingerprint  input  window  and  then  enter  the  second
AC-2100 Plus  사용자 가이드                                                               31 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr fingerprint  again.  When  the  registration  is  completed,  select  “Add  FP”.  If  it  fails,  the  screen returns to the “3. Modify” menu.   The followings show LCD prompts that may appear during the registration process. Register Success! When registration is successful Fail! When registration fails If the fingerprint image is unclear, or if no fingerprint is entered for ten seconds after the FP sensor lights off Duplicated FP! If the fingerprint registered already is registered again User FP Full! If ten fingerprints have been registered in the relevant ID   [4] When selecting “Add CARD”            To cancel the registration, press [ESC] button.      When placing your card on the LCD, the successful buzzer occurs and the newly entered card number is added. If card change fails, the “Fail” buzzer occurs and the screen returns to the “3. Modify” menu.  The followings show LCD prompts that may appear during the registration process. Register Success! When registration is successful Fail! When registration fails Duplicated Card! If the card registered already is registered again User Card Full! If ten fingerprints have been registered in the relevant ID
AC-2100 Plus  사용자 가이드                                                               32 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.3.4. Add Administrator  Select [F3~]→[1.User]→[4.Add Admin] on the main screen, and the following screen will appear.    Enter the ID of the administrator you wish to register, and press [F4] button long.   ※  Since  then,  the  administrator  registration  process  is  same  as  the  general  user  registration process.  Only users registered as administrators have the authority to change the operating environment of  the terminal, and  register/modify/delete all  the  information  of users  saved in  the  terminal. Therefore, special attention is required for registration of terminal administrators.   3.3.5. Delete All Users  Select [F3~]→[1.User]→[5.Delete All] on the main screen, and the following screen will appear.    Select [1] to delete all users, and [2] to cancel.  After requesting reconfirmation, all users including administrators are immediately deleted. Before using this function, special attention is required.  After successful  deletion, the successful buzzer  occurs  and  then  the  screen  returns  to  the  “1. User” menu.
AC-2100 Plus  사용자 가이드                                                               33 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.4. Network Setting  Select [2.Network] on the main menu, and the following screen will appear.    Press [↑][↓] buttons to select the menu you want to change, and press [ENT] button.   3.4.1. Terminal ID  Select [F3~]→[2.Network] → [1.Terminal ID] on the main screen, and the following screen will appear.  3.4.1.1. Terminal ID    This ID is a unique ID used to allow the server to identify the terminal. The default is ‘00000001’. Default Setting: “00000001”  This ID must match the door ID set to the server program and is entered as an 8-digit number. Press [ENT] button long, and go to the next menu.   3.4.1.2. Authentication Priority [NS / SN / NO / SO] Setting    Select [1] for NS, [2] for SN, [3] for NO, and [4] for SO. Default Setting: ‘2.SN’
AC-2100 Plus  사용자 가이드                                                               34 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  This menu is to determine the authentication priority between the terminal and the network, the default is ‘2. SN’, and the authentication method in each mode operates as follows.  NS If the terminal is connected to the server, authentication is attempted from the server. If the terminal is disconnected from the server due to a network failure, etc., authentication is attempted from the terminal. SN Even if the terminal is connected to the server, authentication is attempted from the terminal. The authentication result is sent to the server in real time. However, if the entered user is not registered in the terminal, authentication is attempted from the server. (If there is any fingerprint user in the terminal, the 1:N fingerprint authentication is not performed in the server.) NO Even if the user is registered in the terminal server, authentication is performed through the server only. SO Only users registered in the terminal are authenticated. If the terminal is connected to the server, the authentication result is sent to the server in real time.  The authentication priority may be set flexibly depending on the situation such as the number of terminals  connected  to  the  server,  the  number  of  authenticated  users,  or  network  failure. However, if more than 10 terminals are connected to the server and so concurrent authentication is  often  attempted,  or  if  network  failure  often  occurs,  it  is  recommended  to  attempt  SN authentication (set to ‘2’).  After entering correctly, press [ENT] button, and the screen will go to the upper menu.
AC-2100 Plus  사용자 가이드                                                               35 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.4.2. IP Setting  Select [F3~]→[2.Network] → [2.Terminal Net] on the main screen, and the following screen will appear.  3.4.2.1. Connection Method Setting    Select [1] if Static IP is assigned, and select [2] to set IP using DHCP. Default Setting: ‘1.Static’  This refers to how the terminal is connected to the network. The default is ‘1’ (Static). Select [1] when using the Static IP assigned from the connected network, and select [2] when using the IP assigned from the DHCP server which exists in the connected network.  After entering correctly, press [ENT] button to move to the next setting.  ※ If the connection method is set to ‘Static IP (1)’, the following procedures such as “3.4.2.2. Terminal  IP  Setting”,  “3.4.2.3.  Subnet  Mask  Setting”,  and  “3.4.2.4.  Gateway  Setting” should  be  set  respectively.  However,  if  the  connection  method  is  set  to  the  dynamic  IP supported by DHCP, the setting is unnecessary and so omitted.   3.4.2.2. Terminal IP Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers Default Setting: “192.168.000.003”      Set the IP address assigned to the terminal.  After entering correctly, press [F4] button long to move to the next setting.
AC-2100 Plus  사용자 가이드                                                               36 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.4.2.3. Subnet Mask Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers. Default Setting: “255.255.255.000”  This is to set the subnet mask of the network connected to the terminal.  After entering correctly, press [F4] button long to move to the next setting.   3.4.2.4. Gateway Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers. Default Setting: “192.168.000.001”  This is to set the gateway IP of the network connected to the terminal.  After entering correctly, press [ENT] button long, and the screen will go to the upper menu.   3.4.3. Server IP Setting  Select [F3~]→[2.Network] → [3.Server Net] on the main screen, and the following screen will appear.
AC-2100 Plus  사용자 가이드                                                               37 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.4.3.1. Connection Method Setting    Select [1]  if  Static IP  is  assigned, and  select  [2]  to set  IP using DDNS. Default Setting: ‘1.Static’  This is the way that the terminal is connected to the network. Select [1] when using the Static IP assigned from the connected network, and select [2] when using the IP assigned from the DDNS server.  After entering correctly, press [ENT] button to move to the next setting.  ※ If the connection method is set to ‘Static IP (1)’, the following procedures such as “3.4.3.2. Sever IP Setting” and “3.4.3.3. Server Port Setting” should be set respectively. However, if the connection method is set to ‘2. DDNS’, DDNS ID needs to be additionally set and so “4.4.3.4. DDNS ID Setting” is added.   3.4.3.2. Sever IP Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers. Default Setting: “192.168.000.002”  This is to specify the IP Address of the network server connected to the terminal.  After entering correctly, press [F4] button long to move to the next setting.
AC-2100 Plus  사용자 가이드                                                               38 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.4.3.3. Sever Port Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers. Default Setting: “09870”  This is to specify the Port of the network server connected to the terminal.  After entering correctly, press [F4] button long, and the screen will go to the upper menu.   3.4.3.4. DDNS ID Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers. Default Setting: “000000001”   This appears only when the server connection method is set to “2. DDNS”. This is to specify the DDNS ID of the DDNS server connected to the terminal.  After entering correctly, press [F4] button long to move to the next setting.
AC-2100 Plus  사용자 가이드                                                               39 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.4.3.5. DDNS IP Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers. Default Setting: “210.116.104.058”  This is to specify the IP Address of the network server connected to the terminal.  After entering correctly, press [F4] button long to move to the next setting.   3.4.3.6. DDNS Port Setting    Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers. Default Setting: “09880”  This is to specify the Port of the network server connected to the terminal.  After entering correctly, press [F4] button long, and the screen will go to the upper menu.
AC-2100 Plus  사용자 가이드                                                               40 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5. Option Setting  Select [3.Option] on the main menu, and the following screen will appear.    Press [↑][↓] buttons to select the menu you want to change, and press [ENT] button.      3.5.1. Application Setting  Select [F3~] → [3.Option] → [1. Application] on the main screen, and the following screen will appear.    Set the operating mode that you want to set. Default Setting: ‘1.Access’  This is to set an operating mode of the terminal. Select ‘1’ for simple access control; ‘2’ for T&A control; and ‘3’ for Food Service management.      After  selecting,  press  [ENT]  button  to  move  to  the  detail  setting  menu  according  to  each operating system.
AC-2100 Plus  사용자 가이드                                                               41 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.1.1. When setting to “[1.Access]” or “[2.T&A]”  By setting  the  default  time  for  each T&A mode,  after  authentication, the  terminal  display mode can be turned into the automatically set T&A mode.    If time setting is unnecessary, it is set to ‘00:00-00:00’.    This is to set the default attendance time. Press [←][→] buttons to move to the digit you want to change, and press [↑][↓] buttons to change the numbers.  Within the set time zone, the Attend mode is always displayed if another function key is not pressed. Even if the Leave mode is authenticated by pressing [F2] button, the terminal display mode is automatically turned into the Leave after authentication. Therefore, it is convenient to manage T&A.  After <F1 Time>, set <F2 Time>, <F3 Time>, <F4 Time>, and <Access Time> in the same way. As shown below, each time zone must be set not to overlap each other.  (Ex.) F1 Time=06:00~09:59, F2 Time=17:00~22:00 <F1 Time>   06:00~09:59 <F2 Time>   17:00~22:00       Subsequently, press [ENT] button, and the following screen will appear.    Default Setting: ‘2.No’      At  least  five  authentication  modes  may  be  set  if  necessary.  Whether  to  use  function  keys  of F5~F6 is determined using F1~F3 keys. When setting to ‘1.Yes’, press the F1(F2,F3) mode once more under the F1(F2,F3) mode, and it will be changed into the F5(F6,F7) mode.
AC-2100 Plus  사용자 가이드                                                               42 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr     Default: ‘1.No’  This is the menu to select whether to use the printer or not. If the authentication is set to  ‘1’  or  ‘2’  with  successful  authentication,  the  Terminal  ID,  User  ID,  Date  and Authentication mode are printed out through the printer connected to the RS232 port of Terminal. The printer used is “SRP-350” Serial Type model.       Subsequently, press [ENT] button, and the following screen will appear.    Default Setting: All ‘V’      Set whether to use each function key. When setting to ‘V’, it means that the authentication mode may be changed when pressing the function key. When setting to Blank, the authentication mode is not changed in spite of pressing the key. When this mode is used only for Attend or Leave, it is available by unchecking other function keys.  After selecting the set value, press [ENT] button, and all authentication settings will be finished and the screen will move to the upper menu.
AC-2100 Plus  사용자 가이드                                                               43 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.1.2. When setting to “[3.Cafeteria]”    If time setting is unnecessary, it is set to ‘00:00-00:00’.  This is to set the breakfast time. Breakfast is unconditionally authenticated within the set time zone. After setting the breakfast time, set <Lunch>, <Dinner>, <Supper>, and <Snack> in order in the same way. The unused meal time is set to ‘00:00-00:00’.  Each time zone must be set not to overlap each other. When the time is not set to the food time zone,  the  terminal  displays  “Locked!”  message.  As  the  terminal  is  locked,  all  inputs  are blocked except for access to the menu mode.
AC-2100 Plus  사용자 가이드                                                               44 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  When <Snack> is set, the menu to check whether to duplicate appears as shown below.    Default Setting: ‘2.No’  If the  mode is  set  to  ‘No’, authentication is  once  allowed within the  same meal  time zone. When  attempting  authentication  again,  the  “Duplicated!”  message  is  displayed  and  the authentication fails.  Subsequently, press [ENT] button, and the following screen will appear.     Default: ‘1.No’  This is the menu to select whether to use the printer or not. If the authentication is set to  ‘1’  or  ‘2’  with  successful  authentication,  the  Terminal  ID,  User  ID,  Date  and Authentication mode are printed out through the printer connected to the RS232 port of Terminal. The printer used is “SRP-350” Serial Type model.       Subsequently, press [ENT] button, and the following screen will appear.    Default Setting: All ‘V’
AC-2100 Plus  사용자 가이드                                                               45 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr      Set whether to use each function key. When setting to ‘V’, it means that the authentication mode may be changed when pressing the function key. When setting to Blank, the authentication mode is not changed in spite of pressing the key. When this mode is used only for Attend or Leave, it is available by unchecking other function keys.  After selecting the set value, press [ENT] button, and all authentication settings will be finished and the screen will move to the upper menu.   3.5.2. Authentication Method Setting  Select [F3~] → [3.Option] → [2. Verify] on the main screen, and the following screen will appear.  3.5.2.1. Set whether to display ID upon successful authentication    Default Setting: ‘2.User Name’  - ‘1’: displays the authenticated user ID - ‘2’: displays the user name on the LCD. If there is no user name, the user ID is displayed. But it marks Max 16 letters for English, Max 8 letters for Korean (Japanese/Chinese) - ‘3’: displays the User Key which is registered upon user registration. - ‘4’: displays the message entered upon user registration. But it marks Max 16 letters for English, Max 8 letters for Korean (Japanese/Chinese)   (Caution) * UserName and Message are set in the server. For output, the user information must be downloaded. * UserName and Message must be set to the same language as the terminal language.  (Example) OK!<0001>  Subsequently, press [ENT] button to move to the next setting.
AC-2100 Plus  사용자 가이드                                                               46 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.2.2. Set whether to permit authentication using card only    Default Setting: ‘2.No’  This option makes it possible to authenticate using card only without fingerprint. Even if the user is registered in FP and Card, he/she can be authenticated using card only in the terminal that this option is set to ‘1’.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.5.2.3. To authenticate only using the information saved in the Smart Card    Default Setting: ‘2.No’  This option makes it possible to authenticate only using the user information and fingerprint recorded in the card without downloading users in the terminal. To operate this option, the terminal must be equipped with the SC card reader and it must be set to use the FP card.   After selecting the set value, press [ENT] button, and the screen will go to the upper menu.
AC-2100 Plus  사용자 가이드                                                               47 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.2.4. Blocking Time Setting    Default Setting: 00000 (Unit: Second)  This option is to prohibit the user from re-authenticating within the set time. There is no limit when the mode is set to '0'. However, if it is set to the greater value than ‘0’, re-authentication cannot be permitted until the time lapses more than the set time after successful authentication.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.5.2.5. Global Block Setting    Default Setting: ‘2.No’  This option is to prohibit the user from authenticating within the short time. After successful authentication, the terminal function is blocked during the blocking time set previously.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.
AC-2100 Plus  사용자 가이드                                                               48 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.2.6. NetErr TimeOut    – Network Error Time Setting (Second)    Default Setting: ‘05’  In  the  server  authentication  mode,  if  the  network  error  time  is  set,  the  time  to  wait  for authentication can be set. For example, if the error time is set to 5 seconds, when the user does not receive any response from  the  server  for  5  seconds  after  authentication  request,  an  error  message  comes  out. (However, the user is processed as authentication failure.)  After  selecting  the  set  value,  press  [ENT]  button,  and  all  authentication  settings  will  be finished and the screen will move to the upper menu.
AC-2100 Plus  사용자 가이드                                                               49 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.3. Door Setting  Select [F3~] → [3.Option] → [3.Doorlock] on the main screen, and the following screen will appear.   3.5.3.1. Door Open Time Setting    Default Setting: ‘03’(Unit: Second)  This option is to specify the time when after authentication through the terminal, the door is opened  and  then  closed.  Strike  type  means  the  time  when  if  opening  the  door  after authentication, the door is automatically locked again. In the case of Dead Bolt type and Auto Door, the door will work regardless of the value.  If the mode is set to ‘00’, it is impossible to control the door. '00' must be set only when the door is not connected to Lock.  After selecting the set value, press [F4] button to move to the next setting.   3.5.3.2. Door Open Alarm Setting    Default Setting: ‘00’  This option allows the terminal to check the time when the door is open. If the door is open over the set time (minimum 5 seconds to maximum 30 seconds), an alarm occurs. When the time is set to ‘00’, no alarm occurs. Even if the time is set to 01~04, an alarm starts to sound after the lapse of at least 5 seconds.  The door must be  closed within  the set time. But, it may not  be closed due to unforeseen circumstances. The alarm allows users to check the cause that the door is unclosed and take any action so that the door can be closed normally.
AC-2100 Plus  사용자 가이드                                                               50 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr To use this function, the lock must have the function to monitor whether the door is open or close.  The  monitoring  pin  of  the  lock  must  be  also  connected  to  the  terminal.  To  check whether the door is open or close, the mode must be set to ‘2’ or ‘3’.  After selecting the set value, press [F4] button long, and the screen will finish all the setting of the door and move to the upper menu.   3.5.4. Volume Setting  Select [F3~] → [3.Option] → [4.Sound] on the main screen, and the following screen will appear.  3.5.4.1. Voice Volume Setting    Default Setting: ‘3’  This option is to set the volume during voice guidance. If the volume is set to ‘0’, the voice message does not come out.  Press [ENT] button to move to the next setting.
AC-2100 Plus  사용자 가이드                                                               51 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.4.2. Buzzer Volume Setting    Default Setting: ‘3’  This  option  is  to  set  the  terminal  buzzer  volume.  The  buzzer  occurs  silent  for  ‘0’,  small volume for ‘1’, and large volume for ‘3’.  Press [ENT] button to move to the next setting.   3.5.4.3. Case Open Alarm Setting    Default Setting: ‘1.Yes’  This  option  is  to  set  whether  an  alarm  occurs  when  the  terminal  case  is  open.  The  alarm occurs for ‘1’ and it does not occur not for ‘2’.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.5.6. Current Time Setting  Select [F3~]→[3.User]→[6.Time] on the main screen, and the following screen will appear.  3.5.6.1. Time Synchronization Setting    Default Setting: ‘1.Auto’
AC-2100 Plus  사용자 가이드                                                               52 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  This option is to set how to synchronize the current time of the terminal with the server time. Set to  ‘1.Auto’  to  automatically  synchronize  with  server  time,  and  set  to  ‘2.Manual’  to  manually synchronize with server time.  Press [ENT] button to move to the next setting.   3.5.6.2. Calendar Setting    Default Setting: ‘1.Gregorian’  This option is to set how to display the current date in the terminal. The date is generally set to ‘1. Gregorian’, but ‘2.Persian’ when using the Persian calendar specially.  Press [ENT] button to move to the next setting.
AC-2100 Plus  사용자 가이드                                                               53 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.6.3. Current Time Setting      The  current time of  the  terminal is  displayed in  the  order of "2009:Year,  08:Month,  01:Day, 21:Hour, 18:Min, 06:Sec". To modify, move to the desired position using [←][→] buttons, and modify the existing values using [↑][↓] buttons.  Press [ENT] button to move to the next setting.   3.5.6.4. Time Display Setting    Default Setting: ‘2.05:00 PM’  This option is how to display the current time of the terminal. When setting to ‘1’, the time is displayed  to  the  24-hour  time.  When  setting  to  ‘2’,  the  time  is  displayed  by  separating  with AM/PM.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.5.7. RS485 Set  Select [F3~] →  [3.Option] → [7.RS485 Set]  → [ENT] on the main  screen, and the following screen will appear.
AC-2100 Plus  사용자 가이드                                                               54 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.5.7.1. RS485 Set  This option is to set RS485 ID in order to work together with RS485 device.    Press [↑][↓] buttons to select the ID value, and press [ENT] button. Default Setting: ‘0’  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.6. Terminal Information Inquiry  Select [3.Information] on the main menu, and the following screen will appear.    All the environmental settings of the terminal can be checked in order.  Press [↑][↓] buttons and scroll them up and down, and you can in order check the settings in the following table.
AC-2100 Plus  사용자 가이드                                                               55 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr Version Terminal firmware version WorkMode Terminal operating modes (T&A + security/T&A/food service) Language Language setting Auth Mode Authentication priority 1:1 Level Authentication level applied when 1:1 authentication 1:n Level Authentication level applied when 1:n authentication Terminal Id Terminal ID Net Type Network connection methods (Static IP/DHCP) Terminal IP Terminal IP address Gateway Terminal gateway address Subnet Mask Terminal subnet mask address Server Type Network server connection mode setting Server IP IP address of the network server connected to the terminal Server Port Port number of the network server program MAC Addr Terminal MAC address Card Ver Card reader module firmware version Card Format Card data display format All User The total number of users registered in the terminal, including administrators All Admin The number of administrators registered in the terminal Max User The maximum number of users who can be registered in the terminal All FP The total number of fingerprints saved in the terminal Max FP The maximum number of fingerprints that can be registered in the terminal All Log The number of the authentication results saved in the terminal Max Log The maximum number of the authentication results that can be saved in the terminal Serial Num Terminal serial number    3.7. Additional Function (Extra Function)  Select [5.Ext Function] on the main menu, and the following screen will appear.    Press [↑][↓] buttons to select the menu you want to change, and press [ENT] button.
AC-2100 Plus  사용자 가이드                                                               56 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   3.7.1. Terminal Lock Setting  Select [F3~]→[5.Ext Function]→[1.Lock Term] on the main screen, and the following screen will appear.    Default Setting: ‘2’ (Unlock Terminal)   This function allows the administrator to directly lock or unlock the terminal without the server program. If it is set to ‘1’, nobody can access the office until the administrator releases the set.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.7.2. Card Number Inquiry  Select [F3~]→[5.Ext Function]→[2.Read Card] on the main screen, and the following screen will appear.      This is an additional function regardless of the terminal environment setting. In the case of the terminal that the card reader is added, the card number can be checked for card registration via the server. Place the card on this screen, and the card number will be displayed on the LCD.  To exit the card read, press [ESC] button to move to the upper menu.
AC-2100 Plus  사용자 가이드                                                               57 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.7.3. Monitor Input Port Setting  This option acts to connect the sensor to the terminal input port, and send a notice message to the server when the status is changed.  Select [F3~]→[5.Ext Function]→[3.Monitor] on the main screen, and the following screen will appear.  (Caution) DM2 is a currently unused spare port. Before using the relevant function, check the required ports and install.   3.7.3.1. Monitor 1 Input Port Setting    Set when connecting an external contact to DM0. (When using a motor lock, set to 1 or 2.) Default Setting: ‘0.None’  - ‘0.None’: When nothing is connected - ‘1.NO’ or ‘2.NC’: When the open door status monitoring pin is connected - ‘3.Fire NO’ or ‘4.Fire NC’: When the fire detection sensor is connected - ‘5.Panic NO’ or ‘6.Panic NC’: When the panic situation detection sensor is connected - ‘7.EMC NO’ or ‘8.EMC NC’: When the emergency detection sensor is connected - ‘9.Ctrler Out’: When the authentication result is sent to the external controller (Connect the REDled of controller to DM0 or DM1 through the board has the TR. Set the relevant pin to ‘9.Ctrler Out’. WiegandOut must be set.)  Press [ENT] button to move to the next setting.   3.7.3.2. Monitor 2 Input Port Setting    Set when connecting an external contact to DM1. (When using a motor lock, set to 1 or 2.) Default Setting: ‘0.None’  - ‘0.None’: When nothing is connected - ‘1.NO’ or ‘2.NC’: When the open door status monitoring pin is connected
AC-2100 Plus  사용자 가이드                                                               58 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr - ‘3.Fire NO’ or ‘4.Fire NC’: When the fire detection sensor is connected - ‘5.Panic NO’ or ‘6.Panic NC’: When the panic situation detection sensor is connected - ‘7.EMC NO’ or ‘8.EMC NC’: When the emergency detection sensor is connected - ‘9.Ctrler Out’: When the authentication result is sent to the external controller (Connect the REDled of controller to DM0 or DM1 through the board has the TR. Set the relevant pin to ‘9.Ctrler Out’. WiegandOut must be set.)  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.7.4. Duress FP Setting  Select [F3~]→[5.Ext Function]→[4.Duress FP] on the main screen, and the following screen will appear.  3.7.4.1    Duress FP  This function allows users to use an alarm when the duress fingerprint is entered.    Set whether to use the duress fingerprint alarm. Default Setting: ‘2.No’  The  default  setting  is  '2.No'.  When  it  is  set  to  ‘1.Yes’,  if  the  pre-registered  fingerprint  is authenticated, the ‘L2’ Pin will output the DC12V. If any emergency detection device such as a siren is connected to this Pin, it will operate.  If <Duress FP> is set to ‘1.Yes’, the menu for setting the time corresponding to 12V will appear.    Default Setting: ‘03’ (Unit: Second)   To modify, Press [←][→] buttons to move to the desired position, and press [↑][↓] buttons to change the existing value.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.
AC-2100 Plus  사용자 가이드                                                               59 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.8. Device Setting  Select [6.Device] on the main menu, and the following screen will appear.    Press [↑][↓] buttons to select the menu you want to change, and press [ENT] button.      Most of device settings are the option that does not need to change after installation. It is recommended that they are not changed unless there is any clear purpose.   3.8.1. System Configuration  Select [F3~] → [6.Device] → [1. System Conf] on the main screen, and the following screen will appear.  3.8.1.1. User ID Digit Setting    Default Setting: ‘4’   This is a portion for setting the length of user ID. The length of user ID can be set to the 2~8 digit. It should be equal to the length of ID registered in the server program. If the 6-digit ID of ‘000075' is registered in the server program, the mode is set to ‘6’.  After setting, press [ENT] button to move to the upper menu.
AC-2100 Plus  사용자 가이드                                                               60 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.8.1.2. Language Setting    Default Setting: ‘0.English’  If the language setting is changed, the voice message and the message on the LCD are changed into the set language.   3.8.2. Card Reader Format Setting  Select [F3~] → [6.Device] → [2. Card Format] on the main screen, and the following screen will appear.    Default Setting: ‘0.Default’  This option is to specify the format that displays the read card number. When setting to Hexa, the  format  is  displayed  to  the  hexadecimal  number.  When  setting  to  Decimal,  the  format  is displayed  to  the  decimal  number.  In  the  device  equipped  with  the  RF  (low  frequency)  card reader, if the mode is set to ‘4.Format 5’ and it reads EM Card, the card number is displayed to the hexadecimal number of 10byte.   3.8.3. Fingerprint Sensor Setting  Select [F3~] → [6.Device] → [3. FP Sensor] on the main screen, and the following screen will appear.
AC-2100 Plus  사용자 가이드                                                               61 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.8.3.1. 1:1 Level Setting    Default Setting: ‘4’  This option is to set the match degree with the same fingerprint when comparing the fingerprint on  the  fingerprint  input  window  with  the  user  fingerprint  saved  in  the  database.  The  higher authentication  level  may  ensure  the  higher  security.  But  it  requires  the  relatively  high concordance rate. When authenticating User ID, it high likely to deny authentication.  In case of 1:1 Authentication Level, if the ID entered to the authentication level that underwent the authentication process with the ID input is ‘1234’, this option finds the fingerprint registered to  the  ID  of  ‘1234’  from  the  terminal  database  and  compares  it  with  the  fingerprint  on  the fingerprint input window.  However, in  case  of  1:1  authentication, if  the 1:1 authentication level of  users is  not set to  ‘0’ (using the terminal authentication level), the 1:1 authentication level of users is applied.  Press [ENT] button to move to the next setting.   3.8.3.2. 1:N Level Setting    Default Setting: ‘4’  This option is to set the authentication level using the fingerprint only without ID input. This option is used to find the fingerprint matched by comparing the fingerprint on the fingerprint input window with the user fingerprint saved in the database.  In  case  of  1:N  authentication,  the  user-specific  authentication  level  is  not  set.  Therefore, authentication is always based on the terminal authentication level.  Press [ENT] button to move to the next setting.
AC-2100 Plus  사용자 가이드                                                               62 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.8.3.3. LFD Setting    Default Setting: ‘1.None’  This option is to set the LFD level that can prevent fake fingerprints from entering. The higher LFD level may ensure the higher function that prevents the input of fake fingerprints made of rubber, paper, film, and silicon. However, too dry fingerprints may not be entered even when entering actual fingerprints.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.8.3.4. Similar fingerprint registration restriction setting    Default Setting: ‘1.Yes’  If the mode is set to ‘1.Yes', this option acts to check whether a new fingerprint is the same as the pre-registered fingerprint, and to prevent the same fingerprint from being registered as the ID of another user.  After selecting the set value, press [ENT] button, and the screen will go to the upper menu.   3.8.4. Wiegand Speaker Output  Select  [F3~]  →  [6.Device]  →  [4.Wiegand]  on  the  main  screen, and the  following screen will appear.
AC-2100 Plus  사용자 가이드                                                               63 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   Default Setting: ‘1’   This option is used only when the terminal is equipped with a separate controller operated by Wiegand input. After authentication, the following types of data are sent to the Wiegand port of the terminal.  1.None General case. The Wiegand Out port is not used. 2.26bit  “Sitecode [1 byte] + User ID [2 bytes]” are transferred. User ID should be set to the 4-digit or less number. Example) SiteCode:045, UID:6543 → 1 00101101 0001 1001 10001111 0 3.34bit  “Sitecode [1 byte] + User ID [3 bytes]” are transferred. User ID should be set to the 7-digit or less number. However, if User ID is 8 digits, Sitecode is ignored and only “User ID [4 bytes]” is transferred. Example) SiteCode:001, UID:123456 → 0 00000001 00000001 11100010 01000000 0 4.Custom This is the user-defined setting that is available only in the server. Only checking is possible in the terminal.  ※  This option is unrelated to use the Wiegand type card reader. If the mode is set to ‘2’ or ‘3’, the following site code is set.    Default Setting: ‘000’   This  option  is  available only when  Wiegand  Out is  set to  ‘2’  or  ‘3’. The site  code  to send  to Wiegand port including User ID is set to the value of 0~255.  After selecting the set value, press [F4] button, and the screen will go to the upper menu.  3.8.4.1. Bypass Setting
AC-2100 Plus  사용자 가이드                                                               64 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   Default Setting: ‘2.No’   This option is available when the Wiegand card reader is used. When  the  mode  is  set  to  [1],  the  card  information  entering  to  ‘Wiegand  In’  is  bypassed  to ‘Wiegand Out’.   3.8.5. Terminal Initialization  Select [F3~] → [6.Device] → [5.Initialize] on the main screen, and the following screen will appear.    Select [1] to initialize the set value; [2] to initialize the authentication records; [3] to initialize the factory; and [4] to use the UDL10 to backup the DB.   3.8.5.1. Set Value Initialization    Select [1] to initialize, and [2] to cancel.  This option initializes all settings of the terminal except for the MAC (physical) addresses and serial numbers saved in the terminal. But, users and authentication records are not deleted.  When initialization is successfully completed, the “Ppiririck” beep occurs and the screen moves to the upper menu.
AC-2100 Plus  사용자 가이드                                                               65 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 3.8.5.2. Authentication Records Initialization    Select [1] to initialize, and [2] to cancel.  This option deletes all authentication related logs except for set values and users. When initialization is successfully completed, the “Ppiririck” beep occurs and the screen moves to the upper menu.   3.8.5.3. Factory Initialization    Select [1] to initialize, and [2] to cancel.  This  option  deletes  all  settings,  users  and  log  information  except  for  the  MAC  (physical) addresses  and  serial  numbers  saved  in  the  terminal,  and  initializes  the  terminal  to  the  status shipped at a factory.  When initialization is successfully completed, the success buzzer occurs and then the terminal is rebooted.   3.8.5.4. UDL(USB Data Logger) Backup  - If the UDL10 has the USB memory card is inserted, the mode moves to the sub-menu. If USB is not inserted, the warning message of ‘Not Detected Memory’ is displayed.
AC-2100 Plus  사용자 가이드                                                               66 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   DB Backup Menu.   Export Log - Used when the log data saved in the AC2100 terminal is exported to USB. - Data is saved with a file name  of  LOG.DAT  in the  place  of  “USB  top-level  folder  → AC2100 folder → 00000000 (8-digit terminal ID) folder → LOG folder”. - Only log data can be saved, except for photos.   Export User - Used when the user data saved in the AC2100 terminal is exported to USB. - Data is saved with a file name of USER.DAT in the unisuser folder. - The number of exported users can be checked on the LCD.   Import User - Used when the user data (USER.DAT) saved in USB is imported into the terminal. - The user file (USER.DAT) must be saved with a file name of USER.DAT in the unisuser folder. - The size of imported data can be checked on the LCD.   Upgrade - Used when  upgrading the  terminal firmware by  using the  firmware  data (ac2100.bin) saved in the USB. - The  firmware  file  is  ‘ac2100.bin’.  To  upgrade,  it  must  be  saved  with  a  file  name  of ac2100.bin in the AC2100 folder. - The size of imported data can be checked on the LCD.  Caution!!   When removing the USB or powering off the terminal during upgrading, the product may not work properly. Special caution is required.   3.8.6. External Device Setting  Select [F3~] → [6.Device] → [6.Ext Device] on the main screen, and the following screen will appear.
AC-2100 Plus  사용자 가이드                                                               67 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   Default Setting: ‘1.None’  This option is available when connecting the Slave Reader using the card or fingerprint to the terminal  in  order  to  use  as  a  secondary  authentication  device.  The  mode  is  set  to  ‘2’  when connecting the Wiegand card reader, and ‘3’ when connecting the SR100.    Press [ENT] button to move to the next setting.    Default Setting: ‘2.No’ When setting to ‘1.Yes’, the Anti-Passback in the terminal is checked.  This screen is displayed only when <Ext Device> is set to ‘2’ or ‘3’. This option is used to allow only authorized users to access and leave the office. To this end, the terminal and Slave Reader are installed to both the inside and outside of the door. Only users who access the office by authentication via the terminal can leave the office by authentication via the Slave Reader. When setting ‘1.Yes’, the server authentication is unavailable. The device checks whether Passback is valid in the authentication order between the terminal and the Slave Reader.  Press [ENT] button to move to the next setting.    Default Setting: ‘0’   This option is to set the authentication (T&A) mode saved from the Slave Reader. If the device is set to '0', it is saved as the current authentication mode; saved to F1 when ‘1’, F2 when ‘2’, Access when ‘3’, F3 when ‘4’, and F4 when ‘5’.
AC-2100 Plus  사용자 가이드                                                               68 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr Press [ENT] button to move to the next setting.     Default Setting: ‘1.None’  This screen is displayed only when <Ext Device> is not set to ‘3’. When connecting an external device of LC010 to the terminal, the mode is set to ‘2.Lock Ctrl’. When the terminal interlocks with MCP040, RS485 ID must be set.
AC-2100 Plus  사용자 가이드                                                               69 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  4. How to Use Terminal  4.1. When operating to [1.Access]  - Set to Menu → 3.Option → 1. Application → [1.Access].    4.1.1. Authentication Mode  - Press function keys, change to the desired authentication mode such as F1, F2, F3, F4, and then  perform authentication.  When  perform authentication  without  pressing function  keys specially, the mode is automatically authenticated to the access mode.  - Authentication Method  F1  Authentication:  Press  [F1]  key  to  change  to  the  F1  mode,  and  then  perform authentication. Authentication is performed without changing the mode within the time zone set to the Attend time.  F2  Authentication:  Press  [F2]  key  to  change  to  the  F2  mode,  and  then  perform authentication. Authentication is performed without changing the mode within the time zone set to the Leave time.  F3  Authentication:  Press  [F3]  key  to  change  to  the  F3  mode,  and  then  perform authentication.  F4  Authentication:  Press  [F4]  key  to  change  to  the  F4  mode,  and  then  perform authentication.  Access Authentication:    Press twice  [F4]  key or  press [F4]  key  long  to  change  to  the  access  mode,  and then perform authentication. Or,  perform authentication without changing the mode within the time zone set to the access time.   4.1.2. Authentication Using Fingerprint  After  changing  the  authentication  mode  by  pressing  function  keys,  place  your  finger  on  the fingerprint sensor. Then, the authentication result receiving the fingerprint will appear on the LCD with a voice message.   At the alert status, press [F1] key to change the authentication mode to ‘F1’. ▼
AC-2100 Plus  사용자 가이드                                                               70 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Place your finger on the fingerprint sensor, and the white light is on the fingerprint input window. Keep your finger until the white light is off with a beep sound. ▼  If your fingerprint is successfully authenticated, the voice message of “You are authorized” comes out and a success message is displayed on the LCD.  ※Error  Message:  The  following  messages  will  appear  with  the  voice  message  of  “Place  try again”.  When authentication fails  When the fingerprint is registered but its authentication is attempted out of the access control time   4.1.3. Authentication Using Card  ▶  For users who have registered to [Card] or [FP or Card], place the card on the main screen, and the beep sound will occur and the authentication result will displayed on the LCD.
AC-2100 Plus  사용자 가이드                                                               71 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Press [F2] key to change the authentication mode to Leave. ▼  If your fingerprint is successfully authenticated, the voice message of “You are authorized” comes out and a success message is displayed on the LCD.  Error Message: The following messages will appear with the voice message of “Please try again”.  When a unregistered card is entered  When the card is registered but its authentication is attempted out of the access control time   ▶  For users who are registered with the [FP and Card] Place the card on the main screen, and the “beep” sound occurs. The fingerprint cannot be authorized without going through the following fingerprint input process.
AC-2100 Plus  사용자 가이드                                                               72 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  When the lamp is on the fingerprint input window with the voice message  of  “Please  enter  your  fingerprint”,  enter  your  fingerprint and keep your finger until the “beep” sound occurs.   4.2. When operating to [2.T&A]  - Set to Menu → 3.Option → 1. Application → [2.T&A].  - If you set <Attend> and <Leave > under the condition that the attend time is constant, even if authentication  is  attempted  without  pressing  [F1]  or  [F2]  keys,  the  fingerprint  is authenticated to ‘Attend’ within the time zone set to ‘Attend’ and to ‘Leave’ within the time zone set to ‘Leave’. Therefore, users can reduce the T&A input error.   4.2.1. Authentication Mode  - Press function keys to change the authentication mode to Attend, Leave, Outdoor, Return, and Access, and then perform authentication with each authentication mode.  - Authentication Method  Attend Authentication: Press [F1] key to change to the attend mode, and then perform authentication. Authentication is performed without changing the mode within the time zone set to the Attend time.  Leave Authentication: Press [F2] key to change to  the leave mode, and then perform authentication. Authentication is performed without changing the mode within the time zone set to the Leave time.  Outdoor Authentication: Press [F3] key to change to the outdoor mode, and then perform authentication.  Return Authentication: Press [F4] key to change to the return mode, and then perform authentication.  Access  Authentication:  Press twice [F4]  key  or  press [F4]  key  long to  change  to  the access  mode,  and  then  perform  authentication.  Or,  perform  authentication  without changing the mode within the time zone set to the access time.  4.2.2. Fingerprint Authentication - Press the function key to change the T&A mode. - Enter your fingerprint.  4.2.3. Authentication Using Card - Press the function key to change the T&A mode. - Place the card on the terminal.   4.3. When operating to [2.Cafeteria]  - Set to Menu → 3.Option → 1. Application → [3.Cafeteria].
AC-2100 Plus  사용자 가이드                                                               73 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr - When the mode is set to the food service control, the terminal is locked in the time other than meal times. The meal time must be set to more than one meal per person.   - LCD  When it is not the meal time (No authentication attempt)  The default screen during the meal time  If the authentication is successful  When the mode is set to “Not-allowed Duplicate Authentication Unallowable”, if the authentication is again attempted after successful authentication, a duplicate authentication error is displayed.  - When authenticating with the fingerprint Enter the fingerprint to receive authentication.  - When authenticating with the card Enter the card to receive authentication.  - When  attempting  authentication  without  pressing  the  menu  key,  it  is  automatically authenticated to [Menu 1].
AC-2100 Plus  사용자 가이드                                                               74 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea TEL: +82-2-6488-3000 / FAX: +82-2-6488-3100 E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr FCC Information    This  device  complies  with  part  15  of  the  FCC  Results.  Operation  is  subject  to  the following two conditions :   (1) This Device may not cause harmful interface, and     (2) This device must accept any interference received, including interference that       may cause undesired operation.    Note: This  equipment has  been  tested  and found  to  comply with the limits  for  CLASS  B  digital device,  pursuant  to  Part  15  of  FCC  Rules.  These  limits  are  designed  to  provide  reasonable protection  against  harmful  interference  when  the  equipment  is  operated  in  a  commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed  and  used in  accordance  with the instructions,  may  cause  harmful  interference to  radio communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or  television  reception, which  can  be  determined  by  turning  the  equipment  off and  on,  the  user  is  encouraged  to  try correct the interference by one or more of the following measures:    1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3.  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  receiver  is connected. 1.4. Consult the dealer or experienced radio/TV technician for help.   WARNING Changes  or  modifications  not  expressly  approved  by  the  manufacturer  could  void  the user’s authority to operate the equipment.  “CAUTION : Exposure to Radio Frequency Radiation. Antenna  shall  be  mounted  in  such  a  manner  to  minimize  the  potential  for  human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.

Navigation menu