Ubee Interactive DDW262 D2.0 WLCM model User Manual

Ubee Interactive Corp. D2.0 WLCM model

User Manual

Download: Ubee Interactive DDW262 D2.0 WLCM model User Manual
Mirror Download [FCC.gov]Ubee Interactive DDW262 D2.0 WLCM model User Manual
Document ID1591522
Application IDtUsy3WFltaSXbjlsxiz+4A==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize157.13kB (1964074 bits)
Date Submitted2011-11-30 00:00:00
Date Available2012-01-01 00:00:00
Creation Date2011-09-24 08:47:34
Producing SoftwareAcrobat Distiller 9.3.2 (Windows)
Document Lastmod2011-11-07 17:47:41
Document Title欢迎使用
Document CreatorAcrobat PDFMaker 9.1 for Word
Document Author: huangcc

DDW262 D2.0 WLCM model and
噝 Connect the device into an electrical outlet on a
different circuit than the interfered device is
connected.
Router Safety and Installation
Product Insert
噝 Consult the dealer or an experienced radio/TV
technician for help.
i Federal Communications Commission
i FCC Regulatory Information
(FCC) Interference Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation. (3) There are two statements
for this product:
This device has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
device generates, uses, and can radiate radio
frequency energy. If not installed and used in
accordance with the instructions, the device may
cause harmful interference to radio communications.
There is no guarantee, however, that interference
will not occur in a particular installation. If this device
causes harmful interference to radio or television
reception, which can be determined by turning it off
and on, the user can try to correct the interference
by one of the following measures:
噝 Increase the separation between the device and
the equipment with which it is interfering (for
example, a television or radio).
FCC Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this device.
IEEE 802.11b or 802.11g or 802.11n operation of
this device in the U.S.A. is firmware-limited to
channels 1 through 11.
i FCC Radiation Exposure Statementʳ
4.Mounting: When this device is placed upright
with the aid of the stand, fix the stand at a
90-degree angle to the device. Otherwise, the
device may tip over. Refer to Figure 1.
噝This device complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
噝This device should be installed and operated at a
minimum distance of 20cm between itself and
your body.
噝This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
噝 ethernet 1 to 4: Connect the Ethernet RJ45
cable. Connect the other to the Ethernet port on
the PC or NIC.
噝 cable: Connect the coaxial cable (not included)
that comes from the cable wall outlet or cable
splitter (not included) to the cable connector on
the back of the device.
噝 WPS: Use the Wi-Fi Protected Setup found on
top of the device to connect PIN-protected Wi-Fi
equipment to this device. Refer to the user guide
for more information.
3. Connect one end of the power adapter to the
power port on the device. Connect the other end
to an electric outlet. Important: Use only the
power adapter that is shipped with the device.
i Safety Notices
1. Grounding: Install the device to include
grounding the coaxial cable to the earth at the
building entrance per ANSI/NFPA 70 and the
National Electrical Code (NEC, in particular,
Section 820.93, Grounding of the Outer
Conductive Shield of a Coaxial Cable).
Figure 1: Device Stand at 90 Degree Angle
i Installation
Follow these procedures to install the device. Refer
to Figure 2.
2. Disconnecting: If the device becomes damaged
or encounters some other abnormality,
disconnect the power plug from the wall outlet
immediately.
1. Connect one end of a coaxial cable (not included)
to the cable port on the device. Connect the other
end to the cable wall outlet or a cable splitter (not
included). Do not bend or over-tighten the cables
as this may strain the connector and cause
damage. If you plan to connect the device and a
3.Installing: Install the device in a location not to
exceed the maximum temperature of 40 degrees
Celsius (104 degrees Fahrenheit).
television to the same cable wall outlet, you must
use a cable line splitter (not included).
2. Connect one end of the supplied Ethernet cable
to one of the ethernet ports on the device.
Connect the other end to the Ethernet port on a
PC. Note: Use Category 5e or Category 6
Ethernet cables with RJ45 connectors to connect
Ethernet devices to the ethernet ports. This
ensures Ethernet speeds (unless the computer
does not support it).
i Rear Panel Connections and Other
Information
Following are descriptions of the rear panel
connections. Refer to Figure 2.
噝 power: Connect the power adapter. Only use the
power adapter provided with the device.
噝 reset: Insert a pointed object into the opening.
Press for less than10 seconds to power cycle the
Figure 2: Rear Panel Connections
i LED Descriptions and Behaviors
device. Press for more than 10 seconds to reset
the device to the factory defaults.
Following are the descriptions and behaviors of the
LEDs on the front of the device. Refer to Figure 3
LED
COLOR DESCRIPTION
POWER
Green
SYNCH
Green
Blinks quickly–Acquiring IP
address and configuration
file.
Off–Device receives disable
configuration file message.
On–Device has successfully
completed
internal
power ϋon tests. BLINKS if
power ϋon self test fails
WLAN
Indicates the connection
status between the device
and the cable network.
The LED is lit when the
device has established a DS
channel with MSO’s CMTS
(Cable Modem Termination
Equipment)
Ready
Green
WPS
Green
On–At least one wireless
client is linked to the device.
Blinks–Indicates
modem
traffic.
Off–No
wireless
clients
connected.
Green On–WPS used.
Off–WPS not used.
ETHERNET Green
1,2,3,4
or
The LED will flash during
registration process network
On–Ranging
registration
process is successful and the
device is ready to send and
receive data.
On–Connectivity
between
Ethernet ports on the device
and computer:
Orange - Green – 100Mbps
- Orange – 10Mbps
Blinks–Sending or receiving
data.
Note: Sync and Ready LEDs blink during a firmware
upgrade.
Blinks
slowly–Performing
upstream ranging.
540. 00776. 005
Figure 3: Front Panel LEDs
i Wall Mount Installation
Figure 5: Bracket distances
You can mount the device on a wall using the
mounting brackets on the bottom of the device.
Refer to Figure 4. It is recommended to use two
round or pan head screws, not included, as
shown in Figures 5 and 6.
6.65+/-0.35
1.9+/-0.15
19.0+/-1.20
Figure 4: Mounting bracket measurements
2. Remove the device from the product package.
1. Install two screws horizontally apart on a wall
using the measurements shown in Figure 4.
Ensure the screws protrude from the wall to fit the
device between the head of the screw and the
wall. If the screws are installed in drywall, use
hollow wall anchors to ensure the unit does not
pull away from the wall due to prolonged strain
from the cable and power connectors.
3. Mount the device on the wall.
Figure 6: Screw sizes

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2011:09:24 08:47:34+08:00
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Modify Date                     : 2011:11:07 17:47:41+08:00
Metadata Date                   : 2011:11:07 17:47:41+08:00
Producer                        : Acrobat Distiller 9.3.2 (Windows)
Keywords                        : 
Format                          : application/pdf
Creator                         : huangcc
Title                           : 欢迎使用
Description                     : 
Document ID                     : uuid:cabf288a-d982-443a-a9d6-e0f6a3d90ea3
Instance ID                     : uuid:0c2b667d-524b-440f-a008-c16e89f934ac
Subject                         : 164
Company                         : lenovo
Comments                        : 
Source Modified                 : D:20110919104126
Page Count                      : 2
Author                          : huangcc
EXIF Metadata provided by EXIF.tools
FCC ID Filing: XCNDDW262

Navigation menu