Ubee Interactive DVW32C Wireless eMTA User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2441263
Application ID	G/zk4mAkpZ2AXXnYn6fpJA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.37kB (67091 bits)
Date Submitted	2014-11-11 00:00:00
Date Available	2014-11-12 00:00:00
Creation Date	2017-10-20 14:48:28
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-20 14:48:28
Document Title	Microsoft Word - DVW32C Safety_Install_Manual_Insert -2014-11-04-ok.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ChristyFan

Ubee Interactive — www.ubeeinteractive.com
DVW32C Advanced Wireless Voice
Gateway - Safety and Installation
Product Insert
Federal Communications Commission
(FCC) Interference Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one of the
following measures:
 Reorient or relocate the receiving antenna
 Increase the separation
equipment and receiver.
between
the
 Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
 Consult the dealer or an experienced radio/TV
technician for help.
FCC Regulatory Information
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
There is one statement for this product:
 Only the type of PCB PIFA antenna tested
Ubee DVW32CB – Safety and Installation Product Insert v1.0
Ubee Interactive — www.ubeeinteractive.com
may be used.
Devices will not permit operations on channels
120-132 for 11a and 11n/a which overlap the
5600 - 5650 MHz band.
This device and it's antennas(s) must not be
co-located or operating in conjunction with any
other antenna or transmitter except in
accordance with FCC multi-transmitter product
procedures.
FCC Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this equipment.
Safety Notices
For product available in the USA/Canada market,
only channel 1 ~ 11 can be operated. Selection
of other channels is not possible.
For operation within 5.15 ~ 5.25GHz frequency
range, it is restricted to indoor environment.
FCC Radiation Exposure Statement:
This device complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This device should be installed and
operated at a minimum distance of 25cm
between itself and your body.
Read these instructions carefully before
operating the device. It is important to be aware
of these safety instructions. Install the device
according to these instructions and keep this
guide for future reference.
1. Do not use this device in a humid space, in
the rain, or near splashing water.
2. Do not install during thunder or lightning
storms.
3. Do not cover any ventilation openings in the
device case.
4. Do not place the device near heat sources
Ubee DVW32CB – Safety and Installation Product Insert v1.0
Ubee Interactive — www.ubeeinteractive.com
such as radiators or stoves.
5. Clean the device only with a clean, dry cloth.
Do not use liquid or chemical cleaners.
6. Avoid static discharge when touching the
device by first touching the coaxial connector
of the coaxial cable.
7. Installation of the device should include
grounding the coaxial cable to the earth at the
building entrance per ANSI/NFPA 70 and the
National Electrical Code (NEC, in particular,
Section 820.93, Grounding of the Outer
Conductive Shield of a Coaxial Cable). The
device is designed for IT power systems with
phase-to-phase voltage at 90~132VAC.
8. Disconnecting the Device: If the device
becomes damaged or encounters some other
abnormality, disconnect the power plug from
the AC wall outlet immediately.
Fahrenheit).
10. When this device is placed upright with the
aid of the stand, the stand must be fixed at a
90-degree angle to the device. Otherwise, the
device will have the risk of tipping over.
11. Keep the device away from Children and
Pets.
12. Place the device on a cool surface. Failure to
do so may result in overheating which can
cause extreme damage.
13. Do not modify or attempt to disassemble the
device. Use it only according to the
instructions.
14. Do not dispose of the device in a trash
container. Please recycle.
15. This product must be installed upright.
9. The device should be installed in a location
not to exceed the maximum temperature of
40
degrees
Celsius
(104
degrees
Ubee DVW32CB – Safety and Installation Product Insert v1.0
Ubee Interactive — www.ubeeinteractive.com
This ensures Gigabit Ethernet speeds (unless
the computer does not support it).
Installation
To install this device, follow the procedures
below and refer to the following page for a
connection diagram.
1. Connect one end of a coaxial cable (not
included) to the CABLE port on the device.
Connect the other end to a cable splitter or the
cable wall outlet. Be sure not to bend or over
tighten the cables as this may strain the
connector and cause damage. If you plan to
connect the device and a television to the
same cable wall outlet, you must use a cable
line splitter (not included).
3. Connect one end of an RJ-11 phone cable to
one of the TEL ports on the device (a port that
has been provisioned for voice service as
specified by the service provider). Connect the
other end to the phone port of the telephone.
Note: If voice service is not provisioned
through the service provider, telephone
service is not available.
4. Connect the power cord to the POWER port
on the device. Plug the other end of the power
cord into the AC wall outlet. Important: Use
only the power cord that is shipped with the
device.
2. Connect one end of the supplied Ethernet
cable to one of the ETHERNET ports (ETH1
to ETH4) on the device. Connect the other
end to the ETHERNET port on a PC. Note:
Category 5e or Category 6 Ethernet cables
with RJ-45 connectors must be used when
connecting Ethernet devices to the LAN ports.
Ubee DVW32CB – Safety and Installation Product Insert v1.0
Ubee Interactive — www.ubeeinteractive.com
Wall-Mount Installation
163mm (6.4 inches)
You can mount the device on a wall using the 2
mounting brackets on the bottom of the device.
We recommend that you use two round or pan
head screws.
1. Install two screws horizontally apart on a wall
using the measurement shown to the right.
The screws should protrude from the wall so
that you can fit the device between the head
of the screw and the wall. If you install the
screws in drywall, use hollow wall anchors to
ensure that the unit does not pull away from
the wall due to prolonged strain from the cable
and power connectors.
The Distance of the Pothook (Horizontal)
2. Remove the device from the product package.
3. Mount the device on the wall.
4. Refer to the following figure.
The Screw’s Size (mm)
Ubee DVW32CB – Safety and Installation Product Insert v1.0
A 6.65+/-0.35
B 1.9+/-0.15
C 19.0+/1.20
Ubee Interactive — www.ubeeinteractive.com
Additional Information
LEDs and Other Device Indicators
1. RESET Button (back of device): This button
resets the device to factory defaults. Using a
pointed object, insert it into the button opening,
and hold for more than 10 seconds. The
device will reset and reboot. Note: Not all
parameters are reset to factory defaults. Refer
to the User Guide for more information.
See the following diagram and descriptions of the
device’s LED behavior, and the behavior of the
back-panel Ethernet indicators.
2. Battery (bottom of device): A slot is provided
that houses the battery and can be
opened/closed for battery insertion or
replacement.
LED Indicators (Color = Blue When On):
3. WPS button (top of device): The WPS button
is used for the Wi-Fi Protected Setup (WPS)
method to connect a Wi-Fi device to the
DEVICE. Refer to the User Manual for more
information.
Power—If On, indicates that the device has
successfully completed internal power-on tests.
LED flashes if power-on fails. Note that the LED
flashes briefly immediately after powering the
device.
US/DS—When the device initializes, the LED
flashes. When the device locks on to channels
and registers OK, the LED is On. When the
device performs a firmware upgrade, the LED
flashes.
On-line—When the device is obtaining an IP
address and configuration file, the LED flashes.
Ubee DVW32CB – Safety and Installation Product Insert v1.0
Ubee Interactive — www.ubeeinteractive.com
When device obtains these items, the LED is On.
Wi-Fi—When Wi-Fi is enabled, the LED is On.
When Wi-Fi is disabled, the LED is Off.
Tel 1/Tel 2—The LED is On when a telephone is
on-hook. The LED flashes when a telephone is
off-hook.
MoCA— When MoCA is enabled, the LED is On.
When MoCA is disabled, the LED is Off.
When passing MoCA network traffic, the LED is
flash.
Battery—LED is On when the battery is installed
and charged. LED is Off if no battery is installed.
If the battery is at low power level (30mins left),
the battery LED will flash.
Back Panel Ethernet Indicators
(Color = Orange or Green):
 When an Ethernet device, such as a computer,
is connected to the device, the LED is Orange
when connected at 10/100 Mbps speeds.
 When an Ethernet device, such as a computer,
is connected to the device, the LED is Green
when connected at 1000 Mbps speeds
(Gigabit Ethernet).
 When data is being passed between the
device and the connected device, the LED
flashes.
Ubee DVW32CB – Safety and Installation Product Insert v1.0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : ChristyFan
Create Date                     : 2014:11:07 17:04:20+08:00
Modify Date                     : 2014:11:10 13:54:05+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2014:11:10 13:54:05+08:00
Format                          : application/pdf
Title                           : Microsoft Word - DVW32C Safety_Install_Manual_Insert -2014-11-04-ok.doc
Creator                         : ChristyFan
Document ID                     : uuid:e170b81d-0a82-47c4-8dc6-0d4aa90ed532
Instance ID                     : uuid:b6079f7e-4953-4bba-86a6-1ea6a9b5de2e
Page Count                      : 7

EXIF Metadata provided by EXIF.tools