Ubiquiti Networks AF4X Dual Channel OFDM MIMO Point to Point Device User Manual airFiber X User Guide
Ubiquiti Networks, Inc. Dual Channel OFDM MIMO Point to Point Device airFiber X User Guide
Contents
- 1. Users Manual pt 1
- 2. Users Manual pt 2
- 3. Users Manual pt 3
- 4. Users Manual pt 4
- 5. Users Manual pt 5
Users Manual pt 1
![2.4 GHz, 3 GHz, 4 GHz, 5 GHz Carrier Backhaul RadioModel: AF-2X, AF-3X, AF-4X, AF-5X](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-1.png)
![iTable of ContentsairFiber X User GuideUbiquiti Networks, Inc.Table of ContentsChapter 1: Overview ................................................1Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Package Contents ................................................................1airFiber Configuration Interface SystemRequirements ............................1Hardware Overview ..............................................................1Chapter 2: Installation ..............................................3Installation Requirements ........................................................3Installation Overview .............................................................3Connecting Power over Ethernet ..................................................3airFiber Configuration ............................................................4Hardware Installation .............................................................5Alignment .......................................................................9Installer Compliance Responsibility ..............................................10Chapter 3: Navigation .............................................11Accessing the airFiber Configuration Interface ...................................11Product Verification .............................................................12Interface Tabs ...................................................................12Chapter 4: Main Tab ...............................................13Status ...........................................................................13Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Monitor .........................................................................15Chapter 5: Wireless Tab ............................................17Basic Wireless Settings ...........................................................17Frequency Settings ..............................................................19Wireless Security ................................................................19Chapter 6: Network Tab ...........................................21Management Network Settings ..................................................21Chapter 7: Advanced Tab ..........................................23Wireless Settings ................................................................23DATA Port Ethernet Settings .....................................................24MGMT Port Ethernet Settings ....................................................25](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-3.png)
![iiTable of Contents airFiber X User GuideUbiquiti Networks, Inc.Chapter 8: Services Tab ............................................27Ping Watchdog ..................................................................27SNMP Agent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Telnet Server ....................................................................29NTP Client .......................................................................29Dynamic DNS ...................................................................29System Log ......................................................................29Device Discovery ................................................................29Chapter 9: System Tab .............................................31Firmware Update ................................................................31Device ..........................................................................32Date Settings ....................................................................32System Accounts ................................................................32Miscellaneous ...................................................................32Location ........................................................................33Device Maintenance .............................................................33Configuration Management .....................................................33Chapter 10: Tools ..................................................35Align Antenna ...................................................................35Discovery .......................................................................36Ping .............................................................................36Traceroute ......................................................................36airView ..........................................................................36Appendix A: Specifications ........................................41Appendix B: AF-5X and airFiber Multiplexer ........................45airFiber X Compatibility ..........................................................45Installation Requirements .......................................................45Hardware Overview .............................................................45Configure the airFiber 5X Radio ..................................................46Hardware Installation ............................................................46Appendix C: Listen Before Talk .....................................51Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51Unrestricted Protocol Description ................................................51Threshold Detection To Determine Occupancy ...................................51Action Taken When Occupancy is Determined ...................................51Opportunities for Other Transmitters to Operate .................................52](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-4.png)
![iiiTable of ContentsairFiber X User GuideUbiquiti Networks, Inc.Appendix D: Safety Notices ........................................53Electrical Safety Information .....................................................53Appendix E: Warranty .............................................55Limited Warranty ................................................................55Appendix F: Compliance Information ..............................57Installer Compliance Responsibility ..............................................57FCC .............................................................................57Industry Canada .................................................................59RF Exposure Warning ............................................................61Australia and New Zealand ......................................................61CE Marking ......................................................................62airFiber AF-4X Compliance .......................................................62Frequency Ranges and Power Levels per Country/Region ........................63RoHS/WEEE Compliance Statement ..............................................69Appendix G: Declaration of Conformity ............................71Appendix H: Contact Information ..................................73Ubiquiti Networks Support ......................................................73](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-5.png)
![ivTable of Contents airFiber X User GuideUbiquiti Networks, Inc.](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-6.png)
![1Chapter 1: OverviewairFiber X User GuideUbiquiti Networks, Inc.airFiber Configuration Interface SystemRequirements• Microsoft Windows 7, Windows 8; Linux; or Mac OS X• Java Runtime Environment 1.6 (or above)• Web Browser: Mozilla Firefox, Apple Safari, GoogleChrome, Microsoft Edge, or Microsoft Internet Explorer11Hardware OverviewPort CoverLED PanelConnects to External GPS AntennaChain 0: Connects to +45° on airFiber AntennaChain 1: Connects to -45° on airFiber AntennaChapter 1: OverviewIntroductionThank you for purchasing the Ubiquiti Networks® airFiber® X Carrier Backhaul Radio. This User Guide is for use with the following models:Model Description Operating Frequency*AF-2X 2.4 GHz Carrier Backhaul Radio 2400 - 2500 MHzAF-3X 3 GHz Carrier Backhaul Radio 3300 - 3900 MHzAF-4X 4 GHz Carrier Backhaul Radio 4940-4990 MHzAF-5X 5 GHz Carrier Backhaul Radio 5150 - 5925 MHz* Depends on Regulatory Region. Refer to “Specifications” on page 41 for more information.This User Guide provides installation instructions, explains how to set up an airFiber link, and shows how to access and use the airFiber Configuration Interface. Note: Throughout this User Guide, airFiberX radio refers to all models listed above. Unless noted otherwise, illustrations for a specific model are applicable to all airFiberX radio models and accessories.Package ContentsairFiber AF-2X, AF-3X, AF-4X, or AF-5XGPS Antenna Mount External GPS AntennaMetal Strap Cable Ties (Qty. 2) Universal Bracket (AF-4X and AF-5X only)5 GHz Carrier Backhaul RadioModel: AF-5XDATAMGMTGPSLINKDATAMGMTGPSLINKairFiber PoE (24V, 1A) with Mounting BracketPower Cord Quick Start GuideTERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is designed for outdoor installations. It is the customer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements.](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-7.png)
![2Chapter 1: Overview airFiber X User GuideUbiquiti Networks, Inc.PortsReset ButtonManagement PortData PortManagement Port 10/100 Mbps, secured Ethernet port for configuration. In-Band Management is enabled by default in the airFiber Configuration Interface. When In-Band Management is disabled, the MGMT port is the only port that can monitor, configure, and/or update firmware.Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is already poweredon.Data Port Gigabit PoE port for handling all user traffic and powering the device.LEDsSignal LEDsSignal 4 LED will light blue when on.Signal 3 LED will light green when on.Signal 2 LED will light yellow when on.Signal 1 LED will light red when on.Bootup to airOS When powering on, the Power, GPS, LINK, and Signal 1-4 LEDs light on. Once the CPU code takes over, the GPS, LINK, and Signal 1-3 LEDs turn off. Signal 4 LED remains on to indicate the boot sequence is underway.Initializing airFiber Software When the airFiber application begins to boot under airOS, the Signal 4 LED goes from solidly on to a 2.5 Hz flash. This continues until the airFiberX radio is fully booted.Signal Level Once fully booted, the Signal 1-4 LEDs act as a bar graph showing how close the airFiberX radio is to ideal aiming. This is auto-scaled based on the link range, the antenna gains, and the configured TX power of the remote airFiberX radio. Each Signal LED has three possible states: On, Flashing, and Off. All Signal LEDs would be solidly on in an ideal link. If the link has a 1 dB loss, the Signal4 LED will flash; a 2 dB loss and the Signal 4 LED will turn off. The full bar graph LED states are shown below.dB loss 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -131 F 0 0 0 0 0 0 0 0 0 0 0 01 1 1 F 0 0 0 0 0 0 0 0 0 01 1 1 1 1 F F 0 0 0 0 0 0 01111111111 F F F 00 = Off, 1 = On, F = FlashingAdditional LEDsLED State StatusLINKOff RF OffShort Flash* SyncingNormal Flash* BeaconingLong Flash* RegisteringOn OperationalGPSOff No GPS SynchronizationNormal Flash* Non-Operational (Weak Signal) On Operational (Strong Signal)MGMTOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flashing Ethernet ActivityDATAOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flashing Ethernet Activity Off No PowerOn Powered On* Short Flash (1:3 on/off cycle) Normal Flash (1:1 on/off cycle) Long Flash (3:1 on/off cycle)](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-8.png)
![3Chapter 2: InstallationairFiber X User GuideUbiquiti Networks, Inc.Chapter 2: InstallationInstallation RequirementsThe airFiberradio operates only with the antennas listed below:airFiberRadio airFiberX Antenna RocketDish + Conversion KitAF-2X AF-2G24-S45 n/aAF-3X AF-3G26-S45 n/aAF-4X AF-5G30-S45 AF-5G34-S45RD-5G30 + AF-5G-OMT-S45RD-5G34 + AF-5G-OMT-S45AF-5XAF-5G23-S45AF-5G30-S45AF-5G34-S45RD-5G30 + AF-5G-OMT-S45RD-5G34 + AF-5G-OMT-S45See the antenna’s Quick Start Guide for antenna installation instructions. Other Requirements• Clear line of sight between airFiberX radios• Clear view of the sky for proper GPS operation• Vertical mounting orientation• Mounting point:• At least 1 m below the highest point on the structure• For tower installations, at least 3 m below the top of thetower• Ground wires – min. 10 AWG (5 mm2) and max. length: 1m. Asa safety precaution, ground the airFiberX radio to grounded masts, poles, towers, or grounding bars. WARNING: Failure to properly ground your airFiberX radio will void your warranty. • (Recommended) 2 Outdoor Gigabit PoE surge protectorsNote: For guidelines about grounding and lightning protection, follow your local electrical regulatory codes. • Outdoor, shielded Category 6 (or above) cabling and shielded RJ-45 connectors are required for all wired Ethernet connections.Installation OverviewWe recommend to configure your paired airFiberX radios before site installation. The overview below summarizes the installation procedure, and the subsequent sections provide detailed installation information:• Connect the airFiber PoE Adapter to the DATA port, and connect your computer and the MGMTport.• Configure the airFiberX radio.• Install a ground wire and mount the airFiberX radio on an airFiberX antenna.• At the installation site, install the airFiberX antenna with the mounted airFiberX radio (see the antenna’s Quick Start Guide for installation instructions).• Secure the ground wire and mount the GPS antenna.• Establish and optimize the RF link.Connecting Power over Ethernet1. Lift the release latch on the bottom of the airFiberX radio and slide the Port Cover off.2. Connect an Ethernet cable to the DATA port.3. Connect the Ethernet cable from the DATA port to the Ethernet port labeled POE on the airFiber PoE Adapter.WARNING: Use only the included airFiber PoE adapter, Model GP-H240-100G-4. Failure to do so can damage the unit and void the product warranty.](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-9.png)
![4Chapter 2: Installation airFiber X User GuideUbiquiti Networks, Inc.4. Connect the Power Cord to the power port on the airFiber PoE Adapter. Connect the other end of the Power Cord to a powersource.airFiber ConfigurationThe instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings: • Wireless Mode Configure one airFiberX radio as the Master and the other as the Slave.• Frequency Setting The operating Frequency must be the same on both the Master and the Slave.1. Connect an Ethernet cable from your computer to the MGMT port on the airFiberX radio.2. Configure the Ethernet adapter on your computer with a static IP address on the 192.168.1.x subnet.3. Launch your web browser. Type http://192.168.1.20 in the address field and press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.Note for models AF-2X, AF-3X, and AF-5X only: U.S. product versions are locked to the U.S. Country Code to ensure compliance with FCC regulations. 5. Click the Wireless tab.6. Configure the Basic Wireless Settings:a. For one airFiberX radio, select Master as the Wireless Mode. For the other airFiberX radio, keep the default,Slave.b. Enter a name in the Link Name field. This should be the same on both the Master and the Slave.c. If needed, change the Channel Bandwidth, (Master) Duty Cycle, Output Power, Cable Loss (see Note below), and/or Maximum Modulation Rate settings.Note: If you are using the airFiber AF-5X radio with an airFiber Multiplexer, perform the following additional steps:d. Set the CableLoss to a value that includes the additional loss (in dB) due to the Multiplexer. The additional cable loss is (approximately):• 4 dB for the AF-MPx4, or• 7 dB for the AF-MPx8e. Enable the NxN Radio setting on each end of the link.](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-10.png)
![5Chapter 2: InstallationairFiber X User GuideUbiquiti Networks, Inc.7. Configure the Frequency Settings. The selected Frequency must be the same on both airFiberX radios.8. Configure the Wireless Security: a. Select the AES Key Type, HEX or ASCII.b. For the Key field: -HEX Enter 16 bytes (eight, 16-bit HEX values: 0-9, A-F, or a-f ). You can omit zeroes and use colons, similar to the IPv6 format.Note: The airFiber Configuration Interface supports IPv6 formats excluding dotted quad and “::” (double-colon) notation. -ASCII Enter a combination of alphanumeric characters (0-9, A-Z, or a-z).9. Click Change and then click Apply.10. In-Band Management is enabled by default, so each airFiberX radio must have a unique IP Address. (If the airFiberX radios use the same IP Address, you may lose access to the airFiberX radios via the DATA ports.) Click the Network tab.a. For the Management IP Address option: -DHCP Keep the default, DHCP, to use DHCP reservation on your router to assign a unique IPAddress. -Static Change the IP Address, Netmask, and other settings to make them compatible with your network.b. Click Change and then click Apply.Repeat the instructions in the airFiber Configuration section on your other airFiberX radio. After you have configured the airFiberX radios, disconnect them and move them to your installation site.Hardware InstallationInstall a Ground Wire1. Remove the nut from the Ground Bonding Point located on the back of the airFiberX radio.Ground Bonding Point2. Attach a ground wire (min. 10 AWG or 5 mm2) to the lug and replace the nut to secure the wire.3. At the installation site, secure the other end of the ground wire to a grounded mast, pole, tower, or grounding bar.WARNING: Failure to properly ground your airFiberX radio will void your warranty. Note: The ground wire should be as short as possible and no longer than one meter in length.](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-11.png)
![6Chapter 2: Installation airFiber X User GuideUbiquiti Networks, Inc.Mount to an AntennaThe airFiberX radio can be mounted to the antenna(s) listed in “Installation Requirements” on page 3. The airFiberX Antenna (AF-5G30-S45) is shown in the following steps:1. Attach the airFiber X radio to the antenna by aligning the four tabs on the back of the radio with the slots of the radio mount. Then slide the radio down to lock it into place.2. Attach the RF connectors to the radio in this combination: +45°to Chain 0 and -45° to Chain 1. Thenslide the jackets over the RF connectors to protectthem.3. Attach the External GPS Antenna (included with the radio) to the RF connector labeled GPS on the radio.4. Attach the protective shroud. a. Align the hash mark on the top of the shroud with the notch on the dish antenna. b. Rotate the shroud clockwise until it locks into place.](https://usermanual.wiki/Ubiquiti-Networks/AF4X.Users-Manual-pt-1/User-Guide-2963298-Page-12.png)