Ubiquiti AF3X Digital Point-to-Point Radio User Manual airFiber AF 3X Quick Start Guide

Ubiquiti Networks, Inc. Digital Point-to-Point Radio airFiber AF 3X Quick Start Guide

User manual

3 GHz Carrier Backhaul RadioModel: AF-3XDATAMGMTGPSLINKDATAMGMTGPSLINK
IntroductionThank you for purchasing the Ubiquiti Networks® airFiber® 3GHz Carrier Backhaul Radio. This Quick Start Guide is designed to guide you through the installation, show you how to access the airFiber Configuration Interface, and explain how to set up an airFiber link. This Quick Start Guide is for use with the airFiber AF-3X. Warranty terms, safety notices, and compliance information are in the airFiber AF-3X User Guide, available at: downloads.ubnt.comPackage ContentsDATAMGMTGPSLINKairFiber AF-3X GPS Antenna Mount External GPS AntennaMetal Strap3 GHz Carrier Backhaul RadioModel: AF-3XDATAMGMTGPSLINKDATAMGMTGPSLINKCable Ties (Qty. 2)airFiber PoE Adapter with Mounting Bracket (24V, 1A)Power Cord Quick Start GuideTERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is designed for outdoor installations. It is the customer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements.
Installation RequirementsThe airFiber AF-3X radio is designed for use with the airFiber X AF-3G26-S45 antenna.Other Requirements• Clear line of sight between airFiber radios• Clear view of the sky for proper GPS operation• Vertical mounting orientation• Mounting point:• At least 1 m below the highest point on the structure• For tower installations, at least 3 m below the top of thetower• Ground wires – min. 10 AWG (5 mm2) and max. length: 1m. Asa safety precaution, ground the airFiber radio to grounded masts, poles, towers, or grounding bars. WARNING: Failure to properly ground your airFiber radio will void your warranty.• (Recommended) 2 Outdoor Gigabit PoE surge protectorsNote: For guidelines about grounding and lightning protection, follow your local electrical regulatory codes.• Outdoor, shielded Category 6 (or above) cabling and shielded RJ-45 connectors are required for all wired Ethernet connections.
Hardware OverviewDATAMGMTGPSLINKPort CoverLEDPanelConnects toExternal GPS Antenna Chain 1: Connects to- 45° on airFiber AntennaChain 0: Connects to+ 45° on airFiber Antenna
PortsReset ButtonManagement PortData PortManagement Port 10/100 Mbps, secured Ethernet port for configuration. In-Band Management is enabled by default in the airFiber Configuration Interface. When In-Band Management is disabled, the MGMT port is the only port that can monitor, configure, and/or update firmware.Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is already poweredon.Data Port Gigabit PoE port for handling all user traffic and powering the device.
LEDsSignal LEDsSignal 4 LED will light blue when on.Signal 3 LED will light green when on.Signal 2 LED will light yellow when on.Signal 1 LED will light red when on.Bootup to airOS When powering on, the Power, GPS, LINK, and Signal 1-4 LEDs light on. Once the CPU code takes over, the GPS, LINK, and Signal 1-3 LEDs turn off. Signal 4 LED remains on to indicate the boot sequence is underway.Initializing airFiber Software When the airFiber application begins to boot under airOS, the Signal 4 LED goes from solidly on to a 2.5 Hz flash. This continues until the AF-3X is fully booted.Signal Level Once fully booted, the Signal 1-4 LEDs act as a bar graph showing how close the AF-3X is to ideal aiming. This is auto-scaled based on the link range, the antenna gains, and the configured TX power of the remote AF-3X. Each Signal LED has three possible states: On, Flashing, and Off. All Signal LEDs would be solidly on in an ideal link. If the link has a 1 dB loss, the Signal4 LED will flash; a 2 dB loss and the Signal 4 LED will turn off. The full bar graph LED states are shown below.dB loss 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -131F000000000000111F000000000011111F F 00000001111111111FFF00 = Off, 1 = On, F = Flashing
Additional LEDsLED State StatusLINK Off RF OffShort Flash* SyncingNormal Flash* BeaconingLong Flash* RegisteringOn OperationalGPSOff No GPS SynchronizationNormal Flash* Non-Operational (Weak Signal) On Operational (Strong Signal)MGMTOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flashing Ethernet ActivityDATAOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flashing Ethernet Activity Off No PowerOn Powered On* Short Flash (1:3 on/off cycle) Normal Flash (1:1 on/off cycle) Long Flash (3:1 on/off cycle)
Installation OverviewWe recommend that you configure your paired AF-3X radios before site installation. The overview below summarizes the installation procedure, and the subsequent sections provide detailed installation information. • Connect the airFiber PoE Adapter to the DATA port, and connect your computer to the MGMTport.• Configure the AF-3X.• Install a ground wire and mount the AF-3X on an airFiber X antenna.• At the installation site, install the airFiber X antenna with the mounted AF-3X radio (see the antenna’s Quick Start Guide for installation instructions).• Secure the ground wire and mount the GPS antenna.• Establish and optimize the RF link.Connecting Power over Ethernet1. Lift the release latch on the bottom of the AF-3X and slide the Port Cover off.
2. Connect an Ethernet cable to the DATA port.3. Connect the Ethernet cable from the DATA port to the Ethernet port labeled POE on the airFiber PoE Adapter.WARNING: Use only the included airFiber PoE Adapter, Model: GP-H240-100G-4. Failure to do so can damage the unit and void the product warranty.4. Connect the Power Cord to the power port on the airFiber PoE Adapter. Connect the other end of the Power Cord to a powersource.
airFiber ConfigurationThe instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings: • Wireless Mode Configure one AF-3X as the Master and the other as the Slave.• Frequency Setting The operating Frequency must be the same on both the Master and the Slave.1. Connect an Ethernet cable from your computer to the MGMT port on the AF-3X.2. Configure the Ethernet adapter on your computer with a static IP address on the 192.168.1.x subnet.3. Launch your web browser. Type http://192.168.1.20 in the address field and press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.Note: U.S. product versions are locked to the U.S. Country Code to ensure compliance with FCC regulations. 5. The Main tab will appear. Click the Tools drop-down and select Link Calculator. This tool will guide you on how to best minimize bandwidth and power/interference issues.6. Enter the requirements of your link, and then click Calculate. Adjust the values as needed to get the optimal result, and then write down the settings needed for your configuration.7. Click the Wireless tab.
8. Configure the Basic Wireless Settings:a. For one AF-3X, select Master as the Wireless Mode. For the other AF-3X, keep the default,Slave.b. Enter a name in the Link Name field. This should be the same on both the Master and the Slave.c. If needed, change the Channel Bandwidth, (Master) Duty Cycle, Output Power and/or Maximum Modulation Rate settings.9. Configure the Frequency Setting. The selected Frequency must be the same on both airFiber radios.10. Configure the Wireless Security: a. Select the AES Key Type, HEX or ASCII.b. For the Key field: - HEX Enter 16 bytes (eight, 16-bit HEX values: 0-9, A-F, or a-f). You can omit zeroes and use colons, similar to the IPv6 format.Note: The airFiber Configuration Interface supports IPv6 formats excluding dotted quad and “::” (double-colon) notation. - ASCII Enter a combination of alphanumeric characters (0-9, A-Z, or a-z).11. Click Change and then click Apply.
12. In-Band Management is enabled by default, so each airFiber radio must have a unique IP Address. (If the airFiber radios use the same IP Address, you may lose access to the airFiber radios via the DATA ports.) Click the Network tab.a. For the Management IP Address option: - DHCP Keep the default, DHCP, to use DHCP reservation on your router to assign a unique IPAddress. - Static Change the IP Address, Netmask, and other settings to make them compatible with your network.b. Click Change and then click Apply.Repeat the instructions in the airFiber Configuration section on the other AF-3X radio.For details on the airFiber Configuration Interface, refer to the airFiber AF-3X User Guide, available at: downloads.ubnt.com
Hardware InstallationInstall a Ground Wire1. Remove the nut from the Ground Bonding Point located on the back of the AF-3X.Ground Bonding Point2. Attach a ground wire (min. 10 AWG or 5 mm2) to the lug and replace the nut to secure the wire.3. At the installation site, secure the other end of the ground wire to a grounded mast, pole, tower, or grounding bar.WARNING: Failure to properly ground your airFiber radio will void your warranty.Note: The ground wire should be as short as possible and no longer than one meter in length.*640-00197-01*640-00197-01
Mount to the airFiber X Antenna1. Attach the AF-3X to the mounting bracket. a. Align the mounting tabs on the back of the AF-3X with the mounting bracket.b. Slide the AF-3X down to lock it into place.
2. Attach the RF cables from the antenna feed to the RF connectors on the AF-3X in this combination: + 45° to Chain0 and - 45° to Chain 1.3. Attach the External GPS Antenna to the RF connector labeled GPS. Then place the magnetic External GPS Antenna on the bracket (this is temporary; you will mount the External GPS Antenna on the GPS Antenna Mount at the site).
4. Attach the protective shroud. a. Align the hash mark on the top of the shroud with the notch on the dish antenna. b. Rotate the shroud clockwise until it locks into place.
Mount the External GPS AntennaLocate a mounting point that has a clear view to the sky, and is above and as far away as possible from the AF-3X.1. Attach the GPS Antenna Mount to the pole using the metal strap, or attach it to a wall using the appropriate fasteners (notincluded).2. Place the External GPS Antenna on the mount.3. Secure the cable of the External GPS Antenna to the mount with a Cable Tie.
Connecting Power over Ethernet1. Lift the release latch on the bottom of the AF-3X and slide the Port Cover off. 2. Connect an outdoor, shielded Ethernet cable to the DATAport.
3. Connect the other end of the cable from the DATA port to the Ethernet port labeled POE on the airFiber PoE Adapter.WARNING: Use only the included airFiber PoE Adapter, Model: GP-H240-100G-4. Failure to do so can damage the unit and void the product warranty.4. Connect an Ethernet cable from your network to the Ethernet port labeled LAN on the airFiber PoE Adapter.5. Connect the Power Cord to the power port on the airFiber PoE Adapter. Connect the other end of the Power Cord to a power source.
Mount the PoE Adapter (Optional)1. Remove the Mounting Bracket from the adapter by sliding the bracket downward.2. Place the Mounting Bracket at the desired location and mark the holes for the fasteners. Pre-drill the holes if necessary, then secure the bracket to the wall using two fasteners (not included). 3. Attach the airFiber PoE Adapter to the bracket by aligning the four slots and tabs, and then slide the adapter downward.
Surge ProtectionFor added protection, install two surge suppressors, such as the Ubiquiti Ethernet Surge Protector, model ETH-SP, at the end of each link. Install the first surge protector within one meter of the airFiber DATA port, and install the second surge protector at the ingress point of the location housing the wired network equipment.Ground to Pole, Tower,or Grounding Block:Max. 1 m from AF-3XMax. 1 mairFiberPoE AdapterEdgeRouter™Power SourceETH-SPGPS AntennaETH-SPAF-3XMounted onAF-3G26-S45
AlignmentTips• To accurately align the airFiber radios for best performance, you MUST align only one end of the link at a time.• You may need to use additional hardware to compensate for issues such as the improper orientation of a mounting pole or significant elevation differences between airFiber radios.Establishing a LinkAdjust the positions of the Master and the Slave to establish a link. Note: The Master must be aimed first at the Slave because the Slave does not transmit any RF signal until it detects transmissions from the Master.1. Master Visually aim the Master at the Slave. To adjust the Master’s position:a. Loosen the four pole clamp nuts, and rotate the airFiber antenna on the pole to align the azimuth.
b. Loosen the six elevation bolts, and use the hex nut on the elevation rod to adjust the elevation.Note: Do NOT make simultaneous adjustments on the Master and Slave.2. Slave Visually aim the Slave at the Master. To adjust the Slave’s position:a. Loosen the four pole clamp nuts, and rotate the airFiber antenna on the pole to align the azimuth.b. Loosen the six elevation bolts, and use the hex nut on the elevation rod to adjust the elevation.3. Check to see if a link is established. Ensure that the LINK LED is solidly lit green and the Signal LEDs of the Slave are displaying signal levels.
4. Slave Aim the Slave at the Master to achieve the strongest signal level on the Master.Note: Refer to the Signal LEDs section for details on the signal values.Note: Maximum signal strength can best be achieved by iteratively sweeping through both azimuth and elevation.5. Master Aim the Master at the Slave to achieve the strongest signal level on the Slave.6. Repeat steps 4 and 5 until you achieve an optimal link, with all four Signal LEDs solidly lit. This ensures the best possible data rate between the airFiber radios.7. Lock the alignment on both airFiber antennas by tightening all the nuts and bolts.8. Observe the Signal LEDs of each airFiber radio to ensure that the values remain constant while tightening the nuts and bolts. If any LED value changes during the locking process, loosen the nuts and bolts, finalize the alignment of each airFiber antenna again, and retighten the nuts and bolts.
Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements.The Output Power, Antenna Gain, Cable Loss, and Frequency fields are provided to the professional installer to assist in meeting regulatory requirements.
SpecificationsairFiber AF-3XDimensions 224 x 82 x 48 mm (8.82 x 3.23 x 1.89")Weight 0.35 kg (0.77 lb)RF Connectors (2) RP-SMA Weatherproof (CH0, CH1)(1) SMA Weatherproof (GPS)GPS Antenna External, Magnetic BasePower Supply 24V, 1A PoE Gigabit Adapter (Included)Power Method Passive Power over Ethernet Mounting Rocket Mount CompatibleGPS Pole Mount (Included)Certications FCC Part 90 ZCE EN 302 217-2-2 Operating Temperature -40 to 55° C (-40 to 131° F)Networking InterfaceData Port (1) 10/100/1000 Ethernet PortManagement Port (1) 10/100 Ethernet PortSystemMaximum Throughput 500 MbpsEncryption 128-bit AESOS airOS FWireless Modes Master/SlaveRadioOperating Frequency 3300-3900 MHz (Depends on Regulatory Region)Max. Conducted TX Power 29 dBm (Depends on Regulatory Region)Frequency Accuracy ± 2.5 ppm without GPS Synchronization± 0.2 ppm with GPS SynchronizationChannel Bandwidth 10/20/30/40/50 MHz Selectable Programmable Uplink and Downlink Duty Cycles
Online ResourcesSupport support.ubnt.comCommunity community.ubnt.comDownloads downloads.ubnt.com© 2015 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, UbiquitiNetworks, the UbiquitiU logo, the Ubiquiti beam logo, airFiber, airOS, RocketDish, and TOUGHCable are trademarks or registered trademarks of UbiquitiNetworks,Inc. in the United States and inother countries. All other trademarks are the property of their respective owners. RR051115

Navigation menu