Ubiquiti PBE5M Access Point User Manual PowerBeam PBE M5 620 Quick Start Guide

Ubiquiti Networks, Inc. Access Point PowerBeam PBE M5 620 Quick Start Guide

Manual 620 part2

10. Attach the Stabilizer Brackets to the pole just beneath the area where the PowerBeam will be attached.Note: The pole-bracket assembly can accommodate a Ø 38 - 101mm pole.a.  Place one Stabilizer Bracket on each side of the pole.b.  Insert the two M10x100 Bolts into the Stabilizer Brackets.c.  Secure each bolt with one Serrated Flange Nut.50 N-m
11. Attach the pole-bracket assembly to the pole:a.  Slide the slot of each Pole Clamp over the corresponding M8x150 CarriageBolt.b.  Tighten the serrated flange nuts of the bolts to secure the pole-bracket assembly to the pole.Proper slot orientation25 N-m
12. Lift the Dish Reflector and align the two lower Hex Head Bolts with the slots on the Lower Pole Bracket. Seat the bolts in the slots.13. Attach each arm of the Upper Pole Bracket to the Mounting Bracket using a Hex Head Bolt, Lock Washer, and Flat Washer.
14. Before adjusting the tilt angle, ensure that the six Hex Head Bolts are loose enough to allow movement.IMPORTANT: If you cannot spin the washers freely by hand, then loosen the Hex Head Bolts until you can.15. To adjust the tilt angle, turn the screw head of the elevation rod until the desired tilt is reached.16. Lock the alignment by tightening all six FlangeBolts to 25 N-m.
17. Connect the other end of the Ethernet cable from the PowerBeam to the Ethernet port labeled POE on the Gigabit PoEAdapter.18. Connect an Ethernet cable from your LAN or computer to the Ethernet port labeled LAN on the adapter.19. Connect the Power Cord to the power port on the adapter. Connect the other end of the Power Cord to a power outlet.*640-00147-04*640-00147-04
Mounting the PoE Adapter (Optional)1.  Slide the PoE Mounting Bracket down to remove it from the Gigabit PoE Adapter.2.  Place the PoE Mounting Bracket at the desired location and mark the two holes. Pre-drill the holes if necessary, and then secure the bracket using two fasteners (not included).3.  Align the slots of the Gigabit PoE Adapter with the tabs of the PoE Mounting Bracket, and then slide the adapterdown.
Accessing airOSVerify connectivity in the airOS Configuration Interface. 1.  Make sure that your host system is connected via Ethernet to the PowerBeam. 2.  Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.3.  Launch your web browser and type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac). 4.  The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.Note: U.S. product versions are locked to the U.S. Country Code to ensure compliance with FCCregulations. The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For details, refer to the User Guide available at documentation.ubnt.com/airmax
Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements.
SpecificationsPowerBeam PBE-M5-620Dimensions 650 x 650 x 386 mm (25.6 x 25.6 x 15.2")Weight 6.4 kg (14.11 lb)Operating Frequency Worldwide: 5150 - 5875 MHz USA: 5150-5250, 5725 - 5850 MHzGain 29 dBiNetworking Interface (1) 10/100/1000 Ethernet PortEnclosure Outdoor UV Stabilized PlasticMax. Power Consumption 8.5WPower Supply 24V, 0.5A Gigabit PoE Supply (Included)Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)Wind Survivability 200 km/h (125 mph)Wind Loading 872 N @200 km/h (196 lbf @125 mph)Certications CE, FCC, ICMounting Pole Mounting Kit IncludedOperating Temperature -40 to 70° C (-40 to 158° F)Operating Humidity 5 to 95% NoncondensingShock and Vibrations ETSI300-019-1.4

Navigation menu