Ubiquiti SMPICO Solar Pico User Manual part 1

Ubiquiti Networks, Inc. Solar Pico part 1

Contents

User manual part 1

Download: Ubiquiti SMPICO Solar Pico User Manual part 1
Mirror Download [FCC.gov]Ubiquiti SMPICO Solar Pico User Manual part 1
Document ID2951837
Application IDMjSXpGcBAQ5+vMefiyB1Pg==
Document DescriptionUser manual part 1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize297.13kB (3714092 bits)
Date Submitted2016-04-06 00:00:00
Date Available2016-10-03 00:00:00
Creation Date2017-11-23 03:41:22
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-23 03:41:22
Document TitleUser manual part 1
Document Creatorpdfsam-console (Ver. 2.4.3e)

"U
UBIQUITF
NETWORKS
\\1,
sllilXw
Solar Gateway -"
Model: SM-PICO QUICK START GUIDE
Introduction
Thank you for purchasing the Ubiquiti Networks® sunMAX”
Solar Gateway Picom. This Quick Start Guide is designed to
guide you through the installation and setup of this product,
and also includes safety instructions and warranty terms.
Package Contents
“WM“
Solar Gateway Antenna Mounting Screws
Pico Bracket (M3.5x14, Qty. 2)
PoE Adapter PoE Mounting airGateway Power Cord
Bracket
N l
Zip Tie Small AC Large AC Quick Start
Disconnect Tool Disconnect Tool Guide
Note: The AC Disconnect Tools are not used to install the
Solar Gateway Pico. They are included to disconnect the
AC connectors used in the sunMAX system.
Hardware Overview
Ports
Ethernet Port RESEI‘ Button
! a
v m in
Er El .
I Egg“ I
i ,
Ethernet Port The Ethernet Port connects to the PoE
port on the airGateway or PoE Adapter to power on the
Solar Gateway Pico.
Reset Button The Reset Button resets the Solar Gateway Pico.
To restore the Solar Gateway Pico to factory defaults, press
and hold the Reset Button for more than 10 seconds while the
device is powered on.
LEDs
GOCD*Q
Inverter Lights up steady green when all of
the Microinverters are operating properly and
communicating with the Solar Gateway Pico.
Bluetooth Lights up steady green when the
Microinverters are active and flashes when there
is activity.
Cloud Lights up steady green when the
Solar Gateway Pico has established a connection
to the cloud server.
Network Lights up steady green when the
Solar Gateway Pico establishes an Ethernet link.
Boot Status Lights up steady green upon bootup
and flashes during a firmware update or other
system activity.
Power Lights up steady green when the
Solar Gateway Pico is powered on.
Antenna Installation
Connect the Antenna to the RP-SMA connector on the
Solar Gateway Pico and rotate it clockwise until it stops.
GL‘QD-'W
Setting Up the Solar Gateway Pico
The sunMAXInsta/l app allows you to set up the Solar Gateway
Pico on your network to manage and gather real—time
information about your solar array system.
1. On your mobile device, download the sunMAXInsta/I app
for Android“ from the Google Play“ Store.
2. Launch the sunMAXInsta/I app and type your username
and password into their corresponding fields. These
credentials are created when you register online at
https://account.ubnt.com/Iogin
3. Tap Sign In to sign in to the mobile app.
MAX install
4. Tap a customer name from the list of sites installed.
5. When the Site Dashboard screen appears, tap Gateway.
6. When prompted for a connection type to your local
network, tap Ethernet for a wired connection or
airGateway to use Wi—Fi to connect to your LAN.
Proceed to the section that corresponds to your selection.
Ethernet
1. Connect the Solar Gateway Pico by performing steps a-c.
Tap Next when done.
a. Remove the Port Cover from the Solar Gateway Pico,
connect an Ethernet cable, and replace the port cover.
cw: "W“ ‘ ’
_|n
» 4 ll "1 1“ > ‘
b— ‘ u"- 4 ‘ I
Port Cover 1
640—00222—02
b. Connect the other end of the Ethernet cable to the PoE
port on the PoEAdapter. Ensure that the PoEAdapter is
plugged into a power source.
c. Connect an Ethernet cable from your local area network
to the LAN port on the PoEAdapter.
2. Tap Scan QR to pair the Solar Gateway Pico with the
current customer site information.
3. Scan the Gateway QR code to complete the pairing
process.
4. When the MAC address screen appears, tap Next to
continue or Redo Scan if necessary.
5. The following screen appears while the Solar Gateway Pico
is connecting to your network and being configured.
6. Tap Done to complete the installation.
‘u’fl'ur ”mm-m.
Success'
luv-mm m mm",
Once the Solar Gateway Pico has been set up and connected
to your home network, return to the Dashboard screen to
verify that the Gateway status icon is solid blue.
Setup is now complete.
Note: It may take up to five minutes for the Solar
Gateway Pico to register with the cloud and update the
status of the Gateway.
airGateway
1. Tap Scan QR to pair the Solar Gateway Pico with the
current customer site information.
2. Scan the QR code on the Solar Gateway Pico to complete
the pairing process.
3. When the MAC address screen appears, tap Next to
continue or Redo Scan if necessary.
4. Remove the Port Cover from the Solar Gateway Pico,
connect an Ethernet cable, and replace the port cover.
a)
U n]
T w
| i may; , l
Eh.
Port Cover
5. Connect the airGateway to the PoE port on the PoEAdapter
and tap Next.
\ flflnnr" umPW-W
Connect solavGaleway
6. Connect the Ethernet port from the Solar Gateway Pico
to the PoE port on the airGateway and connect the power
cord. Tap Next when you are finished.
\ nrmnm mummy
Power me auGateway
7. Wait for a list of discovered wireless networks to appear
and make your selection.
‘Sfllétl 3 Network
NHGEAR! 3
8. Type your password in the Password field and tap Country
to select your country. When you are finished, tap Connect.
9. Once the Solar Gateway Pico has connected to your
network, tap Done to complete the installation.
“mu;- ”mm-m.
Success'
“mm m mm,”
Once the Solar Gateway Pico has been set up and connected
to your home network, return to the Dashboard screen to
verify that the Gateway status icon is solid blue.
Note: It may take up to five minutes for the Solar
Gateway Pico to register with the cloud and update the
status of the Gateway.
Mounting the Solar Gateway Pico
Note: The Solar Gateway Pico must be installed within a
50—foot range of all Microinverters in your solar array.
Wall Mount
1. Secure the mounting bracket vertically to a wall or flat
surface using the two Screws.
2. Insert the Solar Gateway Pico into the mounting bracket
and slide it down until it snaps into place.
Pole Mount
1. Insert the Zip Tie through the bracket on the Solar Gateway
Pico.
2. Place the Solar Gateway Pico against the pole at the
desired height.
3. Fasten the Zip Tie to the pole until the Solar Gateway Pico
is secure.
‘D
Mounting the PoE Adapter (Optional)
1. Slide the PoEMounting Bracket down to remove it from the
PoE Adapter.
2. Place the PoE Mounting Bracket at the desired location
and use it as a template to mark the hole location for each
mounting screw. Use both mounting screws to secure the
PoE Mounting Bracket in place.
i J
3. Line up the notches on the PoEAdapter with the tabs on
the PoE Mounting Bracket. Push the PoE Adapter into place
on the bracket and slide it down until it is secure.
For more information on sunMAX installations, please refer
to the sunMAX User Guide, which is available online at:
documentation.ubnt.com/sunmax
Specifications
sunMAX Solar Gateway Pico
Dimensions 153 x 40 x 37.4 mm (6.02 x 1.57 x1.47")
Weight 79 g (0.17 lb)
Enclosure Characteristics Polycarbonate, UV—Resistant
Processor MediaTek SoC
Memory 256 MB
Storage 1 GB Flash
Networking Interface (1) 10/100/1000 Mbps RJ45 Ethernet Port
Bluetooth Low-Power BLE, Bluetooth v4.1
LEDs 6 LEDs: Power, Status, Ethernet, Cloud,
BLE, Inverter Connectivity
Button Factory Reset Button
clcmszlon (HW) SW
Power Source PoE
Power Supply 24V / 0.5A
ESD/EMP Protection 1 24kV Contact
Shock and Vibration IEC 68—2—6
Operating Temperature -20 to 50° C (-4 to 122° F)
Operating Humidity 5 to 95% Noncondensing
Certifications FCC, CE, IC, UL
Safety Notices
1.
2.
3.
Read, follow, and keep these instructions.
Heed all warnings.
Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in locations that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1.
Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a.
Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2—wire
outlet as this will defeat the continuity of the grounding wire.
The equipment requires the use of the ground wire as a part ofthe
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
Protective bonding must be installed in accordance with local
national wiring rules and regulations.
Limited Warranty
UBIQUITI NETWORKS, Inc (”UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the ”Product(s)") shall be free from defects
in material and workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,
to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period ofany repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the product:
(I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal physical,
electromagnetic or electrical stress, including lightning strikes, or
accident;
(V) has been damaged or impaired as a result of using third party
firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti Iabel(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA.
In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling
runs use CATS (or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling requirements
are followed.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2016:03:28 16:31:53+08:00
Creator                         : pdfsam-console (Ver. 2.4.3e)
Modify Date                     : 2016:03:28 16:32:30+08:00
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Creator Tool                    : pdfsam-console (Ver. 2.4.3e)
Metadata Date                   : 2016:03:28 16:32:30+08:00
Producer                        : iText 2.1.7 by 1T3XT
Format                          : application/pdf
Document ID                     : uuid:bbee1f99-6c3a-4b71-b85d-2d05502768f5
Instance ID                     : uuid:3ac49751-ef87-461b-bc4c-685478efa0ff
Page Count                      : 23
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SWX-SMPICO

Navigation menu