Ubiquiti UINS U-Installer User Manual U Installer Quick Start Guide
Ubiquiti Networks, Inc. U-Installer U Installer Quick Start Guide
Ubiquiti >
Users Manual
Installer
Quick Start Guide
Hardware Overview
USB-C Port
Wi-Fi LED
PoE OUT
Port
Removable
Rubber
Casing
Battery
LEDs
Front View
Ports
PoE OUT Supplies 24V passive PoE to
the device being installed.
USB-C USB Type C port used for
recharging the internal battery.
LEDs
Wi-Fi
Lights blue if the U Installer has
a Wi-Fi connection to your mobile device.
Battery
Four blue LEDs indicate the
internal battery’s charge level:
Full charge
Low charge*
* Recharge the battery by connecting a power source,
such as mobile battery pack, to the USB-C port.
Back View
Buttons
Removable
Rubber
Casing
Clip
Buttons
Reset Ext
Power
Reset
Reset Ext
To reset the device connected
to the U Installer to factory defaults,
press this button while the device is
powered on. Hold the button for more
than 8 seconds until the LEDs on the
device flash.
[LED indication?]
Power Press to power the U Installer
on or off. [LED indication?]
Reset To reset the U Installer to factory
defaults, press and hold the Reset button
while the U Installer is powered on.
[LED indication?]
Configure a CPE Device
Use a mobile device to configure the
CPE device at the point of installation
via the U Installer’s Wi-Fi:
1. Power on the U Installer by pressing
the Power button. The [Wi-Fi? LED will
light blue?] when the power is on.
2. If the battery level is low, connect a
USB cable from a mobile power pack
or computer to the USB-C port of the
U Installer.
3. Connect an Ethernet cable to the
PoEOUT port on the U Installer.
4. Connect the other end of the cable to
the CPE device.
You have two options for configuration:
the U Mobile App and Web Portal.
Proceed to the appropriate instructions:
U Mobile App
1. Launch the U Mobile app on your
mobile device.
Note: If the app is not yet
installed on your mobile device,
download it from AppStore (iOS)
or Google Play™ (Android).
2. Follow the on-screen instructions to
configure the connected device.
Web Portal
1. Connect your mobile device’s Wi-Fi to
the U Installer SSID named:
U Installer:<MAC Address>.
2. Open a web browser on your
mobile device and go to
https://192.168.1.20
3. The login portal of the CPE device
will appear.
4. Log in and configure theCPE device
as needed.
Example Login Screen for CPE Device
Removing the U Installer
After you have configured the CPE
device, remove the U Installer:
1. Disconnect the Ethernet cable from
the device.
2. Connect the Ethernet cable from a PoE
adapter or switch to the device.
Safety Notices
3. Read, follow, and keep these instructions.
4. Heed all warnings.
5. Only use attachments/accessories specified by the
manufacturer.
WARNING: Do not use this product in location
that can be submerged by water.
WARNING: Avoid using this product during an
electrical storm. There may be a remote risk
of electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage,
frequency, and current requirements indicated on
the manufacturer’s label. Connection to a different
power source than those specified may result in
improper operation, damage to the equipment or
pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this
equipment. Service should be provided only by a
qualified service technician.
3. Contact a qualified electrician or the manufacturer
if there are questions about the installation prior to
connecting the equipment.
4. Protective earthing is provided by Listed AC adapter.
Building installation shall provide appropriate short-
circuit backup protection.
5. Protective bonding must be installed in accordance
with local national wiring rules and regulations.
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants
that the product(s) furnished hereunder (the “Product(s)”)
shall be free from defects in material and workmanship
for a period of one (1) year from the date of shipment by
UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation
and liability under the foregoing warranty shall be for
UBIQUITI NETWORKS, at its discretion, to repair or replace
any Product that fails to conform to the above warranty
during the above warranty period. The expense of removal
and reinstallation of any Product is not included in this
warranty. The warranty period of any repaired or replaced
Product shall not extend beyond its original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition
made thereto, except by Ubiquiti Networks, or
Ubiquiti Networks’ authorized representatives, or as
approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified
in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence,
abnormal physical, electromagnetic or electrical
stress, including lightning strikes, or accident;
(V) has been damaged or impaired as a result of using
third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing any
other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of
issuance of the RMA.
In addition, the above warranty shall apply only if: the
product has been properly installed and used at all times
in accordance, and in all material respects, with the
applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations,
shielded Ethernet cabling is used, and for indoor
installations, indoor cabling requirements are followed.
Returns
No Products will be accepted for replacement or repair
without obtaining a Return Materials Authorization (RMA)
number from UBIQUITI NETWORKS during the warranty
period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the
RMA process of UBIQUITI NETWORKS. Products returned
without an RMA number will not be processed and will be
returned freight collect or subject to disposal. Information
on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN,
UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR
THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE
PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER
REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS,
IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED
TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF
MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR
RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF
VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES
ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS
AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER
UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS
CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF
DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE
INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY
BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS,
CANCELLATIONS AND OTHER PROBLEMS INHERENT IN
THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI
NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY
INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY
FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET
LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE
FOREGOING. In addition, UBIQUITI NETWORKS does not
warrant that the operation of the Products will be error-
free or that operation will be uninterrupted. In no event
shall UBIQUITI NETWORKS be responsible for damages
or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of
products (including the Products) for buyer’s application
and/or failure of products (including the Products) to meet
government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW,
IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES,
AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT,
SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES (INCLUDING LOST PROFIT, LOST DATA,
OR DOWNTIME COSTS), ARISING OUT OF THE USE,
INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT,
TORT OR OTHER LEGAL THEORY, AND WHETHER OR
NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Note
Some countries, states and provinces do not allow
exclusions of implied warranties or conditions, so the
above exclusion may not apply to you. You may have
other rights that vary from country to country, state to
state, or province to province. Some countries, states
and provinces do not allow the exclusion or limitation of
liability for incidental or consequential damages, so the
above limitation may not apply to you. EXCEPT TO THE
EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY
TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND
ARE IN ADDITION TO, THE MANDATORY STATUTORY
RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE
(EMBEDDED IN THE PRODUCT) TO YOU. The United
Nations Convention on Contracts for the International
Sale of Goods shall not apply to any transactions
regarding the sale of the Products.
*640-00289-01*
640-00289-01
Compliance
FCC
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This radio transmitter FCC ID: SWX-UINS has been approved
by FCC to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Antenna Information: 2.4 GHz PIFA antenna, Gain: 1 dBi
5 GHz PIFA antenna, Gain: 2 dBi
Industry Canada
CAN ICES-3(B)/NMB-3(B)
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
Users should also be advised that high-power radars
are allocated as primary users (i.e. priority users) of the
band 5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.This radio
transmitter (IC: 6545A-UINS) has been approved by Industry
Canada to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Antenna Information: 2.4 GHz PIFA antenna, Gain: 1 dBi
5 GHz PIFA antenna, Gain: 2 dBi
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de façon
que la puissance isotrope rayonnée équivalente (PIRE) ne
dépasse pas ce qui est nécessaire pour une communication
réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est soumis
aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Les utilisateurs devraient également noter que radars haute
puissants sont alloués comme principaux utilisateurs (c’est-
à-dire les utilisateurs de priorité) des bandes et 5650 à 5850
MHz et que ces radars pourraient causer des interférences
ou dommages aux dispositifs LAN. Cet émetteur radio (IC:
6545A-UINS) a été approuvée par Industrie Canada pour
l’exploitation avec l’antenne types énumérés ci-dessous
avec le gain maximal admissible et requis l’impédance
de l’antenne pour chaque type d’antenne indiqué. Types
d’antenne non inclus dans cette liste, ayant un gain
supérieur au gain maximal indiqué pour ce type, sont
strictement interdits pour une utilisation avec cet appareil.
Informations d’antenne: 2.4 GHz PIFA antenne, Gain: 1 dBi
5 GHz PIFA antenne, Gain: 2 dBi
RF Exposure Warning
This device has been tested and meets applicable limits for
radio frequency (RF) exposure.
This device was tested with separation distance of 0 mm un-
der body-worn accessory (holster) operation condition. Al-
ways carry this device within a holster, to ensure exposure
levels remain at or below the as-tested levels
Cet appareil a été testé et respecte les limites applicables à
l'exposition aux fréquences radio (RF).
Cet appareil a été testé avec une distance de séparation de 0
mm sous l'état de fonctionnement des accessoires (étui) usé
par le corps. Portez toujours cet appareil à l'intérieur d'un étui
pour vous assurer que les niveaux d'exposition restent au
niveau ou sous les niveaux testés
Australia and New Zealand
Warning: This is a Class B product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
CE Marking
CE marking on this product represents the
product is in compliance with all directives that
are applicable to it.
product is in compliance with all directives that
are applicable to it.
RoHS/WEEE Compliance Statement
English
European Directive 2012/19/EU requires that the
equipment bearing this symbol on the product
and/or its packaging must not be disposed of with
unsorted municipal waste. The symbol indicates
that this product should be disposed of separately
from regular household waste streams. It is your
responsibility to dispose of this and other electric and
electronic equipment via designated collection facilities
appointed by the government or local authorities.
Correct disposal and recycling will help prevent
potential negative consequences to the environment
and human health. For more detailed information about
the disposal of your old equipment, please contact your
local authorities, waste disposal service, or the shop
where you purchased the product.
Deutsch
Die Europäische Richtlinie 2012/19/EU verlangt, dass
technische Ausrüstung, die direkt am Gerät und/oder an
der Verpackung mit diesem Symbol versehen ist, nicht
zusammen mit unsortiertem Gemeindeabfall entsorgt
werden darf. Das Symbol weist darauf hin, dass das
Produkt von regulärem Haushaltmüll getrennt entsorgt
werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte
über die dafür zuständigen und von der Regierung oder
örtlichen Behörden dazu bestimmten Sammelstellen
zu entsorgen. Ordnungsgemäßes Entsorgen und
Recyceln trägt dazu bei, potentielle negative Folgen
für Umwelt und die menschliche Gesundheit zu
vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie
sich bitte an die örtlichen Behörden oder städtischen
Entsorgungsdienste oder an den Händler, bei dem Sie
das Produkt erworben haben.
Español
La Directiva 2012/19/UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su
embalaje no deben eliminarse junto con otros residuos
urbanos no seleccionados. El símbolo indica que el
producto en cuestión debe separarse de los residuos
domésticos convencionales con vistas a su eliminación.
Es responsabilidad suya desechar este y cualesquiera
otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el
gobierno y las autoridades locales. Al desechar y reciclar
correctamente estos aparatos estará contribuyendo a
evitar posibles consecuencias negativas para el medio
ambiente y la salud de las personas. Si desea obtener
información más detallada sobre la eliminación segura
de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de
su zona o pregunte en la tienda donde adquirió el
producto.
Français
La directive européenne 2012/19/UE exige que
l’équipement sur lequel est apposé ce symbole sur le
produit et/ou son emballage ne soit pas jeté avec les
autres ordures ménagères. Ce symbole indique que
le produit doit être éliminé dans un circuit distinct
de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre
matériel électrique ou électronique par les moyens de
collecte indiqués par le gouvernement et les pouvoirs
publics des collectivités territoriales. L’élimination et
le recyclage en bonne et due forme ont pour but de
lutter contre l’impact néfaste potentiel de ce type de
produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre
ancien équipement, veuillez prendre contact avec les
pouvoirs publics locaux, le service de traitement des
déchets, ou l’endroit où vous avez acheté le produit.
Italiano
La direttiva europea 2012/19/UE richiede che le
apparecchiature contrassegnate con questo simbolo
sul prodotto e/o sull’imballaggio non siano smaltite
insieme ai rifiuti urbani non differenziati. Il simbolo
indica che questo prodotto non deve essere smaltito
insieme ai normali rifiuti domestici. È responsabilità
del proprietario smaltire sia questi prodotti sia le altre
apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo
o dagli enti pubblici locali. Il corretto smaltimento
ed il riciclaggio aiuteranno a prevenire conseguenze
potenzialmente negative per l’ambiente e per la
salute dell’essere umano. Per ricevere informazioni
più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a
contattare gli enti pubblici di competenza, il servizio
di smaltimento rifiuti o il negozio nel quale avete
acquistato il prodotto.
Declaration of Conformity
Česky
[Czech]
UBIQUITI NETWORKS tímto prohlašuje, že toto
UBIQUITI NETWORKS zařízení, je ve shod se
základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Hermed, UBIQUITI NETWORKS, erklærer at denne
UBIQUITI NETWORKS enhed, er i overensstemmelse
med de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF.
Nederlands
[Dutch]
Hierbij verklaart UBIQUITI NETWORKS, dat deze
UBIQUITI NETWORKS apparaat, in overeenstemming
is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
English
Hereby, UBIQUITI NETWORKS, declares that this
UBIQUITI NETWORKS device, is in compliance with
the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Eesti
[Estonian]
Käesolevaga UBIQUITI NETWORKS kinnitab, et antud
UBIQUITI NETWORKS seade, on vastavus olulistele
nõuetele ja teistele asjakohastele sätetele direktiivi
1999/5/EÜ.
Suomi
[Finnish]
Täten UBIQUITI NETWORKS vakuuttaa, että tämä
UBIQUITI NETWORKS laite, on yhdenmukainen
olennaisten vaatimusten ja muiden sitä koskevien
direktiivin 1999/5/EY.
Français
[French]
Par la présente UBIQUITI NETWORKS déclare que
l’appareil UBIQUITI NETWORKS, est conforme aux
exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.
Deutsch
[German]
Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses
UBIQUITI NETWORKS Gerät, in Übereinstimmung
mit den grundlegenden Anforderungen und den
anderen relevanten Vorschriften der Richtlinie
1999/5/EG befindet.
Ελληνική
[Greek]
Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει
ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε
συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές
σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ.
Magyar
[Hungarian]
Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a
UBIQUITI NETWORKS készülék megfelel az alapvető
követelményeknek és más vonatkozó 1999/5/EK
irányelv rendelkezéseit.
Íslenska
[Icelandic]
Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITI
NETWORKS tæki er í samræmi við grunnkröfur og
önnur viðeigandi ákvæði tilskipun 1999/5/EB.
Italiano
[Italian]
Con la presente, UBIQUITI NETWORKS, dichiara che
questo dispositivo UBIQUITI NETWORKS, è conforme
ai requisiti essenziali ed alle altre disposizioni
pertinenti della direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI
NETWORKS ierīce, ir saskaņā ar būtiskajām prasībām
un citiem attiecīgiem noteikumiem Direktīvā
1999/5/EK.
Lietuviškai
[Lithuanian]
UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI
NETWORKS įrenginys atitinka esminius reikalavimus
ir kitas 1999/5/EB Direktyvos nuostatas.
Malti
[Maltese]
Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan
il-mezz UBIQUITI NETWORKS huwa konformi mar-
rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn
ta ‘Direttiva 1999/5/KE.
Norsk
[Norwegian]
Herved UBIQUITI NETWORKS, erklærer at denne
UBIQUITI NETWORKS enheten, er i samsvar med
de grunnleggende kravene og andre relevante
bestemmelser i direktiv
1999/5/EF.
Polski
[Polish]
Niniejszym, Ubiquiti Networks, oświadcza, że
urządzenie UBIQUITI NETWORKS, jest zgodny z
zasadniczymi wymaganiami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/WE.
Português
[Portuguese]
UBIQUITI NETWORKS declara que este dispositivo
UBIQUITI NETWORKS, está conforme com os
requisitos essenciais e outras disposições da
Directiva 1999/5/CE.
Română
[Romanian]
Prin prezenta, UBIQUITI NETWORKS declară că acest
dispozitiv UBIQUITI NETWORKS este în conformitate
cu cerințele esențiale și alte prevederi relevante ale
Directivei 1999/5/CE.
Slovensky
[Slovak]
Týmto
UBIQUITI NETWORKS
, prehlasuje, že toto
UBIQUITI NETWORKS
zariadenie, je v súlade so
základnými požiadavkami a ďalšími relevantnými
ustanoveniami smernice 1999/5/ES.
Español
[Spanish]
Por medio de la presente UBIQUITI NETWORKS
declara que este dispositivo UBIQUITI NETWORKS,
cumple con los requisitos esenciales y cualesquiera
otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Svenska
[Swedish]
Härmed UBIQUITI NETWORKS, intygar att denna
UBIQUITI NETWORKS enhet är i överensstämmelse
med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv
1999/5/EG.
©2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti,
Ubiquiti Networks, the UbiquitiU logo, the Ubiquiti beam
logo, airMAX, airOS, and U Installer are trademarks or
registered trademarks of UbiquitiNetworks,Inc. in the
United States and in other countries. All other trademarks
are the property of their respectiveowners.
AI031617
Online Resources
Support support.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com
www.ubnt.com